Hino Nv8j 2015

Vehicle Details: Recalls, Service Bulletins

Below you will find all available information on the 2015 HINO NV8J.

Manufacturer	Known WMI(s)	Fuel Type
HINO

HINO VIN Decoder

Use the box here to look up VINs from HINO as well as other manufacturers

NHTSA Mandated Recalls

Recall 2016421 [Canada]: Brakes

Recall 2016397 [Canada]: Brakes

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Recalls are also available on the Complaints page

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

TT-14-033 - ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION: When replacing an engine block with service part no., 11401e0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have these 2 o
TT-14-017 - EQUIPMENT: Bendix? Air dryer service
SB-14-020 - STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS: When replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
SB-14-012 - POWER TRAIN: A subject vehicle may exhibit an illuminated check engine lamp with dtc (diagnostic trouble code) P0421 (catalyst efficiency below threshold). The engine ecu may falsely detect an issue with the atc (after turbo catalyst) with the current e
SB-15-010 - EQUIPMENT ADAPTIVE/MOBILITY: Some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the egr (exhaust gas recirculation) butterfly plate with a repeat P1604 dtc (diagnostic trouble code) stored in the engine ecu. A heated egr valve h
PA-2014-073 - EQUIPMENT: 2015 all-makes marketing and advertising support package
167-T1514-12 - STRUCTURE:BODY: Tt-15-016 the purpose of this publication is to communicate the standard measuring positions on the hino chassis. In some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards t
167-T1513-12 - POWER TRAIN: Tt-15-014 the transmission dtc?S P0974 and P0986, may be found on 12my-15my coe models. There could also be a complaint of low power and erratic shifting. These diagnostic codes may be set due to low voltage between the transmission case an
167-T0706-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 07 - 006 voltage drop test
167-B1312-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-13-009 this bulletin is to inform dealers and workshops of proper paint codes for all hino models. All models
167-B1307-12 - POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL): 13-008 design change of the idler gear case and idler gear bolt. Abnormal load such as a stuck supply pump was applied to gear train then causing the bolt to loosen. Therefore, an enhancement to the case and bolt were carried out. The idle
167-R1603-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Scb-001-16 a subject vehicle may exhibit an illuminated check engine lamp with dtc (diagnostic trouble code) P14BF ?Egr (exhaust gas recirculation) valve controller temperature sensor 1, 2 rationality. The egr valve may falsely detect this
167-B1623-12 - FUEL SYSTEM, GASOLINE: Sb-16-019 an enhanced fuel cut valve is available to address a potential sticking condition that results in excess residual pressure in the dosing injector (7thinjector) supply pipe. A sticking fuel cut valve may result in the following dt
167-B1621-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-16-010 correction of the inspection of the dpr filter.
167-B1619-12 - SERVICE BRAKES, HYDRAULIC: Sb-16-006 some vehicles built before january 2016 and equipped with a leaf spring rear suspension may experience a dislodged or missing spring pad. As an enhancement, the rear axle leaf spring hanger design has been changed to eliminate the
167-B1618-12 - FUEL/PROPULSION SYSTEM (PWS): Addition of detailed explanation of the fuel pipe installation.
167-T1429-12 - ENGINE (PWS): Tt-14-033 when replacing an engine block with service part no., 11401e0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have
167-T1416-12 - SERVICE BRAKES, AIR: Tt-14-017 the bendix ad-is (p/n: k154348) air dryer on air brake equipped vehicles contains several serviceable components. This replacement purge valve can eliminate the need to replace the whole air dryer assembly. These serviceable c
167-B1616-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-16-004 1. In the event that a subject vehicle exhibits an illuminated check engine lamp and dtc?S P2201, P2214, P206B, P207F, or P20EE are stored in the dcu, the nox sensor may have failed due to a cracked nox sensor heating element. Fo
167-B1602-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-16-015 enhanced dcu (dosing control unit) software has been released.Illumination of the check engine light. The dcu may falsely detect an issue and record any of the 3 following dtc?S in the dcu. P142A(def pump temperature sensor - out
167-B1601-12 - FUEL SYSTEM, GASOLINE: Sb-16-007 if dtc(diagnostic trouble code) P0611:fuel injector driver charge circuit - circuit low has set in the engine ecu(electronic control unit) and the workshop manual diagnostic procedure has led to ecu replacement, an enhanced engine
167-B1528-12 - EQUIPMENT:ELECTRICAL: Sb-15-031 foreign debris in the def (diesel exhaust fluid) tank may cause the scr (selective catalyst reduction) system to malfunction. This can result in dtc?S (diagnostic trouble codes) P20E8 or P20E9 - def pressure abnormality. An inlet
167-B1527-12 - EQUIPMENT:ELECTRICAL: Sb-15-030 on subject vehicles, the mil (malfunction indicator lamp) may illuminate with dtc (diagnostic trouble code) U02A2 stored in the engine ecu. This may be due to a malfunction of the def (diesel exhaust fluid) tank sensor assembly. P
167-B1523-12 - ENGINE AND ENGINE COOLING: Sb-15-026 a subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. An improved head gasket has been made available as a servic
167-B1518-12 - STRUCTURE:BODY: Sb-15-019 reinforcement brackets and fiberglass repair methods have been made available to address hood crack concerns. In the event a subject vehicle experiences cracking of the hood near the hinges, this repair procedure should be used
167-B1515-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE: Sb-15-016 new parts are available to prevent repeat exhaust manifold stud failures on the j05 engine. This bulletin provides instructions for installing longer manifold studs at the #4 cylinder location.
167-B1511-12 - STEERING: STEERING WHEEL/HANDLE BAR: Sb-15-011 the following tsb (technical service bulletin) outlines the inspection method for steering wheel free play and the adjustment procedure of the steering gear.
167-B1510-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE): Sb-15-010 some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the egr (exhaust gas recirculation) butterfly plate with a repeat P1604 dtc (diagnostic trouble code) stored in the engine ecu. A heated e
167-B1504-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-15-003 correction of workshop manual for hino 2015my (revision of troubleshooting procedure for the dtc P0421)
167-B1503-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-15-002 correction of workshop manual for 2013 - 2015my (revision of troubleshooting procedure for the dtc P2123)
167-B1414-12 - STRUCTURE:BODY:HOOD: Sb-14-020 when replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
167-B1426-12 - STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS: Sa-14-026 the broken hood grille procedure (sb-14-020) has been revised to reuse the grille nuts (sz17906009) if possible. There is a limited quantity of the nuts available and it has been confirmed that the nuts are reusable. The revised p
167-B1423-12 - EQUIPMENT:ELECTRICAL: Sb-14-005 2011my-2015my conventional keyless entry programming
167-B1418-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-14-012 a subject vehicle may exhibit an illuminated check engine lamp with dtc (diagnostic trouble code) P0421 (catalyst efficiency below threshold). The engine ecu may falsely detect an issue with the atc (after turbo catalyst) with the
167-B1423-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-14-005 2011my-2015my conventional keyless entry programming
167-B1418-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-14-012 a subject vehicle may exhibit an illuminated check engine lamp with dtc (diagnostic trouble code) P0421 (catalyst efficiency below threshold). The engine ecu may falsely detect an issue with the atc (after turbo catalyst) with the
167-B1401-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL: Sb-14-029 correction of workshop manual for 2011 - 2015 my. Troubleshooting information and inspection procedures for the dtc P2201 and P2214 were revised.
167-B1408-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL: Sb-14-028 correction of workshop manual for 2011- 2015 my. Troubleshooting information and inspection procedure of the dtc/P207F were revised.
167-B1408-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL: Sb-14-028 correction of workshop manual for 2011- 2015 my. Troubleshooting information and inspection procedure of the dtc/P207F were revised.
167-R1407-12 - SERVICE BRAKES, HYDRAULIC: T0280 during installation of the air pressure sensors on the air tanks, it is possible that they could have been damaged causing incorrect air pressure readings.
167-T0610-12 - LIGHTING (PWS): 06 - 002 no throttle response. Once a burnt out tail lamp filament touches a stop lamp filament, the current goes thru the stop lamp circuit causing the ecu to think that the brakes are applied. Therefore stopping acceleration control.
167-B0803-12 - WHEELS:LUGS/NUTS/BOLTS/STUDS: Sb - 08 - 005 this document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
167-B0602-12 - ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER: Sb ? 06 - 002 fuel filter usage. This bulletin provides technical information for proper fuel filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel fil
167-B0601-12 - ENGINE AND ENGINE COOLING: Sb ? 06 - 001 design change of engine oil cooler housing. The casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. These grooves aid in the retentio
167-B0508-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb - 05 - 005 proper maintenance procedures for grease lubricated front axles
167-B0506-12 - ENGINE (PWS): Sb ? 05 - 008 this document is to inform the dealers about the addition of the pressure sensor cover and related part for the j08e engine.
167-B0505-12 - EQUIPMENT ADAPTIVE/MOBILITY: Sb ? 05 - 007 design change of water pipe for j08e
167-B0504-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Sb - 05 - 003 this document is to inform dealers and workshops on procedures to activate exhaust brake operation.
167-B0503-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb ? 05 - 010 correction to workshop manuals for the j08e engine. A) resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 ohms b) illustration of the air intake pre-heater terminal should be revised. C) r
167-B0502-12 - ELECTRICAL SYSTEM: Sb - 05 - 004 speedometer recalibration. This document is to inform of the procedure to calibrate the pulse adjust module whenneeded (ex. Tire size change, rear carrier ratio change).
167-B0501-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 05 - 011 corrections to workshop manuals for j08 engines. The standard gap between ends of the second piston ring and the oil ring.
167-R1701-03 - ELECTRICAL SYSTEM:SOFTWARE: 17my vehicles contain the function to monitor pm sensor performance, however because the threshold for detection logic is not appropriate, the engine ecu may not detect a malfunction of the pm sensor. The following procedure provides direct
167-T1701-03 - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: Beginning with the 2017 model year, hino changed the standard battery from a group 27 to a group 31. In the event that a group 27 battery must be replaced, it is recommended to use the group 31 as the service replacement for 2014my and newe