Lincoln Mkz 2008

• Recall 229556 [USA]: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
  Ford motor company (ford) is recalling certain 2007-2011 ranger, 2006-2012 fusion, lincoln zephyr, lincoln mkz, 2006-2011 mercury milan, 2007-2010 ford edge, and lincoln mkx vehicles. The driver's side air bag inflator may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
  ford will notify owners, and dealers will replace the driver-side airbag inflator or module with an alternate one, free of charge. Owner notification letters were mailed on april 9, 2021 for the passenger side, and november 14, 2022 for the driver side. Owners may contact ford customer service at 1-866-436-7332. Ford's number for this recall is 21s12.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 150547 [USA]: If the valves do not properly close, additional brake pedal travel may be required to stop the vehicle, increasing the risk of a crash.
  Ford motor company (ford) is recalling certain 2006-2010 ford fusion, mercury milan, lincoln zephyr and mkz vehicles. The valves within the abs hydraulic control units (hcu) may react with brake fluids containing specific corrosion preventative additives. This reaction may cause the valves to not close properly.
  ford will notify owners, and dealers will flush the brake system with dot 4 fluid and install a new brake fluid reservoir cap. In addition, the hcu will be tested to detect a possible stuck valve condition, replacing the hcu as necessary. All services will be performed free of charge. The recall began april 1, 2021. Owners may contact ford customer service at 1-866-436-7332. Ford's number for this recall is 19s54.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 120693 [USA]: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
  Ford motor company (ford) is recalling certain 2012 ford fusion and mustang and lincoln zephyr and mkz vehicles originally sold, or ever registered, in alabama, california, florida, georgia, hawaii, louisiana, mississippi, south carolina, texas, puerto rico, american samoa, guam, the northern mariana islands (saipan), and the u.S. Virgin islands, or "zone a." additionally, unless included in "zone a" above, ford is recalling certain 2009 ford ranger, edge, fusion and mustang, lincoln mkx, mkz and zephyr and mercury milan vehicles originally sold, or ever registered, in arizona, arkansas, delaware, district of columbia, illinois, indiana, kansas, kentucky, maryland, missouri, nebraska, nevada, new jersey, new mexico, north carolina, ohio, oklahoma, pennsylvania, tennessee, virginia and west virginia, or "zone b." additionally, unless included in "zone a" or "zone b" above, ford is recalling certain 2007-2008 ford ranger, edge and lincoln mkx, 2006-2008 ford fusion, mercury milan, lincoln zephyr and mkz, 2005-2008 ford mustang and 2005-2006 ford gt vehicles originally sold, or ever registered, in the states of alaska, colorado, connecticut, idaho, iowa, maine, massachusetts, michigan, minnesota, montana, new hampshire, new york, north dakota, oregon, rhode island, south dakota, utah, vermont, washington, wisconsin and wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
  ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Interim letters informing owners of the recall and that parts are not yet available began mailing march 1, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact ford customer service at 1-866-436-7332. Ford's number for this recall is 19s01.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 104394 [USA]: The floor mat could shift such that it could interfere with the accelerator pedal, preventing its return to an idle position, which could result in unintended vehicle speeds, increasing the risk of a crash.
  Ford motor company (ford) is recalling certain all weather driver side accessory floor mats sold for use in model year 2006-2011 ford fusion and mercury milan, 2006 lincoln zephyr, and 2007-2011 lincoln mkz vehicles manufactured november 9, 2007, through october 31, 2010. The affected floor mats may move and possibly interfere with the accelerator pedal.
  ford will notify owners, and dealers will install new replacement mats, free of charge. The recall began in july 2014. Owners may contact ford's customer service at 1-800-392-3673. Ford's number for this recall is 14s07. Note: vehicles built after october 31, 2010, while potentially equipped with the same floor mats, are equipped with a brake over accelerator (boa) feature that prevents simultaneous accelerator and brake application, allowing the vehicle to be safely stopped by pressing firmly and steadily on the brake pedal.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 2021077 [Canada]: Airbag
  Issue: this recall is for certain vehicles that had the driver-front and/or passenger-front airbag inflator replaced after a collision or theft. An obsolete airbag may have been installed. On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the driver-front airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Safety risk: if the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective action: the company will notify owners by mail and instruct you to take your vehicle to a ford dealer to inspect the driver and/or passenger airbag inflator or module and replace it, if necessary. Note: the canadian climate results in the propellant degrading slowly. This recall is being conducted as a precaution to address future risk. It is expected that all airbag inflators will be replaced before their function would be affected.

  Show Content

• Recall 2021029 [Canada]: Airbag
  Issue: on certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the driver-front airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Safety risk: if the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective action: ford will notify owners by mail. The corrective actions for this recall are under development. Note: the canadian climate results in the propellant degrading slowly. This recall is being conducted as a precaution to address future risk. It is expected that all airbag inflators will be replaced before their function would be affected.

  Show Content

• Recall 2019665 [Canada]: Brakes
  Issue: on certain cars, a problem with the hydraulic control unit for the anti-lock brake system (abs) could cause increased brake pedal travel. Safety risk: increased brake pedal travel could increase the risk of a crash. Corrective actions: the company will notify owners by mail and instruct you to take your vehicle to a ford or lincoln dealer to inspect the abs module assembly. The system will be flushed with dot 4 brake fluid, and if necessary, the hydraulic control unit will be replaced. Dealers will also replace the dot 3 reservoir cap with a new dot 4 cap.

  Show Content

• Recall 2019005 [Canada]: Airbag
  Issue: on certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the passenger-front airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Safety risk: if the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective actions: owners will be notified by mail and instructed to take their vehicle to a dealer to have the passenger-front airbag inflator replaced. Note: the canadian climate results in the propellant degrading slowly. This recall is being conducted as a precaution to address future risk. It is expected that all airbag inflators will be replaced before their function would be affected. Additional note: this recall supersedes recalls 2016-347 (ford safety improvement program 16s26), 2017-024 (ford recall 17s01) and 2018-035 (ford recall 18s01). Vehicles repaired under the previous recalls do not require repair under this recall.

  Show Content

• Recall 2017024 [Canada]: Airbag
  On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, could eventually degrade the propellant contained in the passenger frontal airbag. This could cause the airbag to deploy with more force than normal. As a result, if the vehicle were involved in a collision that warrants airbag deployment, metal fragments could be propelled toward vehicle occupants, and the airbag assembly could be damaged, preventing proper function. These issues could increase the risk of injury. Correction: depending on the model, dealers will either replace the passenger frontal airbag inflator or airbag assembly. Note: canadian climate results in the propellant degrading slowly. The recall is being conducted as a precaution to address future risk, and is expected to replace airbag inflators before their function would be affected. Additional note: this recall is superseded by recall 2019005 (ford recall 19s01). Please see recall 2019005 for more information.

  Show Content

• Recall 2016347 [Canada]: Airbag
  Ford canada is conducting a voluntary safety improvement program involving passenger airbag inflators in certain vehicles that were originally sold or ever registered in certain high humidity areas of the united states equipped with takata airbags. Ford will replace the driver or passenger inflator on affected vehicles, depending on the vehicle involved. Owners who believe their vehicles may have been originally purchased or registered in the states of new jersey, delaware, district of columbia, maryland, pennsylvania, ohio, indiana, illinois, virginia, west virginia, kentucky, missouri, nebraska, kansas, oklahoma, arkansas, tennessee, north carolina, nevada, arizona, new mexico, california, texas, louisiana, mississippi, alabama, georgia, south carolina, florida, hawaii, puerto rico or the u.S. Virgin islands should contact a ford dealer. This action is not being conducted under the requirements of the motor vehicle safety act. Note: this safety improvement program is superseded by recall 2019005 (ford recall 19s01). Please see recall 2019005 for more information.

  Show Content

• Recall 2014195 [Canada]: Accessories
  A safety defect may exist in ford aftermarket all-weather floor mats sold as accessories or service replacement parts for 2006-2011 ford fusion, lincoln zephyr, and lincoln mkz vehicles. The floor mats are secured by a single retention device, which could allow the driver's floor mat to move out of position and interfere with the accelerator pedal.  if this occurs, the accelerator pedal could fail to return to idle.  this could result in a crash causing injury and/or property damage.  correction: dealers will replace ford aftermarket all-weather floor mats with an updated design having two retention devices.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Extended braking distance investigation # EA18002

  On april 18, 2018, the office of defects investigation (odi) opened engineering analysis (ea) 18-002 to investigate reports of braking concerns in model year (my) 2006-12 ford fusion and lincoln mkz, and my 2006-11 mercury milan vehicles manufactured with continental automotive system’s abs hydraulic control units (hcus). Complainants report that after an abs braking event (initiated by slippery or uneven surfaces) the brake pedal moved towards the floor and the vehicle stopping distance increased beyond driver expectations.Inside the hcu are four hydraulic normally closed (nc) valves with zinc-coated moving armatures that control the flow of brake fluid. Unstable brake fluid can degrade over time, allow the brake fluid to gel, and corrosion to form on the armatures. The high-viscosity gelation and corrosion can cause the armatures to become stuck (open). In some cases, braking returns to normal when the armature(s) subsequently become unstuck. The intermittent condition proves difficult to diagnose with complainants reporting having (non-hcu) repairs conducted only to have the condition return.During the investigation, 14 hcus from complaint vehicles were recovered, including seven from reported crashes. Nhtsa’s vehicle research and test center (vrtc) disassembled the hcus, removed the four nc valves in each, and confirmed 22 of the 56 nc valves contained stuck armatures. On seven of the 14 hcus, both front wheel armatures were stuck, on nine of the 14 hcus two or three armatures were stuck. And 52 of the 56 nc armatures exhibited corrosion of the zinc coating. Forces required to extract stuck armatures from the valve sleeve were measured to range from 1.1 to 18.0 lbs. Vrtc also conducted abs braking tests on a variety of test surfaces that showed hcu failures cause increases in pedal travel and braking distances. Testing also showed that if the driver was able to apply four times the brake pedal force and two times the brake pedal travel, then high-vehicle decelerations could be achieved, however, single or multiple wheel lockups were also occurring.Based on ford’s response to odi’s july 20, 2018 information request letter, and complainants reports to nhtsa, odi identified a population of vehicles with an elevated level of field failure compared to vehicles produced both before and after.Further evaluation of ford’s response identified that the brake fluid used to produce these vehicles, a specific formulation of a dot3 fluid provided by cci corporation between february 2006 and july 2009, differed from the brake fluid used in other vehicle populations. Odi used the correlation of fluid specification and elevated field failures to identify a vehicle population exhibiting a defect trend. The complaints, crashes and injuries cited above, and the 14 recovered hcus involve vehicles from this population.On december 18, 2019, ford submitted safety recall (19v-904) to remedy hcu failures on the my 2006-2010 ford fusion, lincoln mkz, and mercury milan vehicles manufactured with the suspect cci brake fluid formulation. Ford will function test the hcu and replace the dot 3 brake fluid with an improved dot 4 brake fluid. If the hcu fails the function test, ford will install an hcu with a different armature coating (black oxide). Hcus with black oxide coating were fully phased into ford’s new vehicle production by my 2016; these hcus do not appear to be experiencing armature corrosion. Odi notes that the non-recalled ea18-002 subject vehicles, which were manufactured with a different specification brake fluid, did not display an elevated level of field failures like the recalled vehicles.Based on available information, ford’s recall addresses the unreasonable risk to motor safety. Accordingly, the investigation is closed. The odi reports cited above can be reviewed at nhtsa.Gov under the identification (odi) numbers found in the attached list.
  

  Show Content

• Floor mat interference with accelerator investigation # EA12009

  On may 27, 2014, ford motor company submitted recall 14e-028 (ford recall #14s07) to correct a safety-related problem with certain drivers side ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year ford fusion, mercury milan, lincoln zephyr, and lincoln mkz vehicles built at hermosillo assembly plant (hap) from november 9, 2007, to october 31 ,2010.Nhtsa testing determined that the original accessory all-weather mat with a single retention clip (figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the office of defects investigation (odi) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by ford and lincoln dealers directly to customers as an optional accessory equipment item or, beginning in november 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected drivers side all weather floor mats were sold worldwide; either over the counter through ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their ford or lincoln dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected ford drivers side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The voqs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
  

  Show Content

• Accel pedal interference - acc floormat investigation # PE10019

  Unsecured mats may interfere with accelerator pedal return to idle. A heel blocker in the floor pan provides a platform that may lift an unsecured mat into contact with the pedal. Ford introduced new pedals as a running change early in model year (my) 2010 vehicles. Analysis of complaints received by odi and ford show elevated rates of pedal entrapment incidents in my 2008 through early 2010 production vehicles. Incidents typically occur following hard pedal applications to pass slower traffic or when merging into faster traffic. Drivers allege continued high engine power after releasing the accelerator pedal and difficulty braking, including reports that the incident was controlled by shifting to neutral or turning the engine off. Drivers and service technicians reference observing evidence of mat interference or note unsecured ford or aftermarket all weather floor mats in post-incident inspections.Based on information gathered during the preliminary evaluation the population being investigated has been narrowed to model years 2008 to 2010.This investigation has been upgraded to an engineering analysis on my 2008 through early-2010 vehicles (produced through september 2009) to further assess the scope, frequency and safety consequences of the alleged defect.The voqs associated with the opening of this engineering analysis are: 10479693, 10415911, 10379562, 10372674, 10345830, 10342572, 10339330, 10335336, 10334211, 10332233, 10331160, 10329659, 10327597, 10320011, 10232027, 10214131
  

  Show Content

• Tire valve cracking investigation # PE08060

  On october 14, 2008, odi opened pe08-060 to investigate allegations of cracked and leaking snap-in tire valves in model year (my) 2007 vehicles manufactured by ford motor company.The valves were supplied to ford by topseal auto-parts, a subsidiary of the shanghai baolong automotive corporation in china.Valves made by topseal for aftermarket sale were the subject of two recent safety recalls by tech international (08t-018) and dill air controls (08t-028), the latter of which was investigated by odi in pe08-036 and ea08-022.The defect conditions addressed by the aftermarket tire valve recalls both involved inadequate resistance to ozone cracking due to issues with the supply of anti-ozonant chemicals to topseal for a period from july to mid-november 2006.The aftermarket valves were compounded with a blend of epdm and natural rubber, using a relatively low percentage of epdm (epdm provides inherent resistance to ozone cracking).Hence, the need for anti-ozonant chemicals and the problems with cracking when those chemicals were missing or out of specification in some lots of valves.Both recall campaigns involved inspection programs to identify and replace valves with visible surface cracking.Although the topseal valves supplied to ford also appear to have been affected by the anti-ozonant supply issues in mid to late-2006, ford indicated that its valves were made at a different topseal production line and were compounded with a higher percentage of epdm rubber to meet more stringent specifications from ford.Odis analysis of complaint and warranty data provided by ford showed that problems with cracked tire valves were significantly higher for my 2007 vehicles produced from december 2006 through march 2007.Ford responded by implementing changes in its material specifications for snap-in rubber tire valves and also increasing the quality and acceptance standards for valves imported for use in its vehicles.While the complaint and warranty claim rates are elevated for subject vehicles produced from december 2006 through march 2007, the rates of leaking valves are well below one percent of production for each of the peak months for all of the affected models.A substantial majority of the subject vehicles are equipped with tire pressure monitoring systems (tpms) which warn the driver when any tire pressures drops below 25 percent of recommended inflation pressure. As outlined in a letter to odi dated april 6, 2009, ford has agreed to send letters to owners of certain my 2007 and 2008 ford, lincoln and mercury vehicles to provide information about the cracking concern. Letters will be sent to owners of vehicles built from november 2006 through may 2007.Owners can opt for a free dealer inspection.Valves exhibiting surface cracks or air leakage related to ozone attack will be replaced by ford under its normal warranty terms.Ford expects to send the letter by approximately mid-may 2009. Based on the use of tpms in the majority of subject vehicles and the relatively low rates of repairs associated with leaking valves and resultant tire damage, odi believes that the actions ford has agreed to take will provide effective and expeditious resolution for vehicles that were built during the period when valves with inadequate resistance to ozone cracking were most likely to have been used in vehicle production.Further investigation of this matter would not be an efficient allocation of agency resources.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist.The agency will continue to monitor complaints and other information relating to the alleged defect in the subject vehicles and take further action in the future if warranted.
  

  Show Content

2008 lincoln mkz> consumer writes in regards to hydraulic control unit and anti-lock braking system. The consumer stated the vehicle began experiencing intermittent abs and stability control warning light illumination. The consumer was informed the failure was unrelated to the recall.

Recall notice19s54. Hcu unit gone. Part is on back order 889 cars are waiting on this part. Car has been in dealership for two weeks with no eta of parts delivery. People like me are not giving rental to cover until car gets fix we are financially stuck ford is not offering rental car or nothing. Car is at leith lincoln for almost two weeks. Please amend to cover for loss of use or rental car.

Tl* the contact owns a 2008 lincoln mkz. The contact stated while driving 35 mph, the brake pedal was depressed and went to the floor. The contact stated that the braking distance was extended. There was no warning light illuminated. The vehicle was taken to beau townsend ford lincoln (1020 w national rd, vandalia, oh 45377, (937) 898-5841) to be diagnosed. The contact was informed that the brake fluid needed to be replaced. The vehicle was repaired. Upon investigation, the contact associated the failure with nhtsa campaign number: 19v904000 (service brakes, hydraulic). The failure persisted. The manufacturer was informed of the failure and informed the contact they were unable to offer any assistance. The failure mileage was approximately 104,000.

Encountered extended brake pedal range and pressure required to properly apply brakes after engaging abs while driving on slippery surface. Following incident, brake fluid reservoir checked full, and condition continued.

Encountered extended brake pedal range and pressure required to properly apply brakes after engaging abs while driving on slippery surface. Following incident, brake fluid reservoir checked full, and condition continued.

Driver side front seat heater do not work, but passenger front seat do work. Passenger side low beam light stopped working.

Driver side front seat heater do not work, but passenger front seat do work. Passenger side low beam light stopped working.

Tl* the contact owns a 2008 lincoln mkz. The contact received notification of nhtsa campaign number: 19v904000 (service brakes, hydraulic) however, the part to do the recall repair was unavailable. The vehicle was taken to classic ford (8540 tyler blvd, mentor, oh 44060, (440)266-3000) where it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact stated that unknown brake parts were replaced after the brake pedal was depressed and went to the floorboard. The approximate failure mileage was 94,608. Vin tool confirms parts not available.

Tl* the contact owns a 2008 lincoln mkz. The contact received notification of nhtsa campaign number: 19v904000 (service brakes, hydraulic) however, the part to do the recall repair was unavailable. The vehicle was taken to classic ford (8540 tyler blvd, mentor, oh 44060, (440)266-3000) where it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact stated that unknown brake parts were replaced after the brake pedal was depressed and went to the floorboard. The approximate failure mileage was 94,608. Vin tool confirms parts not available.

Common OBD-II Error Codes

• P0351 [1] Ignition Coil A Primary/Secondary Circuit Malfunction
• P0352 [1] Ignition Coil B Primary/Secondary Circuit Malfunction
• P0353 [1] Ignition Coil C Primary/Secondary Circuit Malfunction
• P0354 [1] Ignition Coil D Primary/Secondary Circuit Malfunction
• P0355 [1] Ignition Coil E Primary/Secondary Circuit Malfunction
• P0715 [1] Input/Turbine Speed Sensor A Circuit Malfunction
• P0717 [1] Input/Turbine Speed Sensor A Circuit No Signal
• P0720 [1] Output Speed Sensor Circuit Malfunction
• P0721 [1] Output Speed Sensor Range/Performance
• P0722 [1] Output Speed Sensor No Signal