Mack Cv 2006

• Recall 71545 [USA]: There is a possibility that the pivot bolt can become loose without the driver's knowledge. when this occurs, the driver could drive away and the trailer could become disengaged, increasing the risk of a crash.
  On certain trucks equipped with a saf holland simplex fifth wheel, the lever arm pivot bolt may have been over tightened. An over tightened pivot bolt can distort the pivot bolt spacer sleeve, which may prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin.
  dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer free of charge. The recall began on january 28, 2008. Owners may contact mack trucks at 1-800-528-6586.
  mack trucks recall no. SC0331.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 31984 [USA]: This condition can cause a delay in the application of the spring brakes to park the vehicle after the operator pulls the dash valve button. these conditions can occur without warning, leading to unintended vehicle rollaway, brake drag, or in the case of loss of primary circuit, inability to modulate the spring brakes.
  On certain trucks equipped with parker single check valves (scv) provided by bendix. The defect exists in the parker scv that connects with the supply port of the sr-7 spring brake modulating valve. After prolonged use of the parker scv, the valve body retainer may become excessively worn and eventually break apart. Pieces of the parker scv can become lodged inside the sr-7 spring brake modulating valve, potentially causing either leakage out of the sr-7 valve or preventing air from properly exhausting from the sr-7 valve.
  mack is working with bendix to replace the parker single check valve. The recall began on january 9, 2008. Owners may contact bendix at 1-440-329-9000 or mack at 1-800-528-6586.
  mack recall no. SC0334 (sC0327).Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 88377 [USA]: This could delay or failure in applying the parking brakes which could result in a vehicle roll away, increasing the risk of a crash.
  On certain trucks equipped with bendix sr-7 spring brake modulating valves, the internal rubber check valve may leak causing a delay in the application of the spring brakes to park the vehicle after the operator pulls the dash valve button.
  mack is working with bendix to repair these vehicles (please see 07e037). Bendix will install a check valve repair kit for the affected sr-7 spring brake modulating valve free of charge. The recall began on january 10, 2008. Owners may contact bendix at 1-440-329-9000 or mack at 1-800-528-6586.
  mack recall no. SC0335 (sC0328).Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 46840 [USA]: The purpose of this standard is to insure safe braking performance under normal and emergency conditions.
  Certain trucks equipped with a front glad hand option fail to comply with the performance criteria requirements of federal motor vehicle safety standard no. 121, 'air brake systems.'
  dealers will replace the spring brake modulating valve free of charge. The recall began on october 16, 2006. Owners may contact mack truck at 1-800-528-6586.
  customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 62112 [USA]: This may affect the performance of the steering, which may result in a crash.
  On certain trucks, the bolt that attaches the pitman arm to the steering gear may not be tightened properly.
  dealers will check the torque on the bolt that attaches the pitman arm to steering gear and tighten the bolt properly. The recall beagn august 18, 2005. Owners contact mack at 1-800-2528-6586.
  mack trucks recall no.SC0303. Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236; (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 2007264 [Canada]: Brakes
  On certain vehicles, the internal rubber check valve inside the bendix sr-7 spring brake modulating valve can become deformed over time. The effect of this defect is intermittent and presents a potential delay or failure in applying the parking brakes; potentially resulting in a vehicle roll away. Should this occur, the unattended roll away vehicle could strike a bystander or cause property damage. Correction: dealers will install a check valve repair kit, and replace the parker single check valve.

  Show Content

• Recall 2007265 [Canada]: Brakes
  On certain school and transit buses, the parker single check valve (scv) that connects with the supply port of the bendix sr-7 spring brake modulating valve may become excessively worn and eventually break apart. Pieces of the parker scv can become lodge inside the sr-7 valve, possibly causing either leakage out of the sr-7 valve or preventing air from properly exhausting from the sr-7 valve. This condition can cause a delay in the application of the parking brakes, the spring brakes not fully releasing or loss of isolation between the primary and secondary circuits. These conditions can occur without warning, leading to unintended vehicle rollaway, brake drag, or in case of loss of primary circuit, inability to modulate the spring brakes. An unattended roll away vehicle could strike a bystander or cause property damage. Correction: dealers will replace the single check valve (scv).

  Show Content

• Recall 2007339 [Canada]: Other
  On certain trucks, the fifth wheel hitch assembly's lever arm may have been incorrectly installed during the manufacturing process. The lever arm pivot bolt may have been over-tightened which could distort the pivot bolt spacer sleeve and prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin. This could allow the towed unit to separate from the towing vehicle while underway, potentially causing a crash with injury or death. Correction: dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Air brake system control valves investigation # EA09009

  Investigation has not identified a defect.Complaints have abated.See closing report for further details.
  

  Show Content

• Air brake control valve investigation # PE09010

  Odi is closing this preliminary evaluation and opening an engineering analysis (ea09-009) to further identify and evaluate the vehicle environment and brake system factors that may be causing or contributing to extended stopping distance perfromance in certain vehicles.
  

  Show Content