Mitsubishi Endeavor 2005

• Recall 66895 [USA]: Fuel leakage, in the presence of an ignition source, could result in a fire.
  Mitsubishi is recalling certain model year 2004-2010 endeavor vehicles originally sold in or currently registered in the states of connecticut, delaware, illinois, indiana, iowa, kentucky, maine, maryland, massachusetts, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, virginia, west virginia, wisconsin, and washington d.C. Cold states include north dakota, south dakota, nebraska, kansas, oklahoma, colorado, wyoming, montana, idaho, washington, oregon, and utah. Adjoining states include arkansas, tennessee, and north carolina. In severe corrosive environments where road salts are frequently used in winter vehicles may be exposed to road debris (mud) mixed with road salt. This material can become trapped between a reinforcing bracket and the fuel filler pipe, potentially causing corrosion. Over time, corrosion could create a leak in the fuel filler pipe that could result in a fuel leakage when fueling the vehicle.
  dealers will replace the fuel filler pipe with a new improved part free of charge. The safety recall is expected to begin on or before july 5, 2010. Owners may contact mitsubishi at 1-800-222-0037.
  owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

• Recall 76547 [USA]: Fuel leakage in the presence of an ignition source could result in a fire.
  Mitsubishi is recalling 45,988 my 2005-2007 endeavor, galant, eclipse coupe, and my 2007 eclipse spyder vehicles. The bracket that is the attachment point for the left rear fuel tank mounting strap may have been improperly formed during a metal stamping process. The process may have caused the metal to have a split in the area where the bolt that holds one of the two fuel tank straps to the underside of the vehicle is located. In the event the fuel tank is full and the vehicle is subject to a severe collision, the bracket may break and allow the fuel tank to drop down, possibly causing a fuel leak.
  dealers will inspect to see if the left rear fuel tank strap mounting bracket has splitting beyond a specific limit. Vehicles with moderate to severe splitting will be repaired using a reinforcement cap, a special structural adhesive, and a rivet to reinforce the fuel tank mounting bracket. The recall began on september 20, 2008. Owners may contact mitsubishi at 1-800-222-0037.
  mitsubishi recall no. Sr-08-005.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

• Recall 76087 [USA]: If the driver does not shift to park before removing the key and fails to engage the parking brake, the vehicle could roll and a crash could occur.
  Mitsubishi is recalling 120,000 my 2004-2006 endeavor passenger vehicles. During vehicle use, the ignition key interlock cable (which is a component of the interlock system) may allow the interlocking cam to fall forward and allow the ignition key to be removed from the ignition switch when the gearshift mechanism is not in the park position.
  dealers will inspect and correct these vehicles for the reported condition. The recall will begin on july 7, 2008. Owners may contact mitsubishi at 1-888-648-7820.
  mitsubishi recall no. Sr-08-003.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

• Recall 49958 [USA]: This could cause fracture of the brake caliper and subsequent unexpected partial loss of braking force, which could result in a vehicle crash.
  On certain sport utility vehicles, the material used to manufacture the front disc brake calipers may be brittle due to improper metallurgy.
  dealers will inspect and replace the front brake caliper if necessary free of charge. The recall began on april 10, 2006. Owners may contact mitsubishi at 1-800-222-0037.
  mitsubishi recall no. Sr-06-001.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

• Recall 36166 [USA]: This may result in a partial loss of braking, increased stopping distances, and could lead to a vehicle crash.
  On certain passenger vehicles equipped with anti-lock brakes, the brake master cylinder, which controls the fluid pressure to the vehicle's brakes, may allow brake fluid to bypass internally during stopping.
  dealers will replace the brake master cylinder. The recall began on october 3, 2005. Owners may contact mitsubishi at 1-800-222-0037.
  customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236; (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

• Recall 36578 [USA]: This condition could allow the vehicle to roll if the transmission is not placed into the "park" position and the vehicle is parked on a slope, thus raising the possibility of a crash.
  On certain sport utility vehicles, the parking brake pedal cable lock nut may not have been tightened to the proper torque specification. The lock nut may loosen and come off, which will reduce the effectiveness of the parking brake.
  dealers will inspect and tighten the parking brake cable lock nut, if necessary free of charge. The recall began february 24, 2005. Owners may contact mitsubishi at 1-800-222-5500.
  mitsubishi recall no. Sr-05-001.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

• Recall 2011012 [Canada]: Fuel supply
  Certain vehicles, operated in areas where road salts are frequently used in winter, may be exposed to road debris (mud) mixed with road salt. This material can become trapped between a reinforcing bracket and the fuel filler pipe, potentially causing corrosion. Over time, corrosion could create a leak in the fuel filler pipe that could result in fuel leakage when fueling the vehicle. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: dealers will replace the fuel filler pipe of vehicles equipped with the first-generation version. Vehicles assembled with the second-generation filler pipe will be inspected and, if severe corrosion on the fuel filler pipe is observed, the pipe will be replaced with a third-generation version. For vehicles where corrosion of the fuel filler pipe is not observed, an anti-corrosion wax-like material will be applied to the filler pipe, and the inner wheel well shield will be replaced with an updated part that provides improved protection against mud intrusion and accumulation. ** note: this recall supersedes recall 2010050.**

• Recall 2008100 [Canada]: Other
  On certain vehicles, the ignition key interlock cable may allow the interlocking cam to fall forward and allow the ignition key to be removed from the ignition when the gearshift mechanism is not in the park position. If the driver does not shift to park before removing the key, and fails to engage the parking brake, the vehicle could roll and a crash could occur. This could result in property damage, personal injury or death. Correction: dealers will affect repairs.

• Recall 2008374 [Canada]: Other
  On certain vehicles, the bracket that is the anchor point for the left rear fuel tank mounting strap may have been improperly formed during the manufacturing process. This may have caused the metal to spilt in the area where the bolt holds the fuel strap to the underside of the vehicle. In the event the tank is full of fuel and the vehicle is involved in a serious collision the bracket could break and the tank could drop down. This situation could result in a fuel leak and the possibility of a fire. Correction: dealers will inspect and if necessary install a reinforcement cap to the fuel tank bracket.

• Recall 2006056 [Canada]: Brakes
  On certain vehicles, the metal used to manufacture the front disc brake caliper may be brittle due to improper metallurgy. This could lead to breakage of the brake caliper and subsequent unexpected partial loss of braking force. Unexpected partial loss of braking force could result in a vehicle crash. Correction: dealers will inspect and, if required, replace the front brake calipers.

• Recall 2005047 [Canada]: Brakes
  On certain vehicles, the parking brake pedal cable lock nut may not have been tightened to the proper torque specification during assembly. The lock nut may loosen and come off, which will reduce the effectiveness of the parking brake. This condition could allow the vehicle to roll if the automatic transmission is not placed into the park position. Correction: dealers will tighten the lock nut.

• Recall 2005268 [Canada]: Brakes
  On certain vehicles, the brake master cylinder was improperly assembled which can result in reduced braking pressure and increase brake pedal stroke. Should this condition occur, the braking distance required to stop the vehicle will increase and may lead to a vehicle crash. Correction: dealers will replace the brake master cylinder.

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Ignition-park interlock system investigation as of 20080129

  The subject vehicle ignition-park interlock and shift lock (brake-shift interlock) systems are mechanically actuated.The systems utilize two cable assemblies that connect to a plastic housing mounted to the shift lever mechanism.Within the housing is a lever (interlock lever) that the ignition-park interlock cable connects to.When the interlock lever is positioned in its rearward travel range, the ignition key removal is prevented; when the lever is positioned in its forward position, key removal is allowed.According to mitsubishi, the ignition key interlock cable may allow the interlock lever to fall forward during vehicle use.In this state the ignition key can be removed from the ignition switch when the gearshift mechanism is not in the park position.If the driver does not shift to park before removing the key and fails to engage the parking brake, the vehicle could roll and a crash could occur.Most of the reported crash incidents were minor in nature involving unoccupied vehicles rolling from a parked condition and striking other vehicles or objects.The single injury incident occurred when the operator parked the vehicle, exited, and was subsequently struck by the vehicle as it rolled away.The type and severity of the injuries were not described.In a letter dated march 21, 2008, mitsubishi advised nhtsa that it will conduct a safety recall to address this condition (see www.Safercar.Gov, recall action 08v-139 for further details); remedy details and timing are to be determined.Accordingly the investigation is closed.
  

  Show Content

Common OBD Error codes specific to this vehicle.

• P2100 [1] Throttle Actuator "A" Control Motor Circuit/Open
• P0133 [1] 02 Sensor Circuit Slow Response (Bank 1 Sensor 1)

I was using an exit to merge into the highway and when i merged, the vehicle completely lost power. I could hear the engine working but no power to the vehicle. A semi almost totaled me but thank god it merged thanks to another driver. The rolled barely making it to the side of highway and found out the transmission blew out. I want to make this perfectly clear: i do routine maintenance conducted at professional shops for all oil changes and or other issues religiously and the miles on vehicle aren't high. In other words, i almost lost my life because of this with no working vehicle to add. This incident happened in a busy highway. No acceleration, reverses or anything else other than park. The mechanics told me that this model comes with a cheap filter that allows anomalies such as poorly made material from the suv or others to slowly get in the transmission. As stated before, i regularly keep up maintenance to this vehicle. I don't know how this happened but a good transmission all of a sudden died and i too almost lost my life from a semi doing 75 on a highway.

I was using an exit to merge into the highway and when i merged, the vehicle completely lost power. I could hear the engine working but no power to the vehicle. A semi almost totaled me but thank god it merged thanks to another driver. The rolled barely making it to the side of highway and found out the transmission blew out. I want to make this perfectly clear: i do routine maintenance conducted at professional shops for all oil changes and or other issues religiously and the miles on vehicle aren't high. In other words, i almost lost my life because of this with no working vehicle to add. This incident happened in a busy highway. No acceleration, reverses or anything else other than park. The mechanics told me that this model comes with a cheap filter that allows anomalies such as poorly made material from the suv or others to slowly get in the transmission. As stated before, i regularly keep up maintenance to this vehicle. I don't know how this happened but a good transmission all of a sudden died and i too almost lost my life from a semi doing 75 on a highway.

My vehicle has the same problem as 2006-2008 model years of the same car. That is, the heater controller signal to the hvac system codes as u111, and consequently the a/c will not turn on at all, but indicator light shows it to be on. The compressor is not receiving the signal from the controller. The dealer says this recall (number 10v514000) does not cover 2005 cars.

As i was driving on the highway and and as i sped up the vehicle kept fish tailing it felt like it was the front of the vehicle . So i went straight to my mechanic and he showed me the rust of the rear subframe of the car and it was detached and broken. He suggested i not drive the vehicle because i amy lose co trol of the vehicle.

Tl* the contact owns a 2005 mitsubishi endeavor. The contact stated that extensive mold developed due to a leak in the vehicle. Due to the placement of the air conditioning drain plug, water leaked onto the floorboard. The contact stated that the carpet in the vehicle was soaked. While driving and attempting to depress the brake pedal, the contact's foot slipped off of the brake pedal due to the bottom of her shoe being wet from the leak. The vehicle was taken to several independent mechanics who confirmed that the water leaked from the drain plug. The vehicle was not repaired. A dealer and the manufacturer were not contacted. The approximate failure mileage was 112,000.

The vehicle has a very bad vibration and severe wining sound, not sure what it is but we dont feel safe driving it. New tires , rotors, and breaks were installed and still the same problem. It usually starts vibration at about 25 mph and is hard to maintain a speed.

Wet floor board on drivers side due to a leaking hvac. May cause slippery feet while operating vehicle. Also causing mildew and or rust. Seen lots and lots of discussion on net about this known problem. And they even have a bulletin on there website for the problem. But no recall?

I was pulling into an apartment parking lot at 3 miles per hour or less applied brake and car surged forward. I applied more pressure to brake and the car surged again and would not stop. This caused me to crash into a unoccupied parked car which banged another unoccupied car parked next to it. All 3 cars were damage. My car and the car i hit sustained front end damage. The third car was scraped along the driver side door and rear panel. There was a witness to this accident that told the responding california chp officer that he saw my car experience two surges as i slowly entered the parking. He also informed the office that he saw my break lights on before the first surge happened. Updated 02/24/16*lj updated 12/12/2017*cn

Tl* the contact owns a 2005 mitsubishi endeavor. The contact stated that extensive mold was developing inside of the vehicle due to leak in the interior of the vehicle. The vehicle was taken to an authorized dealer where it was diagnosed that the air conditioning box and tube needed to be cleaned and replaced. The contact was included in nhtsa campaign number: 08v139000 (electrical system). The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 160,000.

Drivers seat belt latch sticks. It takes several times of pressing release button to unlatch the belt. *tr

Tl* the contact owns a 2005 mitsubishi endeavor. The contact stated that the brake warning lamp illuminated. The contact mentioned that the vehicle was consuming excessive brake fluid. The vehicle was taken to the dealer where the technician diagnosed that the brake booster, master cylinder, and wheel cylinders needed to be replaced. The manufacturer was made aware of the failure. The vehicle was not repaired. The failure and current mileage was 40,000.

Drivers side floor soaked, after checking forums sounds like a a/c drain issue. *tr

I was driving along the highway, i smelled what seems to be burning plastic, i saw smoke from under my glove compartment, suddenly my a/c stop working. Upon inspection i notice that the electrical plug to the fan motor looked charred/burnt. I removed it for safety reasons. I read over the internet that is a common problem with these vehicles, the item should be recalled. *tr

My air conditioner keeps going out every year. I have own the vehicle 2 1/2 years. I am having to have the air conditioner fixed again ( that is the summer of 2013, & 2014). I have talked to other owners who are having the same problem. This is costing me around $400.00 every year. I would like someone to investigate and fix this problem. [xxx] information redacted pursuant to the freedom of information act (foia), 5 u.S.C. 552(b)(6). *tr

Tl* the contact owns a 2005 mitsubishi endeavor. The contact stated that while driving 50 mph, he depressed the brake pedal and heard an abnormal grinding noise. The contact exited the vehicle and noticed that the front passenger's side rotor was corroded and had become fractured. The vehicle was not taken to the dealer for inspection or repairs. The manufacturer was notified of the failure. The failure mileage was 100,000.

The rear trunk latch fails to unlock. I cannot open either the glass or the trunk. Have to use the manual release from inside to open. *tr

Air conditioning water drains into the vehicle causing clogging and flooding of the drivers side floor the mileage is only115k. This causes bad odor,growth of microorganisms and could lead to accidents because the floor on the drivers side becomes slippery. Took it to the dealer but they said they have been receiving same complaints. They inspected it for 30 minutes and said looks like the problem has been fixed. Next day after using the air condition for about an hour the floor was flooded again. *tt

I was driving the vehicle home from work when i smelled electrical wire burning through out the car. It was coming from under the glove compartment. I pulled off the road to investigate. The connector to the a/c & heater motor was charred. During internet research i discovered that this is very common occurrence. What people have said on-line was that it was a poor design, thus the connecting pins are too close which causes them to heat up and char the connector. If i would have had a new paper or backpack in that area, it could cause a fire while driving resulting in a fatal accident. I tried reconnecting, that part i used was charred a second time. I believe it should be recalled by the manufacturer. *tr

Tl* the contact owns a 2005 mitsubishi endeavor. The contact stated that the driver side door window dropped and shattered from the interior of the vehicle. The contact mentioned that the door knob was fractured in half. The vehicle was not taken to the dealer and the manufacturer was not made aware of the failure. The vehicle was not repaired. The failure and current mileage was 130,000.

Tl* the contact owns a 2005 mitsubishi endeavor. The contact stated that the exterior door handles fractured from all four doors, as well as the rear hatchback door. The contact spoke with the manufacturer and was told there was no warranty for the door handles. The contact stated that he had to enter the vehicle through the hatch as a result of the failure. The vehicle was not repaired. The failure mileage was unknown and the current mileage was 80,000.

Tl* the contact owns a 2005 mitsubishi endeavor. The contact was driving 10 mph when the brakes were depressed but the vehicle failed to stop. The emergency brake was deployed in order to stop the vehicle. The contact also mentioned the vehicle caliper was detached under the vehicle. The vehicle was taken to a private mechanic where the mechanic confirmed that the caliper and front brakes needed to be replaced. The manufacturer was contacted and they confirmed that the vin did not qualify for repairs under nhtsa campaign id number: 06v068000 (service brakes, hydraulic: foundation components:disc:caliper). The vehicle was repaired. The failure mileage was 80,000 and the current mileage was 82,000.

Tl* the contact owns a 2005 mitsubishi endeavor. The contact was driving 35 mph when the front brake calibers detached forcing an emergency stop. The vehicle was unable to be driven and was towed. The vehicle was serviced by a private mechanic who confirmed the failure. The vehicle was repaired by replacing the calibers and installing new brakes. The manufacturer was contacted who advised that the vin did not qualify for repairs under nhtsa campaign id number: 06v068000 (service brakes, hydraulic:foundation components:disc:caliper). The failure mileage was 130,000 and the current mileage was 131,000.

Air conditioning water recipient clogs causing flooding of the drivers side floor. It is the third time it happens to my mitsubishi endeavor 2005 suv., whose mileage is 55k. This causes bad odor,growth of microorganisms and could lead to accidents because of wet shoes. Additionally, unclogging the water recipient is expensive. *tr

Tl* the contact owns a 2005 mitsubishi endeavor. The contact stated the driver side floorboard was becoming soaked with water. The contact stated that the failure occurred whenever the air conditioner was being operated. The contact took the vehicle to the dealer and the dealer advised that a hose would need to be replaced in order to correct the failure. The hose was not replaced. The failure mileage was 71,250.

While air conditioner is running and vehicle is in motion, blower stops blowing cold air, water drips inside vehicle on passenger side floor gets soaked with water and moldy smell inside vehicle. When making turns, you can hear water sloshing around inside the dashboard, and what sounds like static or sparks behind the dash. Water sometimes run over onto the gas and brake pedals, casing a dangerous situation. Blower motor has since stopped working as a result of water constantly running down on it.

Water leaking into driver side floorboard due to faulty a/c condensation seal at firewall on 2005 mitsubishi endeavor. *tr

Air conditioning drain plug doesn't drain and driver side floor gets very wet causing damaged floor and moldy smell after a while

My son and i was in an accident on may, 20th, 2010 at approximately 3:45 pm. I was driving my 2005 mitsubishi endeavor limited on the interstate at 60 mph. Two cars in front of my vehicle slammed on their brakes to avoiding hitting a motorcyclist that dodged in front of them. I slammed on my brakes and swerved to dodge the van, in front of me, but ending up hitting the van on my front passenger side. I was traveling at approximately 55mph when i hit the van. My 17 year old son's seatbelt failed to work, causing him to hit the windshield, breaking the windshield. After he hit the windshield, his airbag deployed late throwing him up and back. In my opinion, my seatbelt did not work either. My son nor i had any marks on our neck or shoulders, from a seatbelt locking in during an accident. My suv was termed totaled by my insurance company. *tr

While driving at 55mph the power steering failed which caused car to swerve out of lane. The power steering pump part broke internally and was replaced. *tr

Recall on mitsubishi endeavor 2005 electrical system ignition id # 68587 i had to pay for service repair at fox security chevrolet that took over mitsubishi fox security located at 6633 security bld, baltimore, md 21207. *tr

Tl*the contact owns a 2005 mitsubishi endeavor. The contact shifted into park, turned off the vehicle, and removed the keys from the ignition, but the vehicle began to roll backwards. He had to start the ignition while it was rolling and apply the brakes in order to stop the vehicle. The vehicle crashed into another vehicle during the failure. Afterwards, he attempted to place the vehicle into drive, but the vehicle would not move. The vehicle was finally able to move thirty minutes later. The contact took the vehicle to the dealer, but they could not remedy the issue. A police report was filed and there were no injuries. The current mileage was 49,685 and failure mileage was 49,616.

Tl*the contact owns a 2005 mitsubishi endeavor. Whenever the contact attempted to stop the vehicle, the brake pedal would extend to the floor before the vehicle would come to a stop. The vehicle has not been diagnosed by the dealer. The current and failure mileages were 44,000.

Tl*the contact owns a 2005 mitsubishi endeavor. While driving 40 mph, the transmission suddenly locked. Prior to the failure, the contact noticed that the dashboard shift indicator light would flash whenever the vehicle was placed into drive. The vehicle was taken to the dealer and they stated that the transmission needed to be replaced. The current and failure mileages were 70,000.

The airbag did not deploy during the collision which resulted in the total loss of my vehicle. *tr

2005 mitsubishi endeavor, i bought the car brand new, i have had the car for a year. On 12 oct 07, i went to get into my car and it wouldn't start, apparently the weld on the torque converter did not hold. The shop i took it to said that it had to be a defect, especially since the car wasn't that old. *jb

Dt*: the contact stated while parked, it was noticed that water had leaked on the front driver side floor mat. The vehicle had been to the dealer a total of 7 times for the same problem. The air conditioner line was flushed on every visit. Also, an unknown part was ordered and installed on the vehicle, but the problem persisted. Currently, the vehicle had a mold odor, and the driver floormat was flattened because of the water.

2005 mitsubishi endeavor. Had the vehicle for 3 days drove around town in a mild snow and rain. The next day noticed water had leaked into the interior cabin under driver side carpeting. Took two large towels to soak up water. Called dealer. Bringing it to service dept tommorow. I noted there are previous tsb's concerning the problem . *jb

1. My 2005 endeavor has 11,000 kms, covered by the warranty (it has less than a year since i bought it. Lst friday i was driving normally to my work when i felt thumps and if it were pulling back and forth. I don't know how but i managed to park, and when i did something under it ripped off and a huge spot of oil appeared. It leaked all the transmission fluid on the pavement. This could have been lethal if it were on a road, according to the mechanic. Now mitsubishi refuses to recognize warranty. The cause was a broken hose of transmission fluid which caused the leakage. *nm

Dt: the contact stated while purchasing the vehicle he insisted that the dealer convert the driver's seat to a power operated seat. After the power seat was installed the srs light illuminated. The dealer performed diagnostic testing which was inconclusive. The dealer believed it may have been the wiring harness on the power seat that caused the srs light to illuminate. The dealer ordered an air bag to remedy the problem, but it has not been installed. *ak