T-SB-0230-12
Service Bulletin Details
Public Details for: T-SB-0230-12
Summary to be provided on a future date.
- 2009 - 2008 - 2007 - 2006 - 2005 -
Models from 2009
2009 TOYOTA 4RUNNER |
Models from 2008
2008 TOYOTA 4RUNNER |
Models from 2006
2006 TOYOTA 4RUNNER |
2006 TOYOTA LAND CRUISER |
2006 TOYOTA SEQUOIA |
2006 TOYOTA TUNDRA |
Models from 2005
2005 TOYOTA 4RUNNER |
2005 TOYOTA SEQUOIA |
2005 TOYOTA TUNDRA |
@TOYOTA T-SB-0230-12 Rev1 November 27, 2012 Technical Service Bulletin Air Injection System MIL "ON" Service Category Engine/Hybrid System Section Engine Control Market USA Toyota Supports ~ ASE Certification W, Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 4Runner VDS(s) : BT14R, BT17R, ZT14R, ZT17R 2006 - 2007 Land Cruiser 2005 - 2007 Sequoia VDS(s): BT44A, BT48A, ZT34A, ZT38A 2005 - 2006 Tundra VDS(s) : BT441, BT481 , DT441 , DT481, ET341 , ET381,JT321, KT421 , RT341, RT381 REVISION NOTICE October 17, 2013 Rev1: • The entire bulletin has been updated to include OTC P2445 and diagnosis of the Air Injection Control Driver. • Applicability has been updated to include 2006 - 2007 model year Land Cruiser vehicles. • Parts Information has been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. EG027-07. • Information from EG027-07 has been combined with T-SB-0230-12. Service Bulletin No. EG027-07 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. © 2013 Toyota Motor Sales, USA Page 1 of 8 @TOYOTA T-SB-0230-12 Rev1 November 27, 2012 Page 2 of 8 Air Injection System MIL "ON" Introduction Some 2005 - 2009 model year 4Runner, 2006 - 2007 model year Land Cruiser, 2005 - 2007 model year Sequoia , and 2005 - 2006 model year Tundra vehicles equipped with the 2UZ-FE (4.7 L) engine may exhibit a MIL "ON" condition for the following Diagnostic Trouble Codes (DTCs): • P0412 - Secondary Air Injection System Switching Valve "A" Circuit • P0418 - Secondary Air Injection System Relay "A" Circuit • P1440/P1443 - Secondary Air Injection System Control Valve Circuit Bank 1 I Bank 2 • P1441/P1444 - Secondary Air Injection System Switching Valve No. 2 Bank 1 I Bank 2 Stuck Open • P2440 - Secondary Air Injection System Switching Valve Stuck Open Bank 1 • P1442/P1445 - Secondary Air Injection System Switching Valve No. 2 Bank 1 I Bank 2 Stuck Close • P2441 - Secondary Air Injection System Switching Valve Stuck Close Bank 1 • P2445 - Secondary Air Injection System Pump Stuck Off Bank 1 This condition may be caused by debris passing through the air injection pump assembly and contaminating various components in the system. Use the following procedure to address this condition . Parts Information PART NUMBER PART NAME QTY 17600-0FO 10 Pump Assembly, Air 1 17171-50030 Gasket, Intake Manifold to Head No. 1 2 PREVIOUS NEW 25710-50020 25710-50021 25710-50022 Valve Assy, Air Switching 1* 25720-50010 25720-50011 Valve Assy, Air Switching, No. 1 1* 25720-50020 Valve Assy, Air Switching , No. 2 1* 17377-50010 Gasket, Air Tube 4** Driver, Air Injection Control 1 89580-34010 89580-34011 89581-34040 89581-34041 89581-71010 89580-34012 * Replace ONLY If damaged by debris. Reuse parts when possible. ** 2 per valve. © 2013 Toyota Motor Sales, USA @TOYOTA Rev1 T-SB-0230-12 Page 3 of 8 November 27, 2012 Air Injection System MIL "ON" Warranty Information MODEL TIME 4Runner 1.6 DESCRIPTION OP CODE OFP T1 T2 17600-0F010 8A 99 Land Cruiser R & R Air Pump Assy EG1215 Sequoia 2.2 Tundra Combo A R & R Valve Assy, Air Switching* +0 .3 Combo B R & R Valve Assy, Air Switching, No. 1 and/or No. 2* All Combo C R & R Air Injection Control Driver All +0.5 +0.5 * Replace ONLY If damaged by debris. Reuse parts when possible. APPLICABLE WARRANTY • This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. • For California specification vehicles sold and operated in California, Connecticut (starting with '08 MY}, Maine, Massachusetts, New Jersey (starting with '09 MY}, Oregon (starting with '09 MY}, Pennsylvania (starting with '08 MY}, Rhode Island (starting with '08 MY}, Vermont, and Washington (starting with '09 MY}, this repair is covered under the California Emission Warranty, which is 84 months or 70,000 miles, whichever occurs first, from the vehicle's in-service date. • Warranty application is limited to occurrence of the specified condition described in this bulletin. Required Tools & Equipment REQUIRED EQUIPMENT SUPPLIER QTY TS2UNIT Techstream 2.0* TIS Techstream PART NUMBER ADE Techstream Lite TSPKG1 TSLITEDLR01 * Essential SST. NOTE • Only ONE of the Techstream units listed above is required. • Software version 8.20.019 or later is required. • Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at 1-800-368-6787. © 2013 Toyota Motor Sales, USA 1 @TOYOTA T-SB-0230-12 Rev1 November 27, 2012 Page 4 of 8 Air Injection System MIL "ON" Repair Procedure 1. Using Techstream , check if DTCs P0412, P0418, P1440/P1443, P1441/P1444, P1442/P1445, P2440, P2441 , or P2445 are present. If OTC is present, refer to the Technical Information System (TIS), applicable model and model year Repair Manual : 4Runner: • 2005 4Runner: Engine/Hybrid System- Engine Control- "SF/ System (2UZ-FE): P0412 Secondary Air Injection System Switching Valve "A" Circuit" • 2006 I 2007 I 2008 I 2009 4Runner: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P0412; Secondary Air Injection System Switching Valve "A" Circuit" • 2005 4Runner: Engine/Hybrid System - Engine Control- "SF/ System (2UZ-FE) : P0418 Air Injection System Relay ''A" Circuit" • 2006 I 2007 I 2008 I 2009 4Runner: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P0418; Secondary Air Injection System Control ''A " Circuit" • 2005 4Runner: Engine/Hybrid System- Engine Control- "SF/ System (2UZ-FE) : P1440, P1443 Secondary Air Injection System Control Valve Circuit Bank 2" • 2006 I 2007 I 2008 I 2009 4Runner: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P1440, P1443; Secondary Air Injection Vacuum Switching Valve Circuit Malfunction Bank 1" • 2005 4Runner: Engine/Hybrid System - Engine Control- "SF/ System (2UZ-FE) : P1441, P1444, P2440 Secondary Air Injection System Switching Valve Stuck Open Bank 1" • 2006 I 2007 I 2008 I 2009 4Runner: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P1441, P1444, P2440; Stuck Open in Secondary Air Injection Vacuum Switching Valve Bank 1" · • 2005 4Runner: Engine/Hybrid System - Engine Control - "SF/ System (2UZ-FE): P1442, P1445, P2441 Secondary Air Injection System Switching Valve Stuck Open Bank 1" • 2006 I 2007 I 2008 I 2009 4Runner: Engine/Hybrid System- Engine Control- "2UZ-FE Engine Control System: SF/ System: P1442, P1445, P2441; Stuck Close in Secondary Air Injection Vacuum Switching Valve Bank 1" © 2013 Toyota Motor Sales, USA @TOYOTA T-SB-0230-12 Rev1 November 27, 2012 Page 5 of 8 Air Injection System MIL "ON" Repair Procedure (Continued) • 2005 4Runner: Engine/Hybrid System - Engine Control- "SF/ System (2UZ-FE): P2445 Secondary Air Injection System Pump Stuck Off Bank 1" • 2006 I 2007 I 2008 I 2009 4Runner: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P2445; Secondary Air Injection System Pump Stuck On Bank 1" Land Cruiser: • 2006 I 2007 Land Cruiser: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P0412; Secondary Air Injection System Switching Valve '~"Circuit" • 2006 I 2007 Land Cruiser: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P0418; Secondary Air Injection System Control'~" Circuit" • 2006 I 2007 Land Cruiser: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P1440, P1443; Secondary Air Injection Vacuum Switching Valve Circuit Malfunction Bank 1" • 2006 I 2007 Land Cruiser: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P1441, P1444, P2440; Stuck Open in Secondary Air Injection Vacuum Switching Valve Bank 1" • 2006 I 2007 Land Cruiser: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P1442, P1445, P2441; Stuck Close in Secondary Air Injection Vacuum Switching Valve Bank 1" • 2006 I 2007 Land Cruiser: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P2445; Secondary Air Injection System Pump Stuck On Bank 1" Sequoia: • 2005 Sequoia : Engine/Hybrid System - Engine Control- "Engine: P0412 Secondary Air Injection System Air Switching Valve "A" Circuit" • 2006 I 2007 Sequoia: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P0412; Secondary Air Injection System Switching Valve '~"Circuit" © 2013 Toyota Motor Sales, USA @TOYOTA T-SB-0230-12 Rev1 November 27, 2012 Page 6 of 8 Air Injection System MIL "ON" Repair Procedure (Continued) • 2005 Sequoia: Engine/Hybrid System- Engine Control- "Engine: P0418 Air Injection System Air Pump Malfunction " • 2006 I 2007 Sequoia: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P0418; Secondary Air Injection System Control "A" Circuit" • 2005 Sequoia: Engine/Hybrid System - Engine Control- "Engine: P1440, P1443 Secondary Air Injection System Control Valve Circuit Bank 2" • 2006 I 2007 Sequoia: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P1440, P1443; Secondary Air Injection Vacuum Switching Valve Circuit Malfunction Bank 1" • 2005 Sequoia: Engine/Hybrid System- Engine Control- "Engine: P1441, P1444, P2440 Secondary Air Injection System Switching Valve Stuck Open Bank 1" • 2006 I 2007 Sequoia: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P1441, P1444, P2440; Secondary Air Injection Vacuum Switching Valve Circuit Malfunction Bank 1" • 2005 Sequoia: Engine/Hybrid System - Engine Control - "Engine: P2445 Secondary Air Injection System Pump Stuck On Bank 1" • 2006 I 2007 Sequoia: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P2445; Secondary Air Injection System Pump Stuck On Bank 1" Tundra: • 2005 Tundra: Engine/Hybrid System- Engine Control- "Engine (2UZ-FE) : P0412 Secondary Air Injection System Air Switching Valve "A" Circuit" • 2006 Tundra: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P0412; Secondary Air Injection System Switching Valve "A" Circuit" • 2005 Tundra: Engine/Hybrid System - Engine Control- "Engine (2UZ-FE) : P0418 Air Injection System Air Pump Malfunction" • 2006 Tundra: Engine/Hybrid System - Engine Control- "2UZ-FE Engine Control System: SF/ System: P0418; Secondary Air Injection System Control ''.A" Circuit" © 2013 Toyota Motor Sales, USA @TOYOTA T-SB-0230-12 Rev1 November 27, 2012 Page 7 of 8 Air Injection System MIL "ON" Repair Procedure (Continued) • 2005 Tundra : Engine/Hybrid System - Engine Control- "Engine (2UZ-FE) : P1440, P1443 Secondary Air Injection System Control Valve Circuit Bank 2" • 2006 Tundra : Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P1440, P1443; Secondary Air Injection Vacuum Switching Valve Circuit Malfunction Bank 1" • 2005 Tundra : Engine/Hybrid System - Engine Control - "Engine (2UZ-FE) : P1441, P1444, P2440 Secondary Air Injection System Switching Valve No. 2 Stuck Open Bank 1" • 2006 Tundra: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P1441, P1444, P2440; Secondary Air Injection Vacuum Switching Valve Circuit Malfunction Bank 1" • 2005 Tundra : Engine/Hybrid System - Engine Control - "Engine (2UZ-FE): P1442, P1445, P2441 Secondary Air Injection System Switching Valve Stuck Close Bank 1" • 2006 Tundra: Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P1442, P1445, P2441; Stuck Close in Secondary Air Injection Vacuum Switching Valve Bank 1" • 2005 Tundra: Engine/Hybrid System - Engine Control- "Engine (2UZ-FE): P2445 Secondary Air Injection System Pump Stuck Off Bank 1" • 2006 Tundra : Engine/Hybrid System - Engine Control - "2UZ-FE Engine Control System: SF/ System: P2445 Secondary Air Injection System Pump Stuck On Bank 1" 2. After repair, if any DTCs are displayed at this time, clear the DTC(s) and click Data List. 3. Select All Data. 4. Display the following parameters: • Secondary Air Control VSV • 2nd Air System Status • MIL © 2013 Toyota Motor Sales , USA @TOYOTA Rev1 T-SB-0230-12 November 27, 2012 Page 8 of 8 Air Injection System MIL "ON" Repair Procedure (Continued) 5. Start the engine and wait for air pump operation. • Secondary Air Control VSV • 2nd Air System Status = ON = ON NOTE If Secondary Air Control VSV and 2nd Air System Status do not change to "ON," perform again after engine cools. - • If MIL illuminates, or a OTC is detected, proceed to step 6. • If MIL does not illuminate, or a DTC is not detected, proceed to step 8. 6. Using Techstream , check for DTCs. If P0418 and/or P2445 are present, replace the Air Injection Control Driver. Figure 1. 1 I Air Injection Control Driver 2 Specified Torque: 7.5 N*m (76 kgrcm, 66 in*lbf) 7. If physical inspection is required through the Repair Manual diagnostic process, look for debris that may have contaminated the air injection system. The debris may consist of air injection pump filter material or fan blade fragments. 8. If such debris is found , replace the air injection pump. If not, go to step 10. 9. Additionally, determine if the debris can be removed from any secondarily affected parts and confirm they operate properly. If they do not operate properly, part replacement is required . 10. Clear the DTCs and road test the vehicle to confirm the condition has been corrected. © 2013 Toyota Motor Sales, USA ®TOYOTA PRIUS PHV 2014 PRE-DELIVERY SERVICE CHECK SHEET ~1u BEFORE INSPECTION 01 Install Short Pin (see page 2) .............. .. ........ .... ..... ....... 02 Install radio antenna* .... .... .... ............ ......... . .......... ......... D D FUNCTIONAL OPERATION Apply parking brake and cycle ignition "IG-ON';· place gear selector in reverse, tum on lights and rear defogger. Unlock doors; release fuel door. and release the back door. 01 02 03 04 05 06 07 08 09 10 11 Check dome, courtesy, map, and sun visor lights* ...... ... Check warning/indicator lights, gauges, and horn .......... Check windshield wipers and washers .......... ...... .. ...... .... Check headlights, instrument lights, turn signals, emergency flashers , and brake lights ....................... ..... Check inside/outside rear view mirror operation/adjustment Check cigarette lighter* and power outlets .. ...... .. .. .... ...... Check audio/navigation*/backup camera* systems and set clock ... .. ..... ..... ... .... ... .... ... .... .... ..... ... .... ... ... . ....... . Verify Entune/Navigation software version (Display Audio, Non-HOD Type only)* .... .. .. .... .... .. .. .. .. .. .. ...... .... . Check multi-information display and trip information on center display• .. .. ...... ...... .. .... .... ... ... ...... .... ...... .... .. ..... .. Install shift-lock override button cover* .... .... .. ......... ...... .. Check sliding roof* .... .. .......................................... .. ....... DD DD DD DD DD DD DD DD DD DD DD 05 06 07 08 09 10 11 Check engine oil level .. .... .... ···· ··· ····· ···· ···· ···· ······ ·· ··········· Check brake fluid level .................. .. .... ...... .. ..... .... ......... ... Check engine coolant level ...... ...... ........... .. .. ..... .... .. ..... ... Check inverter coolant level .... .. ...... .. ...... .... .... ...... ... .... .. . Check windshield washer fluid level ...... ...... .. .... .. ............ Inspect for fuel , oil , coolant, and other fluid leaks ... ...... .. D DD DD D D D DD DD DD D DD Enter Odometer Readings Reading Before Test: 01 02 03 04 05 06 07 08 09 10 11 DD DD DD DD DD DD DD DD DD DD Reading After Test: Check cold engine operation . . . . . .. . . . . . . . . . . .. . . . . . .. .. . . . . . ... ...... Check engine operation during warm-up .. .. ..................... Check engine at normal operating temperature ........ .. .... Check hybrid transaxle operation .............. .. ... .... . .......... Check brake and parking brake operation ...... .. .... ........... Check steering operation & off-center/vehicle pull/flutter. Inspect for abnormal noise and vibration ......... . ... .... .. ..... Inspect for squeaks and rattles .............. ················· ···· ·· ·· Check heater and A/C* operation . .. .... ... .......... .. ...... ....... Check cruise control operation* .. ... .. ....... .. ..................... .. Check front seat heater operation* ...................... ...... ..... DD DD DD DD DD DD DD DD DD DD DD FINAL INSPECTION AND CLEANING 01 Remove interior protective covers, unnecessary labels, tags, etc. (Remove protective covers just before delivery to customer) .. .. .... ....... .. ...... ........ .... .... .... .... ........ .... .. .. ... . 02 Visually inspect all interior parts for installation , damage , fit, dirt, etc......... .. .................. .. ...... .. ........ ... .... ................. 03 Verify floor mat application and install using retaining clips* ............................................................... 04 Verify green light is illuminated on SOS (Safety Connect) button* ... .... ........ .... ...... ...... ..... .... ... ......... ........ 05 Remove Rapgard™ and clear protective bumper film* .. .. 06 Wash and clean vehicle ................ .... ............ .. ...... .. ........ 07 Inspect paint finish for scratches, chips, rust, dents, damage, etc .. ......... ....................... .... .... .. .. .. .... ..... .. .......... 08 Place oil change sticker on inside of windshield , top left corner .. .. .. ........................ ....... ............... . . ......... .. .. 09 Inspect exterior body parts for proper installation , damage, rust, etc ........... .. ........ .... ........ ...... ..... ... . ... ....... 10 Install front license plate and mounting bracket* (see page 2) .... ... ............................. ...... .. .... ..... .. .................... 11 Place Owner's Guide & first aid kit portfolio* in glove box 12 Perform Techstream Health Check .. ...... .... .... .... .... .. ..... . DD UNDER HOOD 01 02 03 04 05 06 ~lit ::i .. 01 Remove disc brake anti-rust covers/anti-corrosion wheel film* .................................................................... .. 02 Inspect tires for defects/damage .... .. .. .. ......... ........ . ....... 03 Activate and Initialize Tire Pressure Warning System (TPWS) (see page 2) .. .. .................................... .. ........ .. .. 04 Install wheel caps* ...................................... ... ... ..... ....... . 05 Install front spoiler under cover & rear side spoilers 06 Install rear wheel opening extension pads ................ 07 Inspect for fuel , oil, coolant, and other fluid leaks .... ...... .. 08 Inspect under the vehicle for damage , rust, etc ... ..... ...... 09 Visually check bolts and nuts on chassis and powertrain for looseness .... ... ...... ... .... .... .. ... .... ....... ... ... ..... ...... ....... 10 Install rubber body plugs (stored in glove box or console)* . 11 Check hybrid transaxle fluid ... ..... .. ......... .... ... ... .............. ROAD TEST Start at left front door. Check windo w and door lock operation (from master power switch, if equipped). Continue around vehicle in a counterclockwise direction checking each door and window operation, child door locks, seat belts, interior condition, all lights, luggage compartment contents. Finish by checking headlight aim and continue into UNDER HOOD checks. Check Smart Key System ............................................. Check window operation ........... ························ ············· Check that engine starts with all keys ........... .. ......... ........ Check that child safety door locks are in normal (unlocked) position* ... .. ........................ ........................... Check seats and seat belt operation ................................ Check rear defogger/rear view mirror defogger* .. .... .... .. .. Check side marker, tail , backup, and license plate lights Check luggage compartment light* and trim appearance Check emergency tire puncture repa ir kit ...... .. ...... .. ...... Check headlight aim ..................... .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Check battery state-of-charge using Digital Battery System Analyzer (SOC Reading: _ _%)* ................. UNDER VEHICLE (ON HOIST) A complete road test helps assure customer satisfaction. Drive vehicle over a variety of road sur.faces and driving conditions. Check for unusual noise and driving per.formance. WALKAROUND INSPECTION 01 02 03 04 October 2013 DD DD DD DD DD DD BATIERY MAINTENANCE ............. DD DD 01 Perform HV battery check and maintenance 02 Perform Plug-In charge check .................................... * Inspect or install when equipped/required. D DD DD DD D D DD D DD D D DD Completion and retention of this from is required to comply with Toyota's Warranty Policy. TECHNICIAN'S SIGNATURE NAME (PLEASE PRINT) Date Dealer Name I We hereby certify that all items on this form have been checked and corrected for proper operation as required. SERVICE MANAGER'S SIGNATURE I NAME (PLEASE PRINT) Dealer Code I Vehicle Identification Number (Sticker) SHORT PIN INSTALLATION To minimize battery discharge the Short Pin has been removed and is stored in the engine compartment Relay Block. Install the Short Pin and confirm all related DTCs are cleared. OTC Clearing Procedure 1. Connect Techstream to DLC3. 2. Cycle the ignition switch to the "IG-ON" position. 3. Using Techstream, check any other codes being output. 4. Erase DTCs (81650, 81794, U0155, U0142, and U0100) and Freeze Frame Data . NOTE If any DTCs besides 81650, 81794, U155 , U0142, and U0100 remain , repair the applicable system according to the Repair Manual. 1 Storage Location 2 Installation Location TPWS ACTIVATION AND INITIALIZATION Activation Procedure 1. Connect Techstream to DLC3 . 2. Cycle the IG switch to the "IG-ON" position and check that the Low Tire Pressure Warning Light blinks for 1 minute and then remains illuminated. 3. Press or remove the valve core to reduce the tire inflation pressure rapidly by 6 psi (0.4 kgf/cm 2 , 40 kPA), or more, within 30 seconds. 4. Using Techstream , check for DTCs (C2111-C2114) . If no DTCs are stored, continue to step 5. If these DTCs are stored, repeat step 3. 5. Adjust all tires to the standard tire inflation pressure, as indicated on the Tire and Loading information label inside the driver's door jamb. 6. Check the tire pressure values of all the tires using Techstream . TPWS ECU I DATA LIST I TIREPRESS 1-4 NOTE If DTCs C2111-C2114 are present after repeating step 3, lift the vehicle and rotate each tire so that the tire pressure warning valve/sensor is at the top of the wheel well. Then repeat step 3. Initialization Procedure Refer to the Repair Manual for the Initialization procedure . NOTE To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature , perform a Health Check using Techstream and select the "Compensation Tire Pressure" checkbox. Compensation pressures will be displayed on the Health Check results screen . Adjust the tire pressure when the tires are cold . FRONT LICENSE PLATE AND MOUNTING BRACKET INSTALLATION 1. Align holes "A" of the mounting bracket with the dimples on the front bumper cover. Mark the location of holes "B" in the front bumper cover. A NOTE • Holes "A" are used for installation of the mounting bracket to the bumper cover. • Holes "B" are used for installation of the front license plate to the mounting bracket. 2. Drill 2 relief holes with a diameter of 11 mm (0.43 in.) at the hole "B" marks on the front bumper cover to prevent the license plate retaining bolt from contacting the cover. 3. Install the mounting bracket to the front bumper cover by attaching the 2 self-tapping screws into the dimples. 4. Install the front license plate to the mounting bracket using bolts with the following dimensions. Length: 20.0 - 25.0 mm (0.79- 0.98 in.) Diameter: 6.0 mm (0.24 in.) Pitch: 1.0 mm (0.04 in.) NOTICE • Do NOT pre-drill holes into the bumper. • Do NOT overtighten the self-tapping screws. 1 Mounting Bracket 2 Mark and Dril I Holes 3 Dimples