V461703 2015173
Service Bulletin Details
Public Details for: V461703 2015173
Updated to include additional models and model year applicability.
- 2018 - 2017 - 2016 - 2015 - 2014 -
Models from 2018
Models from 2017
Models from 2016
Models from 2015
Models from 2014
Technical Bulletin Model(s) Year Eng. Code Trans. Code VIN Range From VIN Range To 2014-2018 All All All All All (except Routan) Condition 46 17 03 November 21, 2017 2015173 Supersedes Technical Bulletin 46-16-07 (V461607) dated August 23, 2016 to include model year 2018 applicability. Brake Disc Pulsation or Vibration (U.S. Only) When applying brakes at highway speeds the following symptoms may occur: Brake pedal pulsation Vibration felt in vehicle body Steering wheel shakes Technical Background For brake vibration or pulsation concerns, brake disc machining is allowed between 6 and 12 months or 6,000 and 12,000 miles (whichever comes first) from the warranty in service date. Production Solution No production change required. Service Note: All policies and procedures outlined in this technical bulletin also apply to sublet brake disc machining. Improperly machined brake discs may cause brake pulsation/vibration after several months in service. The servicing facility will be responsible for these failures. Page 1 of 12 © 2017 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Bulletin Procedure: Remove wheels and separate brake calipers from carrier as outlined in Repair Manual Group 44 – Wheels, Tires, Vehicle Alignment and Group 46 – Brakes – Mechanical components in Elsa. Brake Disc Inspection A detailed brake disc inspection is needed to determine if the brake disc should be machined or replaced. Inspect brake disc friction surfaces on both sides of the brake disc for: Severe discoloration (bluing) High heat surface damage (raised hard spots) Visible cracks Brake discs showing any of the above described conditions are NOT serviceable. Parts must be replaced in accordance with the Volkswagen Warranty Policy and Procedure Manual. Disc Thickness Measuring Technician must record the beginning thickness measurements on the back of the repair order. Each brake disc has the minimum allowed thickness cast, stamped or laseretched into the disc hub. Measure the brake disc thickness in 4 locations using either the Pro Cut International™ disc thickness measuring tool Part No. 50-902 or the Hunter Engineering Company disc thickness measuring tool Part No. 2599-2. Measurements MUST be taken at the same distance from the brake disc outer circumference to ensure consistency. Page 2 of 12 © 2017 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Bulletin Note: The brake disc thickness measurement must exceed the minimum specification after the machining process is completed in order to be re-used. If the brake disc thickness measurement does not meet this requirement, then replace the brake disc. Brake Disc Machining Note: All brake discs must be machined. Recommended on-car brake lathes are either the PRO-CUT International ™ PFM 9.0, or the Hunter Engineering Company model OCL 400. This design of brake lathe will produce a surface quality which will provide proper brake performance without a brake pad to brake disc break-in period. To ensure that a high quality brake disc finish is produced, brake lathe cutting tools must be maintained as directed by the lathe or tool manufacturer. Page 3 of 12 © 2017 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Bulletin Follow the brake lathe manufacturer’s instructions for set-up and machining. Wash the brake disc with a soap and water solution upon completion of resurfacing to remove all machining particles. Technician must record the final thickness measurements on the back of the repair order. Re-measure brake disc thickness in 4 locations using either the Pro Cut International™ disc thickness measuring tool Part No. 50-902 or the Hunter Engineering Company disc thickness measuring tool Part No. 2599-2. If recorded brake disc measurement is less than the minimum thickness, the brake disc MUST be replaced. Note: Always replace brake discs in pairs (front axle or rear axle). Do not replace all 4 brake discs unless it is required. Page 4 of 12 © 2017 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Bulletin Measure brake disc lateral run out using Pro Cut Disc Lateral run out measuring kit Part No. 50-700FC or the Hunter Disc Lateral run out measuring kit Part No. 25-128-2 with a dial indicator. Run out must not exceed 0.1mm. If brake disc exceed the 0.1mm specification replace the applicable brake discs. Page 5 of 12 © 2017 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Bulletin Warranty To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and Procedures Manual 1) Model(s) Year(s) Eng. Code(s) Trans. Code(s) VIN Range From VIN Range To 2014-2018 All All All All All (except Routan) Claim Type: Use applicable Claim Type 1) SAGA Coding Damage Location Damage Service Number HST (Depends on Service No.) -- Use applicable when indicated in Elsa (L/R) Code 4650 0013 WWO 2) Passat/CC/Tiguan/Eos/ Touareg/Golf R/e Golf and MY14 Golf/Atlas Parts Manufacturer 3ME 2) Jetta/Beetle/Beetle Cabrio, MY14 Jetta SportWagen and MY15-18 Golf/Golf SportWagen/Alltrack/Tiguan LWB On Car Lathe is available (All vehicles) Labor Operation 3): Remove and Reinstall Front and Rear Wheels Labor Operation 3): Front and Rear Disc Resurfacing – On Vehicle 44052004 = 50 TU 46504699 = 120 TU And 46534699 = 120 TU Page 6 of 12 © 2017 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Bulletin Or If On Car Lathe is unavailable: CC/Tiguan/Eos Labor Operation 3): Remove and Reinstall Front and Rear Wheels 44052004 = 50 TU 46142050 = 90 TU Labor Operation 3): Remove and Reinstall Front and Rear Carriers And 46152050 = 90 TU 46502050 = 10 TU Labor Operation 3): Remove and Reinstall Front and Rear Discs And 46532050 = 10 TU 46504699 = 160 TU Labor Operation 3): Front and Rear Discs Machining And 46534699 = 160 TU OR Tiguan LWB Labor Operation 3): Remove and Reinstall Front and Rear Wheels 44052004 = 50 TU 46142050 = 80 TU Labor Operation 3): Remove and Reinstall Front and Rear Carriers And 46152050 = 80 TU 46502050 = 10 TU Labor Operation 3): Remove and Reinstall Front and Rear Discs And 46532050 = 10 TU 46504699 = 160 TU Labor Operation 3): Front and Rear Discs Machining And 46534699 = 160 TU Page 7 of 12 © 2017 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Bulletin OR Atlas Labor Operation 3): Remove and Reinstall Front and Rear Wheels 44052004 = 50 TU 46142050 = 80 TU Labor Operation 3): Remove and Reinstall Front and Rear Carriers And 46152050 = 80 TU 46502050 = 10 TU Labor Operation 3): Remove and Reinstall Front and Rear Discs And 46532050 = 10 TU 46504699 = 160 TU Labor Operation 3): Front and Rear Discs Machining And 46534699 = 160 TU Or Passat Labor Operation 3): Remove and Reinstall Front and Rear Wheels 44052004 = 50 TU 46502050 = 70 TU Labor Operation 3): Remove and Reinstall Front and Rear Discs And 46532050 = 70 TU 46504699 = 160 TU Labor Operation 3): Front and Rear Discs Machining And 46534699 = 160 TU Or Jetta/Beetle/Beetle Carbio and MY14 Jetta SportWagen Labor Operation 3): Remove and Reinstall Front and Rear Wheels 44052004 = 50 TU Page 8 of 12 © 2017 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Bulletin Labor Operation 3): Remove and Reinstall Front and Rear Brake Carriers 46142050 = 90 TU And 46152050 = 90 TU 46502050 = 10 TU Labor Operation 3): Remove and Reinstall Front and Rear Discs And 46532050 = 10 TU 46504699 = 160 TU Labor Operation 3): Front and Rear Discs Machining And 46534699 = 160 TU Or Touareg Labor Operation 3): Remove and Reinstall Front and Rear Wheels 44052004 = 50 TU 46502050 = 110 TU Labor Operation 3): Remove and Reinstall Front and Rear Discs And 46532050 = 90 TU 46504699 = 160 TU Labor Operation 3): Front and Rear Discs Machining And 46534699 = 160 TU Or MY15-18 Golf SportWagen, Alltrack Labor Operation 3): Remove and Reinstall Front and Rear Wheels 44052004 = 50 TU Labor Operation 3): Remove and Reinstall Front Carrier 46142050 = 80 TU 46502050 = 10 TU Labor Operation 3): Remove and Reinstall Front and Rear Discs And 46532050 = 90 TU (includes carrier) Page 9 of 12 © 2017 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Bulletin 46504699 = 160 TU Labor Operation 3): Front and Rear Discs Machining And 46534699 = 160 TU Or MY14 Golf Labor Operation 3): Remove and Reinstall Front and Rear Wheels 44052004 = 50 TU 46142050 = 90 TU Labor Operation 3): Remove and Reinstall Front and Rear Carrier And 46152050 = 80 TU 46502050 = 10 TU Labor Operation 3): Remove and Reinstall Front and Rear Discs And 46532050 = 10 TU 46504699 = 160 TU Labor Operation 3): Front and Rear Discs Machining And 46534699 = 160 TU Or MY15-18 Golf/Golf R/eGolf Labor Operation 3): Remove and Reinstall Front and Rear Wheels 44052004 = 50 TU Labor Operation 3): Remove and Reinstall Front Carrier 46142050 = 80 TU 46502050 = 10 TU Labor Operation 3): Remove and Reinstall Front and Rear Discs And 46532050 = 90 TU (carrier included) 46504699 = 160 TU Labor Operation 3): Front and Rear Discs Machining And 46534699 = 160 TU Page 10 of 12 © 2017 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Bulletin Outside Labor: Sublet Machining Sublet Machining not to exceed Elsa SRT Causal Part: Select Labor Diagnostic Time 4) GFF Time expenditure 01500000 = 00 TU max. NO Road Test 01210002 = 10 TU YES 01210004 = 10 TU Technical Diagnosis 01320000 = 00 TU max. NO Claim Comment: Input “As per Technical Bulletin 2015173” in comment section of Warranty Claim. 1) Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only 2) Code per warranty vendor code policy. 3) Labor Time Units (TUs) are subject to change with Elsa updates. 4) Documentation required per Warranty Policy Procedures Manual. Required Parts and Tools No Special Parts required. Description Part No: Quantity Pro Cut ™ Disc Thickness Measuring Tool 50-902 1 Hunter Disc Thickness Measuring Tool 25-99-2 1 Pro Cut Disc Lateral Run out Measuring Tool 50-700FC 1 Hunter Disc Lateral Run out Measuring Tool 25-128-2 1 PRO-CUT International ™PFM 9.0 PCIPFM90VW 1 Hunter Engineering Company Model OCL 400 HUNOCL400VW 1 Page 11 of 12 © 2017 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Bulletin Additional Information All part and service references provided in this Technical Bulletin are subject to change and/or removal. Always check with your Parts Dept. and Repair Manuals for the latest information. Document Control Revision Table Instance Number Published Date Version Number Reason For Update 2015173/25 11/21/2017 V461703 To include model year 2018 applicability. 2015173/24 8/23/16 V461607 To include model year 2017 applicability. 2015173/23 5/4/16 V461605 Update warranty labor operation for Jetta, Beetle, Beetle Convertible and Jetta SportWagen. 2015173/1 6/11/07 V460701 Original publication. Page 12 of 12 © 2017 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.