NTB19-004

Classification:
Reference:
EL18-035
Date:
NTB19-004
January 17, 2019
2015-2019 MURANO AND 2016-2019 TITAN;
CLIMATE CONTROLLED SEAT INOPERATIVE
APPLIED VEHICLES:
APPLIED SYSTEM:
2015-2019 Murano (Z52)
2016-2019 Titan (A61)
Climate Controlled Seats Only
IF YOU CONFIRM
The driver or passenger side climate controlled seat:

Heating and cooling features do not operate
And

The harness connector or control unit of the climate controlled seat appears as
shown in Figure 3 or Figure 5.
ACTION
Perform the following to the affected seat:
A. Replace the climate controlled seat control unit.
B. Drill a hole for the new harness clip.
C. Replace the harness connector of the climate controlled seat control unit.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/15
SERVICE PROCEDURE
WARNING: This procedure involves working under the driver or front passenger seat. The
metal seat frame has sharp edges.
CAUTION: Handle interior trim carefully to avoid damage. Work with clean hands and
clean tools to avoid dirt and stains.
IMPORTANT: Follow all cautions, warnings, and notes in the Electronic Service Manual
(ESM) when working on or near a Supplemental Restraint System (SRS), such as an air
bag or OCS components.
NOTE: If equipped, Zero Point Reset needs to be performed after the passenger seat is reinstalled.
1. If equipped with a seat lifter, raise the height of the affected seat all the way to the
highest lifter position.
2. Write down all radio station presets.
Presets
AM
FM 1
FM 2
SAT 1
SAT 2/3
Bass
1
2
Treble
3
Balance
4
Fade
5
6
Speed Sen. Vol.
3. Turn the ignition OFF.
4. Disconnect the vehicle’s 12 volt battery or batteries.

Refer to the ESM for battery removal: ELECTRICAL & POWER CONTROL >
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS > REMOVAL AND
INSTALLATION – BATTERY.
5. Wait for at least 3 minutes.
6. Remove the affected seat from the vehicle and place it on a clean work surface.

Refer to the ESM for seat removal: BODY INTERIOR > SEAT > REMOVAL AND
INSTALLATION > FRONT SEAT.
2/15
NTB19-004
Climate controlled
seat control unit
harness connector
7. Disconnect the black climate controlled
seat control unit harness connector from
the control unit.
Climate
controlled seat
control unit
8. Visually inspect the harness connector
and control unit near the terminals.
Figure 1

If the harness connector or the control unit appears similar to Figure 3 and/or
Figure 5 (NG), proceed to step 9.

If the harness connector and the control unit appear similar to Figure 2 and Figure 4
(Good harness and connector), this bulletin does not apply. Refer to the ESM for
additional diagnostic information.
NOTE: See steps 46-52 for seat installation reference information.
Good harness connector
NG
Damaged
area
Figure 3
Figure 2
Good climate seat control unit
NG
Damaged
area
Figure 5
Figure 4
3/15
NTB19-004
Seat back
flap J-clip
9. Detach the seat back flap J-clip from the
seat frame.
Figure 6
Harness connectors
10. If equipped, remove the seat control
unit.
a. Disconnect the two (2) harness
connectors.
b. Remove the two (2) mounting
screws.
Seat
control unit
Figure 7
Climate
controlled seat
control unit
11. Remove the climate controlled seat
control unit.
a. Disconnect the one remaining
harness connector.
Harness
connector
b. Remove two (2) screws.
Figure 8
4/15
NTB19-004
Harness clip
12. Detach the harness clip shown in
Figure 9 from the seat frame.
13. Move the SRS harness out of the way
for the following steps, if so equipped.

Shown highlighted in yellow in
Figure 9.
SRS harness
NOTE: Not all seats have the SRS
harness routed as shown in Figure 9.
Figure 10 shows another possible
routing on a different seat.
Figure 9
14. Using a ruler measure approximately 30 mm from the left edge of the climate controlled
seat control unit mounting plate, and then mark as shown in Figure 10.
SRS harness
Edge of mounting plate
Figure 10
15. Measure approximately 9.4 mm (± 2 mm) from the bottom of the same mounting plate,
and then mark where the two measurements intersect as shown in Figure 11.
Figure 11
5/15
NTB19-004
16. Use a punch to make a slight indentation
at the intersection from steps 14 and 15.
17. Place a clean shop cloth under the
mounting plate to catch metal debris.
18. Drill a 7/16 inch (Number 3 drill bit) hole.

A pilot hole made with a smaller drill
bit may help.
NOTE: Take care to not damage the
seat when the drill bit passes through
the mounting plate.
Figure 12
19. Gently remove the shop cloth with metal debris from the seat.
20. Measure from the back end of the black
climate controlled seat control unit
harness connector.
Black climate controlled
seat control unit harness
connector
NOTE: This harness connector was
disconnected in step 7.

If working on a driver’s seat
measure 60 mm.

If working on a passenger seat
measure 65 mm.
Figure 13
21. Cut through the harness, at the point
that was measured to in step 20, with an
appropriate tool.
Figure 14
6/15
NTB19-004
10 mm
22. Remove approximately 10 mm of
insulation from the six (6) wires.
Figure 15
23. Measure from the harness side of the
new climate controlled seat control unit
harness connector (new harness) the
following amount:
NOTE: See the Parts Information
section of this bulletin for the new
harness connector.

If working on a driver’s seat
measure 70 mm.

If working on a passenger seat
measure 75 mm.
24. Cut through the new harness, at the
point that was measured to in step 23,
with an appropriate tool.
New harness
Figure 16
10 mm
25. Remove approximately 10 mm of
insulation from the six (6) wires of the
new harness.
Figure 17
7/15
NTB19-004
For steps 26-29, connect one wire at a time.
CAUTION: Do not use an electric type soldering tool. An electric type soldering tool may
generate a current that may damage vehicles’ control units.
26. Place a red solder sleeve onto one of
the wires of the new harness connector.

The solder sleeve connectors are
listed in the Parts Information
section of this bulletin.
27. Twist the new harness connector wire
(with solder sleeve) together with the
same colored wire of the harness that
was stripped in step 22.

See Figure 18 for example of twisting
wires.
Figure 18
28. Slide the red solder sleeve over the
twisted pair and position it so that the
solder ring is over the two twisted wires
as shown in Figure 19.
Figure 19
8/15
NTB19-004
29. Install the solder sleeve connector by
shrinking it to the wire with essential tool
Flameless Heat Gun J-46538 or
equivalent flameless heating tool (see
Figure 20 and Figure 21).
Figure 20
Installing the solder sleeve connector
will:

Melt the solder (silver ring inside the
solder sleeve connector) into the
exposed twisted wire area,

Melt the sealant (red rings inside the
solder sleeve connector) onto the
wires, and

Shrink the remainder of the solder
sleeve connector to the wire.
Figure 21
New climate controlled
seat control unit harness
connector
NOTE: Tool J-46538 can be
purchased from TECH-MATE at 1800-662-2001.
30. Perform steps 26-29 on the remaining
five (5) wires and then proceed to
step 31.

Figure 22 is shown with all solder
connections completed.
Figure 22
9/15
NTB19-004
31. Completely wrap the newly joined
harness with electrical tape as shown in
Figure 23.
Figure 23
32. Detach the “white harness clip” (clip) from the seat frame. See Figure 24 and Figure 25.
New harness wrapped in prior step
Clip
Clip
Figure 24
Clip

Clip shown detached from seat frame
in Figure 25.
Figure 25
10/15
NTB19-004
33. Remove the clip from the harness with an appropriate tool.

This clip will not be re-used.
34. Install the new clip onto the harness in the position shown in Figure 26.
NOTE: On most vehicles this will change the orientation of the new clip 180° relative to
the position of the old clip. See Figure 26.
35. Trim excess from the new clip with an appropriate tool.
Old clip
New clip
Clip
Front
of seat
Figure 26
Figure 27
36. Reinstall the clip into the seat frame.
Clip
Figure 28
11/15
NTB19-004
37. Measure 30 mm from the back end of
the black climate controlled seat control
unit harness connector.
38. Attach the black zip tie/harness clip
provided, where shown in Figure 29.

30 mm
Black zip
tie/harness clip
Excess zip
tie/harness clip
The black zip tie/harness clip is listed
in the Parts Information section of
this bulletin.
39. Trim excess from the zip tie/harness clip
with an appropriate tool.
Figure 29
Climate control
seat control unit
40. Install the new climate controlled seat
control unit to the seat frame.

Held by two (2) screws.

See the Parts Information section of
this bulletin.
Clip
41. Reattach the clip removed in step 12
and shown in Figure 30.
Figure 30
42. Connect the harness connectors to the
climate controlled seat control unit.
2 screws
Climate control
seat harness
connectors
43. Attach the black zip tie/harness clip from
step 38 to the seat frame.

Clip into the hole drilled in step 18.
Black zip
tie/harness clip
12/15
Figure 31
NTB19-004
44. Relocate the SRS harness (if so
equipped) back to its original position.
Seat back flap
J-clip
45. Reattach the seat back flap J-clip to the
seat frame
SRS harness
Figure 32
46. Reinstall the seat into the vehicle.

Refer to the ESM for seat installation: BODY INTERIOR > SEAT > REMOVAL AND
INSTALLATION > FRONT SEAT > Removal and Installation.

Torque the seat bolts in the order shown
in Figure 31).

Seat bolt torque: 48 N•m (4.9 kg-m, 35 ftlbs)
Figure 33
13/15
NTB19-004
47. Connect the vehicle’s 12 volt battery or batteries.

Refer to the ESM for battery removal: ELECTRICAL & POWER CONTROL >
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS > REMOVAL AND
INSTALLATION – BATTERY.
48. If equipped with a seat lifter; lower the height of the seat back to its original position.
49. Confirm climate controlled seat functions correctly.
50. If needed; perform Zero Point Reset for the passenger seat.

Refer to the ESM for Zero Point Reset procedure: RESTRAINTS > SRS AIRBAG
CONTROL SYSTEM > BASIC INSPECTION > INSPECTION AND ADJUSTMENT
> ZERO POINT RESET > Special Repair Requirements.
Year and Model
Non XD
2016-2019 Titan
XD without Crew Cab (CC)
XD Crew Cab (CC)
2016-2019 Murano
All
Zero Point Reset Needed
YES
YES
NO
YES
51. Turn the ignition OFF and then back ON and observe the air bag warning light:

The air bag warning light
should illuminate for 7 seconds and then go out.
NOTE: If the air bag warning light does not operate as described above there may
be an issue not covered by this bulletin. Refer to ASIST and the appropriate ESM for
additional diagnostic and repair information.
52. Reset any customer settings that were lost when the battery was disconnected.

Refer to the ESM, section ELECTRICAL & POWER CONTROL > POWER
SUPPLY, GROUND & CIRCUIT ELEMENTS > BASIC INSPECTION >
INSPECTION AND ADJUSTMENT > ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL, for a listing of systems that may lose settings or
memory when disconnecting the 12V battery.
 This list often includes items such as audio, HVAC, power windows, clock, etc.
14/15
NTB19-004
PARTS INFORMATION
DESCRIPTION
PART NUMBER
QUANTITY
HARNESS KIT
24061-9FT0A
1
Kit Includes:
Harness connector
1
Black Zip Tie/Harness Clip
1
White Harness Clip
1
Climate Controlled Seat Control Unit
(Titan)
873D6-9PF0A
1
Climate Controlled Seat Control Unit
(Murano)
873D6-5AA6A
1
24361-7990A
Use 3M/Scotch Professional
Grade Vinyl Super 88 Electrical
Tape (3/4 inch wide) or equivalent
6
Solder Sleeve (Red)
Electrical Tape
Shop
Supply (1)
(1) This product (or equivalent) is available at many local automotive supply stores, and
many local hardware stores.
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
Install Harness Kit on Driver Seat-Titan
Install Harness Kit on Driver Seat- Murano
Install Harness Kit on Passenger Seat-Titan
Install Harness Kit on Passenger Seat- Murano
OP CODE
SYM
DIA
1.3 hr
RX6YAA
(1)
FRT
ZE
RX6ZAA
32
0.9 hr
1.4 hr
1.0 hr
(1) Refer to the Electronic Parts Catalog and use the Control Box (873D6 -*****) as the
Primary Failed Part (PFP).
AMENDMENT HISTORY
PUBLISHED DATE REFERENCE
January 17, 2019
NTB19-004
DESCRIPTION
Original bulletin published
15/15
NTB19-004