01-168-09R

ATTENTION:
CLAIMS PERSONNEL q
IMPORTANT - All
Service Personnel
Should Read and
Initial in the boxes
provided, right.
SERVICE MANAGER
© 2016 Subaru of America, Inc. All rights reserved.
GENERAL MANAGER q
PARTS MANAGER
q
q
SERVICE BULLETIN
APPLICABILITY: 2000MY to Current, All Models
SUBJECT: Replacement Key and Immobilizer
		Information
NUMBER:
DATE:
Revised:
01-168-09R
06/17/09
01/10/20
INTRODUCTION
The purpose of this bulletin is to provide replacement key and immobilizer information along
with an overview of the Subaru Lock Information web-site.
OVERVIEW OF THE RETAILER-ONLY SUBARU LOCK INFORMATION SITE
The Subaru Lock Information Site (SLIS) is located at http://lockinfo.subaru.com, and
provides information on how to obtain immobilizer codes and key cut codes for Subaru
vehicles from the 2000MY to present. This bulletin identifies the equipment required to
initialize (reset) the immobilizer code and cut the key blanks, for both immobilizer and
non-immobilizer type keys. Subaru of America began using immobilizer systems in some
2005MY vehicles (please refer to Immobilizer Chart for more detailed information).
KEY BLANK TYPES
Subaru vehicles are equipped with either standard edge cut keys or high security laser cut
keys. All high security keys are equipped with an immobilizer device installed. Some standard
edge cut keys may or may not be equipped with an immobilizer device. Key blanks can be
purchased through normal parts channels. The following page are examples of the Subaru key
blank styles:
There are many different styles of key cuts. Be sure to order the correct blank for your
particular application and verify your key cutting equipment is compatible. Master keys
are shown below.
2005-2007 Legacy & Outback
edge cut key w/immobilizer (also
available without immobilizer)
2008-2011 Impreza, WRX, & STI
and 2012-2014 WRX & STI high
security laser cut key w/immobilizer
continued...
CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles,
or to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how to
do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.
Bulletin Number: 01-168-09R; Revised: 01/10/20
SUBARU OF AMERICA, INC. IS
ISO 14001 COMPLIANT
ISO 14001 is the international standard for
excellence in Environmental Management
Systems. Please recycle or dispose of
automotive products in a manner that is friendly
to our environment and in accordance with all
local, state and federal laws and regulations.
Page 1 of 19
2008 Legacy, Outback, and Tribeca edge cut
key w/immobilizer and keyless entry
2009-2013 Forester high security
laser cut key w/immobilizer
2009 Legacy & Outback and 2009-2014
edge cut key w/immobilizer and keyless
entry
2010-2014 Legacy & Outback high
security standard laser cut key
w/immobilizer and keyless entry
2012+ Impreza, 2013+ Crosstrek and
2014+ Forester, 2015+ Legacy & Outback,
and 2015+ WRX & STI edge cut key
w/immobilizer and keyless entry
2013+ BRZ edge cut key w/immobilizer
and keyless entry
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 2 of 19
2013-2014 BRZ keyless access with pushbutton start system access key with inside
cut high security laser cut emergency key,
immobilizer, and keyless entry
2013-2014 Legacy & Outback keyless
access with push-button start system access
key with high security laser cut emergency
key, immobilizer, and keyless entry
2014-2015 Forester, 2014 Crosstrek Hybrid,
and 2015 WRX & STI keyless access with
push-button start system access key with
inside cut high security laser cut emergency
key, immobilizer, and keyless entry.
(Different part number and key cutting
code from 2013 BRZ.)
2015+ BRZ, 2015+ Legacy, Outback,
Impreza, Crosstrek and 2016+ WRX, WRX
STI and Forester keyless access with push
button start system access key with singlesided inside cut high security laser cut
emergency key, immobilizer, and keyless
entry.
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 3 of 19
SUBARU VEHICLES EQUIPPED WITH ENGINE IMMOBILIZER SYSTEM
2005
2006
2007
2008
> 2009
Baja
Forester
Impreza
Legacy
Outback
Tribeca
BRZ
Crosstrek
n/a
n/a
----
2.5XT
2.5XT
2.5XT
2.5XT
All
STi
WRX, STi
WRX, STi
All
All
2.5GT
All
All
All
All
2.5XT, 3.0R
All
All
All
All
-All
All
All
All
----All
----All
WEB SITE ACCESS: AUTOMOTIVE SECURITY PROFESSIONALS
The public-facing locksmith site (linked off of STIS, via the “Immobilizer Key Access”
button), is a pay site for lock professionals.
WEB SITE ACCESS: AUTHORIZED SUBARU RETAILERS
Authorized Subaru Retailers can access SLIS through Subarunet (under the Service tab,
or by directly following the URL http://lockinfo.subaru.com. Access to the immobilizer
information is restricted to Subaru Dealership Service Managers and Parts Managers. Access
will be granted by using the managers’ SKILS user name. No other employees can access the
Subaru Immobilizer Database.
Note: It is the retailers’ responsibility to perform due diligence by entering or deleting
employees in the SKILS Dealer Employee Maintenance Database. This is especially true
of Service Manager and Parts Manager position changes.
Step by Step Process To Access the Site
• Once on the SLIS home page, the Service Manager or Parts Manager will be asked for
their SKILS user name. At that time, if this is the first time he/she has logged on to the
web site, the password “Welcome” should be used. He/she will then be prompted to create
a new password (this will not change your current SKILS password).
• The Service Manager or Parts Manager will then be prompted to read the disclaimer and
answer “accept” or “not accept”. If they answer “not accept”, the system will not let them
access the immobilizer information.
• A page will then be displayed, allowing for entry of the full 17 character VIN of the vehicle
in question.
• Provided the VIN is found in the database, the immobilizer Security ID along with the key/
cutting code will appear.
• A charge of $2.80 will be incurred for each immobilizer request.
Note: Costs are $9.95 per transaction, or $25.95 for a 24 hour subscription access
(with no transaction limit).
SOA Warranty will only reimburse an approved warranty claim with an Immobilizer
Code access cost of $2.80 per transaction, as a sublet cost. The public-facing
(professional locksmith) web site’s public access fees of $9.95 and $25.95 will
be reduced to $2.80 per transaction, if those fees are submitted as a part of a
warranty claim.
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 4 of 19
NASTF SECURE DATA RELEASE MODEL (SDRM)
Positive Identification Policy
NASTF SDRM Subaru Parts and Service Managers who are registered in the Dealer
Employee Maintenance Database and are designated as Registry Vehicle Security
Professionals (VSPs) shall comply with the following Positive Identification Policy when
servicing orders for keys, immobilizer reset, or other anti-theft services for vehicles:
1. Inform the Customer - At the time of initial request, ask the customer whether he or
she has identification and authority for the service. Inform them of the requirements of this
Positive Identification Policy.
2. Complete the Form - Upon arrival at the job site or when the customer comes in, the VSP
shall complete an Authorization for Automotive Key Generation and/or Immobilizer System
/ Anti-Theft Services form (aka Form D-1, page 15) that asks for the name, address, phone
number, driver’s license, vehicle make, model and year, vehicle license plate number, Vehicle
Identification Number (VIN), odometer reading, and disclaimer and signature. An invoice or
work order that contains all identifying information, when stapled to a duly signed Form D-1,
is acceptable for collection of this customer information. Subarunet.com user name should be
used in place of LSID.
3. Verify I.D. - Verify the customer’s valid photo ID and compare to the information provided
by the customer on the authorization form. The customer must present a valid state issued
driver’s license as proof of identity to qualify for use of Registry services.
4. Verify Authority - Ask the customer to present proof of entitlement, which shall include
at least one of the following: a valid registration certificate, a valid insurance ID card, a valid
insurance policy, vehicle title or a certificate of ownership for the vehicle. The name and
address on the proof of entitlement document must match the information on the driver’s
license to qualify for use of Registry services. In the event that necessary documentation is
locked within the vehicle, the vehicle may be entered to verify the authority of the requestor.
If upon entry to the vehicle, you are unable to verify the authority of the requestor, the vehicle
shall be shut and locked. Do not produce a replacement key, do not provide any key related
information to the requestor and destroy all information acquired from the automaker during
the transaction.
5. Ask for Signature - Require the customer to read and sign Form D-1(page 15). The
customer is attesting to:
a. the information given by the customer being correct and truthful,
b. the customer having the authority to obtain keys or immobilizer services for the vehicle
and,
c. the customer agreeing to indemnify and hold harmless the service provider and related
parties against liability.
6. File the Form - Keep the completed Form D-1 on file for two (2) years, or longer as
required by law.
7. Compliance with Applicable Laws. The VSP will take all other actions required by
applicable laws. In the event of a conflict between the steps set forth herein and the applicable
laws, the VSP should comply with applicable laws.
8. Sublet work - A mobile VSP doing work for a body shop, garage, or dealership may accept
a legible photocopy of the picture I.D. in order to match it to the registration/title documents.
This cannot be a faxed copy. The shop owner or manager must verify the customer’s I.D. in
person and attest they have done so by signing the bottom of the Form D-1
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 5 of 19
EQUIPMENT
The Subaru Diagnostic System (SDS) is required to reprogram Subaru immobilizer codes.
See the Subaru Technical Information System (STIS) (http://techinfo.subaru.com) for more
information. Instructions for Immobilizer re-initialization for keys, etc., can be found in the
applicable Immobilizer Manual on STIS.
TEACHING OPERATION CODES
A Teaching Operation Code may be needed. The following are the necessary Teaching Codes:
VEHICLE LINE
Legacy
Impreza
Forester
Tribeca
MODEL YEAR
2005-2014
2005~07
2008-2011
2005~08
2009-2013
2006-2014
TEACHING CODE
3781
3178
3781
3178
3781
3781
KEY CUTTING MACHINERY RECOMMENDATIONS
Subaru of America recommends the use of the Class C Solutions Group “BD Laser Max” key
cutting machine for standard edge cut and high security laser cut keys.
Consult http://subaru.service-solutions.com for key machine purchases.
BD Laser Max
RETAILER CENTRALIZED KEY CUTTING SERVICE
The Subaru of America Parts Department offers a key cutting service for retailers who
have not purchased the key cutting machine. The service program details can be found on
Subarunet.com, in the Parts Operations area, using the “Key Request” link. Forms, details,
and costs are found in this area of Subarunet.com.
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 6 of 19
Key Cutting Tips For Using a BD Laser Max
Every Subaru vehicle has a key code that can be found on the original key ring tag and on Subarunet. This code is
known as an indirect (obfuscated) code. To cut a key, the indirect code must be translated to the direct code which is
the actual key cutting depth information.
Behind the scenes there is a database for each key type which converts the indirect key codes into the respective
direct depth codes required to cut a key. In the past Subaru provided third party companies with this database so
they could program their key cutting machines for indirect code cutting. The indirect key code could be typed into
the key machine and the key machine would automatically convert the indirect code into the direct depth code and
cut the key.
For security reasons Subaru is no longer providing this database. The keys for newer Subaru models must be cut using the direct method. The direct code cut depth information for a given key must be obtained through Subaru Lock
Information Service (SLIS).
The following information will guide you through both indirect and direct depth key cutting methods.
Prior to Using Machine
1. Locate model and model year in the Key Type & Cutting Information chart found on the
following pages to find the vehicle specific cutting information
2. Note Cut By, Jaw, Cutter Size and Adapter requirement
3. If the Cut By is listed as Code, obtain the key code for the vehicle through Subaru.net or
through the SLIS service (listed as Key No in SLIS)
4. If the Cut By is listed as Depth, obtain the Depth Code through the SLIS service (listed as
Key Code in SLIS)
Machine Tips
1. To limit the selection to US market vehicles, from the Main menu go to Cars and change
region to North America
2. Maintain up-to-date software. Software releases prior to March 2016 will not cut all
of the keys listed in this bulletin. Refer to attached BD Laser Max instructions for
updating software and sign up for software update alerts at https://blueclassc.mscdirect.com/
acton/form/1684/0039:d-0001/0/index.htm
3. When inserting a key blank into the jaw, make sure that the jaw is clear of debris
4. Press down on the blank as you tighten the jaw to ensure that the blank is fully seated
Cutting a Subaru Key
1. From the main menu, select CARS
2. Select Subaru
3. Select Subaru model
4. Select the row with the year range and key type
5. If cut by code, select CODES and input the key code
6. If cut by depth, select DIRECT and input the depth code per the input sequence chart
7. Follow the machine prompts to set up the required cutter size and jaw type
8. Follow the machine prompts to set up the tip stop or adapter (if required). For assistance in
setting up the tip stop and adapter refer to following pages for more information
9. If application calls for F/G jaw, either a F or G jaw can be used
10. If an original key is available, check that the image of the key cut matches the original key
and proceed with cutting the key
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 7 of 19
KEY TYPE & CUTTING INFORMATION (Legend for charts on Pages 8-11):
Multiple part numbers = Refer to Electronic Parts Catalog for the correct VIN specific part number
Sub Master = Master Key without remote keyless entry functions
Valet = Door and ignition only. No remote keyless entry functions. Will not unlock glovebox on Forester
and Outback, trunk and glovebox on Legacy and 2008-2011 Impreza, and trunk on BRZ
Push-Button Start Emergency = Emergency Key for Keyless Access with Push-Button Start
Pre-cut available = A pre-cut replacement key can be ordered through the TRMI service
Tip Stop Setup for A and C Jaws
A and C jaws use an integrated tip stop that slides into place when required
Tip Stop Integrated Into Jaw
Tip Stop Setup for F/G Jaw
F/G jaws use a magnetic tip stop that is placed into the required grooved track
Tip Stop In G1 Position
Magnetic
Tip Stop
Adapter (AD03) Setup
4IT 4+4 thin type emergency keys require use of the AD03 adapter that is
placed into the jaw as shown prior to inserting the key blank
Adapter AD03
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 8 of 19
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 9 of 19
Impreza
Model
Master
Sub Master
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Key Type & Cutting Information
57497FL00A
57497FL08A
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2018MY
57497FG010
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
57497AG070
-
2008MY
Master
Sub Master
Key Type & Cutting Information
2019MY
2020MY
57497FG090
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2010MY
57497FG080
-
57497XC01A 57497XC01A
57497FL08A 57497FL08A
Yes
Yes
Edge
Edge
10
10
32000 - 39999 32000 - 39999
Depth
Depth
F/G
F/G
1.5 mm
1.5 mm
No
No
57497AL02A 57497AL02A
Yes
Yes
Laser
Laser
4IT 4+4 thin
4IT 4+4 thin
90000 - 94999 90000 - 94999
Depth
Depth
C
C
2.5 mm
2.5 mm
Yes
Yes
57497FG010
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2009MY
57497AG070
57497FG170
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2011MY
57497FG160
-
2013MY
57497FJ021
57497FJ090
Yes
Yes
Edge
Edge
10
10
32000 - 39999 32000 - 39999
Depth
Depth
F/G
F/G
1.5 mm
1.5 mm
No
No
-
2012MY
57497FJ021
57497FJ090
2014MY
57497FJ021
57497FJ090 /
57497FJ250
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2015MY
57497FJ230
57497FJ250
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2016MY
57497FJ230
57497FJ250
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2017MY
57497FL00A
57497FL08A
Bulletin Number: 01-168-09R; Revised: 01/10/20
2019MY
2009MY
57497AG070
57497FG010
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2020MY
2010MY
57497FG080
57497FG090
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
57497FJ230
57497FJ230
5749VA330
57497FJ250
57497FJ250
57497FJ250
Yes
Yes
Yes
Edge
Edge
Edge
10
10
10
32000 - 39999 32000 - 39999 32000 - 39999
Depth
Depth
Depth
F/G
F/G
F/G
1.5 mm
1.5 mm
1.5 mm
No
No
No
57497AL020 57497AL020 57497AL020
Yes
Yes
Yes
Laser
Laser
Laser
4IT 4+4 thin
4IT 4+4 thin
4IT 4+4 thin
90000 - 94999 90000 - 94999 90000 - 94999
Depth
Depth
Depth
C
C
C
2.5 mm
2.5 mm
2.5 mm
Yes
Yes
Yes
2018MY
Master
Sub Master
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
57497AG070
57497FG010
Yes
Laser
T0001-3000
T0001-3000
Code
A
2.5 mm
No
-
WRX / STI Key Type & Cutting Information
Master
Sub Master
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
2008MY
Model
Key Type & Cutting Information
continued...
Page 10 of 19
2011MY
57497FG160
57497FG170
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2012MY
57497FG160
57497FG170
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2013MY
57497FG160
57497FG170
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2014MY
57497FG160
57497FG170
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
T0001-3000
-
2015MY
57497FJ021
57497FJ090
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497FJ060
Yes
Laser
4IT 5+4
77000 - 78569
Depth
A
2.5 mm
No
2016MY
57497FJ230
57497FJ250
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2017MY
57497FJ230
57497FJ250
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 11 of 19
Forester
Model
BD Laser Setup
Cut By
Jaw
Cutter Size
Adapter Required
Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup
57497FJ230
57497SG000
Yes
Edge
10
32000 39999
Depth
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 94999
Depth
C
2.5 mm
Yes
2018MY
Master
Sub Master
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
Key Type & Cutting Information
2020MY
2010MY
57497SC010
57497SC020
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
57497SJ050 57497SJ050
57497SJ000 57497SJ000
Yes
Yes
Edge
Edge
10
10
32000 32000 39999
39999
Depth
Depth
F/G
F/G
1.5 mm
1.5 mm
No
No
57497AL020 57497AL020
Yes
Yes
Laser
Laser
4IT 4+4 thin 4IT 4+4 thin
90000 90000 94999
94999
Depth
Depth
C
C
2.5 mm
2.5 mm
Yes
Yes
2019MY
2009MY
57497FC000 57497SC010
57497FC030 57497SC020
No
Yes
Edge
Laser
10
4ET 5+5
30001-37850 T0001-3000
Code
Code
F/G
A
1.5 mm
2.5 mm
No
No
-
2008MY
Master
Sub Master
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Key Type & Cutting Information
2011MY
2012MY
57497AJ070 57497AJ070
57497AJ010 57497AJ010
Yes
Yes
Laser
Laser
4ET 5+5
4ET 5+5
T0001-3000 T0001-3000
Code
Code
A
A
2.5 mm
2.5 mm
No
No
-
2013MY
57497AJ070
57497AJ010
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2014MY
57497FJ021
57497SG000
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497FJ060
Yes
Laser
4IT 5+4
77000 - 78569
Depth
A
2.5 mm
No
2015MY
57497FJ021
57497SG000
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497FJ060
Yes
Laser
4IT 5+4
77000 - 78569
Depth
C
2.5 mm
No
2016MY
57497FJ230
57497SG000
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2017MY
57497FJ230
57497SG000
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2018MY
57497FJ230
57497SG000
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 12 of 19
Crosstrek
Model
BD Laser Setup
Cut By
Jaw
Cutter Size
Adapter Required
Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
2018MY
57497FL000
57497FL080
Yes
Edge
10
32000 39999
Depth
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 94999
Depth
C
2.5 mm
Yes
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Key Type & Cutting Information
Master
Sub Master
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup
2008MY
-
Key Type & Cutting Information
Master
Sub Master
2010MY
-
2019MY
2020MY
57497SJ050 57497SJ050
57497FL080 57497FL080
Yes
Yes
Edge
Edge
10
10
32000 32000 39999
39999
Depth
Depth
F/G
F/G
1.5 mm
1.5 mm
No
No
57497AL020 57497AL020
Yes
Yes
Laser
Laser
4IT 4+4 thin 4IT 4+4 thin
90000 90000 94999
94999
Depth
Depth
C
C
2.5 mm
2.5 mm
Yes
Yes
2009MY
-
2011MY
-
-
2012MY
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
-
2013MY
57497FJ021
57497FJ090
2014MY
57497FJ021
57497FJ090 /
57497FJ250
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497FJ060
Yes
Laser
4IT 5+4
77000 - 78569
Depth
A
2.5 mm
No
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2015MY
57497FJ230
57497FJ250
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2016MY
57497FJ230
57497FJ250
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2017MY
57497FJ230
57497FJ250
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 13 of 19
57497AL27A
57497AL02A
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2018MY
Master
Sub Master
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Key Type & Cutting Information
Legacy
57497AG35A
57497AG12A
No
Edge
10
30001-37850
Code
F/G
1.5 mm
No
-
2008MY
Master
Sub Master
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Key Type & Cutting Information
Model
57497AL37A
57497AL01A
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2019MY
2009MY
57497AG48A
57497AG12A
No
Edge
10
30001-37850
Code
F/G
1.5 mm
No
57497AN00A
57497XC00A
Yes
Edge
10
32000-39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2020MY
2010MY
57497AJ00A
57497AJ01A
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2011MY
57497AJ10A
57497AJ01A
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2012MY
57497AJ10A
57497AJ01A
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2013MY
57497AJ10A
57497AJ01A
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
57497AJ11A
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
2014MY
2015MY
57497AJ10A 57497AL00A
57497AJ01A 57497AL01A
Yes
Yes
Laser
Edge
4ET 5+5
10
T0001-3000 32000 - 39999
Code
Depth
A
F/G
2.5 mm
1.5 mm
No
No
57497AJ11A 57497AL02A
Yes
Yes
Laser
Laser
4ET 5+5
4IT 4+4 thin
T0001-3000 90000 - 94999
Code
Depth
A
C
2.5 mm
2.5 mm
No
Yes
2016MY
57497AL00A
57497AL01A
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2017MY
57497AL00A
57497AL01A
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 14 of 19
57497AL27A
57497AL02A
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2018MY
Master
Sub Master
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Key Type & Cutting Information
Outback
57497AG35A
57497AG12A
No
Edge
10
30001-37850
Code
F/G
1.5 mm
No
-
2008MY
Master
Sub Master
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Key Type & Cutting Information
Model
57497AL37A
57497AL01A
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2019MY
2009MY
57497AG48A
57497AG12A
No
Edge
10
30001-37850
Code
F/G
1.5 mm
No
57497AN00A
57497XC00A
Yes
Edge
10
32000-39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2020MY
2010MY
57497AJ00A
57497AJ01A
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2011MY
57497AJ10A
57497AJ01A
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2012MY
57497AJ10A
57497AJ01A
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
-
2013MY
57497AJ10A
57497AJ01A
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
57497AJ11A
Yes
Laser
4ET 5+5
T0001-3000
Code
A
2.5 mm
No
2014MY
2015MY
57497AJ10A 57497AL00A
57497AJ01A 57497AL01A
Yes
Yes
Laser
Edge
4ET 5+5
10
T0001-3000 32000 - 39999
Code
Depth
A
F/G
2.5 mm
1.5 mm
No
No
57497AJ11A 57497AL02A
Yes
Yes
Laser
Laser
4ET 5+5
4IT 4+4 thin
T0001-3000 90000 - 94999
Code
Depth
A
C
2.5 mm
2.5 mm
No
Yes
2016MY
57497AL00A
57497AL01A
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2017MY
57497AL00A
57497AL01A
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 15 of 19
BRZ
Model
2018MY
57497CA310
Key Type & Cutting Information
Master
BD Laser Setup
Cut By
Jaw
Cutter Size
Adapter Required
Cut By
Jaw
BD Laser Setup
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
Sub Master
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
-
Master
Sub Master
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
2019MY
-
2009MY
2020MY
-
2010MY
57497CA310
57497CA250 57497CA250
Yes
Yes
Edge
Edge
10
10
50000 50000 - 69999
69999
Code
Code
F/G
F/G
1.5 mm
1.5 mm
No
No
57497AL020 57497AL020 57497AL020
Yes
Yes
Yes
Laser
Laser
Laser
4IT 4+4 thin 4IT 4+4 thin 4IT 4+4 thin
90000 90000 - 94999 90000 - 94999
94999
Depth
Depth
Depth
C
C
C
2.5 mm
2.5 mm
2.5 mm
Yes
Yes
Yes
2008MY
Key Type & Cutting Information
-
2011MY
-
2012MY
2013MY
57497CA110
57497CA250
Yes
Edge
10
50000 - 69999
Code
F/G
1.5 mm
No
57497CA200
Yes
Laser
4IT 5+5
40000 - 49999
Depth
C
2.5 mm
No
2014MY
57497CA110
57497CA250
Yes
Edge
10
50000 - 69999
Code
F/G
1.5 mm
No
57497CA200
Yes
Laser
4IT 5+5
40000 - 49999
Depth
C
2.5 mm
No
2015MY
57497CA310
57497CA250
Yes
Edge
10
50000 - 69999
Code
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2016MY
57497CA310
57497CA250
Yes
Edge
10
50000 - 69999
Code
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2017MY
57497CA310
57497CA250
Yes
Edge
10
50000 - 69999
Code
F/G
1.5 mm
No
57497AL020
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 16 of 19
Tribeca
Model
Ascent
Model
2019MY
57497XC01A
57497XC00A
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
2020MY
57497XC01A
57497XC00A
Yes
Edge
10
32000 - 39999
Depth
F/G
1.5 mm
No
57497AL02A
Yes
Laser
4IT 4+4 thin
90000 - 94999
Depth
C
2.5 mm
Yes
Key Type & Cutting Information
2008MY
2009MY
2010MY
2011MY
2012MY
Master
57497AG35A 57497AG48A 57497XA12A 57497XA20A 57497XA20A
Sub Master
Valet
57497AG12A 57497AG12A 57497XA13A 57497XA13A 57497XA13A
Pre-cut available
No
No
No
No
No
Cut Type
Edge
Edge
Edge
Edge
Edge
Key Type
10
10
10
10
10
Key Code Series
30001-37850 30001-37850 30001-37850 30001-37850 30001-37850
Cut By
Code
Code
Code
Code
Code
Jaw
F/G
F/G
F/G
F/G
F/G
BD Laser Setup
Cutter Size
1.5 mm
1.5 mm
1.5 mm
1.5 mm
1.5 mm
Adapter Required
No
No
No
No
No
Push Button Start Emergency
-
Master
Sub Master
Valet
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Push Button Start Emergency
Pre-cut available
Cut Type
Key Type
Key Code Series
BD Laser Setup Cut By
Jaw
Cutter Size
Adapter Required
Key Type & Cutting Information
2013MY
57497XA20A
57497XA13A
No
Edge
10
30001-37850
Code
F/G
1.5 mm
No
-
2014MY
57497XA20A
57497XA13A
No
Edge
10
30001-37850
Code
F/G
1.5 mm
No
-
Depth Code Input Sequence
Edge cut key depth code input sequence
2012MY+ Impreza, 2015MY+ WRX/STI 2013MY+ Crosstrek,
2014MY+ Forester, 2015MY+ Legacy, 2015MY+ Outback
The machine will automatically populate the second row
Depth Code: 1-2-3-4-5-6-7-8-9-10
1 2 3 4 5 6 7 8 9 10
Key
Key Blank
Blank
Emergency key depth code input sequence (4IT 4+4 key)
2015MY+ Impreza, 2016MY+ WRX/STI 2015MY+ Crosstrek,
2016MY+ Forester, 2015MY+ Legacy, 2015MY+ Outback,
2015MY+ BRZ
Enter code in reverse order from sequence provided
Depth Code: 1-2-3-4-5-6-7-8
8
7
6
5
4
3
2
1
Key Blank
Emergency key depth code input sequence (4IT 5+5 key)
2013-14MY BRZ
Enter code in reverse order from sequence provided
Depth Code: 1-2-3-4-5-6-7-8-9-10
10
9
8
7
6
5
4
3
2
1
Key
KeyBlank
Blank
Emergency key depth code input sequence (4IT 5+4 key)
2015MY WRX/STI, 2014MY Crosstrek, 2014-15MY Forester
Enter code in reverse order from sequence provided
Depth Code: 1-2-3-4-5-*-7-8-9-10
10
9
8
7
*
5
4
3
2
1
Key Blank
Blank
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 17 of 19
BD Laser Max Keyonline Via PC (USB Memory Stick) Update Instruction
USB Memory stick requirements: 2-4 GB flash/thumb drive. Drive must be free of information
prior to performing the update.
1. From the main menu select:
a. Setup
b. Updates
c. Keyonline via pc
i. Do you want to update the software?
1. Select “Yes”.
ii. Please insert the USB memory stick in to the console and press “OK”.
1. The BD Laser Max will then transfer a “.csk” file to the USB memory
stick.
iii. Once the file transfer is complete the machine will display “Please remove
the USB memory stick, download the update from Keyonline website on your
personal computer and save it on the USB memory stick”
1. Select “OK” and remove the USB memory stick from the console.
2. Insert USB memory stick in to desktop/laptop.
3. Visit http://bdlaser.mscdirect.com/
4. Double click “choose file”.
5. Search and select the “.csk” file downloaded from the BD Laser Max and select “open”.
6. Click “request update”
a. A dialogue box with the message “This action may require some time. Please wait”
will appear. Select “OK”.
7. The update package will then be created.
a. Once the package creation is completed select
i. For Windows users: Select “SAVE” and then “SAVE AS” under the drive that
is associated with your USB drive.
ii. For Chrome users: Select the “Show in folder” option, then pull to transfer the
file to the USB drive.
8. Once the download/transfer is complete, safely eject the USB memory stick from the
desktop/laptop.
9. Return to the BD Laser Max which displays the message “Please insert the USB memory
stick containing the update”.
a. Insert the USB memory stick and select “OK”.
10. The BD Laser Max will then display the message “Do you want to update the software?”
a. Select “yes”.
b. Please note: The update process may take some time.
11. Once the update file transfer is complete the machine will display “Software update successfully installed”. Select “OK” then remove the USB memory stick and save for future use.
1301 E. 9th Street Suite, #700 ∙ Cleveland, OH 44114
Email: [email protected] ∙ Phone: 866-438-6767
Confidential – Property of Class C Solutions Group, a business of MSC Industrial Supply Co.
continued...
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 18 of 19
Form D1
AUTHORIZATION FOR AUTOMOTIVE KEY GENERATION
and/or IMMOBILIZER SYSTEM/ANTI-THEFT SERVICES
(The LSID Holder must fill out this form, after personally looking at the photo I.D., the registration and the VIN plate on the Vehicle.
These forms are to be kept for 2 years in a secured location as per the NASTF positive I.D. Policy. The NASTF Director of
Operations will randomly audit these forms to ensure compliance with positive I.D policy. Failure to produce D-1 Forms when
requested will result in LSID registry suspension and possible termination.)
I hereby certify that I have the authority to order keys and immobilizer system reset services for the vehicle indicated below. I agree that the
information I am providing is true and correct. Further, to the maximum extent permitted by applicable law, I agree to indemnify and hold
harmless the service provider listed below and related parties providing security information from any and all liability or claims that may arise
from the performance of this service. I further agree to indemnify the automaker and their affiliates, successors, assignees, and nominees
from any and all claims, losses, or costs (including reasonable attorney's fees) arising from any acts or omissions of the service provider, the
service provider’s employees, subcontractors, or agents.
Vehicle Owner/Customer Name:
Address:
City / State / Zip Code:
Telephone:
|
Vehicle Owner/Customer Signature
Driver’s License Number 1
State
Date
Expiration Date
Other Form of ID (specify type and number):
Vehicle Year
|
|
Make
License Plate Number
|
Model
Color:
State of Vehicle Registration
Vehicle ID Number (VIN) (17 characters)
Odometer Reading (mileage):
(or)
For Dealership/Auctions:
PO / Stock #
Service Performed:
 Key cut from code
Not Available: 
/
 Immobilizer reset
 Other (describe below) :
VSP/Service Provider Business Name:
Phone:
Address:
City / State / Zip Code:
VSP/Technician Name
VSP/Technician Signature
Contracting Shop Owner/Manager Signature
(Item 8 of the Positive ID Policy)
|
Subaru.net Username
|
/
|
/
/
Date
/
1
IMPORTANT: Mobile Service Providers - If the VSP is not present at the time vehicle is received for service by a contracting service facility, the contracting service facility must make a
photocopy of the vehicle owner’s driver’s license and attach to this form. Additionally, a valid registration must be left with the vehicle so that the VSP can verify that the driver’s license
matches the ownership documentation.
Bulletin Number: 01-168-09R; Revised: 01/10/20
Page 19 of 19