MI20-14
Service Bulletin Details
Public Details for: MI20-14
Prevost driver assistâ¿¢ - windshield replacement equipped with camera
- 2022 - 2021 - 2020 - 2019 - 2018 - 2017 -
Models from 2022
2022 PREVOST X3-45 |
Models from 2021
2021 PREVOST H3-41 |
2021 PREVOST H3-45 |
2021 PREVOST H3-45 VIP |
2021 PREVOST X3-45 |
2021 PREVOST X3-45 VIP |
Models from 2019
2019 PREVOST H3-41 |
2019 PREVOST H3-45 |
2019 PREVOST H3-45 VIP |
2019 PREVOST X3-45 |
2019 PREVOST X3-45 VIP |
Models from 2018
2018 PREVOST H3-41 |
2018 PREVOST H3-45 |
2018 PREVOST H3-45 VIP |
2018 PREVOST X3-45 |
2018 PREVOST X3-45 VIP |
Models from 2017
2017 PREVOST H3-45 |
2017 PREVOST H3-45 VIP |
2017 PREVOST X3-45 |
2017 PREVOST X3-45 VIP |
MAINTENANCE INFORMATION DATE : SUBJECT : October 2020 MI20-14 SECTION : 23 ACCESSORIES PREVOST DRIVER ASSIST™ - WINDSHIELD REPLACEMENT EQUIPPED WITH CAMERA First Release October 2020 Table of content MATERIAL .................................................................................................................................. 2 Required parts: ........................................................................................................................ 2 Other parts or material that may be required: ........................................................................... 2 PROCEDURE ............................................................................................................................. 2 PARTS / WASTE DISPOSAL ...................................................................................................... 5 R.H. WINDSHIELD NEEDS TO BE REPLACED Writer: EL REMOVE CAMERA. INSTALL NEW SUPPORT POSITIONED WITH MARKINGS ON THE NEW WINDSHIELD. REINSTALL CAMERA NEW CALIBRATION NOT NEEDEDMI20-14 Page 2 / 5 MATERIAL Required parts: Part No. 300720 (H3 Series) or 300723 (X3 Series) 880060 Description Qty CURBSIDE WINDSHIELD R.H. 1 BRACKET, CAMERA 1 Other parts or material that may be required: Part No. G37362 (H3 Series) Description TEMPLATE, CAMERA POSITION MARKINGS (if windshield doesn’t already have position markings) Qty 1 G37276 (X3 Series) PROCEDURE DANGER Park vehicle safely, apply parking brake, stop the engine. Prior to working on the vehicle, set the ignition switch to the OFF position and trip the main circuit breakers equipped with a trip button. On Commuter type vehicles, set the battery master switch (master cut-out) to the OFF position. Lock out & Tag out (LOTO) must be performed during set-up, maintenance or repair activities. Refer to your local procedure for detailed information regarding the control of hazardous energy. Writer: EL MI20-14 Page 3 / 5 1. Unscrew the two screws at the lower end of the Prevost Driver Assist system camera housing and then remove the cable holder. 2. On both sides of the camera, insert a small flat blade screwdriver in the opening. 3. Gently prying by moving the screwdriver handles away from the windshield a small amount – push against the retaining clips to release the camera (see image below with the camera hidden to show the mechanism). Writer: EL MI20-14 Page 4 / 5 4. Detach the camera and set aside. 5. Remove and discard the broken windshield with existing camera bracket glued to it. 6. Install the new windshield. 7. If the new windshield came without camera position markings: Use template G37362 (H3) or G37276 (X3) to draw the position markings shown in red on the image below. Writer: EL MI20-14 Page 5 / 5 8. Peel off double-side tape and line up the new bracket with markings. 9. Reinstall the camera onto the new bracket. PARTS / WASTE DISPOSAL Discard according to applicable environmental regulations (Municipal/State[Prov.]/ Federal) Access all our Service Bulletins on http://techpub.prevostcar.com/en/ Or scan the QR-Code with your smart phone . Are you a Vehicle owner? E-mail us at [email protected] and type “ADD” in the subject to receive warranty bulletins applicable to your vehicle(s) by e-mail. Writer: EL