Prevost H3-45 Vip 2018

Vehicle Details: Recalls, Investigations, Service Bulletins

Below you will find all available information on the 2018 PREVOST H3-45 Vip.

ManufacturerKnown WMI(s)Fuel Type
PREVOST
PREVOST VIN Decoder

Use the box here to look up VINs from PREVOST as well as other manufacturers

#
Frequently Asked Questions
  • Are there recalls for the 2018 PREVOST H3-45 Vip?
     - There are 7 recall(s) for the 2018 PREVOST H3-45 Vip, additional information is below.
NHTSA Mandated Recalls
  • Recall 260247 [USA]: Beacons that do not provide proper illumination may be less visible to wheelchair lift users, increasing the risk of injury.

  • Recall 240591 [USA]: The activation of the automatic fire suppression system can cause a sudden loss of drive power, increasing the risk of a crash. additionally, a disabled coach may require an evacuation procedure in an uncontrolled traffic situation, increasing the risk of injury to passengers.

  • Recall 191910 [USA]: An overheated alternator bearing can increase the risk of a fire.

  • Recall 147410 [USA]: If the engine unexpectedly shuts down, passengers may have to be transferred to another vehicle on the side of the road, increasing the risk of an injury. if the engine unexpectedly shuts down while the vehicle is in motion, there is an increased risk of crash.

  • Recall 140677 [USA]: If the fire suppression system does not work as intended, it can increase the risk of injury in the event of a fire.

  • Recall 133711 [USA]: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.

  • Recall 138388 [USA]: If the fuel tank separates from the vehicle, it could be a road hazard and the vehicle would stall. either scenario increases the risk of a crash.

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • IS-23019 - SUSPENSION: Sway bar collars improvement
  • IS-22106 - EQUIPMENT: H3 lavatory fan retrofit kit
  • IS-21089 - ENGINE AND ENGINE COOLING: Efd h3 vip condenser repositioning
  • IS-18106 - STEERING: Kit power steering tank convertion cummins to zf with d13 engine
  • IS-19910i - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with delco remy alternator. Revision : i note added regarding power cable connection
  • IS-19900J - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with bosch alternator. Revision : j - note added regarding power cable connection
  • IS-21072B - ELECTRICAL SYSTEM: Steering gateway. Revision b - pin 2 and 10 were inverted on connector a139
  • MI22-12B - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: b - general update
  • SP18-35J - ENGINE AND ENGINE COOLING: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency. Revision j - range of applicable vins updated.
  • MI22-12A - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: a - erroneous secondary & accessory tanks location.
  • MI22-12 - SERVICE BRAKES, AIR: Air tanks draining sequence
  • IS-17151C - EXTERIOR LIGHTING: Halogen to led fog light replacement kit. Revision: c - advanced kits canceled
  • SP18-35J - ENGINE AND ENGINE COOLING: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency. Revision j - range of applicable vins updated.
  • IS-22902 - WHEELS: Tag axle hub flange - alternate cap screw
  • IS21-072 - ELECTRICAL SYSTEM: Steering gateway, revision a : cancel watch dog removal from efd part of the instruction
  • MI20-08C - EQUIPMENT: Storage and startup guidelines : part number updates
  • IS21-072A - ELECTRICAL SYSTEM: Steering gateway revision a cancel watch dog removal from efd part of the instruction
  • IS20-925A - VISIBILITY: Central hvac merv filters installation
  • IS20-932A - EQUIPMENT: H3 series envirocare - ions air sanitizer
  • IS22-040 - EQUIPMENT ADAPTIVE/MOBILITY: Brake pedal seal plate installation kit
  • IS21-072 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Steering gateway schematic
  • SP18-35H - EQUIPMENT: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • SP18-35H - EQUIPMENT ADAPTIVE/MOBILITY: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • IS19_908E - ELECTRICAL SYSTEM: Bosch to delco remy alternator installation, h3-45 revision : e, updated electrical schematic. Added instructions for h series ghg17 engine variant.
  • SP18-39D - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Scr converter replacement - aftertreatment system
  • SP18-35H - EQUIPMENT:MECHANICAL: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • MI18-16B - ELECTRICAL SYSTEM: Bosch hd10 alternator diagnostic guide revision b to avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
  • SP18-35H - POWER TRAIN: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • MI21-13A - EQUIPMENT: An automated test is available to check the big hvac superheat from the driver seat. This test is controlled by multiplex, eliminating interventions and the need to take measures on the vehicle.
  • SR19-31C - EQUIPMENT: Engine control module (ecm) software update - engine cooling strategy in high altitude operation revision c: vin range in application box rearranged for h3 coaches
  • MI21-06 - FUEL SYSTEM, DIESEL: Diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair ⿿ from us10 to newer engine generation
  • SP18-35F - POWER TRAIN: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency rev e: expiration date removed
  • Mi21-07A - WHEELS: Ront & tag axle ⿿ unitized hub bearing end play verification and replacement
  • is_20089 - LATCHES/LOCKS/LINKAGES: Lavatory compartment sliding door latch improvement
  • IS-18042 - ELECTRICAL SYSTEM: Eberspacher preheater installation in replacement of spheros & valeo preheaters
  • MI20-08C - STRUCTURE: Storage and startup guidelines: periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, prevost recommends foll
  • IS-20925A - POWER TRAIN: Central hvac merv filters installation reva
  • IS-20932A - EQUIPMENT: H3 series envirocare - ions air sanitizer rev a
  • VBC-PREVOST 4 - EQUIPMENT ADAPTIVE/MOBILITY:VEHICLE CONTROLS:BRAKING: Communication letter from accociate administration for enforcement, nhtsa from prevost subject vehicle brand: prevost (ewr#000650)
  • IS-20932 - EQUIPMENT: H3 series envirocare - ions air sanitizer
  • IS-18091A - STEERING: Tie rod 610052 first installation instructions: use these instructions when replacing the drop joint tie rod on s82, s84 / s84u i-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment ne
  • MI20-19B - ENGINE AND ENGINE COOLING: Introducing a new engine coolant into prevost service center network
  • MI20-19A - ENGINE AND ENGINE COOLING: Rev a: mention added concerning ddc series 60 engine sca requirement
  • MI21-01 - EQUIPMENT: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI21-01 - POWER TRAIN: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • SP18-39C - FUEL SYSTEM, DIESEL: Scr converter replacement - aftertreatment system revision: c expiration date removed 12/22/2020
  • SP18-35E - FUEL SYSTEM, DIESEL: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency rev e: expiration date removed
  • MI20-19 - EQUIPMENT: Introducing a new engine coolant into service
  • MI02-17A - EQUIPMENT ADAPTIVE/MOBILITY: Revision : a torque value reduced
  • MI18-02A - ENGINE AND ENGINE COOLING: Engine oil & filter change intervals - volvo d13 engine, from us10 revision: a updated for obd20 engines
  • IS-19165A - ELECTRICAL SYSTEM: Lavatory fan retrofit kit applicable for h3 series coaches from r-1012 (1994) revision a: added installation detail at step 8
  • IS-13169A - BACK OVER PREVENTION: SENSING SYSTEM: RADAR: Prevost aware adaptive cruise braking (acb) flr20 radar sensor replacement kit revision a: kit is13169-1 & is13169-2 canceled, use 145373 &145372
  • MI20-14 - VISIBILITY: Prevost driver assistâ¿¢ - windshield replacement equipped with camera
  • IS-20923 - EQUIPMENT: H3 driver⿿s partition lite installation
  • IS-20929 - EQUIPMENT: Uv lights installation in ac compartment
  • IS-20929 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Uv lights installation in a/c compartment
  • P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • U17_P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • MI20-08B - EQUIPMENT: Storage and startup guidelines revision: b parts added to suggested material 08-10-2020
  • IS-20922 - EQUIPMENT ADAPTIVE/MOBILITY: Sigma passenger seats partition kit
  • MI18-18B - EQUIPMENT: General hoisting and towing procedures revision: b updated 2.1 to show rubber chocks, secure front and rear.
  • MI20-12 - STEERING: Jerky, noisy or hard to turn steering gearbox. Hydraulic end limiter adjustment. All models ⿿ equipped with rb bosch/zf servocom or servocomtronic steering gearbox
  • IS-09900i - EQUIPMENT ADAPTIVE/MOBILITY: Electric fan drive cooling system conversion with bosch alternator revision i: parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal, st,16
  • IS-19910H - ENGINE (PWS): Electric fan drive cooling system conversion with delco remy alternator revision h: parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal,
  • IS-20906 - EQUIPMENT ADAPTIVE/MOBILITY: Plexiglass shield behind driver h3 series
  • MI20-08A - EQUIPMENT: Storage and startup guidelines: rev a: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
  • MI20-09 - EQUIPMENT: Prevost vehicle disinfection procedure revision a
  • IS-19084 - EQUIPMENT: Accessory air filter replacement replaces 642192
  • U17_P040200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • U02A200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes U02A200 lost communication with reductant quality module
  • U029E00 - ENGINE (PWS): Repair instructions to address fault codes U029E00 lost communication with nox sensor "b"
  • U029D00 - ENGINE (PWS): Repair instructions to address fault codes U029D00 lost communication with nox sensor "a"
  • P256000 - EQUIPMENT: Repair instructions to address fault codes P256000 engine coolant level low
  • P242A15 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P242A15 exhaust gas temperature sensor bank 1 sensor 3 - circuit short to battery or open
  • P20E892 - EQUIPMENT: Repair instructions to address fault codes P20E892 reductant pressure too low - performance orincorrect operation
  • P208464 - EQUIPMENT: Repair instructions to address fault codes P208464 exhaust gas temperature sensor circuit range/performance bank 1 sensor 2 - signal plausibility failure
  • P204A13 - EQUIPMENT: Repair instructions to address fault codes P204A13 reductant pressure sensor - circuit open
  • P204713 - EQUIPMENT: Repair instructions to address fault codes P204713 reductant injection valve control bank 1 unit 1 ⿿ circuit open
  • P203F00 - EQUIPMENT: Repair instructions to address fault codes P203F00 reductant level low
  • P203115 - EQUIPMENT: Repair instructions to address fault codes P203115 exhaust gas temperature sensor bank 1 sensor 2 - circuit short to battery or open
  • P10CE97 - EQUIPMENT: Repair instructions to address fault codes P10CE97 reductant return: no flow detected - componentor system operation obstructed or blocked
  • P107575 - EQUIPMENT: Repair instructions to address fault codes P107575 clutch system - emergency position not reachable
  • P107017 - BRAKES (PWS): Repair instructions to address fault codes P107017 gearbox brake valve (vagb) - circuit voltage above threshold
  • P105998 - POWER TRAIN: Repair instructions to address fault codes P105998 gearbox oil temperature sensor - component orsystem over temperature
  • P054415 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P054415 exhaust gas temperature sensor bank 1 sensor 1 - circuit short to battery or open
  • P052400 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P052400 engine oil pressure too low
  • P040200 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • P029800 - ENGINE (PWS): Repair instructions to address fault codes P029800
  • P021700 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P021700 engine coolant over temperature condition
  • NOx_Conv2 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P207F-00; P20EE-00
  • NOX_Conv1 - EQUIPMENT ADAPTIVE/MOBILITY: Repair instructions to address fault codes P207F-00 - reductant quality
  • FUELFILTER - ENGINE (PWS): Repair instructions to address fault codes P008A-00; P0087-00
  • MI20-09 - EQUIPMENT:OTHER:LABELS: Prevost vehicle disinfection procedure
  • MI20-08 - UNKNOWN OR OTHER: Storage and startup guidelines - all prevost vehicles & volvo 9700
  • IS-20905 - EQUIPMENT: Hand sanitizer dispenser installation
  • IS-19064 - STRUCTURE: Baggage door seal replacement
  • MI15-24 - EQUIPMENT ADAPTIVE/MOBILITY: Added: power cables for l.H. Side alternator & fan drive breaker box
  • IS-14076 - EQUIPMENT: This instruction sheets explains how to replace the fuel tank on h-series vehicles. (replacing older series tanks by newer model)
  • IS-19910G - ENGINE AND ENGINE COOLING: Revision : mention added stating to disable prime.
  • IS-19900H - ENGINE AND ENGINE COOLING: Revision : mention added in the instruction sheet stating to disable "prime"
  • IS-19921A - EQUIPMENT: This instruction sheet explains how to install a seatbelt cutter in the driver's area
  • IS-19066 - SERVICE BRAKES, AIR: This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
  • SCI19-01C - ELECTRICAL SYSTEM: The intent of this procedure is to guide you through the steps required to program a mcm especially for the control of the electric fan drive as required for conversion kit of instruction sheets is-19900, is-19901, is19910, is-19912.
  • IS-19900G - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric fan drive cooling system conversion kit with bosch alternator - h3 series us10 cooling system
  • IS-19043 - EQUIPMENT: This instruction sheet explains how to relocate the wheel chair lift parcel rack fan
  • IS-17151 - LIGHTING (PWS): This instruction sheet explains how to replace halogen fog light to led's
  • IS-19910E - ELECTRICAL SYSTEM: This instruction sheet explains how to perform an electric fan drive cooling system conversion with delco remy alternator - h3 series us10 to ghg17 included
  • SP18-35D_English - FUEL SYSTEM, DIESEL: On vehicles with active code P20EE, perform the following checklist and operations.
  • IS-19910D - ELECTRICAL SYSTEM: This instruction sheet explains how to perform an electric fan drive cooling system conversion with delco remy alternator - h3 series us10 to ghg17 included
  • IS-19900E - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric fan drive cooling system conversion kit with bosch alternator - h3 series us10 cooling system
  • IS-18091 - STEERING: This instruction sheet explains how to perform the first installation of tie rod 610052 on prevost vehicles equipped with dana s82, s84 / s84u i-beam axles, 1994- today
  • MI18-45A - POWER TRAIN: Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to is-18091 for installation instruction
  • Mi14-34D - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: Prevost aware adaptive cruise braking (acb) - flr20 & flr21 radar sensor alignment
  • IS-19915 - EQUIPMENT: Mp-1000 multimedia player installation
  • IS-19911C - EQUIPMENT: Intelligent sleep mode installation
  • IS-19900D - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with bosch alternator - h3 series us10 cooling system
  • IS-18910 - EQUIPMENT: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-18091 - SUSPENSION: This instruction sheet explains how to install the tie rod 610052.
  • IS-17900A - STRUCTURE: Wheel fender stainless steel protector
  • CK19-16 - SEAT BELTS:FRONT:WARNING LIGHT/DEVICES: Isri seat belt with sensor installation (accessory kit 23687694)
  • WB19-07 - SERVICE BRAKES, AIR: On the independent front suspension (ifs) of the vehicles affected by this bulletin, check and make sure that there is enough clearance between the brake hoses identified in the procedure and their respective support bracket.
  • SP18-35C_English - ENGINE AND ENGINE COOLING: On vehicles with active code P20EE, perform the following checklist and operations.
  • IS-19908E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on h3 vehicles
  • IS-19905D - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to install delco remy alternators on h3 vehicles equipped with electric fan drive
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet shows how to install a flap over the diesel filling cap.
  • WB19-02A - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin replace the idler and belt tensioner support on the left side (hot side) of the engine by an improved part, 011213. This applies to installations with bosch or delco remy alternators on the hot side
  • IS-19900A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to convert h3 series us10 vehicles equipped with bosch alternators to electric fan drive (efd) cooling system
  • SP18-35B_English - ENGINE (PWS): On vehicles with active code P20EE, perform the following checklist and operations.
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet explains how to install a flap over the diesel filling cap
  • IS-18115 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to install a gm glove box lock on h-series vehicles
  • IS-17071A - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • SP18-39B - ENGINE (PWS): This special bulletin explains how to perform the replacement of the scr tank, when authorized.
  • SCI19-01A - ELECTRICAL SYSTEM: This procedure explains how to program a mcm especially for the control of the electric fan drive, as required for conversion kit of instruction sheets is-19900 & is-19910.
  • MI19-06 - BRAKES (PWS): This maintenance information is published to answer some questions regarding the inverted or ?Trailing? Mounting position of the drive axle brake calipers on prevost vehicles
  • MI19-05 - EQUIPMENT: This maintenance information expains how to adjust p/n 660865, 660699 draglinks
  • IS-19911B - EQUIPMENT: This instruction sheet explains how to install ism (intelligent sleep mode) - on h series with prime hardware
  • IS-19900 - ENGINE AND ENGINE COOLING: This instruction sheet explains how to convert h3 series us10 vehicles equipped with bosch alternators to electric fan drive (efd) cooling system
  • IS-15075 - STRUCTURE: This instruction sheet explains how to replace fenders made of fiber glass with aluminium
  • SCI19-01 - EQUIPMENT: This procedure explains how to program a mcm especially for the control of the electric fan drive, as required for conversion kit of instruction sheets is-19900 & is-19910.
  • Sp18-39A - ENGINE AND ENGINE COOLING: This special bulletin explains how to perform the replacement of the scr tank, when authorized.
  • SCI18-46 - EQUIPMENT:ELECTRICAL: This service center instructions explains how to install the prevost ultimate entertainment system
  • IS-18905 - EQUIPMENT: This instruction sheet explains how to install hatches with fan on h3 vehicles.
  • WB18-43 - POWER TRAIN: This warranty bulletin explains how to update the vecu (vehicle electronic control unit) parameters to allow auto engine brake function with the i-shift transmission.
  • SP18-39 - EQUIPMENT: This special bulletin explains how to perform the replacement of the scr tank, when authorized.
  • Sp18-35 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : On vehicles with active code P20EE, perform the following checklist and operations.
  • WB18-04 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available.
  • MI18-37 - POWER TRAIN:AUTOMATIC TRANSMISSION: This maintenance information presents information about the removal or installation of the lang kk73.1 electromagnetic clutch - part of the bitzer (model 4nfcy) air conditioning compressor.
  • MI18-21A - ENGINE AND ENGINE COOLING: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-18A - EQUIPMENT: This maintenance information explains how to tow and hoist prevost vehicles.
  • WB18-01A - STRUCTURE: On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
  • WB18-07B - EQUIPMENT: On the vehicles affected by this bulletin, the busbar connected to circuit breaker cb13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper inst
  • SP18-24 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, add belleville washers on the leveling screws of the front right slide-out
  • MI18-18 - EQUIPMENT:MECHANICAL:WRECKER AND WHEEL LIFT DEVICES: This maintenance information explains how to tow and hoist prevost vehicles.
  • MI18-22 - EQUIPMENT:ELECTRICAL: This maintenance information presents information about the eld installation and parameter list on prevost coaches
  • MI18-21 - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-16A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information presents guidelines to help with the diagnosis of the bosch hd10 alternators
  • IS-18902 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to installa parcel rack door kits
  • WB18-07 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the busbar connected to circuit breaker cb13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper inst
  • IS-17905 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-13009B - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install and adjust drag link # 660699
  • WB18-07A - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the busbar connected to circuit breaker cb13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper inst
  • MI18-02 - ENGINE AND ENGINE COOLING: This mainteannce informaiton presents the latest engine oil & filter change intervals for the volvo engine
  • IS-17907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the volvo electronic logging device (eld)
  • IS-17071 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • Wb18-01 - LATCHES/LOCKS/LINKAGES:DOORS:LATCH: On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
  • MI17-22 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: This maintenance information explains how to inspect the fuel tank cradle mounting screws on a yearly basis
  • CK17-30 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is now possible to replace the older generation tgw 2.0 (3g network) by the newer 2.1 version (4g the network) using accessory kit 23266301 and the following procedure.
  • Sp17-29 - POWER TRAIN:AUTOMATIC TRANSMISSION: On the vehciles affected by this bulletin, perform a multiplex software update to correct unwanted behavior of the cruise control. The affected vehicles are equipped with a transmission retarder.
  • CK17-27 - EQUIPMENT ADAPTIVE/MOBILITY: This conversion kit explains how to to disable the acb radar.
  • WB17-08 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin check tightening on both ifss extinguisher head screws. If screws are loosened, tighten to the torque value specified.
  • CK17-26 - ENGINE (PWS): On the vehicles affected by this bulletin, it is now possible to disable the engine brake automatic function by running accessory kit # 23181730.
Known Recall Investigations
  • Alternator front bearing failure investigation # PE21011

    Nhtsas office of defects investigation (odi) is opening a preliminary evaluation after receiving a tip from a fleet safety manager concerning alternator front bearing failures that cause elevated temperatures within the engine compartment, resulting in the fire suppression system (fss) activating, immediately shutting the engine down, and rendering the bus inoperable. Review of early warning reporting data identified 9 field reports for model year (my)2015 through my2019 h3 and x3 prevost buses, describing alternator failures in any of 3 alternators equipped on the bus. In some cases, a minor fire occurred damaging nearby electrical harnesses. An immediate shut down of the bus can increase the risk of a crash or injury of passengers when transferring to another bus.Odi is opening this investigation to evaluate the cause, consequence, scope and frequency of the alleged defect in the subject prevost buses.

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.