Prevost H3-45 Vip 2019

Vehicle Details: Recalls, Investigations, Service Bulletins

Below you will find all available information on the 2019 PREVOST H3-45 Vip.

ManufacturerKnown WMI(s)Fuel Type
PREVOST
PREVOST VIN Decoder

Use the box here to look up VINs from PREVOST as well as other manufacturers

#
Frequently Asked Questions
  • Are there recalls for the 2019 PREVOST H3-45 Vip?
     - There are 5 recall(s) for the 2019 PREVOST H3-45 Vip, additional information is below.
NHTSA Mandated Recalls
  • Recall 260248 [USA]: Beacons that do not provide proper illumination may be less visible to wheelchair lift users, increasing the risk of injury.

  • Recall 240603 [USA]: The activation of the automatic fire suppression system can cause a sudden loss of drive power, increasing the risk of a crash. additionally, a disabled coach may require an evacuation procedure in an uncontrolled traffic situation, increasing the risk of injury to passengers.

  • Recall 192034 [USA]: An overheated alternator bearing can increase the risk of a fire.

  • Recall 188012 [USA]: A damaged circuit board increases the risk of a fire.

  • Recall 147412 [USA]: If the engine unexpectedly shuts down, passengers may have to be transferred to another vehicle on the side of the road, increasing the risk of an injury. if the engine unexpectedly shuts down while the vehicle is in motion, there is an increased risk of crash.

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • IS-23019 - SUSPENSION: Sway bar collars improvement
  • IS-22106 - EQUIPMENT: H3 lavatory fan retrofit kit
  • IS-18106 - STEERING: Kit power steering tank convertion cummins to zf with d13 engine
  • IS-21072B - ELECTRICAL SYSTEM: Steering gateway. Revision b - pin 2 and 10 were inverted on connector a139
  • MI22-12B - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: b - general update
  • IS-22055 - EXTERIOR LIGHTING: H3 series led headlamps retrofit
  • SP18-35J - ENGINE AND ENGINE COOLING: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency. Revision j - range of applicable vins updated.
  • MI22-12A - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: a - erroneous secondary & accessory tanks location.
  • MI22-12 - SERVICE BRAKES, AIR: Air tanks draining sequence
  • IS-17151C - EXTERIOR LIGHTING: Halogen to led fog light replacement kit. Revision: c - advanced kits canceled
  • SP18-35J - ENGINE AND ENGINE COOLING: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency. Revision j - range of applicable vins updated.
  • IS-22902 - WHEELS: Tag axle hub flange - alternate cap screw
  • IS21-072 - ELECTRICAL SYSTEM: Steering gateway, revision a : cancel watch dog removal from efd part of the instruction
  • MI20-08C - EQUIPMENT: Storage and startup guidelines : part number updates
  • WB22-07 - ELECTRICAL SYSTEM: Tgw programming
  • IS21-072A - ELECTRICAL SYSTEM: Steering gateway revision a cancel watch dog removal from efd part of the instruction
  • IS20-925A - VISIBILITY: Central hvac merv filters installation
  • IS20-932A - EQUIPMENT: H3 series envirocare - ions air sanitizer
  • IS22-040 - EQUIPMENT ADAPTIVE/MOBILITY: Brake pedal seal plate installation kit
  • IS21-072 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Steering gateway schematic
  • SP18-35H - EQUIPMENT: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • SP18-35H - EQUIPMENT ADAPTIVE/MOBILITY: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • SP18-39D - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Scr converter replacement - aftertreatment system
  • SP18-35H - EQUIPMENT:MECHANICAL: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • SP18-35H - POWER TRAIN: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • MI21-13A - EQUIPMENT: An automated test is available to check the big hvac superheat from the driver seat. This test is controlled by multiplex, eliminating interventions and the need to take measures on the vehicle.
  • SR19-31C - EQUIPMENT: Engine control module (ecm) software update - engine cooling strategy in high altitude operation revision c: vin range in application box rearranged for h3 coaches
  • MI21-06 - FUEL SYSTEM, DIESEL: Diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair ⿿ from us10 to newer engine generation
  • SP18-35F - POWER TRAIN: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency rev e: expiration date removed
  • Mi21-07A - WHEELS: Ront & tag axle ⿿ unitized hub bearing end play verification and replacement
  • is_20089 - LATCHES/LOCKS/LINKAGES: Lavatory compartment sliding door latch improvement
  • IS-18042 - ELECTRICAL SYSTEM: Eberspacher preheater installation in replacement of spheros & valeo preheaters
  • MI20-13A - VISIBILITY: Side camera rear view system ⿿ camera adjustment ⿿ h3 & x3 series
  • IS-19037B - EQUIPMENT ADAPTIVE/MOBILITY: Prevost driver assist system camera & head-up-display installation on h3 series
  • MI20-08C - STRUCTURE: Storage and startup guidelines: periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, prevost recommends foll
  • IS-20925A - POWER TRAIN: Central hvac merv filters installation reva
  • IS-20932A - EQUIPMENT: H3 series envirocare - ions air sanitizer rev a
  • VBC-PREVOST 4 - EQUIPMENT ADAPTIVE/MOBILITY:VEHICLE CONTROLS:BRAKING: Communication letter from accociate administration for enforcement, nhtsa from prevost subject vehicle brand: prevost (ewr#000650)
  • is_20073 - EQUIPMENT: Flush floor slide-out position sensor magnet support replacement
  • is_19037a - EQUIPMENT: Prevost driver assist system camera & head-up-display installation on h3 series
  • IS-20932 - EQUIPMENT: H3 series envirocare - ions air sanitizer
  • IS-19037 - EQUIPMENT: Prevost driver assist system camera & head-up-display installation on h3 series
  • IS-18091A - STEERING: Tie rod 610052 first installation instructions: use these instructions when replacing the drop joint tie rod on s82, s84 / s84u i-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment ne
  • MI20-19B - ENGINE AND ENGINE COOLING: Introducing a new engine coolant into prevost service center network
  • MI20-19A - ENGINE AND ENGINE COOLING: Rev a: mention added concerning ddc series 60 engine sca requirement
  • MI21-01 - EQUIPMENT: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI21-01 - POWER TRAIN: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • SP18-39C - FUEL SYSTEM, DIESEL: Scr converter replacement - aftertreatment system revision: c expiration date removed 12/22/2020
  • SP18-35E - FUEL SYSTEM, DIESEL: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency rev e: expiration date removed
  • MI20-19 - EQUIPMENT: Introducing a new engine coolant into service
  • MI02-17A - EQUIPMENT ADAPTIVE/MOBILITY: Revision : a torque value reduced
  • PCN2017151 - VISIBILITY: The halogen fog lights have been replaced by led lights. Installation of the new lights is different. New supports to enable the beam to be adjusted with a screw when the bumper is closed (due to the precision required to perform the adjus
  • MI18-02A - ENGINE AND ENGINE COOLING: Engine oil & filter change intervals - volvo d13 engine, from us10 revision: a updated for obd20 engines
  • IS-19165A - ELECTRICAL SYSTEM: Lavatory fan retrofit kit applicable for h3 series coaches from r-1012 (1994) revision a: added installation detail at step 8
  • IS-13169A - BACK OVER PREVENTION: SENSING SYSTEM: RADAR: Prevost aware adaptive cruise braking (acb) flr20 radar sensor replacement kit revision a: kit is13169-1 & is13169-2 canceled, use 145373 &145372
  • MI20-14 - VISIBILITY: Prevost driver assistâ¿¢ - windshield replacement equipped with camera
  • IS-20923 - EQUIPMENT: H3 driver⿿s partition lite installation
  • IS-20929 - EQUIPMENT: Uv lights installation in ac compartment
  • IS-20929 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Uv lights installation in a/c compartment
  • MI20-13 - ELECTRICAL SYSTEM:ADAS:DRIVER MONITORING:CAMERA/SENSOR: Emirror side camera system adjustment
  • P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • U17_P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • MI20-08B - EQUIPMENT: Storage and startup guidelines revision: b parts added to suggested material 08-10-2020
  • IS-20922 - EQUIPMENT ADAPTIVE/MOBILITY: Sigma passenger seats partition kit
  • MI18-18B - EQUIPMENT: General hoisting and towing procedures revision: b updated 2.1 to show rubber chocks, secure front and rear.
  • MI20-12 - STEERING: Jerky, noisy or hard to turn steering gearbox. Hydraulic end limiter adjustment. All models ⿿ equipped with rb bosch/zf servocom or servocomtronic steering gearbox
  • IS-20906 - EQUIPMENT ADAPTIVE/MOBILITY: Plexiglass shield behind driver h3 series
  • MI20-08A - EQUIPMENT: Storage and startup guidelines: rev a: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
  • IS-19905F - ELECTRICAL SYSTEM: Bosch to delco remy alternator installation, h3-45 with electric fan drive; revision f updated alttyp parameter value name.
  • MI20-09 - EQUIPMENT: Prevost vehicle disinfection procedure revision a
  • IS-19084 - EQUIPMENT: Accessory air filter replacement replaces 642192
  • U17_P040200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • U02A200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes U02A200 lost communication with reductant quality module
  • U029E00 - ENGINE (PWS): Repair instructions to address fault codes U029E00 lost communication with nox sensor "b"
  • U029D00 - ENGINE (PWS): Repair instructions to address fault codes U029D00 lost communication with nox sensor "a"
  • P256000 - EQUIPMENT: Repair instructions to address fault codes P256000 engine coolant level low
  • P242A15 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P242A15 exhaust gas temperature sensor bank 1 sensor 3 - circuit short to battery or open
  • P20E892 - EQUIPMENT: Repair instructions to address fault codes P20E892 reductant pressure too low - performance orincorrect operation
  • P208464 - EQUIPMENT: Repair instructions to address fault codes P208464 exhaust gas temperature sensor circuit range/performance bank 1 sensor 2 - signal plausibility failure
  • P204A13 - EQUIPMENT: Repair instructions to address fault codes P204A13 reductant pressure sensor - circuit open
  • P204713 - EQUIPMENT: Repair instructions to address fault codes P204713 reductant injection valve control bank 1 unit 1 ⿿ circuit open
  • P203F00 - EQUIPMENT: Repair instructions to address fault codes P203F00 reductant level low
  • P203115 - EQUIPMENT: Repair instructions to address fault codes P203115 exhaust gas temperature sensor bank 1 sensor 2 - circuit short to battery or open
  • P10CE97 - EQUIPMENT: Repair instructions to address fault codes P10CE97 reductant return: no flow detected - componentor system operation obstructed or blocked
  • P107575 - EQUIPMENT: Repair instructions to address fault codes P107575 clutch system - emergency position not reachable
  • P107017 - BRAKES (PWS): Repair instructions to address fault codes P107017 gearbox brake valve (vagb) - circuit voltage above threshold
  • P105998 - POWER TRAIN: Repair instructions to address fault codes P105998 gearbox oil temperature sensor - component orsystem over temperature
  • P054415 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P054415 exhaust gas temperature sensor bank 1 sensor 1 - circuit short to battery or open
  • P052400 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P052400 engine oil pressure too low
  • P040200 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • P029800 - ENGINE (PWS): Repair instructions to address fault codes P029800
  • P021700 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P021700 engine coolant over temperature condition
  • NOx_Conv2 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P207F-00; P20EE-00
  • NOX_Conv1 - EQUIPMENT ADAPTIVE/MOBILITY: Repair instructions to address fault codes P207F-00 - reductant quality
  • FUELFILTER - ENGINE (PWS): Repair instructions to address fault codes P008A-00; P0087-00
  • MI20-09 - EQUIPMENT:OTHER:LABELS: Prevost vehicle disinfection procedure
  • MI20-08 - UNKNOWN OR OTHER: Storage and startup guidelines - all prevost vehicles & volvo 9700
  • IS-20905 - EQUIPMENT: Hand sanitizer dispenser installation
  • IS-19064 - STRUCTURE: Baggage door seal replacement
  • MI15-24 - EQUIPMENT ADAPTIVE/MOBILITY: Added: power cables for l.H. Side alternator & fan drive breaker box
  • IS-14076 - EQUIPMENT: This instruction sheets explains how to replace the fuel tank on h-series vehicles. (replacing older series tanks by newer model)
  • IS-19921A - EQUIPMENT: This instruction sheet explains how to install a seatbelt cutter in the driver's area
  • IS-19066 - SERVICE BRAKES, AIR: This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
  • IS-19043 - EQUIPMENT: This instruction sheet explains how to relocate the wheel chair lift parcel rack fan
  • IS-17151 - LIGHTING (PWS): This instruction sheet explains how to replace halogen fog light to led's
  • Sp19-35 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, a modification of the small a/c compressor harness is necessary.
  • SP18-35D_English - FUEL SYSTEM, DIESEL: On vehicles with active code P20EE, perform the following checklist and operations.
  • MI19-27A - STRUCTURE: This maintenance information explains how to perform the installation of two-part slide-out seals with clip-on inflatable seal.
  • IS-18091 - STEERING: This instruction sheet explains how to perform the first installation of tie rod 610052 on prevost vehicles equipped with dana s82, s84 / s84u i-beam axles, 1994- today
  • IS-16078 - EQUIPMENT: This instruction sheet explains how to add drain holes in the weiler slide-out base seal
  • Wb19-11 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the vehicle program might need to be upgraded to prevent batteries drain when ism (intelligent sleep mode) is enabled.
  • MI18-45A - POWER TRAIN: Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to is-18091 for installation instruction
  • Mi14-34D - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: Prevost aware adaptive cruise braking (acb) - flr20 & flr21 radar sensor alignment
  • IS-19915 - EQUIPMENT: Mp-1000 multimedia player installation
  • IS-19911C - EQUIPMENT: Intelligent sleep mode installation
  • IS-18910 - EQUIPMENT: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-18091 - SUSPENSION: This instruction sheet explains how to install the tie rod 610052.
  • IS-17900A - STRUCTURE: Wheel fender stainless steel protector
  • CK19-16 - SEAT BELTS:FRONT:WARNING LIGHT/DEVICES: Isri seat belt with sensor installation (accessory kit 23687694)
  • SCI19-21 - VISIBILITY: This document shows how to install exterior perimeter cameras and interior cameras. It also shows how to make the setup with the monitor
  • WB19-07 - SERVICE BRAKES, AIR: On the independent front suspension (ifs) of the vehicles affected by this bulletin, check and make sure that there is enough clearance between the brake hoses identified in the procedure and their respective support bracket.
  • SP18-35C_English - ENGINE AND ENGINE COOLING: On vehicles with active code P20EE, perform the following checklist and operations.
  • SP19-15A - VISIBILITY: On the vehicles affected by this bulletin, the brigade camera system parameters must be set up and the system rebooted to enable activation.
  • IS-19905D - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to install delco remy alternators on h3 vehicles equipped with electric fan drive
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet shows how to install a flap over the diesel filling cap.
  • WB19-02A - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin replace the idler and belt tensioner support on the left side (hot side) of the engine by an improved part, 011213. This applies to installations with bosch or delco remy alternators on the hot side
  • SP19-15 - VISIBILITY: On the vehicles affected by this bulletin, the brigade camera system parameters must be set up and the system rebooted to enable activation.
  • IS-19905C - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to install delco remy alternators on h3 vehicles equipped with efd (electric fan drive)
  • IS-16078 - STRUCTURE: This instruction sheet explains how to add drain holes in weiler slide-out base seal
  • SP18-35B_English - ENGINE (PWS): On vehicles with active code P20EE, perform the following checklist and operations.
  • SCI18-47 - STRUCTURE: This instruction sheet explains how to adjust the slide out room laterally in the frame opening, front and rear from a vehicle standpoint.
  • IS-19905 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to install delco remy alternators on h3 vehicles equipped with efd
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet explains how to install a flap over the diesel filling cap
  • IS-18115 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to install a gm glove box lock on h-series vehicles
  • IS-16080 - EQUIPMENT: This instruction sheet explains how to add drain holes in the slide-out base seal
  • SP18-49A - STEERING:COLUMN: On the vehicles affected by this bulletin, an inspection of the upper steering column universal joint must be performed.
  • SP18-39B - ENGINE (PWS): This special bulletin explains how to perform the replacement of the scr tank, when authorized.
  • MI19-06 - BRAKES (PWS): This maintenance information is published to answer some questions regarding the inverted or ?Trailing? Mounting position of the drive axle brake calipers on prevost vehicles
  • MI19-05 - EQUIPMENT: This maintenance information expains how to adjust p/n 660865, 660699 draglinks
  • IS-19905 - EQUIPMENT: This instruction sheet explains how to install delco remy alternators on h3 vehicles equipped with efd
  • Sp18-39A - ENGINE AND ENGINE COOLING: This special bulletin explains how to perform the replacement of the scr tank, when authorized.
  • SCI18-46 - EQUIPMENT:ELECTRICAL: This service center instructions explains how to install the prevost ultimate entertainment system
  • SP18-49 - STEERING: On the vehicles affected by this bulletin, an inspection of the upper steering column universal joint must be performed.
  • MI18-45 - EQUIPMENT: This maintenance information presents the new maintenance inspections and new method to adjust toe-in of vehicles equipped with new tie rod 610052.
  • IS-18905 - EQUIPMENT: This instruction sheet explains how to install hatches with fan on h3 vehicles.
  • WB18-43 - POWER TRAIN: This warranty bulletin explains how to update the vecu (vehicle electronic control unit) parameters to allow auto engine brake function with the i-shift transmission.
  • SP18-39 - EQUIPMENT: This special bulletin explains how to perform the replacement of the scr tank, when authorized.
  • Sp18-35 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : On vehicles with active code P20EE, perform the following checklist and operations.
  • WB18-04 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available.
Known Recall Investigations
  • Alternator front bearing failure investigation # PE21011

    Nhtsas office of defects investigation (odi) is opening a preliminary evaluation after receiving a tip from a fleet safety manager concerning alternator front bearing failures that cause elevated temperatures within the engine compartment, resulting in the fire suppression system (fss) activating, immediately shutting the engine down, and rendering the bus inoperable. Review of early warning reporting data identified 9 field reports for model year (my)2015 through my2019 h3 and x3 prevost buses, describing alternator failures in any of 3 alternators equipped on the bus. In some cases, a minor fire occurred damaging nearby electrical harnesses. An immediate shut down of the bus can increase the risk of a crash or injury of passengers when transferring to another bus.Odi is opening this investigation to evaluate the cause, consequence, scope and frequency of the alleged defect in the subject prevost buses.

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.