PI0281K

Bulletin No.: PI0281K
Date: Jan-2024
Subject:
Underbody Component Corrosion
Models:
2024 and Prior GM Passenger Cars and Trucks (Excluding Medium Duty Low Cab Forward)
Attention:
This PI also applies to any of the above models that may be Export from North America vehicles.
This PI has been revised to add the 2024 Model Year and Important Statement. Please discard PI0281J.
Important: Service agents must comply with all International, Federal, State, Provincial, and/or Local laws applicable to the activities it performs
under this bulletin, including but not limited to handling, deploying, preparing, classifying, packaging, marking, labeling, and shipping
dangerous goods. In the event of a conflict between the procedures set forth in this bulletin and the laws that apply to your dealership, you must
follow those applicable laws.
The following information may be helpful when addressing underbody component corrosion with customers.
Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion.
This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron.
This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Note: Extended outside storage may increase the opportunity for brake rotor rust. Vehicle braking systems tend to be self-cleaning while vehicles are in use,
preventing any build-up of corrosion on the brake rotor surfaces. At times more extensive corrosion can cause pulsation due to thickness variation. This usually
happens when the vehicle is parked for long periods of time in humid type conditions and the braking surface area under the pads corrode at a different rate
compared to the rest of the braking surface area. Cleaning up of braking surfaces (burnishing) can be accomplished by 10-15 moderate stops from 5664♦km/h (35-40♦mph) with cooling time between stops. If multiple, moderate braking stops do not correct this condition, refer to the following Service Bulletins
for additional information:
– Latest version of Corporate Bulletin Number 00-05-22-002: Disc Brake Warranty Service and Procedures
– Bulletin # 22-NA-026: Information on Brake Pulsation, Noise and/or Visible Pitting Condition to Brake Rotor Surface
– Bulletin # 17-NA-239: Information on Normal Characteristic - Vehicle Unable to Move After Being Parked for an Extended Period of Time
Corrosion Protection
General Motors uses a large variety of materials in the manufacture of vehicles. Many of these components undergo an extensive corrosion protection
process. These components include major body structures, powertrain, wiring and electrical components and various other areas of the vehicle. General
Motors engineering determines the effects of corrosion on every vehicle component.
Acceptable Corrosion
General Motors has determined that the performance of some components is not affected by surface corrosion and no longer takes preventative steps on
these parts.
Rust
This corrosion may be red or brown in appearance if the component is made of steel, forged iron or cast iron.
These are typical underbody or mechanical components such as but not limited to propshafts, propshaft yokes, U-joint, steering knuckles, brake rotors and
calipers, axle housings, springs, shock absorbers, suspension control arms, tie rod ends and exhaust system components. As the rust ages, it turns from an
orange-red like appearance to a darker brown like appearance.
Aluminum Oxidation
Cast aluminum alloy components may appear to have a grey or white coating on the surface commonly known as “surface oxidation.” Uncoated aluminum alloys
begin to oxidize as soon as it is exposed to the atmosphere. This coating does not affect the serviceability or performance of the component.
1
Many mechanical components are cast in aluminum alloys, these components may include, but are not limited to oil pans, valve covers, transmission and
transfer case housings, steering gears and axle housings.
Typical Appearance
Front axle housing
Steering linkage
Steering knuckle
Tie rod end
2
Propshaft yoke
Leaf spring
Rear differential housing
Under hood components
3
Exhaust system components
Note: During transit between the plant and the dealer, some of the exhaust system components may corrode as a result of salt exposure. These exhaust parts
are made of a bare mild-grade stainless steel that will oxidize or appear rusty. Over time, these components will have a uniform rust-like discoloration, which
should be considered a normal condition.
Recommendation
No repair or consideration should be given for this condition. Surface corrosion on unprotected components will vary with age and exposure. Corrosion on
these components has no detrimental impacts, either in short or long-term durability.
GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may
occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools,
safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that
your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information.
WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION
4