19-AT-008G
Service Bulletin Details
Public Details for: 19-AT-008G
When servicing a vehicle with a a??Check engine lighta?? And any of the dtcs listed below, follow the service procedure to replace the related solenoid and e-module or park position switch.
- 2024 - 2023 - 2022 - 2021 - 2020 - 2019 -
Models from 2024
2024 GENESIS G70 |
2024 GENESIS G80 |
2024 GENESIS G90 |
Models from 2023
2023 GENESIS G70 |
2023 GENESIS G80 |
2023 GENESIS G90 |
Models from 2022
2022 GENESIS G70 |
2022 GENESIS G80 |
2022 GENESIS G90 |
Models from 2021
2021 GENESIS G70 |
2021 GENESIS G80 |
2021 GENESIS G90 |
Models from 2020
2020 GENESIS G70 |
2020 GENESIS G80 |
2020 GENESIS G90 |
Models from 2019
2019 GENESIS G70 |
2019 GENESIS G80 |
2019 GENESIS G90 |
GROUP NUMBER AUTOMATIC TRANSMISSION DATE Technical Service Bulletin SUBJECT: APRIL 2019 19-AT-008G MODEL(S) GENESIS G70 (IK) GENESIS G80 (DH) GENESIS G90 (HI) AUTOMATIC TRANSMISSION SOLENOID DTC P0741, P0743, P0748, P0753, P0758, P075A, P075D, P0763, P0768, P076A, P07B5, P076D, P0773, P0785, P078A, P0995 & P2709 Description: When servicing a vehicle with a “Check Engine light” and any of the DTCs listed below, follow the Service Procedure to replace the related solenoid and E-module or park position switch. Applicable Vehicles: 2019~ Genesis G70 (IK) with Shift-by Wire (SBW) 2019~ Genesis G80 (DH) with Shift-by-Wire (SBW) 2019~ Genesis G90 (HI) with Shift-by-Wire (SBW) DTC LIST WITH PART NUMBER INFORMATION: DTC DESCRIPTION PNC PART NO. P0741 P074100 Torque converter clutch circuit performance or stuck off 46202A 46313-3B01* P0743 P074300 Torque Converter Clutch Circuit Electrical (TC) 46202A 46313-3B01* P0748 P074800 Line Pressure Control Solenoid Valve A Electrical (LP) 46313A 46313-3B60* P0753 P075300 Shift Control Solenoid Valve A Electrical (UD) 46313 46313-4J10* P0758 P075800 Shift Control Solenoid Valve B Electrical (6) 46313 46313-4J10* P075A P075A00 ON/OFF Solenoid Circuit (Park – SBC) 46313D 46313-3B03* P075D P075D00 ON/OFF Solenoid D (PRH) – Electrical) 46313D 46313-3B03* P0763 P076300 Shift Control Solenoid Valve C Electrical (35R) 46313E 46313-4J20* P0768 P076800 Shift Control Solenoid D (4&OD) 46313E 46313-4J20* P076A P076A00 ON/OFF Solenoid C (Park - SBW) 46313D 46313-3B03* P076D P076D00 ON/OFF Solenoid C (Park - SBW) 46313D 46313-3B03* 46313 46313-4J10* P0785 P078500 ON/OFF Solenoid A (Drive – SBW) 46313D 46313-3B03* P078A P078A00 ON/OFF Solenoid B (Reverse – SBW) 46313D 46313-3B03* 46313 46313-4J10* 46305C 46305-4**** P0773 P077300 Shift Control Solenoid Valve E Electrical (27) P2709 P270900 Shift Control Solenoid Valve F Electrical (8LR) All All E-Module Circulate To: Service Manager, Warranty Manager, Service Advisors, Technicians, Fleet Repair SUBJECTATM SOLENOID DTC P0741, P0743, P0748, P0753, P0758, P075A, P075D, P0763, P0768, P076A, P07B5, P076D, P0773, P0785, P078A, P0995 & P2709 DTC LIST WITH PART NUMBER INFORMATION: DTC DESCRIPTION P076A P076A00 Park System Fault (SBW) P07B5 P07B500 Park Position Sensor Circuit Low P0995 P099500 Auto Shift Manual Mode Circuit (SBC) MODEL PNC PART NO. All 46235C 46340-4J10* 46756A 46756-***** All 42700E 42700-4J50* G80, G90 46700A 46700-***** G70 46700F 467W0-G92** WARRANTY INFORMATION: MODEL OP CODE OPERATION OP TIME CAUSAL PART NATURE CODE CAUSE CODE Genesis G70 (IK) Genesis G80 (DH) Genesis G90 (HI) 45775R8T Solenoid valve assy. Refer to WEBLTS for current LTS Refer to parts numbers in table above 13A ZZ3 42700R00 Park position switch Refer to WEBLTS for current LTS Refer to parts numbers in table above 13A ZZ3 Genesis G70 (IK) Genesis G80 (DH) Genesis G90 (HI) SERVICE PROCEDURE: 1. Attach a GDS and select DTC Analysis and A/T menu. Record the DTC and description. Delete the DTC. 2. From the GDS home screen, select Data Analysis and A/T menu and the solenoid parameters shown below. If the solenoids show: Continuous and changing output while driving, the wiring currently has no open/short circuits. Go to Step 4. No continuous and changing output, go to Step 3. TSB #: 19-AT-008G Page 2 of 12 SUBJECT: ATM SOLENOID DTC P0741, P0743, P0748, P0753, P0758, P075A, P075D, P0763, P0768, P076A, P07B5, P076D, P0773, P0785, P078A, P0995 & P2709 3. Visually check the wiring harness between the TCM and transmission for a damaged wire or connector. Check for an open/short circuit. If so, repair or replace the ECM control harness and drive the vehicle to confirm the repair. If no damage is found, go to Step 4. 4. Record the audio preset stations and disconnect the negative battery terminal. 5. Locate the harness connector on the passenger side of the transmission. Press the tab in the center of the latch and push the latch upward. Push the connector up to disconnect the connector from the valve body. To gain better access to the connector, place a support under the rear transmission support, loosen the bolts about ½ inch and lower the support about ½ inch. 6. Use an 8mm or 5/16” hex wrench and remove the fill plug. Torque: 17~18 lb.ft (2.3~2.5 kgf.m, 22~24 N.m) TSB #: 19-AT-008G Page 3 of 12 SUBJECTATM SOLENOID DTC P0741, P0743, P0748, P0753, P0758, P075A, P075D, P0763, P0768, P076A, P07B5, P076D, P0773, P0785, P078A, P0995 & P2709 7. Use an 8mm or 5/16” hex socket and remove the drain plug and drain the ATF. Reinstall the drain plug. Torque: 17~18 lb.ft (2.3~2.5 kgf.m, 22~24 N.m) 8. Remove 10 bolts that secure the valve body to the case and remove the valve body. Note the location of the 3 black bolts (shown with black arrow). If the valve body is stuck in the transmission, insert a screwdriver between the valve body and case and carefully pull the valve body out of the transmission. 9. Remove 9 bolts and remove the E-module. TSB #: 19-AT-008G Page 4 of 12 SUBJECT: ATM SOLENOID DTC P0741, P0743, P0748, P0753, P0758, P075A, P075D, P0763, P0768, P076A, P07B5, P076D, P0773, P0785, P078A, P0995 & P2709 10. Record the 8-digit code on the solenoid. 11. Refer to the solenoid DTC recorded in Step 1 and replace the related solenoid. DTC SOLENOID PNC P0753 UD 46313 P0768 4&OD 46313E P0763 35R 46313E P0773 27 46313 P0758 6 46313 P2709 8LR 46313 R 46313D P078A D 46313D P0785 P 36313D P076D P0743 TC 46202A P0748 LP 46313A 12. For UD, 4&OD, 35R, 27, 6 and 8LR solenoids: Remove one bolt and remove the solenoid support. TSB #: 19-AT-008G Page 5 of 12 SUBJECTATM SOLENOID DTC P0741, P0743, P0748, P0753, P0758, P075A, P075D, P0763, P0768, P076A, P07B5, P076D, P0773, P0785, P078A, P0995 & P2709 13. Use a magnet to remove the pin that secures the affected solenoid. Pull out the affected solenoid and install the new solenoid. Reinstall the pin. Reinstall the solenoid support using one bolt. 14. For R, D, P, TC and LP solenoids: Use a 5mm hex wrench or socket to remove 4 bolts that secure the support to the valve body and remove the support. 15. Pull out the related solenoid and install a new solenoid. Reinstall the support. TSB #: 19-AT-008G Page 6 of 12 SUBJECT: ATM SOLENOID DTC P0741, P0743, P0748, P0753, P0758, P075A, P075D, P0763, P0768, P076A, P07B5, P076D, P0773, P0785, P078A, P0995 & P2709 16. Install a new E-module. Install 9 bolts and torque to specification. NOTE: Install the short bolt in the location shown in the circle. Torque: 7~9 lb.ft (1.0~1.2 kgf.m, 10~12 N.m) 17. Confirm that 4 O-rings are seated in the case. 18. Place the valve body on a transmission jack. Rotate the park switch counter-clockwise and carefully raise the valve body and insert the manual valve into the shift lever. Install the valve body fully into the transmission case. NOTICE Confirm the manual valve pin faces outward from the valve body. TSB #: 19-AT-008G Page 7 of 12 SUBJECTATM SOLENOID DTC P0741, P0743, P0748, P0753, P0758, P075A, P075D, P0763, P0768, P076A, P07B5, P076D, P0773, P0785, P078A, P0995 & P2709 19. Install 3 black bolts in the locations shown (black arrow). Install 7 brass bolts in the location shown (red arrows). Torque the bolts to specification. Torque: 7~9 lb.ft (1.0~1.2 kgf.m, 10~12 N.m) 20. Use a 90° pick or similar tool to pull the connector down into position on the valve body. Pull the latch down until it clicks into the tab. 21. Confirm the O-ring is installed at the location shown. Reinstall the valve body cover and torque to specification. Torque: 10~12 lb.ft (1.4~1.6 kgf.m, 14~16 N.m) 22. Reconnect the negative battery terminal. Reset the audio preset stations. TSB #: 19-AT-008G Page 8 of 12 SUBJECT: ATM SOLENOID DTC P0741, P0743, P0748, P0753, P0758, P075A, P075D, P0763, P0768, P076A, P07B5, P076D, P0773, P0785, P078A, P0995 & P2709 23. With the engine off, lift the vehicle on a hoist. Use an 8mm or 5/16” hex socket and remove the fill plug and washer. 24. Remove the overflow plug. Use a fluid pump or suction gun to add SP-IV-RR ATF through the fill plug until ATF flows from the overflow plug. Reinstall the fill plug and overflow plug. . NOTICE Use only SP-IV-RR ATF, P/N 00232-19052. 25. Attach a GDS and select vehicle, Data Analysis, A/T menu and Oil Temperature Sensor. Move the shift lever from P-R-D and back to P. Drive the vehicle until the ATF is at the low end of the range of 122~140°F (50~60°C). TSB #: 19-AT-008G Page 9 of 12 SUBJECTATM SOLENOID DTC P0741, P0743, P0748, P0753, P0758, P075A, P075D, P0763, P0768, P076A, P07B5, P076D, P0773, P0785, P078A, P0995 & P2709 26. Start the engine, shift to Neutral and raise the vehicle on a hoist. Remove the fill plug and overflow plug. Add SP-IV-RR ATF through the fill plug until the ATF flows out the overflow. Reinstall the overflow plug. Torque: 16~18 lb-ft (2.3~2.5 kgf.m, 21~24 N.m) Reinstall the fill plug and washer. Torque: 27~33 lb.ft (3.7~4.6 kgf.m, 33~44 N.m) ATF TEMPERATURE = 122~140°F (50~60°C) SHIFT LEVER IN “P” AND ENGINE RUNNING 27. If the shift cable was moved to add ATF: Install the SST (09480-D2100) or 5mm bolt in the alignment hole of the park position switch. Loosen the adjustment bolt shown. Slide the adjustment bracket rearward to remove the slack in the park cable. Tighten the bolt to specification. Torque: 7~8 lb-ft (0.9~1.0 kgf.m, 9~10 N.m) TSB #: 19-AT-008G SST Bolt Page 10 of 12 SUBJECT: ATM SOLENOID DTC P0741, P0743, P0748, P0753, P0758, P075A, P075D, P0763, P0768, P076A, P07B5, P076D, P0773, P0785, P078A, P0995 & P2709 28. Clear the codes and test drive the vehicle for two driving cycles (two key-on to key-off driving cycles, including 1-2-3-4-5-6-7-8 upshifts and 8-7-6-5-4-3-2-1 downshifts). If the solenoid DTC returns, perform the following repairs: DTC P0741 P074100 P0743 P074300 P0748 P074800 P0753 P075300 P0758 P075800 P075A P075A00 P075D P075D00 P0763 P076300 P0768 P076800 P076A P076A00 P076D P076D00 P0773 P077300 P0785 P078500 P078A P078A00 P2709 P270900 P076A P07B5 P0995 DTC P076A00 P07B500 P099500 SOLENOID DTC REPAIR PROCEDURE Replace the transmission Replace the control wiring harness between the TCM and transmission. If the solenoid DTC does not occur again, return the vehicle to the customer. If the solenoid DTC returns again, replace the TCM. PARK POSITION SWITCH DTC REPAIR PROCEDURE Refer to the G80 or G90 Shop Manual for the related DTC and follow the repair diagnosis for Wiring Inspection and ETM. 29. Clear DTC in the BlueLink system per instructions of TSB 12-BE-005-2. Solenoid Oil Pressure Data Characteristics Input: NOTICE This procedure is necessary only for the following solenoids: P075300, P075800, P076300, P076800, P077300. 30. Select S/W Management, Automatic Transaxle and Oil Pressure Characteristics Input (Solenoid valve Replacement). Select OK and follow the prompts. Select the type of solenoid from the drop-down menu. Select OK. TSB #: 19-AT-008G Page 11 of 12 SUBJECTATM SOLENOID DTC P0741, P0743, P0748, P0753, P0758, P075A, P075D, P0763, P0768, P076A, P07B5, P076D, P0773, P0785, P078A, P0995 & P2709 31. Input the 8-digit code recorded in Step 10 in the blank spaces in the GDS. Select OK. Input the 8 digit code again and select OK. The GDS will confirm the procedure was completed. 32. Drive the vehicle to confirm the proper operation of the transmission. TSB #: 19-AT-008G Page 12 of 12