ITB15033

Classification:
Reference:
Date:
EC15-018
ITB15-033
December 1, 2015
2015 QX80; MIL ON WITH DTC FOR A/F SENSOR
APPLIED VEHICLE: 2015 QX80 (Z62)
APPLIED ENGINE: VK56VD (V8)
IF YOU CONFIRM:
The MIL is ON with one or more of the following DTCs stored:
Bank 1

P2096, P2097 – POST CAT FUEL TRIM SYS B1

P0130, P0131, P0132 – A/F SENSOR1 (B1)

P0031, P0032 – A/F SEN1 HTR (B1)

P014C, P014D, P015A, P015B – Air fuel ratio (A/F) sensor 1 (bank 1)
Bank 2

P2098, P2099 – POST CAT FUEL TRIM SYS B2

P0150, P0151, P0152 – A/F SENSOR1 (B2)

P0051, P0052 – A/F SEN1 HTR (B2)

P014E, P014F, P015C, P015D – Air fuel ratio (A/F) sensor 1 (bank 2)
ACTION:
1. Refer to step 6 in the SERVICE PROCEDURE to confirm ECM reprogramming applies.
2. If reprogramming applies, reprogram the ECM.
3. Replace only the A/F sensors related to the stored DTCs.

If stored DTCs are for only one bank, replace only one A/F sensor for that bank.

If stored DTCs are for both banks, replace both A/F sensors.
NOTE: Do NOT replace both A/F sensors if the stored DTC(s) are for only one bank.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing.
You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to
successfully completing this repair.
Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained
individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that
a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti dealer to determine if this
applies to your vehicle.
1/11
SERVICE PROCEDURE
ECM Reprogramming

Most instructions for reprogramming with CONSULT-III plus (C-III plus) are displayed on the CONSULT
PC screen.

If you are not familiar with the reprogramming procedure, click here. This will link you to the
"CONSULT-III plus (C-III plus) Reprogramming" general procedure.
Preparation for Reprogramming

Take the vehicle for a 10 minute drive in order to meet the
following Idle Air Volume Learn (IAVL) conditions:
 Engine coolant temperature: 70 -105°C (158 - 221°F)
 Battery voltage: More than 12.9V (At idle)
 Transmission: Warmed up
FigureAA
Figure
NOTE:
 After ECM reprogramming is complete, you will be required to perform Throttle Valve
Closed Position, Idle Air Volume Learn (IAVL), and Accelerator Closed Position.
 The above conditions are required for the IAVL to complete.
CAUTION:

Connect the GR8 battery charger to the vehicle battery.
The vehicle battery voltage must stay between 12.0V and 15.5V during reprogramming, or the
ECM/TCM may be damaged.

Be sure to turn OFF all vehicle electrical loads.
If a vehicle electrical load remains ON, the ECM/TCM may be damaged.

Be sure to connect the AC Adapter.
If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted
and the ECM/TCM may be damaged.

Turn off all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range of the
CONSULT PC and the VI. If Bluetooth® signal waves are within range of the CONSULT PC
during reprogramming, reprogramming may be interrupted and the ECM/TCM may be damaged.
2/10
ITB15-033
1. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure.
2. Open C-III plus.
3. Wait for the plus VI to be recognized.

The serial number (Serial No.) will display when the plus VI is recognized.
4. Select Re/programming, Configuration.
Step 3: VI is
recognized
Step
4
Figure 1
5. Follow the on-screen instructions and navigate C-III plus to the screen shown in Figure 2 on the next page.
3/10
ITB15-033
6. When you get to the screen shown in Figure 2, confirm this bulletin applies as follows:
A. Find the ECM Part Number and write it on the repair order.
NOTE: This is the current ECM Part Number (P/N).
6A: Current P/N
Figure 2
B. Compare the P/N you wrote down to the numbers in the CURRENT ECM PART NUMBER column in
Table A below.

If there is a match, this bulletin applies. Continue with the reprogramming procedure.

If there is not a match, ECM reprogramming does not apply. Go to Replace A/F Sensor on page
10.
Table A
CURRENT ECM PART NUMBER: 237105ZA0B, 5ZA1B, 5ZA2B, 5ZA3B
5ZB0B, 5ZB0C
5ZA0D, 5ZA1D, 5ZA2D, 5ZA3D
5ZA0C, 5ZA1C, 5ZA2C, 5ZA3C
4/10
ITB15-033
7. Follow the on-screen instructions to navigate C-III plus and reprogram the ECM.
NOTE:

In some cases, more than one new P/N for reprogramming is available.
 In this case, the screen in Figure 3 displays.
 Select and use the reprogramming option that does not have the message “Caution! Use ONLY
with ITBXX-XXX”.

If you get this screen and it is blank (no reprogramming listed), it means there is no reprogramming
available for this vehicle. Close C-III plus and refer back to ASIST for further diagnosis.
Figure 3
5/10
ITB15-033
8. When the screen in Figure 4 displays, reprogramming is complete.
NOTE: If the screen in Figure 4 does not display (indicating that reprogramming did not complete), refer to
the information on the next page.
9. Disconnect the battery charger from the vehicle.
10. Select Next.
Step
10
Figure 4
NOTE:

In the next steps (page 8), you will perform Throttle Valve Closed Position, Idle Air Volume Learn,
Accelerator Closed Position, and DTC erase.

These operations are required before C-III plus will provide the final reprogramming confirmation
report.
6/10
ITB15-033
ECM recovery:
Do not disconnect plus VI or shut down Consult III plus if reprogramming does not complete.
If reprogramming does not complete and the “!?” icon displays as shown in
Figure 5:

Check battery voltage
(12.0–15.5 V).

Ignition is ON, engine OFF.

External Bluetooth® devices are
OFF.

All electrical loads are OFF.

Select retry and follow the on
screen instructions.

“Retry” may not go through on first
attempt and can be selected more
than once.
Figure 5
If reprogramming does not complete and the “X” icon displays as shown in
Figure 6:

Check battery voltage
(12.0 – 15.5 V).

CONSULT A/C adapter is plugged
in.

Ignition is ON, engine OFF.

Transmission is in Park.

All C-III plus / plus VI cables are
securely connected.

All C-III plus updates are installed.

Select Home, and restart the
reprogram procedure from the
beginning.
Figure 6
7/10
ITB15-033
11. Follow the on-screen instructions to perform the following:

Throttle Valve Closed Position.

Idle Air Volume Learn (IAVL).
NOTE:
 Listed below are the conditions required for IAVL to complete.
 If IAVL does not complete within a few minutes, a condition may be out of range.
o Engine coolant temperature: 70 -105°C (158 - 221°F).
o Battery voltage: More than 12.9V (At idle).
o Selector lever: P or N.
o Electric load switch: OFF (Air conditioner, headlamp, and rear window defogger).
o Steering wheel: Neutral (Straight-ahead position).
o Vehicle speed: Stopped.
o Transmission: Warmed up (ATF TEMP SE less than 0.9V).

Accelerator Pedal Close Position Learning.

Erase DTCs.
Continue to the next page.
8/10
ITB15-033
12. When the entire reprogramming process is complete, the screen in Figure 7 will display.
13. Verify the before and after part numbers are different.
14. Print a copy of this screen (Figure 7) and attach it to the repair order for warranty documentation.
15. Select Confirm.
Step
13
Step
14
Step
15
Figure 7
16. Close C-III plus.
17. Turn the ignition OFF.
18. Disconnect the plus VI from the vehicle.
Go to the next page.
9/10
ITB15-033
Replace A/F Sensor
1. Replace only the A/F sensor related to the stored DTCs.

If stored DTCs are for only one bank, replace only one A/F sensor for that bank.

If stored DTCs are for both banks, replace both A/F sensors.

Refer to the Electronic Service Manual (ESM), section EM-Engine Mechanical, for replacement
information.
NOTE: Do NOT replace both A/F sensors if the stored DTC(s) are for only one bank.
2. Test drive the vehicle and make sure it operates correctly and the MIL is OFF.

If the MIL comes ON, go back to ASIST for further diagnostic information.

Diagnosis and repairs beyond the contents of this bulletin are not covered by this bulletin.
10/10
ITB15-033
PARTS INFORMATION
DESCRIPTION
PART NUMBER
A/F Sensor
22693-1PM0A
(Bank 1 and Bank 2)
NOTE: Both banks use the same A/F sensor Part Number.
QTY
1 or 2
as needed
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
Replace A/F Sensor
One
DESCRIPTION
PFP
OP CODE
SYM
DIA
RPL ONE AIR/FUEL RATIO
(1)
DE53AA
HD
32
SENSOR
(1) Use the A/F sensor part number listed above in the parts information table as the PFP.
(2) Reference the current Infiniti Warranty Flat Rate Manual and use the indicated FRT.
FRT
(2)
Or
Both
DESCRIPTION
PFP
OP CODE
SYM
DIA
RPL BOTH AIR/FUEL RATIO
(1)
DE55AA
HD
32
SENSORS
(1) Use the A/F sensor part number listed above in the parts information table as the PFP.
(2) Reference the current Infiniti Warranty Flat Rate Manual and use the indicated FRT.
FRT
(2)
And on the same repair line:
DESCRIPTION
OP CODE
FRT
Reprogram ECM
DE97AA
(2)
(2) Reference the current Infiniti Warranty Flat Rate Manual and use the indicated FRT.
NOTE: FRT allows adequate time to access DTC codes. No other diagnostic procedures subsequently
required. Do NOT claim any diagnostic OP Codes with this claim.
11/10
ITB15-033