Altec Aerial Device 2021

Vehicle Details: Recalls, Service Bulletins

Below you will find all available information on the 2021 ALTEC Aerial Device.

ManufacturerKnown WMI(s)Fuel Type
ALTEC
ALTEC VIN Decoder

Use the box here to look up VINs from ALTEC as well as other manufacturers

#

Sub-models: - Aerial Device Jems Hybrid -

Frequently Asked Questions
  • Are there recalls for the 2021 ALTEC Aerial Device?
     - There are 21 recall(s) for the 2021 ALTEC Aerial Device, additional information is below.
NHTSA Mandated Recalls

  • Recall 253019 [USA]: A short circuit increases the risk of a fire.

  • Recall 238900 [USA]: Loose fasteners can allow the welder to detach from the vehicle, becoming a road hazard and increasing the risk of a crash.

  • Recall 237434 [USA]: An outlet without gfci protection may fail to shut off electrical power when a ground-fault occurs, increasing the risk of injury or fire.

  • Recall 237113 [USA]: An active braking system that fails to activate as intended increases the risk of a crash.

  • Recall 240331 [USA]: An electrical short-circuit can increase the risk of a fire.

  • Recall 234430 [USA]: A missing weld on the rear pole rack can lead to a crack that could cause the pole and rack to drop in height, increasing the risk of an injury.

  • Recall 234745 [USA]: Outriggers that are not set when loads are being lifted by the jib winch may cause the unit to tip, increasing the risk of injury.

  • Recall 203892 [USA]: A cracked weld may allow the auger bracket to detach from the boom, increasing the risk of injury.

  • Recall 203950 [USA]: A blown fuse can cause an engine stall, increasing the risk of a crash.

  • Recall 183454 [USA]: Unsecured fuel lines may become damaged and leak fuel, increasing the risk of a fire.

  • Recall 230443 [USA]: Elevated levels of carbon monoxide gas may not be detected, increasing the risk of injury.

  • Recall 183456 [USA]: Unsecured fuel lines may become damaged and leak fuel, increasing the risk of a fire.

  • Recall 231236 [USA]: Shear plate failure can result in the separation of the subbase and truck frame, increasing the risk of injury.

  • Recall 208725 [USA]: Broken bolts can cause separation of the pedestal and turntable, increasing the risk of injury.

  • Recall 200936 [USA]: Broken bolts can cause the pedestal to separate from the turntable, increasing the risk of injury.

  • Recall 188771 [USA]: The boom moving in an unintended direction increases the risk of injury.

  • Recall 209651 [USA]: The operator could overextend the boom while using the material handling jib, causing the aerial device to tip over and increasing the risk of injury.

  • Recall 204943 [USA]: Broken bolts can cause the pedestal to separate from the turntable, increasing the risk of injury.

  • Recall 204272 [USA]: Uncontrollable boom movement increases the risk of injury.

  • Recall 209017 [USA]: Overloaded bolts can fail, causing the pedestal to separate and increasing the risk of injury or death.

  • Recall 188405 [USA]: Unintended movement of the lower and upper booms increases the risk of injury.

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Recalls are also available on the Complaints page
Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • SIL 3123 - EQUIPMENT: Altec has learned that section 9 of the maintenance and parts manual for certain ac45e cranes built from september 2020 to november 2023 contains an incorrect torque value of 250 foot-pounds (339 na??M) for the rotation gearbox mounting cap
  • SIL 3065 - EQUIPMENT: Altec has learned that the pressure plates in the reel motor were not manufactured to specification, causing the plates to stick together. This can cause the reel park brake to not fully release, or cause the reel motor to lock up on certai
  • SIL 3099 - SUSPENSION: Altec has learned that on certain altec units equipped with air suspension built from april 2020 to june 2023, some operators may be dumping the chassis airbags before deploying the outriggers. This can cause the airbags to become damaged.
  • SIL 3110 - EQUIPMENT: Altec learned that a connection in the upper controls joystick in certain oem controls on at238p aerial devices built from november 2020 to august 2022 can fail due to wire movement during use and issued sil-845 to re-manufacture controller
  • CSR 3109 - ENGINE AND ENGINE COOLING: Altec industries, inc. Has received notification from ford motor company that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. Certain 2020 to 2022
  • CSR 3104 - SEATS: Altec industries, inc. Has received notification from ford motor company that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. On certain expeditio
  • SIL 3060 - ELECTRICAL SYSTEM: Altec has learned that on certain at37me/pe/se, at41me/pe/se, and at48me/pe/se units built from august 2021 to june 2022 due to a missing valve driver calibration, the estimated output current for certain functions may exceed the digital fu
  • SIL 3054 - ELECTRICAL SYSTEM: Altec has learned that certain units built with a jobsite energy management system (jems) s/se/le from october 2020 to may 17, 2023, may fail to charge or operate properly, particularly when the battery is cold. Altec has developed a firmwa
  • CSR 3093 - ELECTRICAL SYSTEM: Altec industries, inc. Has received notification from navistar, inc. That a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. Navistar has decided tha
  • SIL 3082 - EQUIPMENT: Altec has learned that section 8 of the maintenance manual for certain altec ls60 aerial devices built from november 2017 to january 2023 contains an incorrect torque value of 325 foot-pounds for the rotation gearbox mounting cap screws. Al
  • SIL 3068 - EQUIPMENT: Altec has learned that certain digger derricks and aerial devices of various models built from january 2010 to january 2023 may contain access steps with a handrail and side plate that come together in a small space causing a potential pinc
  • CSR-3092 - VISIBILITY: Altec industries, inc. Has received notification from daimler truck north america llc (dtna), on behalf of its freightliner truck division, that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you
  • CSR 3088 - SERVICE BRAKES, HYDRAULIC: Altec industries, inc. Has received notification from general motors (gm) that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. These vehicles may
  • CSR 3075 - PARKING BRAKE: Altec industries, inc. Has received notification from navistar, inc. That a condition exists relating to motor vehicle safety, compliance, or emissions in certain 2022 through 2024 model year navistar hv and mv series vehicles built from ja
  • CSR 3071 - ENGINE AND ENGINE COOLING: Altec industries, inc. Has received notification from fiat chrysler automobiles (fca us) that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. Cert
  • CSR 3070 - ENGINE AND ENGINE COOLING: Altec industries, inc. Has received notification from fiat chrysler automobiles (fca us) that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. Cert
  • SIL 3021 - EQUIPMENT: The rear out and down outriggers on certain ls60 aerial devices built from july 2018 to april 2022 might contain a dual bonded hose with an externally attached electrical cable in the horizontal leg to operate the hydraulic cylinder and pro
  • CSR3063 - ELECTRICAL SYSTEM: Altec industries, inc. Has received notification from warn industries, inc. That a bumper winch supplied on certain altec units could contain a defect related to motor vehicle safety. Certain altec units built from december 2020 to septembe
  • SIL 3041 - EQUIPMENT: Altec has learned that when the coolant-style oil heater on certain ah75b/85B100B aerial devices built from april 2021 to august 2022 is active, the operator has to turn off the engine in order to disengage the power take-off (pto). Replace
  • CSR 3050 - STEERING: Altec industries, inc. Has received notification from navistar that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. Navistar has decided that cert
  • 074900856 - ELECTRICAL SYSTEM: Altec used telematics data to identify jems in the field with batteries approaching critical discharge. After the min cell voltage becomes less than 3000mv the battery is no longer rechargeable in the field. To avoid costly battery replacem
  • SIL 3036 - EQUIPMENT: Altec has learned that the outrigger instructional placards were not installed during the initial production of certain lr8rm aerial devices built from february 2021 to november 2021. Altec has created a placard installation kit containing
  • SIL 3037 - EQUIPMENT: Altec has learned that the stability test form in the maintenance manuals for ls49 aerial devices built from july 2019 to july 2022 contains incorrect test weight information. This information has been corrected in the currently published m
  • CSR 3042 - ENGINE AND ENGINE COOLING: Altec industries, inc. Has received notification from fiat chrysler automobiles (fca) that a condition exists relating to motor vehicle safety, compliance, or emissions in vehicles that are equipped with altec equipment. Certain 2021 and 20
  • SIL 3035 - FUEL SYSTEM, GASOLINE: Owners of certain at series and ta40/45 series aerial devices built on dodge ram 4500/5500 chassis from 2016 to 2022 received altec product notice csn 855 in may of 2022 calling for the inspection of fuel line securement. We have identified
  • SIL 3027 - EQUIPMENT: Altec has learned that certain at48mw and at48pw units built from july 2021 to april 2022 were manufactured with the proper system pressure setting, but the serial number placard and the maintenance manual state a different system pressure
  • SIL 3020 - EQUIPMENT: Altec has learned that the threaded hardware between the rotary joint and slip ring could have been installed incorrectly on certain aa, an, an-oc, am, and a class aerial devices built from january 2021 to february 2022. This can cause the
  • SIL-859 - EQUIPMENT: Altec has learned that on ah75/85/100, ah75a/85a/100a, and hl125 aerial devices built from november 2003 to january 2021, there is potential for the jib rotational positioning pin to disengage when the platform is tilted down 90 degrees or
  • CSR-3032 - EQUIPMENT: Altec industries, inc. Has received notification from general motors (gm) that for certain 2019 to 2022 chevrolet silverado 4500hd, 5500hd, and 6500hd vehicles the power take-off (pto) will kick out and/or disengages intermittently. This co
  • SIL-3011 - ELECTRICAL SYSTEM: Altec has determined there is a missing diode that allows feedback from the auxiliary air compressor to the ignition in certain vehicles equipped with cb5 cranes built from august 2021 to june 2022. This feedback prevents the engine on the
  • PA713 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL: Product advisory posted on our web site to inform owners, user, & operators that the new ansi a92.2-2021 standard has taken effect and they must review. The standard has changed some of the responsibilities of the parties who use or operat
  • SIL-857 - STRUCTURE: Certain 2020 through 2021 model year f-550 vehicles equipped with a payload plus upgrade package and a 19,500 lbs. Gvwr were ordered from ford with a frame rail specification that does not meet the original equipment manufacturer (oem) spec
  • CSR-541 - UNKNOWN OR OTHER: Altec industries, inc. Has received notification from ford motor company that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. The windshield wiper
  • SIL 856 - EQUIPMENT: Altec has learned of the potential for washers on the outer race rotation bearing cap screws to overlap the adjacent weld on at238p and at335 aerial devices built from october 2019 to november 2021. While there have been no reports of unit
  • SIL 850 - ELECTRICAL SYSTEM: The body compartment wiring on certain altec aerial devices, digger derricks, and body-only units built from 2014 to 2021 contains an in-line fuse located close to the lighting in the compartment, while other units are fused upstream, close
  • SIL 852 - EQUIPMENT: Altec has learned that the electrohydraulic outrigger/tools control valve on aa755l and a-series aerial devices and dlb, dmb, and d2/3/4000b series digger derricks could have the potential to produce a very small amount of flow into the low
  • SIL 845 - UNKNOWN OR OTHER: Altec has learned that a connection in the upper controls joystick on at238p aerial devices built from november 2020 to september 2021 can fail due to wire movement during use. If this happens with the boom elevated, the operator in the pla
  • SIL 848 - EQUIPMENT: Altec has learned that the engine on certain at35/37/40g and at37/41/48 me/pe aerial devices built from august 2020 to august 2021 on ford f-450/f550/f-600 gas engine chassis equipped with a jems s/se hybrid system could not enter idle miti
  • CSR 539 - FUEL SYSTEM, DIESEL: Altec industries, inc. Has received notification from an original equipment manufacturer (oem) that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment
  • CSR 537 - STEERING: Altec industries, inc. Has received notification from ford motor company that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. Ford motor company
  • CSR 536 - EQUIPMENT: Altec industries, inc. Has received notification from fiat chrysler automobiles (fca) that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. Fca us
  • CSR 532 - POWER TRAIN: Altec industries, inc. Has received notification from navistar that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. On certain trucks equipped
  • CSR 530 - EQUIPMENT: Altec is committed to providing our customers reliable products from initial delivery throughout the useful life of the machine. Ford motor company has decided that a defect that relates to motor vehicle safety exists in certain 2021 mod
  • CSR 529 - EQUIPMENT: Altec industries, inc. Has received notification from an original equipment manufacturer (oem) that a condition exists. This condition relates to the operation or customer satisfaction of the unit when equipped with an altec aerial device o
  • No comms 2021-12 - UNKNOWN OR OTHER: There are no manufacturer communications in accordance with 49 cfr 579.5 to report for december 2021 for altec industries, inc.
  • CSR 527 - FIRERELATED:IGNITION/KEY ON:ENGINE OFF: Fiat chrysler automobiles us has decided that a defect that relates to motor vehicle safety exists on certain 2021 through 2022 model year (dj) ram 2500 pickup, (d2) ram 3500 pickup, (dd) ram 3500 cab chassis, and (dp) ram 4500/5500 cab cha
  • SIL 839 - UNKNOWN OR OTHER: Some customers have reported the loss of functionality of the altec unit or the ez trac system on certain 2016-2021 ford f750 chassis with ez trac hydraulic all-wheel drive installed. The investigation has shown that improper wiring could h
  • PUN 2021D - EQUIPMENT:OTHER:LABELS: Altec has learned that the labeling describing the proper jump starting procedure for certain vehicles equipped with a jobsite energy management system (jems) 2, 4, 6, or 12 built by altec from 2015 to 2021 has sometimes been overlooked. Fa
  • SIL 831 - EQUIPMENT: Altec has discovered that certain at200a aerial devices built from june 2020 to january 2021 could have square inside corners on a mounting frame side plate. The square corners can cause excessive stress levels in the side plate. Over time
  • SIL 810 - EQUIPMENT: Chafing can occur on hoses at the rear of the turntable on certain ls60 aerial devices built from february 2018 to february 2021. Altec requires the hose routing to be inspected on the affected units no later than the next periodic maintena
  • PUN 2021B - ELECTRICAL SYSTEM: The system firmware on the altec jobsite energy management system (jems) s/se/le built from 2020 to 2021 is being updated to improve the performance of the telematics system. This update does not affect the operation of the jems system. Thi
  • SIL 806 - EQUIPMENT: Altec has learned that certain rear-mounted lr7 units built from may 2019 to april 2021 have reports of the platform ribs separating from the platform shell near the bottom of the platform. The separation can be caused by excessive bouncing
  • SIL 805 - EQUIPMENT ADAPTIVE/MOBILITY: Altec has learned that certain ts20-4p units built from 2019 to 2021 have fairlead rollers that do not consistently rotate freely. This operation can cause damage to the ropes. Altec requires that the levelwind fairleads be replaced within
  • CRS 512 - POWER TRAIN: Cummins has launched a customer satisfaction campaign for certain cummins b6.7 diesel engines produced between august 26, 2020 and october 5, 2020, that may have been installed. Some of the affected vehicles may contain engine valve spring

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.