Ford Fusion 2012

• Recall 229928 [USA]: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
  Ford motor company (ford) is recalling certain 2007-2011 ranger, 2006-2012 fusion, lincoln zephyr, lincoln mkz, 2006-2011 mercury milan, 2007-2010 ford edge, and lincoln mkx vehicles. The driver's side air bag inflator may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
  ford will notify owners, and dealers will replace the driver-side airbag inflator or module with an alternate one, free of charge. Owner notification letters were mailed on april 9, 2021 for the passenger side, and november 14, 2022 for the driver side. Owners may contact ford customer service at 1-866-436-7332. Ford's number for this recall is 21s12.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 198532 [USA]: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
  Ford motor company (ford) is recalling certain 2005-2014 mustang, 2004-2011 ranger, 2009-2011 mercury milan, 2006 ford gt, 2008-2012 fusion, 2007-2010 edge and lincoln mkx, and 2009-2010 lincoln mkz vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
  ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began march 17, 2021. Owners may contact ford customer service at 1-866-436-7332. Ford's number for this recall is 21s05.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 126890 [USA]: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
  Ford motor company (ford) is recalling certain 2014 ford mustang vehicles sold, or ever registered, in the states of alabama, california, florida, georgia, hawaii, louisiana, mississippi, south carolina, texas, puerto rico, american samoa, guam, the northern mariana islands (saipan), and the u.S. Virgin islands or "zone a." additionally, ford is recalling certain 2011 ford ranger and mercury milan vehicles, 2011-2012 ford fusion and lincoln zephyr/mkz vehicles and 2011-2014 ford mustang vehicles sold, or ever registered, in the states of arizona, arkansas, delaware, district of columbia, illinois, indiana, kansas, kentucky, maryland, missouri, nebraska, nevada, new jersey, new mexico, north carolina, ohio, oklahoma, pennsylvania, tennessee, virginia, and west virginia or "zone b." ford is also recalling certain 2010 ford edge and lincoln mkx vehicles, 2010-2011 ford ranger and mercury milan vehicles, 2010-2012 ford fusion and lincoln zephyr/mkz vehicles, and 2010-2014 ford mustang vehicles sold, or ever registered, in the states of ak, co, ct, id, ia, me, ma, mi, mn, mt, nh, ny, nd, or, ri, sd, ut, vt, wa, wi, and wy or "zone c." these vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
  ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began february 13, 2019. Owners may contact ford customer service at 1-866-436-7332. Ford's number for this recall 19s01.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 120708 [USA]: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
  Ford motor company (ford) is recalling certain 2012 ford fusion and mustang and lincoln zephyr and mkz vehicles originally sold, or ever registered, in alabama, california, florida, georgia, hawaii, louisiana, mississippi, south carolina, texas, puerto rico, american samoa, guam, the northern mariana islands (saipan), and the u.S. Virgin islands, or "zone a." additionally, unless included in "zone a" above, ford is recalling certain 2009 ford ranger, edge, fusion and mustang, lincoln mkx, mkz and zephyr and mercury milan vehicles originally sold, or ever registered, in arizona, arkansas, delaware, district of columbia, illinois, indiana, kansas, kentucky, maryland, missouri, nebraska, nevada, new jersey, new mexico, north carolina, ohio, oklahoma, pennsylvania, tennessee, virginia and west virginia, or "zone b." additionally, unless included in "zone a" or "zone b" above, ford is recalling certain 2007-2008 ford ranger, edge and lincoln mkx, 2006-2008 ford fusion, mercury milan, lincoln zephyr and mkz, 2005-2008 ford mustang and 2005-2006 ford gt vehicles originally sold, or ever registered, in the states of alaska, colorado, connecticut, idaho, iowa, maine, massachusetts, michigan, minnesota, montana, new hampshire, new york, north dakota, oregon, rhode island, south dakota, utah, vermont, washington, wisconsin and wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
  ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Interim letters informing owners of the recall and that parts are not yet available began mailing march 1, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact ford customer service at 1-866-436-7332. Ford's number for this recall is 19s01.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 115502 [USA]: If the vehicle experiences a loss of power steering assist, extra steering effort will be required at lower speeds, increasing the risk of a vehicle crash.
  Ford motor company (ford) is recalling certain model year 2011-2012 ford fusion vehicles without a 3.5l engine and lincoln mkz hybrid electric vehicles, 2011 mercury milan vehicles, 2011-2012 ford taurus, ford flex, lincoln mks, and lincoln mkt vehicles equipped with a 3.5l gtdi engine and 2013 ford taurus, ford flex, lincoln mks, and lincoln mkt vehicles equipped with any available engine. The affected vehicles have electric power steering assist systems that may shut down as a result of a steering motor sensor fault.
  ford will notify owners, and dealers will check the power steering control module (pscm) for diagnostic trouble codes (dtc). If dealers find any loss of steering assist dtcs, the steering gear will be replaced, free of charge. If, no codes are found during the pscm inspection, the pscm software will be updated, free of charge. The recall began on july 21, 2015. Owners may contact ford customer service at 1-866-436-7332. Ford's number for this recall is 15s18.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall R/2019/156 [UK]: Takata air bag inflator may rupture on deployment
  Air bag inflators may not operate as intended
  replace air bag inflator

  Show Content

• Recall 2021077 [Canada]: Airbag
  Issue: this recall is for certain vehicles that had the driver-front and/or passenger-front airbag inflator replaced after a collision or theft. An obsolete airbag may have been installed. On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the driver-front airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Safety risk: if the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective action: the company will notify owners by mail and instruct you to take your vehicle to a ford dealer to inspect the driver and/or passenger airbag inflator or module and replace it, if necessary. Note: the canadian climate results in the propellant degrading slowly. This recall is being conducted as a precaution to address future risk. It is expected that all airbag inflators will be replaced before their function would be affected.

  Show Content

• Recall 2021029 [Canada]: Airbag
  Issue: on certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the driver-front airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Safety risk: if the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective action: ford will notify owners by mail. The corrective actions for this recall are under development. Note: the canadian climate results in the propellant degrading slowly. This recall is being conducted as a precaution to address future risk. It is expected that all airbag inflators will be replaced before their function would be affected.

  Show Content

• Recall 2019005 [Canada]: Airbag
  Issue: on certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the passenger-front airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Safety risk: if the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective actions: owners will be notified by mail and instructed to take their vehicle to a dealer to have the passenger-front airbag inflator replaced. Note: the canadian climate results in the propellant degrading slowly. This recall is being conducted as a precaution to address future risk. It is expected that all airbag inflators will be replaced before their function would be affected. Additional note: this recall supersedes recalls 2016-347 (ford safety improvement program 16s26), 2017-024 (ford recall 17s01) and 2018-035 (ford recall 18s01). Vehicles repaired under the previous recalls do not require repair under this recall.

  Show Content

• Recall 2015224 [Canada]: Steering
  On certain vehicles, a fault in the electric power steering (eps) system could result in an immediate loss of power steering assist without warning to the driver. This would unexpectedly increase the steering effort force necessary to steer the vehicle at lower vehicle speeds, which could increase the risk of a crash causing injury and/or damage to property. Correction: dealers will affect repairs as necessary and will reprogram the eps controller with updated software. In the event that an eps fault occurs, this updated software would allow for continued eps function while displaying visual and audible warnings to the driver until the end of the drive cycle.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

The following is a list of any known keyfobs for the Ford Fusion 2012 as well as their FCC IDs if available

• RHK-FRD042: 2011-2012 Ford Edge Fusion F-Series / 3-Button Remote Head Key / PN: 164-R7043 / OUCD6000022 / H75 / Chip 80 Bit (OEM Refurb)
  FCC ID: OUCD6000022

• Pedestrian alert sounds investigation # DP22005

  Nhtsa received a petition on or about july 18, 2022, requesting that federal motor vehicle safety standard (fmvss) 141 be applied to all electric and hybrid vehicles operating in the united states. The petition can be reviewed at nhtsa.Gov under odi number 11486072. Fmvss 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 kg or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after march 1, 2021.On january 27, 2023, nhtsa opened defect petition (dp) 22-005 to evaluate the subject matter described in the petition. On june 24, 2023 and as supplemented on june 25, 2023, the petitioner notified nhtsa he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioners withdrawal, dp22-005 is closed. Closure of this dp does not represent a determination by nhtsa regarding the subject matter of the petition.
  

  Show Content

• Desiccated air bag inflator rupture investigation # EA21002

  There is no summary currently available
  

  Show Content

• Power steering failure investigation # EA17004

  On september 28, 2016, the office of defects investigation (odi) opened a preliminary evaluation (pe16-011) to investigate claims of power steering assist loss on model year (my) 2010 ford fusion vehicles.  during the pe, odi received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning.  ford motor company (ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem.  it should be noted that as the result of investigation pe14-030, ford conducted a safety recall (15v-340) ofmy 2011-2012 ford fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On november 20, 2017, pe16-011 was upgraded to this engineering analysis (ea17-004) to further assess the scope, frequency, and consequence of this failure.  this was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age.  at the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned pe14-030. During the ea, odi’s analysis of the alleged defect in the subject vehicles identified the following:  testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a dtc is set, a lower failure rate than the recalled fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified.  accordingly, this engineering analysis is closed.  see the attached engineering analysis closing report for details.  the closing of this investigation does not constitute a finding by nhtsa that a safety defect does not exist, and odi will take further actions if warranted by future circumstances.  to review the reports cited in the closing resume odi report identification number document, go to nhtsa.Gov.
  

  Show Content

• Electric power steering failure investigation # PE14030

  The office of defects investigation (odi) opened a preliminary evaluation to investigate complaints of the loss of power steering while driving. The subject vehicles are equipped with a rack mounted electric power assisted steering (epas) unit.Some of the complaints alleged that the steering assist failed and resulted in increased steering efforts that contributed to a loss of control and in some cases a crash.The epas system was manufactured by trw automotive for ford and was designated as generation i.These units were first produced and put into vehicle production in july 2008 beginning with the model year (my) 2010 ford fusion and mercury milan.The system is comprised of a mechanical steering rack-and-pinion gear with torque sensor, electric assist motor, motor position sensor and a power steering control module (pscm). The pscm is self-monitoring and designed to detect faults within the system and can store diagnostic trouble codes (dtcs) if a problem is detected.There are 29 potential dtcs the system can detect.Many of these allow the system to go into reduced-assist steering mode by using the default vehicle speed signal should the live speed signal be lost, if voltage to epas system falls below 10.7 or goes above 17 volts, the temperature at the pscm goes above 105c (221f), or if high friction is detected.Some dtcs will cause the system to go into manual steering mode (no assist). On july 1, 2015, ford filed a defect information report (dir) identifying a safety related defect in trw gen i epas systems installed in some of the subject vehicles (nhtsa recall 15v-340, ford no. 15s18).The dir indicated that intermittent electrical connections caused by quality issues associated with conformal coat contamination and ribbon cable pin misalignment within the steering gear motor may lead to a loss of the motor position sensor signal, resulting in a sudden loss of power assist while driving.The recall covers approximately 393,623 vehicles built from september 2010 through february 2012:2011-12 fusion built sep 2010 - feb 2012; 2011-12 lincoln mkz built sep 2010 - feb 2012; 2011 milan built sep 2010 - dec 2010; 2011-13 taurus built sep 2010 - feb 2012; 2011-13 flex with 3.5l gtdi engine built sep 2010 - feb 2012; and 2011-13 mks, mkt with 3.5l gtdi engine built sep 2010 - feb 2012.The repair consists of updating the pscm software to prevent a loss of steering assist while driving. The revised software will provide audible and visual warnings to the driver. If one or more of the following dtcs are stored, C1B00-62, C200B-2f, C200B-61, C200B-62, C200C-2f, C200D-49, U0300-00, U2011-49, U2011-61, U3000-46, U3000-49, U3000-61, U3000-72, U3000-96, P07AE-09, the dealer will replace the epas system at no charge to the owner.Odis analysis of failure data for this pe identified a total of 2,584 complaints to odi and ford and 9,967 ford warranty claims related to the alleged defect.The recalled vehicles account for 1,634 of the complaints and 7,311 of the warranty claims.Odis analysis identified 40 complaints alleging crashes that may be related to loss of steering assist while driving, 20 of which involved vehicles included in fords recall.The information available for the alleged crashes were not sufficient to assess specific causes of the incidents or to verify epas malfunctions in each case.Most of the crashes were low-speed impacts with curbs or roadside objects resulting in wheel or minor body damage.None of the injury claims indicated medical attention was required.In addition, statistical modeling of the failure data by nhtsas national center for statistics and analysis projected 10-year failure rates of approximately 8-14 percent for the recalled vehicles and approximately 1 percent for the non-recalled subject vehicles.This investigation is closed.All odi complaints associated with this closing resume are listed in the attachment.
  

  Show Content

• Electronic throttle body malfunction investigation # PE13003

  On february 21, 2013, the office of defects investigations (odi) opened preliminary evaluation pe13-003 to investigate allegations of electronic throttle body (etb) failures resulting in sudden reduction of engine power in model year (my) 2009-2013 ford escape, fusion, mariner and milan vehicles. During this investigation, ford identified a condition in subject vehicles equipped with 2.5l and 3.0l engines that may result in a sudden reduction of engine power.According to ford, the etb internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the malfunction indicator lamp (mil) or wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?S trade name for the feature is failure mode effects management (fmem) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.Odi?S complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 rpm. Analysis of warranty claims provided by ford identified 59,807 claims related to etb replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (dtc) P2111, throttle body stuck open, and P2112, throttle body stuck closed.Ford described several factors where the etb motor may fail resulting in dtcs P2111 or P2112 but the failure is not an existing stuck open or closed etb valve position.According to ford, the etb control strategy provides the driver with three fmem modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.Dtcs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other fmem limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, ford and its suppliers, delphi and igarashi, updated the powertrain control module (pcm) software to include a throttle body motor cleaning cycle during key-on and modified the etb internal motor components design, surface finish and material composition to improve durability. Additionally, ford developed a remedy procedure and issued a special customer satisfaction program (csp) 13n03 extending the etb warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through january 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a ford dealer who will reprogram the pcm to the latest calibration. The bulletin was sent to dealers on january 17, 2014 and the owner letter mailing began on january 27, 2014. See the investigative file for copies of fords bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
  

  Show Content

A few weeks ago i went to slow to a stop at the end of my driveway at approximately 5mph. My brake pedal dropped to the floor and i had to repress on the brake pedal to come to a complete stop. It continued working properly for a week or so when it happened again. The same week i was backing out of another driveway slightly down hill and attempted to come to a complete stop to look for traffic. Luckily there was none because my stopping distance was around 12 ft or so going maybe 3mph with the brakes completely pressed. I have since had my brake pads changed and all other components checked and was told were working properly. Now my stopping distance at 10mph is at least 3-4ft. I am too afraid to drive my vehicle at higher speeds on any road due to the stopping distance issues.

A recall was issued in 2015..15s18.. It seems my vin number isn't included in the recall because it was manufactured in new mexico. My power steering at 70 mph goes out without any warning. The above recall is exactly what's happening with my vehicle. Now i am obligated to pay 2k to fix a manufacturing flaw. This is a huge saftey issue to be on the road and while your driving your power steering goes out. I am asking for further investigation as my car is a 2012 ford fusion with the same problem you issued a recall for. I can be reached at [xxx]. [xxx] parts of this document have been redacted to protect personally identifiable information pursuant to the freedom of information act (foia), 5 u.S.C. 552(b)(6).

Over the past few days driver side door would not open from the inside of the vehicle. Rolling down the window and opening the door from the outside is the only option in opening the driver side car door. This is a safety concern as if i were ever in need to exit the vehicle in an emergency manner i can not easily or quickly get out of the car we’re under water, on fire, etc. My vehicle is not the only vehicle that is having this issue, i have heard reports from mechanics, other ford fusion drivers, and personal experience that ford fusions from about 2006-2013 are having this issue. The issue needs to be addressed for safety concerns and is only happening on the drivers side door.

The contact owns a 2012 ford fusion. The contact stated while driving at various speeds, the vehicle lost power steering assist and the vehicle became difficult to steer. The contact stated that the traction control warning light was illuminated. The vehicle was taken to an independent mechanic where it was diagnosed with the power steering needing to be replaced. The vehicle was not repaired. The contact was relating the failure to nhtsa campaign number: 15v340000 (steering). The manufacturer was informed of the failure and referred the contact to the nhtsa. The failure mileage was approximately 118,000.

1) brake hydraulic control unit (hcu) failure. Dealership removed and replaced hcu assembly and abs module. All parts retained by dealer. 2) hcu brake failure made stopping very difficult and slow to stop. Dealer recommended not driving until repaired. 3) dealer confirmed hcu failure with computer code analysis. 4) hcu and effected parts not inspected by anyone other than dealer. 4) numerous red abs and brake warning lights upon backing out of garage to street. I shut the engine off and restart in the hope of correction, to no avail. Problem re-occurred. Vehicle could be stopped but with difficulty -- slow to stop and hard to stop. Dealer replaced hcu assembly and abs module and added pm1c brake fluid (dot3), this hcu failure apparently has been a problem in ford fusion and other ford vehicles (see safety recall 19s54 -anti-lock brake system hydraulic control unit valve function -- 2006-2010 ford & lincoln mercury). It doesn't look like the problem has been resolved. Note that brake fluid used is dot 3 and not the ntsb recommended remedy dot 4 brake fluid

The contact owns a 2012 ford fusion. The contact stated while entering and starting the vehicle, a message appeared on the screen which stated that the power steering assist was disabled. The contact attempted to reverse out of the drive way however, the steering wheel failed to turn. The contact shifted the vehicle backed into park. The local dealer was contacted about the failure however, the dealer was unable to inspect the vehicle. The vehicle was not diagnosed nor repaired. The manufacturer was made aware of the failure. The failure mileage was 156,000.

The contact owns a 2012 ford fusion. The contact stated that while reversing, the electric power steering failed and the steering wheel ceased. The failure occurred on three separate occasions. The dealer was not made aware of the failure. The vehicle was not diagnosed nor repaired. The manufacturer was made aware of the failure and the contact was informed that the vin was not under recall. The failure mileage was approximately 52,000.

Unknown one day i was driving my car like normal, i stopped and parked it and a message saying "service power steering now" popped up. I immediately lost all power steering.

Power steering service now light came on driving away from my neighborhood and started making a loud noise on right front wheel of car, pulled over to see if i had a flat and did not. Turned around and went back home so i wouldn’t get stuck somewhere or wreck. While driving to the shop to get it looked at the power steering failed and could barely turn the wheel. This could have resulted in a wreck. The shop confirmed the power steering is out on the car again! Power steering sensor was recently replaced after wreck therefore it shouldn’t be going out a month later.

Common OBD-II Error Codes

• P0030 [1] HO2S Heater Control Circuit (Bank 1 Sensor 1)
• P0130 [1] 02 Sensor Circuit Malfunction (Bank I Sensor 1)
• P0A7E [1] Hybrid Battery Pack Over Temperature
• P2111 [2] Throttle Actuator Control System - Stuck Open
• P2112 [2] Throttle Actuator Control System - Stuck Closed
• U0554 [1] Invalid Data Received From Accessory Protocol Interface Module
• P07AE [1] Transmission Friction Element "G" Performance/Stuck Off
• U0300 [1] Internal Control Module Software Incompatibility
• U2011 [1] Module Transmitted Invalid Data (Non SCP)
• U3000 [1] Control Module
• C1B00 [1] C1B00
• C200B [1] C200B
• C200C [1] C200C
• C200D [1] C200D