MACK CHMack Ch

Vehicle Details: Consumer Complaints, Service Bulletins

Below you will find all available information on the MACK CH, manufacturered by Mack Trucks Inc..

ManufacturerKnown WMI(s)Fuel Type
MACK1M1 1M2 1M3 2M1 2M2 2M3 VG6 VG8
MACK VIN Decoder

Use the box here to look up VINs from MACK as well as other manufacturers

#
Frequently Asked Questions
  • Where is the MACK CH produced?
     - The MACK CH is produced in Greensboro North Carolina, United States (usa).
NHTSA Mandated Recalls

No recalls could be found for this vehicle. To ensure accuracy and for your safety, do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • KC-880 - VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:CONDENSOR/EVAPORATOR: Evaporator may not drain properly and may lead to blower motor failure
  • KC-940 - POWER TRAIN: Mack drive axle shaft flange to hub rtv gasket repair
  • KC-733 - ENGINE AND ENGINE COOLING: Back office mack chassis - secondary gauge set up - model year 2018 and newer.
  • KC-2107 - ENGINE AND ENGINE COOLING: Def level (uqls) sensor troubleshooting guide - us17+obd16 emissions and newer.
  • KC-2112 - ELECTRICAL SYSTEM: Programming failure - chassis with cummins engine and an allison transmission
  • KC-2116 - ENGINE AND ENGINE COOLING: Nox sensor troubleshooting guide - us10+obd13 and newer emissions.
  • KC-2143 - VEHICLE SPEED CONTROL: (back office) - cruise control inoperative after updating software vecu5 without esp package (uesp).
  • KC-2157 - FUEL SYSTEM, GASOLINE: Aftertreatment hydrocarbon injector (ahi) troubleshooting guide - us10+obd13 and newer emissions.
  • KC-2158 - ENGINE AND ENGINE COOLING: Selective catalytic reduction (scr) muffler troubleshooting guide - us10+obd13 and newer emissions.
  • KC-2165 - ENGINE AND ENGINE COOLING: Def pump troubleshooting guide - us10+obd13 and newer emissions.
  • KC-399 - ELECTRICAL SYSTEM: Vehicle overspeed warning comes active at a lower speed than expected; vehicle overspeed warning in driver information display (did) - model year 2018 and newer with new style instrument cluster.
  • KC-405 - POWER TRAIN: Warranty automated manual transmission ( amt, i-shift, mdrive ) control housing assembly; guidelines for filing a claim for chassis return visit with transmission issues after a repair requiring control housing removal and reinstallation -
  • KC-561 - ENGINE AND ENGINE COOLING: 11l, 13l, and 16l engine oil analysis specifications - us10 and newer emissions
  • KC-735 - EQUIPMENT: Premium tech tool (ptt) - message for data mismatch, product configuration mismatch; instruction to run an accessory kit displayed when attempting to run diagnostics for diagnostic trouble codes (dtc) or programming - us10+obd13 and newer e
  • KC-736 - ENGINE AND ENGINE COOLING: (back office only) - engine brake vibration when in high setting - 13l engine with variable geometry turbo ( vgt ) - us17 and newer emissions (common rail fuel system).
  • KC-745 - POWER TRAIN: Automated manual transmission ( amt ) i-shift / mdrive - ribbon harness replacement - speed sensor bolts, possible fault codes P1058 - 21 or mid 130 pid 161 fmi 1
  • KC-750 - ENGINE AND ENGINE COOLING: Us10 emission engines - diagnostic trouble code ( dtc ) spn 1231 fmi 9 troubleshooting.
  • KC-751 - POWER TRAIN: Vehicles equipped with an automated manual transmission model d or f ( amt-d, amt-f ) - transmission oil leakage from transmission input shaft seal or output shaft seal - us10 and newer emissions, common model years 2010 and newer.
  • KC-2149 - ENGINE AND ENGINE COOLING: Particulate matter (pm) sensor troubleshooting guide - us14+obd16 and newer emissions
  • KC-2157 - ENGINE AND ENGINE COOLING: Aftertreatment hydrocarbon injector (ahi) troubleshooting guide - us10+obd13 and newer emissions
  • KC-2158 - ENGINE AND ENGINE COOLING: Selective catalytic reduction (scr) muffler troubleshooting guide - us10+obd13 and newer emissions
  • KC-399 - VEHICLE SPEED CONTROL: Vehicle overspeed warning comes active at a lower speed than expected; vehicle overspeed warning in driver information display (did) - model year 2018 and newer with new style instrument cluster
  • KC-561 - ENGINE AND ENGINE COOLING: 11l, 13l, and 16l engine oil analysis specifications - us10 and newer emissions
  • KC-663 - ENGINE AND ENGINE COOLING: Emcon (spark assist) engine aftertreatment system troubleshooting check sheet - us07 emissions
  • KC-644 - ENGINE AND ENGINE COOLING: Manual compression test adapter for engines with stainless steel injector sleeves (conical tip injectors) - us07 and newer emissions, model year 2008 and newer
  • KC-627 - EQUIPMENT: Premium tech tool ( ptt ) training materials and support tools
  • KC-2172 - UNKNOWN OR OTHER: No start condition after over the air programing - vecu5 no start "safe state"
  • KC-2171 - ENGINE AND ENGINE COOLING: Temperature sensor troubleshooting guide - us10+obd13 and newer
  • KC-2170 - SUSPENSION: Electronically controlled suspension (ecs) losing air pressure
  • KC-2169 - ELECTRICAL SYSTEM: Low voltage disconnect (lvd), function description
  • KC-2165 - ENGINE AND ENGINE COOLING: Def pump troubleshooting guide - us10+obd13 and newer emissions
  • KC-2161 - ENGINE AND ENGINE COOLING: Def pump cycling periodically hours after key off
  • KC-2158 - ENGINE AND ENGINE COOLING: Selective catalytic reduction (scr) muffler troubleshooting guide - us10+obd13 and newer emissions
  • KC-2157 - ENGINE AND ENGINE COOLING: Aftertreatment hydrocarbon injector (ahi) troubleshooting guide - us10+obd13 and newer emissions
  • KC-2131 - ENGINE AND ENGINE COOLING: Use for new vehicles (us21+obd22 emissions) - intermittent diagnostic trouble codes U02A3, U029D, U029E
  • KC-2116 - ENGINE AND ENGINE COOLING: Nox sensor troubleshooting guide - us10+obd13 and newer emissions
  • KC-626 - POWER TRAIN: Mack chassis - vehicles equipped with an automated manual transmission model f ( amt-f, mdrive ), premium tech tool ( ptt ) gearbox calibration failure; gearbox calibration operation stops and fails at 33% when run with transmission removed
  • KC-633 - WHEELS: Mack chassis - front hub with unit-bearings ( unitized wheel bearings ), inspection information and guidelines - commonly model year 2008 and newer
  • KC-648 - UNKNOWN OR OTHER: Mack - pto pump speed calculator
  • KC-651 - EQUIPMENT: Mack dealer support communication - selecting the proper sr area for creating an eservice
  • KC-652 - ENGINE AND ENGINE COOLING: Mack low oil pressure diagnostic process for 11 liter engines
  • KC-659 - FUEL SYSTEM, DIESEL: Mack chassis - oil diluted with fuel; fuel in oil, diagnostic information - all emissions prior to us17+obd16 (common rail fuel system), model year 2017 and older
  • KC-686 - VEHICLE SPEED CONTROL: (back office only) mack chassis - cruise control inoperative after disabling the electronic stability program (esp)
  • KC-698 - ENGINE AND ENGINE COOLING: Mack chassis - diesel exhaust fluid ( def ) system cleaning/flush after def pump failure or system contamination
  • KC-699 - ELECTRICAL SYSTEM: Mack chassis - bendix vendor configuration program ( vcp ) software download information
  • KC-700 - POWER TRAIN: Mack chassis - automated manual transmission model f ( amt-f, mdrive ) - short transmission replacement; calibration and/or shifting problems following replacement of a short transmission - us17+obd2016 and newer emissions, model year 2018
  • KC-714 - ENGINE AND ENGINE COOLING: Mack chassis - diagnostic trouble codes ( dtc's ) - P020113, P020213, P020313, P020413, P020513, P020613, cylinders 1 through 6 injector a open circuit
  • KC-731 - POWER TRAIN: Mack chassis - equipped with an automated manual transmission model d or f (mdrive, amt-d, amt-f) - transmission oil leakage from transmission input shaft seal or output shaft seal - us10 and newer emissions, common model years 2010 and new
  • KC-587 - ENGINE (PWS): Mack chassis - snm15-027 a/c compressor inspection required for warranty repairs
  • KC-2146 - BACK OVER PREVENTION: Mack chassis - front radar supply chain constraints
  • KC-156 - ENGINE AND ENGINE COOLING: Mack chassis - diagnostic trouble code ( dtc ) P02FA illuminating the malfunction indicator lamp (mil) - us17+obd16 and us17+obd18 emissions
  • KC-128 - SUSPENSION: Mack chassis - technical service bulletin 728 - 002 - electronically controlled suspension ( ecs ) level sensor bracket, replacement
  • KC-116 - POWER TRAIN: Mack chassis - equipped with an automated manual transmission ( amt, mdrive ) - transmission grinding when downshifting following installation of a reman transmission or range assembly; range synchronizer (synchro) timing procedure - us07 a
  • KC-354 - ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL: Volvo chassis - certain volvo trucks built after january 11, 2016 may experience an issue with the instrument cluster display
  • KC-286 - UNKNOWN OR OTHER: Mack chassis - fsb 563-008 plugs, pressure protection manifold - new brass plugs for noregon pressure protection manifold (ppm)
  • KC-254 - POWER TRAIN: Mack chassis - equipped with an (amt) mdrive transmission grinding while the range is shifting from (6th to 7th) or (7th to 6th) gear
  • KC-153 - EQUIPMENT: Sb - 230 - 001 v-mac i to v-mac ii conversion kit
  • KC-145 - POWER TRAIN: Automated manual transmission (amt) (spigot bearing) input shaft repair kit and shim kit, part number information, reference guide - us07 and newer emissions, model year 2008 and newer
  • KC-153 - ENGINE (PWS): Sb - 230 - 001 v-mac i to v-mac ii conversion kit
  • KC-124 - POWER TRAIN: Automated manual transmission gearbox will not shift to high range after gearbox repair; mid 130 psid 24 fmi 1, P1072-92 unintentional disengagement of high range - us07 and newer emissions, model year 2008 and newer
  • SLM21-007 - EQUIPMENT: Service literature published and released in july, 2021
  • KC-2112 - POWER TRAIN: Programming failure - chassis with cummins engine and an allison transmission
  • P040200 - ENGINE AND ENGINE COOLING: Engine exhaust gas recirculation 1 valve position flow excessive detected
  • K73241583 - EQUIPMENT: Mack chassis - anthem (an) models - headlight diagnostics and replacement; instructions for non-functioning headlight or turn signal in headlight housing
  • S7432 - EQUIPMENT: Vecu reprogramming
  • S7431 - STEERING: Steering drag link castle nut inspection
  • S7416 - EQUIPMENT: Wait to start icon-cummins l9
  • S7415 - EQUIPMENT: 8x4 gr-air dryer relocation
  • S7413 - ENGINE AND ENGINE COOLING: My13-16 eats replacement-phase 1
  • K12034241 - ENGINE (PWS): Diagnosing performance complaints aset engine
  • K95721429 - ELECTRICAL SYSTEM: V-mac - electric rocker switch (1mr4323m/1mr4324m) failures
  • K12741884 - ELECTRICAL SYSTEM: V-mac iii service software displays runtime error 400 - form already displayed (modality)
  • K59403006 - ELECTRICAL SYSTEM: V-mac - dp - error message #34 - software doesn't match what is in the ecu
  • K35724485 - ELECTRICAL SYSTEM: V-mac dp - error message #13 - access denied, password incorrect
  • K44520645 - ELECTRICAL SYSTEM: V-mac - error message #10 - password mismatch
  • K33864441 - ELECTRICAL SYSTEM: V-mac - vehicle configeration parameters recovery
  • K38438211 - ELECTRICAL SYSTEM: V-mac iii - active code ( mid 128, sid 81 ) after flashing the eecu to step 5
  • K32398290 - ELECTRICAL SYSTEM: V-mac iii - pto does not operate
  • K75115306 - ENGINE AND ENGINE COOLING: V-mac iii engine cranks but no start
  • K00539104 - ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL: V-mac - speedometer not working after reprograming
  • K10355880 - ENGINE AND ENGINE COOLING: V-mac iii - severe engine stumble
  • K33625923 - BRAKES (PWS): V-mac - abs malfunction lamp on - ( eaton abs active code 17-10 / arvin meritor wabco active code 7-4 )
  • K83741526 - ENGINE AND ENGINE COOLING: V-mac - jacobs engine brake works intermittently between 2000 to 2100 rpm
  • K26111730 - EQUIPMENT:ELECTRICAL: V-mac iii - smart fan will not disengage
  • K11065398 - ENGINE AND ENGINE COOLING: Mack chassis - crankcase ventilation ( ccv ) oil leaks - fsb 257 - 004, fsb 257 - 006 - us14 and us15 emissions
  • K36340146 - ELECTRICAL SYSTEM: Tech tool returns error code 140 failed to run on-vehicle test; programming, calibration, or test operations fail in premium tech tool (ptt), ptt displays control unit information correctly - us10+obd13 and newer emissions, common model yea
  • K24413634 - ELECTRICAL SYSTEM: Mack chassis - diagnostic trouble code ( dtc ) / fault code spn 1231 fmi 9 inactive on dtc readout, counts in multiples of three - us10 emissions.Reworded for clarity, added link to related cbr solution.
  • K11533602 - ELECTRICAL SYSTEM: Diagnostic tool ( j-pro, premium tech tool ( ptt ) ) displays incorrect timestamp for diagnostic trouble code ( dtc ) / fault code occurrences; system date and time information.Improved title and description for better searchability
  • K93039325 - FUEL SYSTEM, GASOLINE: Mack chassis - diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair - us10 and newer; includes us17 chassis (ghg17 only document in development)
  • K91214678 - POWER TRAIN:MANUAL TRANSMISSION: Automated manual transmission ( amt ) faults - diagnostic trouble codes ( dtcs ) P1052 - 18 , pid 33 fmi 5 intermittent fault in cold weather.Updated with new information and procedure
  • 593-013-03 - ELECTRICAL SYSTEM:STARTER ASSEMBLY:SOLENOID: Mack trucks inc, : bulletin information regarding the grade gripper solenoid, replacement chu, cxu, gu, td. *lj
  • 513-001-01 - SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE: Mack trucks, inc.: field service bulletin trucks: certain mack ,chu, cxu,and gu trucks equipped with the basic esp package and built between january 1,2010 and november 9, 2014 needs reprogramming of the brake electronic control unit. *l
  • 284-057-01 - ELECTRICAL SYSTEM:SOFTWARE: Mack trucks, inc. : field service bulletin information regarding, high soot output engines may experience rough running at lower than normal base idle speed. Software has been released, affected engines are mp7& mp8 built between feb- march
  • SB-631002 - VISIBILITY:WINDSHIELD: Mack truck: windshield installation (rope-pull method)-cxu, chu, gu, cxp, ctp, cxn, chn, cx, ch, ct, cv and cl models. Mack trucks now uses a rope pull windshield glass installation method on current production conventional models. Thi
  • 231001 - FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS: Installation of thermal heat sleeve on fuel return line. *jb
  • 563 - ENGINE AND ENGINE COOLING:ENGINE: On certain model chassis equipped with an aset ac engine prior to engine serial no. 3o0297, the mounting bolts that secure the vtg actuator flange to the turbine housing on the variable turbine geometry (vtg) turbocharger may loosen in serv
  • 723007 - SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR: The antilock brake system (abs) sensor wire insulation may rub through in the area where the harness is looped and secured to the brake chamber lines at the rear drive axle. This condition may lead to corroded wire strands, resulting in a
  • 662005 - STRUCTURE: To prevent chafing damage that can occur to the battery box cover on a chassis equipped with full fairings, a chassis fairing tie bar has been developed and is available. *tt
  • 555 - ELECTRICAL SYSTEM: On certain chassis manufactured between november 2002 through march 2003 and equipped with an aset ac engine, the turbocharger compressor discharge temperature sensor connector may not have been properly secured during assembly. *tt
  • 561 - ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS: Fan drive idler pulley replacement. *tt
  • 637020 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Heater/air conditioner cab control board fuse. *tt
  • 411010 - STEERING:HYDRAULIC POWER ASSIST SYSTEM: Power steering noise - sheppard m90/100 steering gears. *tt
  • 600200310101 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Air conditioning receiver dryer orientation concern (rev #1). Certain trucks built with aset ac engines between january 1, 2002 and april 10, 2003. *tt
  • 556 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Incorrect receiver/dryer mounting. Models with aset ac engine. *tt
  • 600200310101 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Air conditioning receiver dryer orientation concern. Cx and ch trucks built between january 6, 2003 and april 10, 2003. *tt
  • 264003 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Air conditioner compressor mounting arrangement. Manufactured prior to january 13, 2003. *tt
  • 732005 - EQUIPMENT:ELECTRICAL: Electronic dashboard gauge drop out. Manufactured prior to march 2002. *tt
  • 554 - EQUIPMENT:ELECTRICAL: Vehicle information profiler (vip) version 3.1 software upgrade. Manufactured between 7/99 through 12/2/02. *tt
  • 732005 - EQUIPMENT:ELECTRICAL: Electronic dashboard gauge drop-out. *tt
  • 137011 - STRUCTURE:BODY: Heavy-duty 38,000 lb and 44,000 lb rubber and bronze bushed trunnion brackets. *tt
  • 411009 - STEERING: Sheppard m90/m100 steering gears with auto bleed and auto relief plunger features. *tt
  • 141001 - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: Battery hold-down bolts. *tt
  • 121023 - STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS: Rear crossmember reinforcement. Mack cx, ch and cl with ch/cx style rear crossmembers. *tt *sc
  • SB752001 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Subject regarding temp-a-start set-up and testing procedures, and customer data programming requirements. *tt
  • SB210031 - UNKNOWN OR OTHER: Information introducing the electronc dashboard equipped with an engine oil temperature gauge. *tt
  • SB412005 - STEERING:COLUMN: Subject regarding trw steering column models ca (tilt/telescopic) and ct (tilt only) cam replacement kit - on steering columns used in cx, cv, ch and cl model chassis, the actuating cam may break and result in the inability to adjust the st
  • SB642003 - STRUCTURE: Subject pertaining to cab back-wall trim molding -cl model chassis - on ch model chassis with the cx style interior (manufactured after january 1, 2002) , the trim molding located below the rear window on the cab back-wall trim panel may lo
  • SB611002 - STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS: Subject regarding floor-mounted heat shield 0 cx, cv, ch and cl models. Nlm
  • SB610007 - VISIBILITY:WINDSHIELD: Subject regarding windshield wear tape - cx, cv, ch and cl model cabs. Nlm
  • SB323008 - POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:FLOOR SHIFT: Information on electrostatic discharge, damage to eaton autoshift, generation i swing-arm gear selector.*jb
  • SB642005 - SEATS: Information on cab back wall trim panel wear plate.*jb
  • SB535001 - PARKING BRAKE: Subject regarding park brake control valve replacement. *slc
  • SB231006 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:MOUNTING: Subject regarding a new fuel tank strap webbing material. *slc
  • 121026 - SUSPENSION:FRONT:SPRINGS:LEAF SPRING ASSEMBLY:HANGER,BRACKET: Concerns with frame rail cracks in area of rear spring front hanger bracket.*jb
  • 637019 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Subject regarding air conditioner expansion valve interference with cylinder head, 612 models.*jb
  • SB635005 - VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM: On some models, when the cab climate control is set to the heat mode, cab temperature may not remain stable without frequent adjustment of the temperature control lever. *tt
  • SB610005 - STRUCTURE: Subject regarding cab wind noise in vehicles equipped with high rise sleepers. *slc
  • PI542 - ENGINE AND ENGINE COOLING:ENGINE: Subject regarding rear engine mount cracks. *tt
  • SB231006 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: Information on a new, thicker fuel tank strap material. *tt
  • SB008006 - ELECTRICAL SYSTEM:WIRING:FRONT UNDERHOOD: Subject regarding vip (vehicle information profiler) programming harness. *tt
  • SB668010 - STRUCTURE: On some vehicles equipped with a sleeper, cracks may develop in the upper mounting bolt hole of the frame-mounted sleeper tie rod bracket. *tt
  • PI541 - EQUIPMENT:ELECTRICAL: Subject regarding vehicle information profiler (vip) version 2.2 software upgrade. *tt
  • SB414003 - STEERING:HYDRAULIC POWER ASSIST SYSTEM: Information on replacing power steering hoses used on certain model chassis. *tt
  • PI542 - ENGINE AND ENGINE COOLING:ENGINE: Some model chassis manufactured between 3/26/01 and 6/18/01 may have cracks in the end gusset section of the rear engine mounts. *tt
  • PI541 - EQUIPMENT: Product improvement campaign regrding vehicle information profiler (vip) version 2.1 software upgrade for model chassis manufactured between 7/99 through 6/11/01. *tt
  • SB531008 - SERVICE BRAKES, AIR: Subject regarding back pressure control valve tap-in point. *tt
  • SL412002 - STEERING: Information on the upgraded trw generation ii steering column which provides an additional 20 mm forward tilt of the steering wheel. *tt
  • PI540 - VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM: Subject regarding heater blower motor replacement on model chassis with bergstrom hvac units. *tt
  • SB724004 - ELECTRICAL SYSTEM:WIRING:INTERIOR/UNDER DASH: Subject regarding electronic dashboard and vip connector information. *tt
  • PI540 - VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM: Some model chassis, equipped with bergstrom hvac units, may exhibit broken heater blower motor mounting tabs in service, resulting in the motor coming loose. *tt
  • SB233024 - ENGINE AND ENGINE COOLING:ENGINE: Subject regarding inlet air duct maintenance. *tt
  • SB392003 - POWER TRAIN: Service bulletin information regarding a new shift lever inner booth implemented into production to prevent gear shift lever disengagement during severe cold weather. *tt
  • SB635007 - VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM: Subject regarding the improved blow-molded hvac air duct system designed to improve air distribution to the sleeper area. *tt
  • SB233024 - ENGINE AND ENGINE COOLING:ENGINE: Information pertaining to inlet air duct maintenance. *tt
  • PI541 - EQUIPMENT:ELECTRICAL: On cx, cv and ch model chassis manufactured between 7/99 through 6/11/01, a condition may exist where the vehicle information profiler (v.I.P.) display (with electronic dashboard) contains a version of software that may intermittently displ
  • SB215017 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN: On certain model chassis equipped with kysor fan drives, the air line that runs from the fan drive control valve to the fan drive may be severed by the engine fan blades. *tt
  • SB233022 - ENGINE AND ENGINE COOLING:ENGINE:GASOLINE: Information pertaining to the air cleaner cover fastener retrofit kitfaor various model chassis including cx chassis. *tt
  • SB662003 - STRUCTURE: Service bulletin regarding quarter fender mounting post loosening and rotating on cx, ch, cl, rb, rd6 and mr model vehicles equipped with the mack al suspension. *tt
  • SB724004 - ELECTRICAL SYSTEM:WIRING:INTERIOR/UNDER DASH: Subject regarding electronic dashboard and vip connector information. *tt
  • SC262 - SUSPENSION: Subject regarding trw type 20 edl ball sockets - front steer axles. *tt
  • SC260 - SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP: Subject regarding bendix anti-lock brake system electronic control unit replacement. *tt
  • 700200102901 - SERVICE BRAKES, AIR:ANTILOCK:INTERCONNECTING ASSEMBLY(WIRING): Some trucks may exhibit an abs malfunction lamp on with eaton abs active code 17 - 10 and / or arvin meritor wabco active code 7-4 set. *tt
  • 700200102901 - SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:ABS WARNING LIGHT: Subject regarding vehicles exhibiting abs malfunction lamp. *tt
  • 700200100501 - POWER TRAIN: Subject regarding eaton autoshift swing arm shifter failure. *tt
  • SC262 - POWER TRAIN:AXLE ASSEMBLY: Certain model chassis manufactured between july 1, 1999 through december 10, 1999 and equipped with either an arvinmeritor, dana / spicer or mack front steer axle may have ball sockets that were not manufactured to proper case depth and / o
  • SC262 - POWER TRAIN:AXLE ASSEMBLY: On certain model chassis manufactured between july 1, 1999 through december 10, 1999 and equipped with either an arvinmeritor, dana / spicer or mack front steer axle may have ball sockets that were not manufactured to proper case dept and /
  • SB121026 - SUSPENSION: On certain model chassis equipped with al suspension and 6-mm frame rails, cracks may develop in the frame rail, in the area of the front-rear spring hanger bracket. *tt
  • SB752001 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Subject regarding temp-a-start set-up and testing procedures, and customer data programming requirements. *tt
  • 700200031201 - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: Subject regarding single cb antenna mating connector. *tt
  • SB635006 - VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:WINDSHIELD:ELECTRICAL HEATING ELEMENT: Chassis equipped with a cable operted heater control water valve, difficulty adjusting cab heat temperature may be experience. To eliminate this condition, an improved cab heater temperature control water valve is available. *tt
  • SB642003 - UNKNOWN OR OTHER: On ch model chassis with the cx style interior (manufactured after january 1, 2000), the trim molding located below the rear window on the cab back-wall trim panel may loosen and possibly fall off. *tt
  • SB215012 - ENGINE AND ENGINE COOLING:COOLING SYSTEM: Information regarding the ch water pump support bracket. *mjs
  • SB411006 - STEERING: Information regarding trw steering gear seal kits. *mjs
  • SB411006 - STEERING:GEAR BOX (OTHER THAN RACK AND PINION): Information on trw steering gear seal kits. *tt
  • SB230001 - EQUIPMENT: Information pertaining to the v-mack i to v-mac ii conversion kit which is available through the mack parts system as a cost-effective service alternative for replacing a v-mack i or fic module. *tt
  • SB299004 - ENGINE AND ENGINE COOLING:ENGINE: Subject on the new-type engine rear mounting arrangement. *tt
  • SB232012 - ENGINE AND ENGINE COOLING:COOLING SYSTEM: Subject regarding an improved coolant recovery bottle vent cap arrangement available for certain model chassis that may be experiencing coolant leakage due to excessive agitation of coolant inside the recovery bottle. *tt
  • SB232011 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: Subject regarding heavy-duty radiator tie rod. *tt
  • PI527 - SERVICE BRAKES, AIR:SUPPLY:HOSES, LINES/PIPING, AND FITTINGS: Subject regarding signal line piping to the r12 dc rear axle service brake relay valve. *tt
  • SB541002 - SUSPENSION: Information on installing the new-style height control valve for al suspension built with height control valve and separate pilot dump valve. *tt
  • SB622918 - STRUCTURE:BODY:HOOD: Information on new hood adjustments dimensions. *tt
  • SB733001 - INTERIOR LIGHTING: Information on the new dome lamp door switch for some vehicles. *tt
  • SB726004 - ELECTRICAL SYSTEM:WIRING: Information on the new v-mac iii sealed-terminal mini-relays. *tt
  • SB411007 - STEERING:GEAR BOX (OTHER THAN RACK AND PINION): Information regarding trw tas steering gear's pressure relief poppet readjustment. *tt
  • SB533008 - EQUIPMENT: Information regarding a new-style e-12 treadle valve. *yc
  • 980605-P1506 - SUSPENSION: Subject on al suspensin height control valve linkage rod upgrade, and height control valve travel over center condition. *yc
  • SL19A005 - STRUCTURE: Ch cab lateral motion dampening - non-sleeper cab only. *tw
  • 17B002 - STRUCTURE:FRAME AND MEMBERS: Loose fuel tank steps on ch model chassis equipped with chassis side fairings. *tw
  • 19U004 - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER: Refrigerator cabinet modifications. *jd
  • 21K021 - STRUCTURE:BODY:HOOD: Ch and cl hood adjustment. *tw
  • RCL/SC248 - POWER TRAIN:DRIVELINE:DRIVESHAFT: The driveshaft center bearing hanger bracket(s) used to mount the center bearing support assembly on ch model chassis may crack and subsequently break due to bending fatigue. To prevent damage, replacement of the center bearing hanger bra
  • RCL/SC248 - POWER TRAIN:DRIVELINE:DRIVESHAFT: The driveshaft center bearing hanger bracket(s) used to mount the center bearing support assembly on ch model chassis may crack and subsequently break due to bending fatigue. To prevent damage, replacement of the center bearing hanger bra
Vehicle Documentation
no relevant documents
Most Recent Consumer Complaints and Accidents
CrashFireTowedInjuredDeathsFailure
Date
CrashFireN None12 Dead20180627

Fire

NoNoN 1 InjuredNone19980203

Seat belt failed to restrain consumer during accident, resulting in injury.

Common OBD-II Error Codes
  • P1058 [1] P1058
  • U029D [1] Lost Communication With NOX Sensor "A"
  • U029E [1] Lost Communication With NOX Sensor "B"
  • U02A3 [1] U02A3
  • P0201 [1] Injector Circuit Malfunction - Cylinder 1
  • P0202 [1] Injector Circuit Malfunction - Cylinder 2
  • P0203 [1] Injector Circuit Malfunction - Cylinder 3
  • P0204 [1] Injector Circuit Malfunction - Cylinder 4
  • P0205 [1] Injector Circuit Malfunction - Cylinder 5
  • P0206 [1] Injector Circuit Malfunction - Cylinder 6
  • P02FA [1] Diesel Intake Air Flow Position Sensor Minimum/Maximum Stop Performance
  • P1072 [1] P1072
  • P1052 [1] P1052

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.