FSB-234-019
Service Bulletin Details
Public Details for: FSB-234-019
Mack truck: mounted outside of frame rail, is new fuel tank ventilation filter mounting sleeve, using fuel tank j bracket huck fasteners and to increase protection against fuel injector tip erosion. Model chu, cxu, gu, td. *pe
- 2015 - 2014 - 2013 - 2012 - 2011 - 2010 - 2009 - 2008 - 2007 - 2006 -
Models from 2015
2015 MACK PINNACLE (CXU) |
Models from 2012
2012 MACK GRANITE (GU) |
2012 MACK PINNACLE (CHU) |
2012 MACK PINNACLE (CXU) |
2012 MACK TD |
Models from 2010
2010 MACK CHU |
2010 MACK CXU |
2010 MACK GU |
2010 MACK TD |
Models from 2009
2009 MACK CHU |
2009 MACK CXU |
2009 MACK GU |
Models from 2008
2008 MACK CHU |
2008 MACK CXU |
2008 MACK GU |
Models from 2007
2007 MACK CHU |
2007 MACK CXU |
2007 MACK GU |
Models from 2006
2006 MACK CHU |
2006 MACK CXU |
2006 MACK GU |
Field Service Bulletin Trucks Mack Trucks, Inc. Greensboro, NC USA This Field Service Bulletin replaces FSB 234-019 dated 6.2014. SB-10055975-2314 Date Group No. Release Page 6.2014 234 019 02 1(6) Dual Fuel Tanks Ventilation Filter Kit CHU, CXU, GU, TD FSB 234-019, Dual Fuel Tanks Ventilation Filter Kit (June 2014) MACK Trucks has introduced a new fuel tank ventilation filter mounting sleeve (part number 21043123) that mounts on the outside of the frame rail using the fuel tank J bracket huck fasteners. The fuel tank vent filter has been implemented for increased protection against fuel injector tip erosion. This new sleeve offers simplified servicing of the filter due to the location. Sleeves (2 per filter) 21043123 should be used in place of the mounting bracket and hardware in kit 85136403 to mount the filter on the outside of the frame rail next to the fuel tank. Note: To ensure the effectiveness of the fuel tank ventilation filter system, the fuel tank ventilation filter must be changed at the same interval as the engine air filter. With this kit, the fuel tank ventilation filter is mounted directly to the fuel tank J- bracket. The kit contains all parts needed for installation on the J-bracket of one tank, therefore two kits and four sleeves are required for dual tank applications. PV729-FSB234-019_M USA65902 Mack Trucks, Inc. Field Service Bulletin Date 6.2014 Group No. Release 234 019 02 Required Parts Note: Due to various tank and deck plate configurations, some routing and clipping hardware may not be used. W2081796 1. Bracket Fastener (2) (not needed) 7. Hose Adapter 2. Lock Nut (2) (not needed) 8. Extension Hose 3. Tie Strap Retainer (not needed) 9. Shield (not needed) 4. Tie Strap 10. Filter Housing 5. Existing Fuel Tank Vent Hose 11. Filter Housing Retainers 6. Bracket (not needed) 12. Shield Fastener (4) (not needed) Page 2(6) Mack Trucks, Inc. Field Service Bulletin Date 6.2014 Group No. Release 234 019 02 Procedure You must read and understand the precautions and guidelines in Service Information, Function Group 20, “Engine Safety Practices” before performing this procedure. If you are not properly trained and certified in this procedure, ask your supervisor for training before you perform it. DANGER Do not attempt to repair or service this vehicle without having sufficient training, the correct service literature and the proper tools. Failure to follow this could make the vehicle unsafe and lead to serious personal injury or death. CAUTION Possible damage to electronic components. Turn the vehicle ignition switch OFF before disconnecting or connecting any electronic components. Failure to de-energize circuits may result in permanent damage to electronic components. Note: Use standard torque values for all fasteners. 1 Disconnect all cables from the negative (ground) battery terminals to prevent personal injury from electrical shock and prevent damage to electrical components. 2 Remove components as necessary to access fuel tank J bracket. 3 Locate a suitable mounting location within 1 m (3 ft) of the fuel tank vent. Install the mounting sleeves (part number 21043123) on the J bracket huck fasteners. W2091647 Page 3(6) Mack Trucks, Inc. Field Service Bulletin Date 6.2014 Group No. Release 234 019 02 4 Install the filter on the mounting sleeves. W2091644 5 Install the hose adapter in the end of the existing fuel tank vent hose. Cut the appropriate length of extension hose. Connect extension hose to adapter and fuel vent filter. Install tie strap in tie strap retainer and secure extension hose with tie strap. Note: Do not leave any low areas or dips in the vent hose although it can be routed in an upward manner initially and then downward to the filter as long as no dips are left in between. 6 Cut approximately 10 cm (4 in) of hose and connect to bottom of fuel vent filter housing. 7 Install components removed to access fuel tank J bracket. 8 Repeat steps for opposite tank. Page 4(6) Mack Trucks, Inc. Field Service Bulletin Date 6.2014 Group No. Release 234 019 02 9 Install replacement engine fuel filter, part number 21763342. W2069497 10 Identify a suitable location on the air filter housing and install the fuel tank ventilation filter label, part number 21807860. W2081800 11 Reconnect all previously removed cables to the negative (ground) battery terminals and remove wheel chocks. Page 5(6) Mack Trucks, Inc. Field Service Bulletin Date 6.2014 Group No. Release 234 019 02 Page 6(6) Reimbursement This repair may be eligible for reimbursement if a product failure was experienced within time and mileage limits of the applicable Warranty coverage. Reimbursement is obtained via the normal claim handling process. Reimbursement UCHP Reimbursement eWarranty Claim Type (used only when uploading from the Dealer Bus. Sys.) W W Primary Labor Code 2341–03–09–02 — 0.4 hrs. 2314H-01-80 — 0.4 hrs. Causal Part 40QE2187 40QE2187 Labor Code MACK Trucks reserves the right to make any changes in design or to make additions to or upon its products without incurring any obligations to install the same on vehicles previously built.