SP 431-021

Service Program
Trucks
Volvo Trucks North
America
Greensboro, NC USA
Date
4.2013
Group
No.
431 021
Release
Page
01
1(6)
Transmission ECU Programming
OBD2013, D11H, D13H, D16H
VHD, VN
SP 431-021, Transmission ECU Programming
(April 2013)
Information
Software updates with enhancements are available for the Transmission Electronic Control
Unit (TECU). This software update has been released to resolve issues for loss of
calibration and the ability to enable single PTO functionality.
Required Tools
Premium Tech Tool version 2.01.45 or higher
Diagnostic Connector 88890304
Communication Interface 88890300 with firmware 1.12.0.2 or higher
Procedure
DANGER
Do not attempt to repair or service this vehicle without having sufficient training, the correct
service literature and the proper tools. Failure to follow this could make the vehicle unsafe
and lead to serious personal injury or death.
1 Verify service program eligibility by checking service program status in eWarranty.
2 Connect Premium Tech Tool (PTT) to the vehicle diagnostics connector using the 16 pin
OBD cable 88890304 and Communication Interface 88890300. Connect the PC to a
functional LAN or modem connection and a 120 Volt AC source (do not use intermediate
storage).
3 Turn the ignition switch “ON” and Identify Vehicle is displayed.
USA58437
PV729-SP431-021
English
Volvo Trucks North America
Service Program
Date
4.2013
Group
No.
Release
431
021
01
4 Once the vehicle has been identified, enter the Work Order Number information, then click
Start Work.
W2079940
5 From the Main Menu select Program and then Program Electronic Control Unit 1700-0803-39. Then click Start.
W2079941
Page
2(6)
Volvo Trucks North America
Service Program
Date
4.2013
Group
No.
Release
431
021
01
6 Select Transmission ECU (TECU) from the list.
W2079943
Page
3(6)
Volvo Trucks North America
Service Program
Date
4.2013
Group
No.
Release
431
021
01
7 Select Program to update the electronic control unit with the latest software.
W2079942
8 Certain conditions must be met to continue with programming: battery voltage above 10v,
parking brake applied, and ignition key in ON position with engine not running. When all
conditions have been met, click Continue to proceed with programming.
W2080113
9 When programming is complete, click Exit to return to Main Menu.
Page
4(6)
Volvo Trucks North America
Service Program
Date
4.2013
Group
No.
Release
431
021
01
10 Once TECU programming is complete, select Calibrate from the Main Menu. Select 432007-03-01 Transmission and clutch, pulling position and click on Start
W2079944
11 When calibration is complete, clear any diagnostic trouble codes and Finish Work.
Page
5(6)
Volvo Trucks North America
Service Program
Date
4.2013
Group
No.
Release
431
021
01
Reimbursement
This repair is covered by an authorized Service Program. Reimbursement is
obtained via the normal claim handling process.
Claim Type (used only when uploading from the Dealer Bus. Sys.)
B
Recall Status
Vehicle inspected, repair not required
1- Inspected
OK
Vehicle repaired per instruction
2- Modified
per
instruction
Labor Code
Primary Labor Code
43122-0-02
— 0.4 hrs.
Time to take charge and determine campaign status
17003–0–0
— 0.3 hrs.
Causal Part
3092515
Authorization Number
SP431021
Expiration Date
30-SEPT2013
Note: Take Charge Time is not included in the Labor Code for this operation. Take charge
may be eligible but can only be used once per repair visit. If vehicle is having other warranty
repairs performed, take charge should be charged to the warranty repair, otherwise take
charge can be charged to this service program.
Page
6(6)