MC110322

9/27/23, 3:00 PM
11 03 22_SERVICE ACTION: Replace Intake Camshaft
SIB 11 03 22
SERVICE ACTION: Replace Intake Camshaft
2023-09-14
This Service Information Bulletin replaces SIB 11 03 22 dated Jan 12, 2023
What’s New:
Revised Notice under Parts section.
Removed Collect & Return section due to expired eligibility period.
Revised procedure section
MODEL
Model
K67
Model Description
S 1000 RR
The affected vehicles have been marked with campaign number 0011510000 in AIR.
In order to determine if a specific vehicle is affected by this campaign it will be necessary to verify the
vehicle VIN in AIR (Aftersales Information Research). Based on the response of the system, either proceed
with the repair or take no further action. Please note, open campaigns or vehicle stops may not appear in
DCS Warranty Vehicle Inquiry or sales systems until 24-72 hours after they are announced, therefore AIR is
always the recommended method for determining open campaigns and vehicle stops.
SITUATION
During the production of the intake camshaft there was a change in the coolant used to prevent localized
overheating of parts of the camshaft. Because of this, certain parts of the camshaft may have a changed
surface hardness that can result in increased wear of the rocker arms and camshaft over time.
PROCEDURE
For vehicles that have not yet been delivered, the service action must be completed before vehicle
handover. If the service action cannot be completed due to a parts shortage, the service action then must be
performed during the next possible workshop visit when parts become available. In such instances, it is
essential to inform the customer of the situation.
In all instances in which the vehicles have already been handed over to customers, the customers must be
made aware of the situation described above and asked to have the Technical Campaign carried out.
The intake camshaft is to be replaced with a new intake camshaft. Following the removal of the intake
camshaft, the rocker arms on the intake side must also be inspected for initial damage and replaced where
required.
The replacement of the intake camshaft and inspection of the rocker arms on the intake side must be
carried out according to the repair instructions found in AIR “00 60 403 — Replacing the intake camshaft
and inspecting the rocker arms”. A possibly required replacement of the rocker arms on the intake side must
be carried out according to the repair instructions found in AIR “00 60 404 — Replacing the rocker arms of
the intake camshaft”.
Copyright ©2023 MOTORRAD USA, a division of BMW of North America, LLC. All Rights Reserved
about:blank
1/5
9/27/23, 3:00 PM
11 03 22_SERVICE ACTION: Replace Intake Camshaft
PARTS INFORMATION
NOTICE: There are currently limited camshafts available worldwide. Once parts become available orders
have to be placed through the Campaign system (YOCV) information listed below. Only schedule
appointments with customers after you have received the inlet camshaft.
Orders can be placed with the special campaign ordering process outlined below and will be released as
parts arrive. This new process will be used for the entire campaign.
PLEASE FOLLOW THE BELOW PROCEDURE FOR ORDERING PARTS. IDS TICKETS ARE NOT NECESSARY TO
OBTAIN PARTS. Each VIN can only be ordered once. Do not place an order for a customer’s bike unless the bike is at the
dealership or the customer has scheduled an appointment.
YOCV Campaign Number: 3103994545
Parts for this category should be ordered using the “YOCV Campaign” order type function in DCSnet.
Attached you will find step by step instructions for placing this order with this order type. You will need to
order by the below campaign number using the full VIN of the relevant motorcycle.
Only the Intake Camshaft will be allocated through the Campaign System. The remaining required parts are
common parts and should be ordered by dealers as needed through normal parts ordering process.
If you have an ordering issue using the above process, please open an IDS Ticket including the VIN and
detailed description.
Order using the YOCV Campaign number: 3103994545
11 12 8 358 963
Intake camshaft
QTY 1
Regular part ordering process:
Obtain and confirm the part numbers for your specific vehicle by entering the chassis number in ETK which
takes into account specific equipment and/or options.
Additional parts like gaskets, hardware and chemicals may be required for the complete repair.
Replacing intake camshaft (only)
Part Number (Replacing intake camshaft)
11 12 7 726 964
Set of O-rings
13 62 8 658 854
O-ring (18.2×2.5)
07 11 9 909 546
O-ring (37.82×1.78)
13 64 7 675 557
O-ring for fuel injectors
13 53 9 480 898
O-ring for fuel pressure line
07 11 9 963 252
Sealing ring
11 31 7 924 590
Sealing ring
11 42 7 721 779
Oil filter
QTY 1
QTY 2
QTY 2
QTY 4
QTY 1
QTY 1
QTY 1
QTY 1
Part Number AS NEEDED (Replacing intake camshaft)
11 34 - --- --Adjusting plate (Valve shim)
11 31 5 A65 7F5
Timing chain tensioner
11 12 9 480 983
Gasket set for cylinder head cover and secondary air system
As Needed
As Needed
As Needed
Copyright ©2023 MOTORRAD USA, a division of BMW of North America, LLC. All Rights Reserved
about:blank
2/5
9/27/23, 3:00 PM
11 12 8 520 212
11 03 22_SERVICE ACTION: Replace Intake Camshaft
ISA screw with bush
As Needed
Replacing intake camshaft and rocker arms
Part Number (Replacing intake camshaft and rocker arms)
11 33 8 389 397
Rocker arm
07 11 9 963 073
Sealing ring
11 12 7 726 964
Set of O-rings
13 62 8 658 854
O-ring (18.2×2.5)
07 11 9 909 546
O-ring (37.82×1.78)
13 64 7 675 557
O-ring for fuel injectors
13 53 9 480 898
O-ring for fuel pressure line
07 11 9 963 252
Sealing ring
11 31 7 924 590
Sealing ring
11 42 7 721 779
Oil filter
QTY 8
QTY 1
QTY 1
QTY 2
QTY 2
QTY 4
QTY 1
QTY 1
QTY 1
QTY 1
Part Number AS NEEDED (Replacing intake camshaft and rocker arms)
11 34 - --- --Adjusting plate (Valve shim)
11 31 5 A65 7F5
Timing chain tensioner
11 12 9 480 983
Gasket set for cylinder head cover and secondary air system
11 12 8 520 212
ISA screw with bush
As Needed
As Needed
As Needed
As Needed
NOTICE:
If the sealing ring for the timing chain tensioner (11 31 7 924 590) is not available, the complete timing chain
tensioner (11 31 5 A65 7F5) must be replaced instead. The new timing chain tensioner already includes a
new sealing ring.
The set of cylinder head cover seals (11 12 9 480 983) and the ISA screws with bush and seal (11 12 8 520
212) must only be replaced if damaged.
Chemicals Oil/Coolant IF NEEDED can be claimed under sublet 04.
CLAIM INFORMATION
Please submit claims via the normal claim process using the information below.
Defect code
00 11 51 00
Replacing the intake camshaft
00
Replacing intake camshaft (only)
Labor Operation (Replacing intake camshaft)
00 60 403
Replacing intake camshaft and checking rocker arms
+00 60 903
Replacing intake camshaft and checking rocker arms
46 52 510
Mounting and dismounting the rear-wheel stand with special
34 FRU
33 FRU
1 FRU
Copyright ©2023 MOTORRAD USA, a division of BMW of North America, LLC. All Rights Reserved
about:blank
3/5
9/27/23, 3:00 PM
11 03 22_SERVICE ACTION: Replace Intake Camshaft
tools (for motorbikes without a center stand)
Labor Operation AS NEEDED (Replacing intake camshaft)
11 34 504
Adjusting valve clearance (Cylinder head cover removed)
11 30 501
Adjusting ignition timing (Cylinder head cover removed)
9 FRU
3 FRU
Replacing intake camshaft and rocker arms
Labor Operation (Replacing intake camshaft and rocker arms)
00 60 403
Replacing intake camshaft and checking rocker arms
+00 60 903
Replacing intake camshaft and checking rocker arms
+00 60 904
Replacing rocker arms on intake camshaft
46 52 510
Mounting and dismounting the rear-wheel stand with special
tools (for motorbikes without a center stand)
Labor Operation AS NEEDED (Replacing intake camshaft and rocker arms)
11 34 504
Adjusting valve clearance (Cylinder head cover removed)
11 30 501
Adjusting ignition timing (Cylinder head cover removed)
34 FRU
33 FRU
4 FRU
1 FRU
9 FRU
3 FRU
FRUs includes all repair procedures to complete the task with allowance for necessary ancillary tasks (e.g.,
visual inspection, lubrication, cleaning parts etc.) and administrative tasks.
Labor operation code 00 60 403 is a Main labor operation. If you are using a Main labor code for another
repair, use the Plus code labor operation instead.
QUESTIONS REGARDING THIS BULLETIN
Technical inquiries
Warranty inquiries
Parts inquiries
Contact the BMW Technical Support Group via TSARA
Submit an IDS ticket to the Warranty Department
Submit an IDS ticket to the Motorrad Parts Department
Supporting Materials
picture_as_pdf 11 03 22 Replace Intake Camshaft.pdf
picture_as_pdf How to Use YOCV Campaign Order.pdf
Copyright ©2023 MOTORRAD USA, a division of BMW of North America, LLC. All Rights Reserved
about:blank
4/5
9/27/23, 3:00 PM
11 03 22_SERVICE ACTION: Replace Intake Camshaft
Copyright ©2023 MOTORRAD USA, a division of BMW of North America, LLC. All Rights Reserved
about:blank
5/5
How To Use the YOCV Campaign Order Type
Step 1: Access to YOCV Order Type in DCS.
Step 2: Enter the Correct Campaign Number, Full VIN & Click Send.
Campaign Number:
USE CORRECT CAMPAGIN
FROM ABOVE TABLE
ENTER THE FULL VIN
© 2023, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third
parties for distribution. All pricing subject to change.
Page | 6
Step 3: This method of ordering:
• Does not immediately show the parts on order through that “Campaign Number” and VIN
combination.
• Will only accept orders with a valid combo of Campaign Number and VIN that hasn’t already
been used.
•
Clicking on Order allows you to see parts on order after order is successfully sent
© 2023, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third
parties for distribution. All pricing subject to change.
Page | 7