Mitsubishi Fuso Fe640 2001

• Recall 81397 [USA]: The purpose of this standard is to reduce deaths and injuries from motor vehicle crashes by providing adequate illumination of the roadway.
  Mitsubishi fuso truck of america (mfta) is recalling 156 halogen sealed beam high beam headlamp assemblies sold between october 24, 2007 and december 2, 2008 for use as replacement equipment for certain mitsubishi fuso trucks. These lamps fail to conform to the sae standards or recommended practices referenced in table i of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment."
  mfta will notify owners and replace the headlamps free of charge. The safety recall began on april 15, 2009. Owners may contact mfta at 1-856-467-4500.
  mfta's recall no. C1003910.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 82015 [USA]: The shift control lever may become inoperative, or the physical shift lever position on the shift lever housing gear indicator may not match the actual gear selection at the transmission.
  Mitsubishi fuso is recalling 15,549 my 1999-2004 fe639, fe649, and fg639 trucks; my 2001-2004 fe640, and my 2003-2004 fh210 trucks equipped with automatic transmissions. Normal heat emanating from the exhaust pipe may cause the automatic transmission shift linkage to deform. The effort required to operate the automatic transmission shift control lever may increase if the linkage binds due to the deformation.
  dealers will install a modified automatic transmission shift control lever assembly free of charge. The recall began on august 6, 2008. Owners may contact mitsubishi fuso at 1-856-467-4500.
  mitsubishi fuso recall no. C1003610.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 37401 [USA]: The engine could stall and would not restart increasing the risk of a crash.
  On certain trucks, the cylinder head idler gear bushing may have been improperly machined, causing excessive stress on the cylinder head idler gear shaft. Continued operating in this condition could cause the idler gear shaft flange to break and generate abnormal engine noise or engine oil leaks.
  on vehicles with less than 15,000 miles, if the idler gear and bushing assembly, idler gear shaft and bolt will be replaced. If the mileage is more than 15,000 miles, the inside diameter of the idler gear bushing will be measured and if the bushing measures more than 32.043mm (1.262"), the idler gear and bushing assembly, idler gear shaft and bolt will be replaced. The recall began on august 13, 2007. Owners may contact mitsubishi fuso at 1-856-467-4500.
  mitsubishi fuso recall no. C1002210.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 50027 [USA]: The bolt could break, causing the engine to stall and not restart, increasing the risk of a crash.
  On certain medium duty trucks, the cylinder head idler gear shaft bolt may have been insufficiently tightened during initial assembly. Continued operation in this condition could cause the bolt to loosen, resulting in abnormal noise from improper gear alignment.
  dealers will check the idler shaft bolt. If the bolt cannot be removed by hand, a modified idler shaft bolt will be installed. If the bolt is loose enough to be removed by hand, a new idler gear, idler shaft, and a modified idler shaft bolt will be installed. The recall began on december 20, 2005. Owners may contact mitsubishi fuso at 1-856-467-4500.
  mitsubishi fuso recall no. R3150410.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 61536 [USA]: If the vehicle is continually operated in this condition, the bracket may break apart, causing the transmission to drop out of alignment with the drive train.
  On certain medium duty trucks, the rear engine support bracket is composed of materials of insufficient strength. Normal vehicle vibrations may cause the bracket to crack.
  dealers will install a modified rear engine support bracket. The recall began on september 26, 2005. Owners should contact mitsubishi fuso at 1-856-467-4500.
  mitsubishi fuso recall no. C1000110.Customers can also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 61559 [USA]: The effort required to operate the a/t shift control lever may increase if the linkage binds due to rust build-up. the shift control lever may become inoperative, or the physical shift lever position on the shift lever housing gear indicator may not match the actual gear selection at the transmission.
  On certain medium duty trucks, rust build-up on the automatic transmission (a/t) shift linkage may cause the linkage to bind. Rust build-up is accelerated in geographic locations that are situated near large bodies of salt water, or in regions with heavy snow/ice melting compound usage in winter months.
  dealers will install a modified a/t shift control lever assembly. The recall began on september 26, 2005. Owners may contact mitsubishi fuso at 1-856-467-4500.
  mitsubishi fuso recall no. C0028810.Customers can also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 56305 [USA]: If this condition occurs in the area of the fuel injection pump, the engine starter could short circuit if the clamp drops onto the starter terminal. this could prevent the engine from starting. excessive heat from the short circuit could cause a fire.
  On certain trucks, the rubber portion of the fuel injection pipe clamps could deteriorate. Normal vehicle operation could cause the deteriorated clamp to loosen and drip.
  dealers will remove each clamp and inspect for rubber deterioration and will replace the clamp if the rubber deterioration is evident. Dealers will replace the attaching hardware and apply adhesive to prevent the bolts/nuts from loosening and inspect for a rubber cap on the starter motor's terminal and install a cap if one is not present to prevent a short circuit. The recall began on january 13, 2005. Owners should contact mitsubishi fuso at 1-877-711-0707.
  mitsubishi fuso recall no. R3125410.Customers can also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 56385 [USA]: In this condition, the parking brake cable may bend and break due to fatigue. the parking brake may become inoperative and the truck may roll and cause a crash, property and personal injuries.
  On certain trucks, the cable end of the parking brake cable, where it attaches to the parking brake lever, is designed improperly. Repeated normal parking brake operation may cause the cable end to become improperly seated in the parking brake lever groove.
  dealers will inspect the parking brake cable for bending or damage at the cable end and install a modified parking brake cable assembly if the cable is bent or damaged at the cable end. If no bending or damage exists, dealers will install a cable retainer on the cable end of the parking brake cable. The recall began on january 13, 2005. Owners should contact mitsubishi fuso at 1-877-711-0707.
  mitsubishi fuso recall no. C0021610.Customers can also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 2017 [USA]: If the shaft breaks, braking distance would be extended due to the lack of brake booster function, increasing the risk of a crash.
  On some heavy duty trucks, the vacuum pump shaft breaks due to insufficient heat treatment.
  dealers will inspect and replace the vacuum pump shaft assembly. Owner notification began february 15, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact mitsubishi fuso truck at 1-856-467-4500.
  also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 2008172 [Canada]: Engine
  On certain vehicles, normal heat emanating from the exhaust pipe may cause the shift linkage installed as part of campaign 2005194 (C1003610) to bind. As a result, the effort required to operate the automatic transmission shift control lever may increase. In the worst case, the shift control lever may become inoperative, or the transmission gear position indicated on the shift lever housing may not match the actual gear selection at the transmission. Correction: dealers will install a modified shift control lever assembly.

  Show Content

• Recall 2007097 [Canada]: Engine
  On certain trucks, the cylinder head idler gear bushing may have been improperly machined, causing excessive stress on the cylinder head idler gear shaft. Continued operation in this condition could cause the idler gear shaft flange to break and generate abnormal engine noise and/or engine oil leaks. In the worst case, the engine could stall and would not restart. Correction: dealers will inspect and, if required, replace the idler gear and bushing assembly.

  Show Content

• Recall 2005194 [Canada]: Powertrain
  On certain vehicles, rust build-up on the automatic transmission shift linkage, due to an insufficient corrosion inhibiting ability, may cause the linkage the bind. As a result, the effort required to operate the shift control lever may increase. In the worst case, the shift control lever may become inoperative, or the transmission gear position indicated on the shift lever housing may not match the actual gear selection at the transmission. Correction: dealers will install a modified shift control lever assembly. Note: this recall is superseded by recall 2008172.

  Show Content

• Recall 2005195 [Canada]: Engine
  On certain vehicles, the rear engine support bracket is composed of materials of insufficient strength. Normal vehicle vibrations may cause the bracket to crack. If the vehicle is continually operated in this condition, the bracket may break apart. In the worst case, the transmission could drop out of alignment with the driver train. Correction: dealers will install a modified rear engine support bracket.

  Show Content

• Recall 2005291 [Canada]: Engine
  On certain vehicles, the cylinder head idler gear shaft bolt may have been insufficiently tightened during vehicle assembly. Continued operation in this condition could cause the bolt to loosen, resulting in abnormal noise from improper gear alignment. In the worst case, the bolt could break, causing the engine to stall and not restart. Correction: dealers will inspect and, if required, tighten the idler shaft bolt to specifications.

  Show Content

• Recall 2004362 [Canada]: Fuel supply
  On certain vehicles, the rubber portion of the fuel injection pipe clamps could deteriorate. Normal vehicle operation could cause the deteriorated clamp to loosen and drop. If this condition occurs in the area of the fuel injection pump, the engine starter could short circuit if the clamp drops onto the starter terminal. This could prevent the engine from starting. In the worst case, excessive heat from the short circuit could cause a fire. Correction: dealers will replace the outer portion of each of the four fuel injection pipe clamps.

  Show Content

• Recall 2004372 [Canada]: Brakes
  On certain vehicles, the cable end of the parking brake cable, where it attaches to the parking brake lever, is designed improperly. Repeated normal parking brake operation may cause the cable end to become improperly seated in the parking brake lever groove. In this condition, the parking brake cable may bend and/or break due to fatigue. In the worst case, the parking brake may become inoperative. Correction: dealers will inspect and, if necessary, replace the parking brake cable assembly.

  Show Content

• Recall 2002033 [Canada]: Brakes
  Certain heavy-duty trucks. The vacuum pump shaft breaks due to insufficient heat treatment. If the shaft breaks, braking distance would be extended due to the lack of brake booster function, increasing the risk of a crash. Correction: dealers will inspect and replace the vacuum pump shaft assembly.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

The linkage that connect the range selector lever to the automatic transmission was not properly set by the manufacturer, as a result when the selector lever is placed in park the parking pawl will not fully mesh with the parking pawl gear which causes the vehicle to roll when in park, the consumer husband placed his vehicle in park, removed the key nd exited the vehicle, as a result of the vehicle failure the the vehicle rolled forward pinning him and ultimately killing him (mitsubishi fuso fe640t). *nlm

Common OBD-II Error Codes

• C1003 [3] C1003
• C1002 [1] C1002
• C1000 [1] Manufacturer Controlled DTC
• C0028 [1] ISO/SAE Reserved
• C0021 [1] Brake Booster Performance (Subfault)
• C0009 [1] ISO/SAE Reserved