Mitsubishi Fuso Fh210 2004

• Recall 81391 [USA]: The purpose of this standard is to reduce deaths and injuries from motor vehicle crashes by providing adequate illumination of the roadway.
  Mitsubishi fuso truck of america (mfta) is recalling 156 halogen sealed beam high beam headlamp assemblies sold between october 24, 2007 and december 2, 2008 for use as replacement equipment for certain mitsubishi fuso trucks. These lamps fail to conform to the sae standards or recommended practices referenced in table i of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment."
  mfta will notify owners and replace the headlamps free of charge. The safety recall began on april 15, 2009. Owners may contact mfta at 1-856-467-4500.
  mfta's recall no. C1003910.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 82012 [USA]: The shift control lever may become inoperative, or the physical shift lever position on the shift lever housing gear indicator may not match the actual gear selection at the transmission.
  Mitsubishi fuso is recalling 15,549 my 1999-2004 fe639, fe649, and fg639 trucks; my 2001-2004 fe640, and my 2003-2004 fh210 trucks equipped with automatic transmissions. Normal heat emanating from the exhaust pipe may cause the automatic transmission shift linkage to deform. The effort required to operate the automatic transmission shift control lever may increase if the linkage binds due to the deformation.
  dealers will install a modified automatic transmission shift control lever assembly free of charge. The recall began on august 6, 2008. Owners may contact mitsubishi fuso at 1-856-467-4500.
  mitsubishi fuso recall no. C1003610.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 37399 [USA]: The engine could stall and would not restart increasing the risk of a crash.
  On certain trucks, the cylinder head idler gear bushing may have been improperly machined, causing excessive stress on the cylinder head idler gear shaft. Continued operating in this condition could cause the idler gear shaft flange to break and generate abnormal engine noise or engine oil leaks.
  on vehicles with less than 15,000 miles, if the idler gear and bushing assembly, idler gear shaft and bolt will be replaced. If the mileage is more than 15,000 miles, the inside diameter of the idler gear bushing will be measured and if the bushing measures more than 32.043mm (1.262"), the idler gear and bushing assembly, idler gear shaft and bolt will be replaced. The recall began on august 13, 2007. Owners may contact mitsubishi fuso at 1-856-467-4500.
  mitsubishi fuso recall no. C1002210.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 56329 [USA]: Continued operation in this condition could cause the idler gear shaft flange to break and generate abnormal engine noise and/or engine oil leaks. in the worst case, the engine could stall and would not restart, increasing the risk of a crash.
  On certain trucks, the cylinder head idler gear bushing may have been improperly machined, causing excessive stress on the cylinder head gear shaft.
  dealers will measure the inside diameter of the cylinder head idler gear bushing. If the bushing is out of specification, dealers will replace the idler gear bushing, idler gear shaft, and idler gear assembly free of charge. The recall began on december 20, 2005. Owners may contact mitsubishi fuso at 1-856-467-4500.
  mitsubishi fuso recall no. R3150510.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236; (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 61533 [USA]: If the vehicle is continually operated in this condition, the bracket may break apart, causing the transmission to drop out of alignment with the drive train.
  On certain medium duty trucks, the rear engine support bracket is composed of materials of insufficient strength. Normal vehicle vibrations may cause the bracket to crack.
  dealers will install a modified rear engine support bracket. The recall began on september 26, 2005. Owners should contact mitsubishi fuso at 1-856-467-4500.
  mitsubishi fuso recall no. C1000110.Customers can also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 61556 [USA]: The effort required to operate the a/t shift control lever may increase if the linkage binds due to rust build-up. the shift control lever may become inoperative, or the physical shift lever position on the shift lever housing gear indicator may not match the actual gear selection at the transmission.
  On certain medium duty trucks, rust build-up on the automatic transmission (a/t) shift linkage may cause the linkage to bind. Rust build-up is accelerated in geographic locations that are situated near large bodies of salt water, or in regions with heavy snow/ice melting compound usage in winter months.
  dealers will install a modified a/t shift control lever assembly. The recall began on september 26, 2005. Owners may contact mitsubishi fuso at 1-856-467-4500.
  mitsubishi fuso recall no. C0028810.Customers can also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 56302 [USA]: If this condition occurs in the area of the fuel injection pump, the engine starter could short circuit if the clamp drops onto the starter terminal. this could prevent the engine from starting. excessive heat from the short circuit could cause a fire.
  On certain trucks, the rubber portion of the fuel injection pipe clamps could deteriorate. Normal vehicle operation could cause the deteriorated clamp to loosen and drip.
  dealers will remove each clamp and inspect for rubber deterioration and will replace the clamp if the rubber deterioration is evident. Dealers will replace the attaching hardware and apply adhesive to prevent the bolts/nuts from loosening and inspect for a rubber cap on the starter motor's terminal and install a cap if one is not present to prevent a short circuit. The recall began on january 13, 2005. Owners should contact mitsubishi fuso at 1-877-711-0707.
  mitsubishi fuso recall no. R3125410.Customers can also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 52328 [USA]: These conditions could result in the outer bearing generating excessive heat and/or breaking, causing the vehicle to become disabled. the excessive heat could cause a fire.
  On certain trucks trucks equipped with an f040t front axle. The front wheel hub outer bearing lock nut may have been improperly tightened during assembly, and an insufficient amount of grease may have been applied to the outer bearing.
  dealers will inspect the inner and outer front wheel hub bearings, and replace any bearing with signs of damage. The recall began on october 28, 2004. Owners should contact mitsubishi fuso at 1-856-467-4500.
  mitsubishi fuso recall no. R3123510.Customers can also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 2008172 [Canada]: Engine
  On certain vehicles, normal heat emanating from the exhaust pipe may cause the shift linkage installed as part of campaign 2005194 (C1003610) to bind. As a result, the effort required to operate the automatic transmission shift control lever may increase. In the worst case, the shift control lever may become inoperative, or the transmission gear position indicated on the shift lever housing may not match the actual gear selection at the transmission. Correction: dealers will install a modified shift control lever assembly.

  Show Content

• Recall 2007097 [Canada]: Engine
  On certain trucks, the cylinder head idler gear bushing may have been improperly machined, causing excessive stress on the cylinder head idler gear shaft. Continued operation in this condition could cause the idler gear shaft flange to break and generate abnormal engine noise and/or engine oil leaks. In the worst case, the engine could stall and would not restart. Correction: dealers will inspect and, if required, replace the idler gear and bushing assembly.

  Show Content

• Recall 2005194 [Canada]: Powertrain
  On certain vehicles, rust build-up on the automatic transmission shift linkage, due to an insufficient corrosion inhibiting ability, may cause the linkage the bind. As a result, the effort required to operate the shift control lever may increase. In the worst case, the shift control lever may become inoperative, or the transmission gear position indicated on the shift lever housing may not match the actual gear selection at the transmission. Correction: dealers will install a modified shift control lever assembly. Note: this recall is superseded by recall 2008172.

  Show Content

• Recall 2005195 [Canada]: Engine
  On certain vehicles, the rear engine support bracket is composed of materials of insufficient strength. Normal vehicle vibrations may cause the bracket to crack. If the vehicle is continually operated in this condition, the bracket may break apart. In the worst case, the transmission could drop out of alignment with the driver train. Correction: dealers will install a modified rear engine support bracket.

  Show Content

• Recall 2005270 [Canada]: Engine
  On certain vehicles, the cylinder head idler gear bushing may have been improperly machined, causing excessive stress on the cylinder head idler gear shaft. Continued operation in this condition could cause the idler gear shaft flange to break and generate abnormal engine noise and/or engine oil leaks. In the worst case, the engine could stall and would not restart. Correction: dealers will inspect and, if required, replace the idler gear assembly.

  Show Content

• Recall 2004357 [Canada]: Suspension
  On certain vehicles equipped with an f040t front axle, the front wheel hub outer bearing lock nut may have been improperly tightened during initial assembly, and an insufficient amount of grease may have been applied to the outer bearing. These conditions could result in the outer bearing generating excessive heat and/or breaking, causing the vehicle to become disabled. In the worst case, the excessive heat could cause a fire. Correction: dealers will inspect the front inner and outer wheel hub bearings, and replace any bearings with signs of damage.

  Show Content

• Recall 2004362 [Canada]: Fuel supply
  On certain vehicles, the rubber portion of the fuel injection pipe clamps could deteriorate. Normal vehicle operation could cause the deteriorated clamp to loosen and drop. If this condition occurs in the area of the fuel injection pump, the engine starter could short circuit if the clamp drops onto the starter terminal. This could prevent the engine from starting. In the worst case, excessive heat from the short circuit could cause a fire. Correction: dealers will replace the outer portion of each of the four fuel injection pipe clamps.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.