Prevost X3-45 2010

Vehicle Details: Recalls, Investigations, Service Bulletins

Below you will find all available information on the 2010 PREVOST X3-45.

ManufacturerKnown WMI(s)Fuel Type
PREVOST
PREVOST VIN Decoder

Use the box here to look up VINs from PREVOST as well as other manufacturers

#

Sub-models: - X3-45 Vip - X3-45 Coach - X3-45 Commuter - X3-45 Vip Entertainer -

Frequently Asked Questions
  • Are there recalls for the 2010 PREVOST X3-45?
     - There are 29 recall(s) for the 2010 PREVOST X3-45, additional information is below.
NHTSA Mandated Recalls
  • Recall 192257 [USA]: An overheated alternator bearing can increase the risk of a fire.

  • Recall 138426 [USA]: A complete loss of steering would increase the risk of a crash.

  • Recall 133663 [USA]: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.

  • Recall 138324 [USA]: If the fuel tank separates from the vehicle, it could be a road hazard and the vehicle would stall. either scenario increases the risk of a crash.

  • Recall 113447 [USA]: If the power cable electrically shorts against the frame, there would be an increased risk of a fire.

  • Recall 114508 [USA]: The damaged wires may activate the afss and shutdown the engine, increasing the risk of a vehicle crash.

  • Recall 108573 [USA]: The fuel line rubbing may result in abrasion and a fuel leak, increasing the risk of a fire.

  • Recall 113875 [USA]: If the event of a fire, if the pressure tank has previously vented, the system would not be functional to help extinguish the fire, increasing the risk of injury.

  • Recall 103623 [USA]: A damaged seat belt may fail in the event of a crash, increasing the risk of injury to the seat occupant.

  • Recall 101704 [USA]: Once electrically conductive, the material is capable of melting and burning, increasing the risk of a fire.

  • Recall 93732 [USA]: Uncontrollable throttle position may lead to a loss of vehicle control, increasing the risk of a crash.

  • Recall 95642 [USA]: An activation of the afss causes the vehicle to come to an unplanned stop. this could increase the risk of a vehicle crash or personal injury.

  • Recall 94555 [USA]: If this occurs, the afss may activate with no fire present and the stop engine feature will be activated, bringing the vehicle to an unplanned stop, increasing the risk of a crash.

  • Recall 91802 [USA]: If this occurs, the vehicle may stop responding to input from the accelerator pedal, and thus become stopped in traffic, increasing the risk of a crash.

  • Recall 92521 [USA]: If this occurs, the driver may lose control of the vehicle, increasing the risk of a crash. also, a wayward wheel represents a road hazard to other road users.

  • Recall 68899 [USA]: The user of the lift could be injured should the lift move without the restraint belt properly buckled.

  • Recall 2018737 [Canada]: Steering

  • Recall 2017570 [Canada]: Accessories

  • Recall 2015240 [Canada]: Accessories

  • Recall 2015239 [Canada]: Electrical

  • Recall 2015088 [Canada]: Fuel supply

  • Recall 2014544 [Canada]: Brakes

  • Recall 2014149 [Canada]: Seats and restraints

  • Recall 2014056 [Canada]: Electrical

  • Recall 2013059 [Canada]: Other

  • Recall 2013014 [Canada]: Other

  • Recall 2012191 [Canada]: Other

  • Recall 2010087 [Canada]: Other

  • Recall 2014544 [Canada]: Brakes

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • IS-23019 - SUSPENSION: Sway bar collars improvement
  • IS-18106 - STEERING: Kit power steering tank convertion cummins to zf with d13 engine
  • MI16-32 - ENGINE AND ENGINE COOLING: Improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • IS-21072B - ELECTRICAL SYSTEM: Steering gateway. Revision b - pin 2 and 10 were inverted on connector a139
  • MI22-12B - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: b - general update
  • MI22-12A - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: a - erroneous secondary & accessory tanks location.
  • MI22-12 - SERVICE BRAKES, AIR: Air tanks draining sequence
  • IS-17151C - EXTERIOR LIGHTING: Halogen to led fog light replacement kit. Revision: c - advanced kits canceled
  • IS-22902 - WHEELS: Tag axle hub flange - alternate cap screw
  • MI20-08C - EQUIPMENT: Storage and startup guidelines : part number updates
  • IS21-901 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : X3 series envirocare - ions air sanitizer
  • IS21-072A - ELECTRICAL SYSTEM: Steering gateway revision a cancel watch dog removal from efd part of the instruction
  • IS20-925A - VISIBILITY: Central hvac merv filters installation
  • MI18-16B - ELECTRICAL SYSTEM: Bosch hd10 alternator diagnostic guide revision b to avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
  • MI21-06 - FUEL SYSTEM, DIESEL: Diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair ⿿ from us10 to newer engine generation
  • Mi21-07A - WHEELS: Ront & tag axle ⿿ unitized hub bearing end play verification and replacement
  • IS-21901 - EQUIPMENT: X3 series envirocare - ions air sanitizer
  • IS-08080B - EQUIPMENT: Sound selector replacement, vss04 to vss05; when replacing a vehicle sound selector model vss04 with a new sound selector model vss05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new
  • MI20-08C - STRUCTURE: Storage and startup guidelines: periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, prevost recommends foll
  • IS-20925A - POWER TRAIN: Central hvac merv filters installation reva
  • VBC-PREVOST 2 - EQUIPMENT ADAPTIVE/MOBILITY: Bendix m-32qr abs modulator valve replaced by new m-40qr valve.
  • IS-18091A - STEERING: Tie rod 610052 first installation instructions: use these instructions when replacing the drop joint tie rod on s82, s84 / s84u i-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment ne
  • MI20-19B - ENGINE AND ENGINE COOLING: Introducing a new engine coolant into prevost service center network
  • MI20-19A - ENGINE AND ENGINE COOLING: Rev a: mention added concerning ddc series 60 engine sca requirement
  • MI20-19 - EQUIPMENT: Introducing a new engine coolant into service
  • MI17-03 - ELECTRICAL SYSTEM: After the installation of the latest multiplex system update on us10 x3-series coaches, the instrument panel and switches backlighting may stay constantly on due to an output (j1:4) on the a44 module sending constant current to the 114a cir
  • SCi20-16 - ENGINE AND ENGINE COOLING: Fan clutch plate bolts re-torquing
  • MI20-08B - EQUIPMENT: Storage and startup guidelines revision: b parts added to suggested material 08-10-2020
  • IS-20922 - EQUIPMENT ADAPTIVE/MOBILITY: Sigma passenger seats partition kit
  • MI20-12 - STEERING: Jerky, noisy or hard to turn steering gearbox. Hydraulic end limiter adjustment. All models ⿿ equipped with rb bosch/zf servocom or servocomtronic steering gearbox
  • IS-19912B - ENGINE (PWS): Electric fan drive cooling system conversion with delco remy alternator revision : b parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal,
  • IS-20907 - EQUIPMENT ADAPTIVE/MOBILITY: Plexiglass panel behind driver x3
  • MI20-08A - EQUIPMENT: Storage and startup guidelines: rev a: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
  • MI20-09 - EQUIPMENT:OTHER:LABELS: Prevost vehicle disinfection procedure
  • MI20-08 - UNKNOWN OR OTHER: Storage and startup guidelines - all prevost vehicles & volvo 9700
  • IS-20905 - EQUIPMENT: Hand sanitizer dispenser installation
  • IS18909B - VISIBILITY: Item 5060078 was 5002151, items 530175 and 641074 added, some steps added and some updated
  • MI15-24 - EQUIPMENT ADAPTIVE/MOBILITY: Added: power cables for l.H. Side alternator & fan drive breaker box
  • IS-18909A - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to replace a carrier ac compressor with a bitzer's.
  • IS-17151 - LIGHTING (PWS): This instruction sheet explains how to replace halogen fog light to led's
  • IS-19092 - LATCHES/LOCKS/LINKAGES: This instruction sheet explains how to install 780428 door actuator replacement.
  • IS-18091 - STEERING: This instruction sheet explains how to perform the first installation of tie rod 610052 on prevost vehicles equipped with dana s82, s84 / s84u i-beam axles, 1994- today
  • MI18-45A - POWER TRAIN: Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to is-18091 for installation instruction
  • IS-19915 - EQUIPMENT: Mp-1000 multimedia player installation
  • IS-19040 - STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS: Power steering pump discharge hose (pressure) replacement
  • IS-17910A - EQUIPMENT: Message center display (mcd) replacement
  • IS-17905A - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-11003G - EQUIPMENT: This instruction sheet explains how to replace the ?Master id? With ?Mcm? Module
  • SP18-13F - STEERING:LINKAGES:DRAG:LINK:CONNECTION: On the vehicles affected by this bulletin, proceed to the replacement of the drag link.
  • IS-18909 - ENGINE AND ENGINE COOLING: This instruction sheet explains how to replace the carrier ac compressor with a bitzer
  • IS-13009D - STEERING:LINKAGES:DRAG:LINK:CONNECTION: This instruction sheet explains how to install and adjust drag link # 660699
  • IS-11003F - ELECTRICAL SYSTEM: This instruction sheet explains how to replace the "master id with mcm" module
  • SCI18-46 - EQUIPMENT:ELECTRICAL: This service center instructions explains how to install the prevost ultimate entertainment system
  • IS-13009C - STEERING:LINKAGES:DRAG:LINK:CONNECTION: This instruction sheet explains how to install and adjust drag link # 660699
  • IS-18907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install hatches with fan on x3 vehicles.
  • IS-17910 - EQUIPMENT: This instruction sheet explains how to replace the message center display (mcd)
  • IS12010 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to replace the left bell crank using kit 161349
  • MI18-05 - ENGINE AND ENGINE COOLING: This maintenance information explains how to install valve assembly 130009 in replacement of valve 641274
  • MI16-17G - ENGINE AND ENGINE COOLING: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • IS-15003E - ELECTRICAL SYSTEM: This insruction sheet explains how to insall the bosch hd10 24v-150a alternator conversion kit ? Twin bosch mounted on volvo d13 engine
  • MI16-08B - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information presentes the new method of locking the electromagnetic clutch in the event of a failure. These new electromagnetic clutches will feature locking tabs in replacement of the locking bolts.
  • MI18-16A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information presents guidelines to help with the diagnosis of the bosch hd10 alternators
  • SP18-13D - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, proceed to the replacement of the drag link.
  • IS-17905 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-13009B - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install and adjust drag link # 660699
  • SP18-13E - STEERING:LINKAGES:DRAG:LINK:CONNECTION: On the vehicles affected by this bulletin, replace the drag link.
  • MI16-17F - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • WB14-28E - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, replace the ltd, relocate and replace the ir sensor as described in the following procedure.
  • SP14-306D - ENGINE (PWS): On the vehicles affected by this bulletin, replace the engine harness as described in the following procedure.
  • MI1423 - ELECTRICAL SYSTEM:SOFTWARE: A new software version (v1.06) is available to update the cantrak (tire pressure monitoring system) module. This new version will allows a 10 min. Delay before the ?System error not all tires monitored? Message appears in the vehicle clust
  • IS-08080 - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: When replacing a vehicle sound selector model vss04 with a new sound selector model vss05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new vss05 compatible radio unit must also be in
  • SP13-44 - ELECTRICAL SYSTEM: The light switch may operate incorrectly when doors are closed for vehicles affected by this bulletin. Corrective action is presented.
  • MI13-33 - SUSPENSION:MULTIPLE AXLE:TORQUE ARM: This maintenance information explains that polyester reinforced silicone hoses and elbowscan be repalced by aramid reinforced hoses and elbows for improved long term durability, and that constant torque hose clamps for silicone hoses with 5
  • SP13-322 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, relocate the video fuse in the smi box closer to the door for better access.
  • SP13-321 - EQUIPMENT: On the vehicles affected by this bulletin, at next service occasion, open the c69 connector located in the front compartment and check for presence of corrosion. Relocate the connector horizontally.
  • SP13-320 - EQUIPMENT: On the vehicles affected by this bulletin, if needed, the celling panel needs to be removed and material glued again.
  • SP13-319 - SEATS: On the vehicles affected by this bulletin, follow the enclosed procedure to correct surface corrosion on seat pedestals.
  • SP13-318 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : On the vehicles affected by this bulletin, take the following measure to improve dust handling. Seal the evaporator compartment to prevent dust entry, add ribs inside the duct to prevent collapse by the weight of accumulated dust, modify th
  • SP13-314 - STRUCTURE:BODY:DOOR : On the vehicles affected by this bulletin, follow the enclosed procedure to remove corrosion around luggage doors.
  • SP13-324 - EQUIPMENT: On the vehicles affected by this bulletin, an improved 90 degree elbow is available. Proceed to replacement at next service occasion.
  • MI13-06 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: This maintenance information explains that hose clamps with a smaller diameter are available to increase the adjustment range at the upper and lower radiator flexible connections and at the oil cooler connections located under the turbocha
  • SP13-309 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: Multiple hose failures, agreed with customer to replace silicone hose in engine compartment for coaches with volvo engine.
  • SP13-306 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE): On the vehicles affected by this bulletin, replace the exhaust gas recirculation venturi tube and sensor for an improved design.
  • WB12-31B - EQUIPMENT: On the vehicles affected by this bulletin, a new and improved dipstick is available for installation.
  • IS11015B - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to replace power relay p/n 561991 with improved power relay p/n 564218 and relay base p/n 564210
  • IS12047 - STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS: This instruction sheet explains how to install additional restraint for plastic shields over drive axle wheels. Use kit #3200407 to secure the shields to the bus structure.
  • MI15-51 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: This maintenance information explains how to run a n air conditionning performance test
  • WB15-50 - EQUIPMENT:OTHER:LABELS: On the vehicles affected by this bulletin the rear junction box decal located in the right engine compartment is displaying incorrect information regarding the r34 relay voltage. Specifically, the r34 relay should be identified as a 24 v
  • MI15-61 - ENGINE (PWS): This maintrenance infomration explains that the castrol syntrans oil isn?T fully approved for 500 000 miles (800 000 km) extended drain intervals on the volvo i-shift transmission. For this reason, this oil has been downgraded to regular d
  • MI15-18 - EQUIPMENT: This maintenance information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.
  • MI15-24 - EQUIPMENT:MECHANICAL: This maintenance information explains how to perform an inspection of the vehicle power cables. Power cables in poor condition can be the cause of failures and serious damages in the engine compartment.
  • SP15-32 - ELECTRICAL SYSTEM:WIRING: On the vehicles affected by this bulletin, to reduce the possibility of fault codes the dpf differential pressure sensor signal wire needs to be replaced by a single wire from the dpf differential pressure sensor directly to the acm connect
  • SP15-313 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, replace the existing positive booster block and cable terminal by a protected assembly.
  • IS-15003A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to use the bosch hd10 24v-150a altenrator conversion kit
  • IS-17907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the volvo electronic logging device (eld)
  • wb17-16 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, remove selected wires from c15 and c58 of the hvac system wiring, and place them in new connectors c15b and c58b. New connectors have a higher amp rating. We recommend inspecting connectors c15 & c
  • SCI17-35 - ELECTRICAL SYSTEM:SOFTWARE: This internal instruction explains how to bench program the fms gateway module used in the eld (electronic logging device) interface kit for pre-obd13 vehicles.
  • MI15-02 - POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT: This maintenance information presents an improved differential breather kit, identical to the one now used in production. This new breather incorporates a "j" shaped hose that prevents oil leakage and water ingestion while allowing the axle
  • WB14-47B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a software update of ecm (engine control module) and acm (aftertreatment control module) to provide improved temperature-related behaviour. The software will also change urea dosing valve b
  • Mi16-15 - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • IS-14154 - FUEL SYSTEM, GASOLINE: This instruction sheet explains how to modify the support beam (part # 30022 installation)- as part of the x3 fuel tank installation
  • IS-16100 - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: This instruction sheet explains how to install latest radio models
  • IS-15003D - ELECTRICAL SYSTEM: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • MI16-32 - POWER TRAIN:DRIVELINE:CENTER SUPPORT BEARING: Explains that improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • IS-11003A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to replace master id? With ?Mcm? Module
  • WB15-26B - SUSPENSION:REAR:SPRINGS:AIR SUSPENSION SYSTEM: On the vehicles affected by this bulletin the brake hose may come in contact with the air spring support when the front axle is in low or high position, either by kneeling or low-high buoy. Perform an inspection. Depending on the result, ad
  • SP15-21 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, to prevent premature corrosion of the rear junction box components, replace the junction box cover with a late model "central mount" cover.
  • IS-15003B - EQUIPMENT: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • IS-14900 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to replace 562489 dimmer, using kit #069136
  • SP14-05B - ENGINE (PWS): On the vehicles affected by this bulletin, perform a turbo replacement if fault codes 27 fmi 7 or spn641 fmi 7 or P004607 (obd13) are found. Bulletin affects d13h engines with serial number from 984581 up to 1026719, excluded.
  • MI16-15B - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • IS-11003D - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to remplace master id? With ?Mcm? Module
  • MI16-22 - EQUIPMENT ADAPTIVE/MOBILITY: Use this maintenance information procedure to resolve an undesired behaviour on 2008-2012 vehicles. In sleep mode, certain marker lights may remain illuminated.
  • MI16-15A - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • MI12-04C - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintneance informations presents an improved harness and wiring modification procedure to avoid certain fault codes and messages.
  • MI16-16 - ELECTRICAL SYSTEM: This procedure explains how to perform a starter removal and installation, and does apply to melco 105p70 starter part number #21212425.
  • CK17-19A - EQUIPMENT: This conversion kit explains how to remove tgw1 from vehicles using tech tool, no manual vda changes needed. This conversion kit will work for any vehicle equipped with tgw1 up to the vin's listed on the bulletin.
  • IS-11003E - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to remplace master id? With ?Mcm? Module
  • IS-17901 - BRAKES (PWS): This instructions sheet explains how to program a wabco smart trac abs ecu.
  • IS-15003D - ENGINE (PWS): This insruction sheet explains how to insall the bosch hd10 24v-150a alternator conversion kit ? Twin bosch mounted on volvo d13 engine
  • MI16-08 - EQUIPMENT:MECHANICAL: On receiving your kit masters fan clutch you may notice a new method of locking the electromagnetic clutch in the event of a failure. These new electromagnetic clutches will feature locking tabs in replacement of the locking bolts. Applies
  • WB14-47B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a software update of ecm (engine control module) and acm (aftertreatment control module) to provide improved temperature-related behaviour. The software will also change urea dosing valve b
  • WB13-58 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: On the vehicles affected by this bulletin, change the flexible hose at the engine air intake
  • WB13-60 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, a software update for the volvo i-shift transmission is required. Software update has for effect to improve the gear change process to avoid clashing and wear on the split gear. This software updat
  • MI16-17E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternator.
  • IS-15003C - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • IS-08080A - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: When replacing a vehicle sound selector model vss04 with a new sound selector model vss05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new vss05 compatible radio unit must also be in
  • SP15-313 - EQUIPMENT: Summary to be provided on a future date.
  • SP-15-313 - EQUIPMENT: Prevost: some buses need to have protected assembly for replacing of the existing positive booster block and cable terminal. Model 2008-10 x3-45. *pe
  • MI-13-06 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: Prevost: to increase vehicle's performance, a modification of hose clamp for cooling system connection, is recommended. Models 2010-13 h3, 2010-13 h3 vip converted, 2010-13 x3, 2012-13 x3 vip converted, 2010-13 mth xl2 entertainer, 2011 m
  • WB-12-31 - EQUIPMENT ADAPTIVE/MOBILITY: Prevost: information being provided regarding the replacement of dipstick on certain coaches. Models 2009-2013 h3-45, h3-41, x3-45, xl11-45, x3-45. *pe
  • SP-12-01-A - ENGINE (PWS): Prevost: information is being provided regarding two procedure methods of pinning or replacing the double idler gear, on certain vehicles engine, that is necessary. *pe updated 4/5/13. *pe
  • MI-12-11-A - ENGINE (PWS): Prevost: information being provided regarding the modification of d13 us07 engines' improved belt tensioner to prolong belt life. *pe
  • SCI10-02 - ENGINE AND ENGINE COOLING:COOLING SYSTEM: Prevost: installin an air deflector in order to reduce ambient temperature around linnig radiator fan gearbox. *kb
  • WB10-26A - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine correction of the drv control valve air supply circuit. *kb updated on 5/9/2012. *kb
  • WB10-17 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine - turbocharger smart remote actuator (sra) faults. *kb
  • WB10-18 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine oil seepage at unit injector harness pass-through fitting. *kb
  • WB11-15A - FUEL SYSTEM, DIESEL: Prevost: diesel particulate filter (dpf) access door air grille bonding verification. *kb
  • WB11-02 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: replacing t1 bosch alternators and water pump belt tensioners. *kb
  • WB11-01A - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine - aftertreatment hydrocarbon injector (ahi) fuel line fittings - proper tightening verification. *kb
  • SP11-07A - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: engine oil cooler - coolant duct cover leaking inspection/replacement with egr cooler retrofit. *kb
  • WB11-22 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine harness replacement - oil seepage at unit injector pass - through fitting. *kb
  • WB09-25 - ENGINE AND ENGINE COOLING:ENGINE: Prevost: on volvo d13 engines dashboard 'check engine' warning lamp could come on due to code pid 110. Also included model mth xll45e bus model year 2009 *js
  • WB09-24 - FUEL SYSTEM, OTHER:FUEL FILTER: Prevost: check if volvo engines are not equipped with 'davco fuel pro 382' filter are fitted wih two fuel filters. *js
  • WB09-26 - ENGINE AND ENGINE COOLING:ENGINE: Prevost: on volvo d13 engines dashboard 'check engine' warning lamp could come on due to code pid 171. Also included model mth xlii-45e bus shells model year 2009. *js
  • SCI11-11 - UNKNOWN OR OTHER: Prevost: kidde fire extinguisher control head replacement. *kb updated 5/9/2012. *kb
  • MI11-27 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Prevost: 12" brushless condenser fan replacement. Models include xlii mth, and h3vip mth. Model years are 2008-2011. *kb
  • WB10-01A - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine: replacement of copper injector sleeve with conical stainless steel injector sleeve. *kb updated 5/4/2012. *kb
  • WB09-18 - SERVICE BRAKES, AIR: Prevost: tag axle brake actuator replacement. *kb
  • WB10-36A - ELECTRICAL SYSTEM: Prevost: reprogramming of i/o-a & i/o-b modules for implementation of the essential functions to operate the vehicle (basic limp-home functions). *kb
Known Recall Investigations
  • Alternator front bearing failure investigation # PE21011

    Nhtsas office of defects investigation (odi) opened a preliminary evaluation after reviewing field reports concerning alternator front bearing failures that cause elevated temperatures within the engine compartment, resulting in the fire suppression system (fss) activating, immediately shutting the engine down, and rendering the bus inoperable.Analysis of the data provided by prevost car (us) inc. Showed high failure frequency and thermal events. An immediate shutdown of the bus can increase the risk of a crash or injury of bus occupants. In response to this investigation, prevost car (us) inc. And volvo bus corporation decided to conduct recalls 22v-221 and 22v-222. By submitting part 573 defect information reports on april 6, 2022, prevost car (us) inc. And volvo bus corporation notified odi of a safety defect in certain model year (my) 2010-2023 prevost h3-45; x3-45; x3-45 com; h3-45 vip: x3-45 vip and 2020 volvo 9700 vehicles; some of these buses may have experienced thermal events after failure of the alternator front bearing, because the alternator belt continues to turn the alternator after the bearing failure.These recall actions address the safety concern that led to the opening of this investigation.Therefore, with these recall actions, this investigation is closed. The recalls encompass all model and my vehicles addressed by the investigation. However, the closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist in other model or my vehicles outside of the recall scope. The agency reserves the right to take further action if warranted by the circumstances.

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.