Toyota Yaris 2005

• Recall R/2015/096 [UK]: Passenger side airbag may fail to deploy correctly
  The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.
  recall the vehicles that are likely to be affected to replace the airbag.

  Show Content

• Recall R/2015/095 [UK]: Driver side airbag may rupture
  Subject vehicles are fitted with driver's air bag assemblies with single stage inflators. There is an increases potential for moisture ingress which could make the inflator more susceptible to rupture during deployment. Fragments may injure occupants.
  recall the vehicles that are likely to be affected to replace the airbag.

  Show Content

• Recall R/2019/442 [UK]: The vehicles may be equipped with front passenger airbag inflators not appropriate for the vehicles
  Vehicles may be equipped with front passenger airbag inflators not appropriate for the vehicles
  inspect and replace the affected parts if necessary

  Show Content

• Recall R/2007/073 [UK]: Seating headrests may detach & airbag may not deploy sufficiently in an impact
  It has been identified that the following seat defects may occur a front and rear seats - the locking performance of the headrest may be insufficient during an impact and may cause ejection of the headrest from the seat back. B front seats only- the reliability of the side airbag deployment on the front seats may be insufficient during an impact and may not offer the protection intended.
  recalled vehicles will have the following remedial actions performed:-a) the rear seat headrest guide springs and buttons will be replaced.B) the front seat headrest supports will be replaced. C) the front seat back pads and covers will be replaced.

  Show Content

• Recall R/2014/049 [UK]: Steering column may become unsecured
  The steering column mounting bracket may not be of sufficient strength if the steering is repeatedly and forcibly turned on full lock. This over a prolonged period can result in the failure of the bracket and ultimate detachment of the steering column.
  recall all affected vehicles and replace the steering column mounting bracket.

  Show Content

• Recall R/2009/013 [UK]: Fire may occur
  It has been identified that the possibility exists that the sound insulator beneath the front seatbelt pretensioner may become damaged by the high temperature gas generated when the device is activated during a collision. In the worst case should the insulator ignite a post-collision fire may ensue.
  recalled vehicles will have the sound insulator removed from beneath the centre body pillars.

  Show Content

• Recall R/2014/049 [UK]: Steering column may become unsecured
  The steering column mounting bracket may not be of sufficient strength if the steering is repeatedly and forcibly turned on full lock. This over a prolonged period can result in the failure of the bracket and ultimate detachment of the steering column.
  recall all affected vehicles and replace the steering column mounting bracket.

  Show Content

• Recall R/2015/095 [UK]: Driver side airbag may rupture
  Subject vehicles are fitted with driver's air bag assemblies with single stage inflators. There is an increases potential for moisture ingress which could make the inflator more susceptible to rupture during deployment. Fragments may injure occupants.
  recall the vehicles that are likely to be affected to replace the airbag.

  Show Content

• Recall R/2010/010 [UK]: Accelerator pedal may fail to return to idle
  It has been identified that on affected vehicles condensation resulting from cold-weather use of the heater or other causes may form on the worn surface of a component within the throttle pedal assembly known as the friction device. If this occurs there is a possibility that in the worst case the accelerator pedal may return slowly or does not return to the engine idle position.
  recalled vehicles will have a precision-cut steel reinforcing bar fitted into the accelerator pedal assembly which will create a space in order to reduce the surface tension between the friction device and a component referred to as the pedal arm. The subject bar also strengthens the reaction force of the spring that returns the accelerator pedal to it's non-pressed position.

  Show Content

• Recall R/2014/049 [UK]: Steering column may become unsecured
  The steering column mounting bracket may not be of sufficient strength if the steering is repeatedly and forcibly turned on full lock. This over a prolonged period can result in the failure of the bracket and ultimate detachment of the steering column.
  recall all affected vehicles and replace the steering column mounting bracket.

  Show Content

• Recall R/2014/050 [UK]: Seat rail mechanism could fail
  The drivers and front passengers seat forward/rearward adjustment mechanism locking spring could fail under repeated operation of the mechanism. The seat may not lock into the adjusted position. If the vehicle is operated with a broken seat rail spring the seat could move in the event of a crash
  recall all affected vehicles and replace the spring.

  Show Content

• Recall R/2015/206 [UK]: Risk of fire
  Affected vehicles are equipped with a driver?S side power window master switch (pwms) containing sliding electrical contact modules. These modules may not have been incorrectly coated during the manufacturing process. This may cause a short circuit which could cause the switch to overheat and melt
  inspect switch and apply coating. If switch indicates signs of malfunction it should be replaced.

  Show Content

• Recall 2021723 [Canada]: Accessories
  Issue: this recall is for certain block heater kits installed on certain vehicles or sold as accessories at toyota or lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: this recall only affects the following block heater/cord part numbers: C014003034 pk5a408j09 pU14000904 C014003151 pk5a408j13 pU14000905 C014000885 pk5a489j11 pU14000907 C014000888 pk5a489j22 pU14000909 C014000907 pk5a410h00 pU14000911 C014100904 pU14000900 pU14000913 C014100907 pU14000901 pU14003571 C014100911 pU14000902 pk5a408j05 pU14000903 safety risk: engine block heater wiring that overheats or melts could create the risk of a fire. Corrective actions: toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.