ITB11-005c
Service Bulletin Details
Public Details for: ITB11-005c
Wheel balancing service information this bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
- 2018 - 2017 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 -
Models from 2018
2018 INFINITI Q50 |
2018 INFINITI Q60 |
2018 INFINITI Q70 |
2018 INFINITI Q70 HYBRID |
2018 INFINITI QX30 |
2018 INFINITI QX60 |
Models from 2017
Models from 2016
Models from 2015
Models from 2014
Models from 2013
Models from 2012
Models from 2011
Classification: Reference: Date: WT10-006c ITB11-005c September 25, 2017 WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin. APPLIED VEHICLES: All 2011 – 2018 Infiniti SERVICE INFORMATION To increase tire/wheel assembly balancing accuracy, proper steps should be followed: Make sure to use the correct size wheel centering collet (do not use a cone). Make sure to use a flange plate and stud set to secure the tire/wheel assembly on the balancer (do not use a cup). NOTE: For Hunter balancing equipment – specific centering and mounting tools (collets and flange plates) for Applied Vehicles are available – see page 5. Perform proper wheel mounting and centering checks. Refer to the information in this bulletin for details on the above points. Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this applies to your vehicle. 1/5 Select the correct size road wheel centering collet. Do not use a cone (see Figure 1). OK Cone Collet Figure 1 For proper centering, the road wheel-to-collet contact area should be at the point shown in Figure 2. Part Numbers for Hunter collets that fit Applied Vehicles are listed on page 5. For non-Hunter equipment, select a size and shape collet that will contact the road wheel at the point shown in Figure 2. Cutaway of road wheel Wheel hub bore Road wheel-to-collet contact area (Collet should contact road wheel at this point.) (Center hole / opening of wheel) Figure 2 2/5 ITB11-005c Use a flange plate and stud set to secure the tire/wheel assembly on the balancer. Do not use a cup (see Figure 3). Part Number for Hunter flange plate and stud set that fits Applied Vehicles is listed on page 5. OK Cup Flange plate and studs Figure 3 NOTE: Using a flange plate and stud set will improve wheel centering, which improves balance accuracy, and helps protect the wheel from damage (marks and nicks). 3/5 ITB11-005c Properly mount the tire/wheel assembly to the wheel balancer (see Figures 4 and 5). Hunter equipment is shown, other equipment is similar. Cutaway of road wheel Stud Wing nut Collet Balancer shaft Flange plate Figure 4 Road wheel mounted flush Stud-to-road wheel contact Taper of the road wheel and taper of the collet are a close match. Figure 5 4/5 ITB11-005c Wheel Centering Quick Check 1. Run the tire/wheel assembly on the wheel balancer in the “non-round-off” mode and record the imbalance measurements. Mark the location where the weight(s) are requested. 2. Loosen the wing nut while keeping the tire/wheel assembly from turning on the balancer shaft. 3. Rotate the tire/wheel assembly 180 degrees on the balancer shaft, and then secure it with the wing nut. 4. Run the tire/wheel assembly again. The imbalance values should be within ¼ ounce (7 grams) of the values in Step 1. The weight(s) should be located within 2-3 inches (50-75 mm) of the locations in Step 1. Hunter Collet and Flange Plate Part Numbers for Applied Vehicles: HUNTER COLLET PART NUMBERS HUNTER FLANGE PLATE AND STUD SET PART NUMBER Mid Size Full Size 192-157-2 192-160-2 20-1839-1 20-1839-1 192-157-2 Mid Size 192-160-2 Full Size Figure 6 5/5 ITB11-005c