Altec Aerial Device 2020

Vehicle Details: Recalls, Service Bulletins

Below you will find all available information on the 2020 ALTEC Aerial Device.

ManufacturerKnown WMI(s)Fuel Type
ALTEC
ALTEC VIN Decoder

Use the box here to look up VINs from ALTEC as well as other manufacturers

#

Sub-models: - Aerial Device Jems Hybrid -

Frequently Asked Questions
  • Are there recalls for the 2020 ALTEC Aerial Device?
     - There are 23 recall(s) for the 2020 ALTEC Aerial Device, additional information is below.
NHTSA Mandated Recalls

  • Recall 253020 [USA]: A short circuit increases the risk of a fire.

  • Recall 237435 [USA]: An outlet without gfci protection may fail to shut off electrical power when a ground-fault occurs, increasing the risk of injury or fire.

  • Recall 237114 [USA]: An active braking system that fails to activate as intended increases the risk of a crash.

  • Recall 234432 [USA]: A missing weld on the rear pole rack can lead to a crack that could cause the pole and rack to drop in height, increasing the risk of an injury.

  • Recall 234746 [USA]: Outriggers that are not set when loads are being lifted by the jib winch may cause the unit to tip, increasing the risk of injury.

  • Recall 203894 [USA]: A cracked weld may allow the auger bracket to detach from the boom, increasing the risk of injury.

  • Recall 203951 [USA]: A blown fuse can cause an engine stall, increasing the risk of a crash.

  • Recall 230444 [USA]: Elevated levels of carbon monoxide gas may not be detected, increasing the risk of injury.

  • Recall 183457 [USA]: Unsecured fuel lines may become damaged and leak fuel, increasing the risk of a fire.

  • Recall 231240 [USA]: Shear plate failure can result in the separation of the subbase and truck frame, increasing the risk of injury.

  • Recall 208727 [USA]: Broken bolts can cause separation of the pedestal and turntable, increasing the risk of injury.

  • Recall 200937 [USA]: Broken bolts can cause the pedestal to separate from the turntable, increasing the risk of injury.

  • Recall 209652 [USA]: The operator could overextend the boom while using the material handling jib, causing the aerial device to tip over and increasing the risk of injury.

  • Recall 204944 [USA]: Broken bolts can cause the pedestal to separate from the turntable, increasing the risk of injury.

  • Recall 209018 [USA]: Overloaded bolts can fail, causing the pedestal to separate and increasing the risk of injury or death.

  • Recall 188407 [USA]: Unintended movement of the lower and upper booms increases the risk of injury.

  • Recall 155146 [USA]: The operator may not have access to the rated capacity information while they are operating the equipment in combined use, increasing the risk of an injury.

  • Recall 159396 [USA]: The valve not having a plug could result in unintended boom movement, increasing the risk of an injury.

  • Recall 147175 [USA]: Unintended boom movement may result in potential injury and or property damage.

  • Recall 150005 [USA]: If the fasteners break, the pedestal may separate from the turntable, increasing the risk of injury or death.

  • Recall 179815 [USA]: Oil absorbed by the exhaust heat shield thermal blanket has an increased risk of a fire from being exposed to hot engine components.

  • Recall 146984 [USA]: If the tow hitch is overloaded, the hitch may fail, increasing the risk of a crash.

  • Recall 180082 [USA]: If the fasteners break, the pedestal may separate from turntable, increasing the risk of injury or death.

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Recalls are also available on the Complaints page
Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • SIL 3123 - EQUIPMENT: Altec has learned that section 9 of the maintenance and parts manual for certain ac45e cranes built from september 2020 to november 2023 contains an incorrect torque value of 250 foot-pounds (339 na??M) for the rotation gearbox mounting cap
  • SIL 3065 - EQUIPMENT: Altec has learned that the pressure plates in the reel motor were not manufactured to specification, causing the plates to stick together. This can cause the reel park brake to not fully release, or cause the reel motor to lock up on certai
  • SIL 3099 - SUSPENSION: Altec has learned that on certain altec units equipped with air suspension built from april 2020 to june 2023, some operators may be dumping the chassis airbags before deploying the outriggers. This can cause the airbags to become damaged.
  • SIL 3110 - EQUIPMENT: Altec learned that a connection in the upper controls joystick in certain oem controls on at238p aerial devices built from november 2020 to august 2022 can fail due to wire movement during use and issued sil-845 to re-manufacture controller
  • SIL 3066 - ELECTRICAL SYSTEM: Altec has learned that operators might be using the crane and unit simultaneously on certain altec units equipped with venturo, liftmoore, and autocrane service cranes built from march 2009 to august 2022. These units were designed for sing
  • CSR 3109 - ENGINE AND ENGINE COOLING: Altec industries, inc. Has received notification from ford motor company that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. Certain 2020 to 2022
  • SIL 3054 - ELECTRICAL SYSTEM: Altec has learned that certain units built with a jobsite energy management system (jems) s/se/le from october 2020 to may 17, 2023, may fail to charge or operate properly, particularly when the battery is cold. Altec has developed a firmwa
  • CSR 3093 - ELECTRICAL SYSTEM: Altec industries, inc. Has received notification from navistar, inc. That a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. Navistar has decided tha
  • SIL 3082 - EQUIPMENT: Altec has learned that section 8 of the maintenance manual for certain altec ls60 aerial devices built from november 2017 to january 2023 contains an incorrect torque value of 325 foot-pounds for the rotation gearbox mounting cap screws. Al
  • SIL 3068 - EQUIPMENT: Altec has learned that certain digger derricks and aerial devices of various models built from january 2010 to january 2023 may contain access steps with a handrail and side plate that come together in a small space causing a potential pinc
  • CSR-3092 - VISIBILITY: Altec industries, inc. Has received notification from daimler truck north america llc (dtna), on behalf of its freightliner truck division, that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you
  • CSR 3083 - STEERING: Altec industries, inc. Has received notification from daimler truck north america that a condition exists relating to motor vehicle safety, compliance, or emissions in certain 2019 through 2021 model year freightliner 108sd, 114sd, 122sd, b
  • SIL 3021 - EQUIPMENT: The rear out and down outriggers on certain ls60 aerial devices built from july 2018 to april 2022 might contain a dual bonded hose with an externally attached electrical cable in the horizontal leg to operate the hydraulic cylinder and pro
  • CSR3063 - ELECTRICAL SYSTEM: Altec industries, inc. Has received notification from warn industries, inc. That a bumper winch supplied on certain altec units could contain a defect related to motor vehicle safety. Certain altec units built from december 2020 to septembe
  • 074900856 - ELECTRICAL SYSTEM: Altec used telematics data to identify jems in the field with batteries approaching critical discharge. After the min cell voltage becomes less than 3000mv the battery is no longer rechargeable in the field. To avoid costly battery replacem
  • SIL 3037 - EQUIPMENT: Altec has learned that the stability test form in the maintenance manuals for ls49 aerial devices built from july 2019 to july 2022 contains incorrect test weight information. This information has been corrected in the currently published m
  • CSR 3043 - SERVICE BRAKES, HYDRAULIC: Altec industries, inc. Has received notification from fiat chrysler automobiles that a condition exists relating to motor vehicle safety, compliance, or emissions in vehicles that are equipped with altec equipment. Certain 2019 and 2020 mod
  • SIL 3035 - FUEL SYSTEM, GASOLINE: Owners of certain at series and ta40/45 series aerial devices built on dodge ram 4500/5500 chassis from 2016 to 2022 received altec product notice csn 855 in may of 2022 calling for the inspection of fuel line securement. We have identified
  • CSR-525 - STRUCTURE: Altec industries, inc. Has received notification from ford motor company that a condition exists. This condition relates to the operation or customer satisfaction of the unit when equipped with an altec aerial device or equipment. Ford has
  • SIL-859 - EQUIPMENT: Altec has learned that on ah75/85/100, ah75a/85a/100a, and hl125 aerial devices built from november 2003 to january 2021, there is potential for the jib rotational positioning pin to disengage when the platform is tilted down 90 degrees or
  • CSR-3032 - EQUIPMENT: Altec industries, inc. Has received notification from general motors (gm) that for certain 2019 to 2022 chevrolet silverado 4500hd, 5500hd, and 6500hd vehicles the power take-off (pto) will kick out and/or disengages intermittently. This co
  • PA713 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL: Product advisory posted on our web site to inform owners, user, & operators that the new ansi a92.2-2021 standard has taken effect and they must review. The standard has changed some of the responsibilities of the parties who use or operat
  • SIL-857 - STRUCTURE: Certain 2020 through 2021 model year f-550 vehicles equipped with a payload plus upgrade package and a 19,500 lbs. Gvwr were ordered from ford with a frame rail specification that does not meet the original equipment manufacturer (oem) spec
  • CSR-541 - UNKNOWN OR OTHER: Altec industries, inc. Has received notification from ford motor company that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. The windshield wiper
  • SIL 856 - EQUIPMENT: Altec has learned of the potential for washers on the outer race rotation bearing cap screws to overlap the adjacent weld on at238p and at335 aerial devices built from october 2019 to november 2021. While there have been no reports of unit
  • CSR 540 - POWER TRAIN: Altec industries, inc. Has received notification from an original equipment manufacturer (oem) that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment
  • SIL 850 - ELECTRICAL SYSTEM: The body compartment wiring on certain altec aerial devices, digger derricks, and body-only units built from 2014 to 2021 contains an in-line fuse located close to the lighting in the compartment, while other units are fused upstream, close
  • SIL 852 - EQUIPMENT: Altec has learned that the electrohydraulic outrigger/tools control valve on aa755l and a-series aerial devices and dlb, dmb, and d2/3/4000b series digger derricks could have the potential to produce a very small amount of flow into the low
  • SIL 845 - UNKNOWN OR OTHER: Altec has learned that a connection in the upper controls joystick on at238p aerial devices built from november 2020 to september 2021 can fail due to wire movement during use. If this happens with the boom elevated, the operator in the pla
  • SIL 848 - EQUIPMENT: Altec has learned that the engine on certain at35/37/40g and at37/41/48 me/pe aerial devices built from august 2020 to august 2021 on ford f-450/f550/f-600 gas engine chassis equipped with a jems s/se hybrid system could not enter idle miti
  • CSR 537 - STEERING: Altec industries, inc. Has received notification from ford motor company that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. Ford motor company
  • CSR 536 - EQUIPMENT: Altec industries, inc. Has received notification from fiat chrysler automobiles (fca) that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. Fca us
  • CSR 531 - ELECTRICAL SYSTEM: Altec industries, inc. Has received notification from navistar that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. On certain trucks equipped
  • CSR 532 - POWER TRAIN: Altec industries, inc. Has received notification from navistar that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. On certain trucks equipped
  • CSR 528 - FUEL SYSTEM, DIESEL: Altec industries, inc. Has received notification from an original equipment manufacturer (oem) that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment
  • SIL 844 - EQUIPMENT: Altec has learned that there could be loose, missing, or incorrectly installed mounting fasteners on the electric power take-off (epto) on certain aerial devices built from 2015 to 2020 and equipped with a jems 18e20 hybrid system. This can
  • CSR 529 - EQUIPMENT: Altec industries, inc. Has received notification from an original equipment manufacturer (oem) that a condition exists. This condition relates to the operation or customer satisfaction of the unit when equipped with an altec aerial device o
  • No comms 2021-12 - UNKNOWN OR OTHER: There are no manufacturer communications in accordance with 49 cfr 579.5 to report for december 2021 for altec industries, inc.
  • SIL 839 - UNKNOWN OR OTHER: Some customers have reported the loss of functionality of the altec unit or the ez trac system on certain 2016-2021 ford f750 chassis with ez trac hydraulic all-wheel drive installed. The investigation has shown that improper wiring could h
  • SIL 830 - EQUIPMENT: Some customers have reported hose carrier failure and/or cover damage occurring during the operation of ls60 aerial devices built from january 2017 to may 2020. Altec has developed an improved design of the hose carrier tray and cover syste
  • PUN 2021D - EQUIPMENT:OTHER:LABELS: Altec has learned that the labeling describing the proper jump starting procedure for certain vehicles equipped with a jobsite energy management system (jems) 2, 4, 6, or 12 built by altec from 2015 to 2021 has sometimes been overlooked. Fa
  • CSR 525 - STRUCTURE: Altec is notifying our customers with certain aerial devices that ford has issued a customer satisfaction campaign for certain 2017 through 2020 model year f550 vehicles equipped with a payload plus upgrade package. Every affected unit is e
  • SIL 831 - EQUIPMENT: Altec has discovered that certain at200a aerial devices built from june 2020 to january 2021 could have square inside corners on a mounting frame side plate. The square corners can cause excessive stress levels in the side plate. Over time
  • CSR 521 - WHEELS: Fiat chrysler automobiles (fca) us has decided that a defect that relates to motor vehicle safety exists on certain 2012 through 2020 model year (d2) ram 3500 pickup, (dd) ram 3500 cab chassis, and (dp) ram 4500/5500 cab chassis vehicles.
  • SIL 822 - EQUIPMENT: Altec has learned that certain at237 and at248f aerial devices built from april 2017 through march 2020 might have insufficient slack in the hydraulic hoses at the riser between the lower and upper booms, which could lead to hoses rubbing o
  • SIL 819 - EQUIPMENT: Certain 2017-2020 ford f350/f450/f550 chassis with timbren springs installed near the chassis front coil springs can loosen over time and could eventually become disconnected. Altec requires the timbren springs to be inspected no later tha
  • SIL 810 - EQUIPMENT: Chafing can occur on hoses at the rear of the turntable on certain ls60 aerial devices built from february 2018 to february 2021. Altec requires the hose routing to be inspected on the affected units no later than the next periodic maintena
  • SIL 798 - EQUIPMENT:MECHANICAL:INTEGRATED JACK/LEVELER/STABILIZER:CRITICAL FASTENERS: On certain at37/41/48 m/me/p/pe/s/se aerial devices built from june of 2015 to march of 2020 altec requires the platform leveling bracket assembly to be inspected as described in the inspection procedure. If the inspection discovers any mi
  • PUN 2021B - ELECTRICAL SYSTEM: The system firmware on the altec jobsite energy management system (jems) s/se/le built from 2020 to 2021 is being updated to improve the performance of the telematics system. This update does not affect the operation of the jems system. Thi
  • SIL 806 - EQUIPMENT: Altec has learned that certain rear-mounted lr7 units built from may 2019 to april 2021 have reports of the platform ribs separating from the platform shell near the bottom of the platform. The separation can be caused by excessive bouncing
  • SIL 805 - EQUIPMENT ADAPTIVE/MOBILITY: Altec has learned that certain ts20-4p units built from 2019 to 2021 have fairlead rollers that do not consistently rotate freely. This operation can cause damage to the ropes. Altec requires that the levelwind fairleads be replaced within
  • SIL 801 - EQUIPMENT: Altec has learned that the fender rubber on certain units built from july 2020 to october 2020 can become detached from the wheel well fender cutout of the utility body. Altec recommends that all fender rubber be inspected using the inspec
  • SIL 797 - EQUIPMENT: Certain lr7 aerial devices sold between september 2020 and november 2020 might have a trailer plug wiring configuration that was specified in the purchase order to supply a constant 12+ volts to pin 6. If you intend to pull a trailer that i
  • SIL 796 - EQUIPMENT: Altec has discovered that cracks might have formed in the yoke of the platform assembly on some ac40 cranes equipped with a personnel platform built between february 2014 and november 2020. Although the cracks do not compromise the structur
  • CSR 514 - VEHICLE SPEED CONTROL: Altec industries, inc. Has received notification from an original equipment manufacturer (oem) that certain 2020 ram chassis with adaptive cruise control have a condition relating to motor vehicle operation or customer satisfaction.
  • CRS 512 - POWER TRAIN: Cummins has launched a customer satisfaction campaign for certain cummins b6.7 diesel engines produced between august 26, 2020 and october 5, 2020, that may have been installed. Some of the affected vehicles may contain engine valve spring
  • CSR 511 - FUEL SYSTEM, DIESEL: Certain b6.7 diesel engines manufactured between december 16, 2015 and march 24, 2020 and equipped with fuel module option fs90301 or fs90453 were either delivered with a heater plug in place of the fuel heater, or your vehicle is subject t
  • CSR 509 - ENGINE (PWS): Ford motor company has decided that a defect which relates to motor vehicle safety exists in certain 2021 model year econoline ford e-350 and e-450 equipped with a 7.3l engine and a factory engine cover built between may 11, 2019 and novemb
  • CSR 510 - FUEL SYSTEM, DIESEL: Cummins inc. Has decided that a defect that relates to motor vehicle safety exists in certain b6.7 diesel engines manufactured between december 16, 2015, and march 24, 2020, and equipped with fuel module option fs90301 or fs90453. Cummins
  • CSR 508 - WHEELS: Daimler trucks north america llc (dtna), on behalf of its freightliner trucks division and wholly-owned subsidiary, western star truck sales inc., has decided that a defect which relates to motor vehicle safety exists on specific model year
  • CSR 506 - ELECTRICAL SYSTEM: Altec has been notified of a recall campaign by daimler trucks north america, llc (dtna). Dtna, on behalf of its freightliner trucks division, has decided that a defect that relates to motor vehicle safety exists on specific model year 201
  • SIL 764 - STRUCTURE: Altec has discovered that the protective fabric hose sock in the upper boom hose carrier on the affected units can become unsecured and slip out of place. This can expose the fiber optic lines to damage, resulting in intermittent operation
  • CSR 504 - ELECTRICAL SYSTEM: Pto disabled due to engine shutdown altec has been notified of a customer satisfaction campaign by general motors. It is possible that certain 2019⿿2020 model year chevrolet silverado 4500hd/5500hd/6500hd vehicles equipped with an ae
  • SIL 753 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Altec discovered that the torque requirement for the inner race rotation bearing bolts for the ls60 was incorrect on one of the pages in the maintenance manual. The correct torque requirement is 300 foot-pounds (407 n.M). In the two manua
  • PUN 2020B - EQUIPMENT: Product update notice 2020b reminded customers that they may be unable to store necessary equipment in the body of the cutaway van without exceeding the rear axle capacity. For customers who are not satisfied with the remaining capacity of

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.