Mercedes-benz Gle 2016

• Recall R/2016/139 [UK]: Engine may stall/stop unexpectedly
  The engine may stop when braking from lower speeds right before the vehicle comes to a standstill. The concern might be interpreted by the driver as a planned engine stop as part of the automatic stop/start system and the engine will not restart after release of the brake pedal. Depending on traffic situation there could be an increased risk of collision.
  recall the vehicles that are likely to be affected and update the software.

• Recall R/2017/148 [UK]: Steering power assist may deactivate
  The connector on the electric power steering control unit may not be properly sealed against water entry. If water enters the control unit the power steering assistance can be lost. The steering assistance not working could increase the risk of collision.
  recall the vehicles that are likely to be affected and replace the plug housing of the electric power steering.

• Recall R/2018/206 [UK]: Oil foam may develop in the active curve system oil reservoir
  It has been determined that on model series ml/gle gl/gls (166) & gle coupe (292) with active curve system (acs) oil foam may develop in the systems oil reservoir under dynamic operating conditions and at an oil level below the minimum level and escape via the ventilation bores in the cap of the reservoir. Depending on the orientation of the two ventilation bores the escaping oil could spray onto hot component parts of the exhaust system. In this case risk of fire cannot be ruled out.
  on affected vehicles replace the oil dipstick of the reservoir for the active curve system.

• Recall R/2019/307 [UK]: Software update required to improve emissions
  Improve the vehicle emissions via software updates
  update the diesel engine control unit software and add a supplementary booklet for the operator's manual. Check and replace n0x sensor if necessary.

• Recall R/2019/256 [UK]: To achieve an improvement in the emissions via software updates
  Improve the vehicle emissions via software updates.
  update the diesel engine control unit software and add a supplementary booklet for the operator's manual

• Recall R/2019/304 [UK]: Software update required to improve emissions
  Improve the vehicle emissions via software updates.
  update the diesel engine control unit software and add a supplementary booklet for the operator's manual. Check and replace nox sensor if necessary.

• Recall R/2018/266 [UK]: To improve emissions of the affected vehicles.certain calibrations of functionalities must be changed in the engine management
  Improve the vehicle emissions via software updates.
  update the diesel engine control unit software and add a supplementary booklet for the operator's manual

• Recall R/2017/267 [UK]: Engine ecu has not been corrctly programmed
  Due to an error in the engine control unit software the engine may shut down when braking from slow speeds such as pulling up at traffic lights. This may also affect the vehicles eco start system. It will still be possible to manually restart the vehicle.
  on affected vehicles update engine and transmission control units.

• Recall R/2021/120 [UK]: The behaviour of the emergency call system might not meet specifications
  The behaviour of the emergency call system might not meet specifications.
  update the software of the communication module for the emergency call system.

• Recall R/2021/129 [UK]: The emergency call system might not meet specifications
  The behaviour of the emergency call system might not meet specifications.
  update the software of the communication module for the emergency call system.

• Recall R/2021/130 [UK]: The behaviour of the emergency call system might not meet specifications
  The behaviour of the emergency call system might not meet specifications.
  update the software of the communication module for the emergency call system.

• Recall R/2020/243 [UK]: Engine control unit software to be updated
  Improve the vehicle emissions via software updates.
  update the relevant control unit?S software and if necessary replace the nox sensors.

• Recall R/2019/256 [UK]: To achieve an improvement in the emissions via software updates
  Improve the vehicle emissions via software updates.
  update the diesel engine control unit software and add a supplementary booklet for the operator's manual

• Recall R/2019/304 [UK]: Software update required to improve emissions
  Improve the vehicle emissions via software updates.
  update the diesel engine control unit software and add a supplementary booklet for the operator's manual. Check and replace nox sensor if necessary.

• Recall R/2021/274 [UK]: Vehicles with a panoramic sunroof the polycarbonate panel may not have been bonded correctly during a prior service repair
  The polycarbonate panel located between the windshield and the panoramic sunroof may not have been bonded correctly during a prior service repair.
  remove the bonded panel and install a new polycarbonate panel if required.

• Recall R/2017/267 [UK]: Engine ecu has not been corrctly programmed
  Due to an error in the engine control unit software the engine may shut down when braking from slow speeds such as pulling up at traffic lights. This may also affect the vehicles eco start system. It will still be possible to manually restart the vehicle.
  on affected vehicles update engine and transmission control units.

• Recall R/2021/110 [UK]: The behaviour of the emergency call system might not meet specifications
  The behaviour of the emergency call system might not meet specifications.
  update the software of the communication module for the emergency call system.

• Recall R/2021/133 [UK]: The emergency call system might not meet specifications
  The behaviour of the emergency call system might not meet specifications.
  update the software of the communication module for the emergency call system.

• Recall R/2021/134 [UK]: The behaviour of the emergency call system might not meet specifications
  The behaviour of the emergency call system might not meet specifications.
  update the software of the communication module for the emergency call system.

• Recall R/2021/082 [UK]: The communication module may be deactivated
  The communication module may be deactivated
  carry out a check of the configuration of the communication module on affected vehicles and if necessary activate the communication module.

• Recall R/2021/108 [UK]: The behaviour of the emergency call system might not meet specifications
  The behaviour of the emergency call system might not meet specifications.
  update the software of the communication module for the emergency call system.

• Recall R/2021/133 [UK]: The emergency call system might not meet specifications
  The behaviour of the emergency call system might not meet specifications.
  update the software of the communication module for the emergency call system.

• Recall R/2021/134 [UK]: The behaviour of the emergency call system might not meet specifications
  The behaviour of the emergency call system might not meet specifications.
  update the software of the communication module for the emergency call system.

• Recall 2018724 [Canada]: Steering
  On certain vehicles originally sold or currently registered in areas of heavy road salt usage during winter months (quebec, new brunswick, nova scotia, prince edward island, and newfoundland & labrador), the bolts that attach the electric power steering assist motor to the steering gear housing may corrode and break. This could cause a loss of power steering assist. The resulting increase in steering effort could create the risk of a crash causing injury and/or damage to property. Correction: dealers will replace the mounting bolts and apply a corrosion protection coating to the gear housing and bolts. If the bolts bolt cannot be removed, a replacement steering gear will be installed.

• Recall 2018217 [Canada]: Engine
  On certain vehicles equipped with the active curve system (acs), the oil in the acs’s reservoir could start foaming under certain dynamic driving situations in combination with an oil level below minimum. The oil foam could leak out of the oil reservoir through the vent holes in the sealing cap and spray onto hot surface components of the exhaust system. This could increase the risk of fire causing injury and/or damage to property. Correction: dealers will inspect the acs reservoir for proper oil level and replace the sealing cap with an updated part.

• Recall 2017501 [Canada]: Structure
  Certain vehicles may fail to comply with the requirements of canada motor vehicle safety standard (cmvss) 208 - occupant protection in frontal impacts and cmvss 115 - vehicle identification number (vin). Excess bulkhead insulation material may have been used during manufacturing, and as a result, could extend into the lower area of the windshield. This excess insulation could cover the vin label, and potentially affect bonding of the windshield. If the windshield bonding is affected on the passenger side, in the event of a crash (where passenger frontal airbag deployment is warranted), the airbag may not deploy as designed, which would fail to meet the requirements of the standard, and increase the risk of injury in a crash. Correction: dealers will inspect the bulkhead insulation for excess material and remove it as necessary. In the event of compromised windshield bonding, the bonding will be reworked.

• Recall 2017395 [Canada]: Engine
  On certain vehicles, the engine control unit may be out of specification. This could result in the engine shutting down when applying the brakes just before stopping the vehicle, and/or with a high engine load combined with an insufficient accelerator pedal actuation following an eco start. Depending on traffic conditions, an unintentional engine shut-down could increase the risk of a crash causing injury and/or damage to property. Correction: dealers will update the engine and transmission control unit software.

• Recall 2017207 [Canada]: Steering
  On certain vehicles, the electric power steering connector may not be properly sealed against water entry. This could allow moisture to enter the power steering control unit which could interrupt the signal and cause the electric steering assist to deactivate. A loss of power steering assist could unexpectedly increase steering effort which would increase the risk of a crash causing injury and/or damage to property. Correction dealers will replace the connector and, if necessary, replace the steering rack.

• Recall 2017060 [Canada]: Structure
  Certain vehicles may fail to comply with the requirements of canada motor vehicle safety standards (cmvss) 208 - occupant protection in frontal impacts and cmvss 212 - windshield mounting. The bonding of the windshield might not meet specifications of the 212 standard. This could result in the possibility of the windshield separating in the event of a crash, and in the case of a head-on collision warranting deployment of the passenger frontal airbag, the windshield might not be able to support the airbag as intended, affecting compliance to the 208 standard and increasing the risk of injury to the front passenger seat occupant. Correction: dealers will replace the windshield.

• Recall 2017059 [Canada]: Steering
  On certain vehicles, the connections between the upper control arms and the axle stubs may not have been tightened properly during assembly. This could affect steering and directional control of the vehicle, increasing the risk of a crash causing injury and/or property damage. Correction: dealers will check the bolt torque connections between the upper control arms and axle stubs and replace the upper control arms if necessary.

• Recall 2016618 [Canada]: Seats and restraints
  On certain vehicles, the calibration of the front passenger seat occupant classification system (ocs) may not detect a small statured seat occupant if the occupant is sitting on the edge of the seat and remains stationary for a long period of time. As a result, the passenger frontal airbag may not deploy in a crash, increasing the risk of injury. Correction: dealers will update the software of the occupant classification system.

• Recall 2016512 [Canada]: Engine
  On certain vehicles, the engine control unit software may be incorrect. This would result in reduced engine performance of 300kw (600nm) instead of the specified 320kw (700nm) listed within vehicle certification documents. Correction: dealers will replace the engine control unit.

• Recall 2016510 [Canada]: Lights and instruments
  Certain vehicles may not comply with the requirements of canada motor vehicle safety standard (cmvss) 108 - lighting system and retroreflective devices. The low-beam headlamps may not have been adjusted according to specification, which may deviate from the tolerance range required by the standard. This could reduce vehicle visibility, which could increase the risk of a crash causing injury and/or damage to property. Correction: dealers will check the setting of the headlamps and correct them as necessary.

• Recall 2016300 [Canada]: Engine
  On certain amg model vehicles, there could be an issue within the software of the engine control unit (ecu) which could cause an engine shut-down just before a vehicle stop. If this were to occur, the driver might mistakenly interpret the engine shut-down as a planned shut-down as part of the eco start/stop system. However, the engine will not restart automatically after releasing the brake pedal, and would needed to be restarted manually. Depending on traffic conditions and the driver’s reactions, an unintentional engine shut-down could increase the risk of a crash. Correction: dealers will update the ecu software.

• Recall 2021170 [Canada]: Structure
  Issue: on certain vehicles, the plastic panel located between the windshield and the panoramic sunroof may not have been attached correctly during a prior service repair. Over time, the panel could loosen and separate from the vehicle. Safety risk: a panel that detaches from a moving vehicle could create a road hazard for others and increase the risk of a crash. Corrective actions: mercedes-benz will notify owners by mail and instruct you to take your vehicle to a dealer to replace the front roof panel.

• Recall 2017501 [Canada]: Structure
  Certain vehicles may fail to comply with the requirements of canada motor vehicle safety standard (cmvss) 208 - occupant protection in frontal impacts and cmvss 115 - vehicle identification number (vin). Excess bulkhead insulation material may have been used during manufacturing, and as a result, could extend into the lower area of the windshield. This excess insulation could cover the vin label, and potentially affect bonding of the windshield. If the windshield bonding is affected on the passenger side, in the event of a crash (where passenger frontal airbag deployment is warranted), the airbag may not deploy as designed, which would fail to meet the requirements of the standard, and increase the risk of injury in a crash. Correction: dealers will inspect the bulkhead insulation for excess material and remove it as necessary. In the event of compromised windshield bonding, the bonding will be reworked.

• Recall 2017395 [Canada]: Engine
  On certain vehicles, the engine control unit may be out of specification. This could result in the engine shutting down when applying the brakes just before stopping the vehicle, and/or with a high engine load combined with an insufficient accelerator pedal actuation following an eco start. Depending on traffic conditions, an unintentional engine shut-down could increase the risk of a crash causing injury and/or damage to property. Correction: dealers will update the engine and transmission control unit software.

• Recall 2017207 [Canada]: Steering
  On certain vehicles, the electric power steering connector may not be properly sealed against water entry. This could allow moisture to enter the power steering control unit which could interrupt the signal and cause the electric steering assist to deactivate. A loss of power steering assist could unexpectedly increase steering effort which would increase the risk of a crash causing injury and/or damage to property. Correction dealers will replace the connector and, if necessary, replace the steering rack.

• Recall 2016618 [Canada]: Seats and restraints
  On certain vehicles, the calibration of the front passenger seat occupant classification system (ocs) may not detect a small statured seat occupant if the occupant is sitting on the edge of the seat and remains stationary for a long period of time. As a result, the passenger frontal airbag may not deploy in a crash, increasing the risk of injury. Correction: dealers will update the software of the occupant classification system.

• Recall 2016403 [Canada]: Seats and restraints
  On certain vehicles, if subjected to low temperatures of -20° c or colder, the rear head restraints may not remain locked in the upright position. In the event of a crash at low temperatures, this could increase the risk of injury to the seat occupant. Correction: dealers will replace the rear head restraints.

• Recall 2015506 [Canada]: Powertrain
  On certain vehicles, the rear drive shaft bolts may not have been tightened to specification and could loosen, which could, overtime, cause the drive shaft to separate from the transmission. This could cause a loss of motive power, increasing the risk of a crash causing injury and/or damage to property. Correction: dealers will inspect and tighten the bolts as necessary.

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

Common OBD Error codes specific to this vehicle.

• P0442 [1] Evaporative Emission Control System Leak Detected (small leak)
• P0456 [1] Evaporative Emissions System Small Leak Detected
• P1C9B [1] P1C9B
• P1000 [1] Manufacturer Controlled DTC
• P1002 [1] P1002
• B2105 [1] Throttle Position Input Out of Range Low
• P054A [1] Cold Start "B" Camshaft Position Timing Over-Advanced Bank 1
• P054C [1] Cold Start "B" Camshaft Position Timing Over-Advanced Bank 2
• P0628 [2] Fuel Pump "A" Control Circuit Low
• U0109 [2] Lost Communication With Fuel Pump Control Module

I purchased my 2016 mercedes benz gle 350 late september 2019. Since i have owned the vehicle i have had issues with water getting in through the lift gate. On saturday jan 4 this water entry through trunk caused my mercedes benz to stall while driving. Fortunately i was on a safe roadway with ample space between other drives and an accident did not occur. After towing it home i had the car diagnosed by my local mercedes benz specialist. The computer had the following stored diagnostic codes. P053f94 stored the fuel pressure during a cold start is implausible. There exists an unexpected instruction. P062800 current the output for the fuel pump has a short circuit to the ground. U010987 current and stored communication with the fuel pump module is faulty. The message is lost. These diagnostic codes led to technical service bulletin water entry through trunk reference number(s) li88.50-p-069683 version 1 date of issue: april 12, 2019 function group 88.50 trunk lid complaint trunk seal is loose, vehicle will not start, or check engine light
 cause possible improper fit of trunk seal or water entry to the fuel pump unit remedy please open a ptss case. Do not modify in anyway.

I purchased my 2016 mercedes benz gle 350 late september 2019. Since i have owned the vehicle i have had issues with water getting in through the lift gate. On saturday jan 4 this water entry through trunk caused my mercedes benz to stall while driving. Fortunately i was on a safe roadway with ample space between other drives and an accident did not occur. After towing it home i had the car diagnosed by my local mercedes benz specialist. The computer had the following stored diagnostic codes. P053f94 stored the fuel pressure during a cold start is implausible. There exists an unexpected instruction. P062800 current the output for the fuel pump has a short circuit to the ground. U010987 current and stored communication with the fuel pump module is faulty. The message is lost. These diagnostic codes led to technical service bulletin water entry through trunk reference number(s) li88.50-p-069683 version 1 date of issue: april 12, 2019 function group 88.50 trunk lid complaint trunk seal is loose, vehicle will not start, or check engine light
 cause possible improper fit of trunk seal or water entry to the fuel pump unit remedy please open a ptss case. Do not modify in anyway.

Defective jack - the car was stationary on the shoulder of an interstate in order to fix a flat tire. The jack prong was inserted as designed into the hole under the car and the car was raised to remove the tire. Upon raising, the prong deformed and resulted in the collapse of the car. The resulting deformity rendered the jack inoperative and almost resulted in severe injury. The consumer stated mercedes roadside assistance was not appropriately responsive while the stranded on the shoulder of the highway. *js

2016 mercedes benz gle. Consumer writes in regards to engine shutting off while driving. *ld the consumer stated the control module was replaced. *js

Tl* the contact owns a 2016 mercedes-benz gle. While driving various speeds, the headlights were very dim and it was difficult for the contact to see the road while driving. The vehicle was taken to mercedes-benz of hagerstown (1955 dual hwy, hagerstown, md 21740, (301) 733-2301) to be diagnosed, but no failure was found. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was 30,000. *tt*jb