Mercedes-benz E400 Hybrid 2013

• Recall 151054 [USA]: An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
  Mercedes-benz usa, llc. (mbusa) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (ecall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit: https://static.Nhtsa.Gov/odi/rcl/2019/rmisc-19v787-4620.Pdf
  mbusa has initiated an over the air (ota) remote update. Mbusa will also notify owners, and dealers will check software for a successful ota or update the communication module software as needed, free of charge. The recall began december 23, 2019. Owners may contact mbusa customer service at 1-800-367-6372. Mbusa's number for this recall is 2019120008.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 115663 [USA]: If the rubber seal falls into the engine compartment, it may contact parts of the exhaust system, increasing the risk of a fire.
  Mercedes-benz usa, llc. (mbusa) is recalling certain model year 2013-2015 e350 sedan, e350 4matic sedan, e350 4matic station wagon, e400 hybrid sedan, cls 550 cgi, and cls550 4matic, 2013-2014 e550 4matic sedan, 2013 e63 sedan, e63 station wagon and cls63, 2014-2015 cls63 4matic, e63 4matic sedan, e63 4matic sedan "s", and e63 4matic station wagon, 2015 cls400, 2015 e400 sedan, e400 4matic sedan and cls400 4matic and 2014 cls63 "s". The affected vehicles have a rubber seal at the back of the engine bay that may temporarily stick to the hood when it is opened and then may fall into the engine bay when the hood is closed.
  mbusa will notify owners, and dealers will attach four additional retaining clips to the rubber seal, free of charge. The recall began march 6, 2015. Owners may contact mbusa customer service at 1-201-573-5339. Mbusa's number for this recall is 2015020001.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Desiccated air bag inflator rupture investigation # EA21002

  From 2000 through 2017, takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("psan") propellant -- propellant 2004 and propellant 2004l. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 blomquist report at www.Nhtsa.Gov/sites/nhtsa.Gov/files/documents/expert_report-hrblomquist.Pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in us vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004l that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated psan inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All takata inflators produced with propellant 2004l contain desiccant, and none of these desiccated inflators using propellant 2004l are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated psan inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- takata (now known as tk global), the independent testing coalition, and exponent -- have been studying the long-term behavior of takata desiccated psan inflators using propellant 2004l (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004l is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004l.The office of defects investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated psan frontal inflators manufactured by takata. This investigation will require extensive information on takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated psan inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.Gov/recalls?Nhtsaid=ea21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede ea15-001, which remains open.
  

  Show Content

• Rear brake line failure investigation # DP20004

  On april 10, 2020, nhtsas office of defects investigation (odi) received a defect petition from mr. Surjit singh alleging premature corrosion of the rear brake lines in his 2013 mercedes-benz e350 sedan. The petitioner states that he was recently informed by a mercedes dealer service department that his car had "severely rusted brake lines that need[ed] to be replaced immediately at a cost of about $3300." he further stated that the dealer service advisor informed him that he had seen the issue on many cars like his. The petitioner requested ?That nhtsa launch an investigation into this serious issue of rusting brake lines on [his] 2013 mercedes e350.? The brake line corrosion reported by the petitioner did not result in brake line leakage or any compromise in brake system performance before it was detected in a dealer vehicle inspection. The petitioner submitted a complaint to nhtsa documenting his experience (nhtsa id 11319024).On april 24, 2020, odi opened defect petition dp20-004 to evaluate the petitioner?S request. Odi conducted a search for all consumer complaints and early warning reporting (ewr) data related to allegations of brake line corrosion or leakage in 2013 mercedes-benz e350 sedans and similarly equipped vehicles. The 2013 e350 is a fourth-generation mercedes-benz e-class vehicle (w212 platform), which was first sold in the united states in 2009 as a 2010 model. Mercedes-benz sold approximately 245 thousand model year 2010 through 2015 e-class sedan and wagon vehicles in the united states with the same brake line design as the petitioner?S vehicle.Odi?S search for complaints and ewr data in 2013 mercedes e350 vehicles found no additional records related to the alleged defect. Expanding the search to all w212 platform vehicles identified just one incident, a complaint alleging unspecified brake line corrosion and leakage in a 2011 mercedes-benz e550 (nhtsa id 10902081). The complaint did not allege that the brake line leakage resulted in reduced brake performance, crash, or injury. The resulting failure rate of 0.4 failures per hundred thousand vehicles is extremely low for a population that includes vehicles that have been in service for over ten years. After reviewing the available data, odi has not identified evidence of a defect trend in the subject e-class vehicles that would support opening a defect investigation into premature brake line corrosion failure. Nhtsa is authorized to issue an order requiring notification and remedy of a defect if the agency?S investigation shows a defect in design, construction, or performance of a motor vehicle that presents an unreasonable risk to safety. 49 u.S.C. ?? 30102(a)(9), 30118. Since the information before the agency is not indicative of a vehicle-based defect, it is unlikely that any investigation opened because of granting this petition would result in an order concerning the notification and remedy of a safety-related defect. Therefore, upon full consideration of the information presented in the petition and the potential risks to safety, the petition is denied. The denial of this petition does not foreclose the agency from taking further action if warranted or the potential for a future finding that a safety-related defect exists based upon additional information the agency may receive.A federal register notice further detailing nhtsa?S reasons for denial of the petition will be forthcoming.
  

  Show Content

My car was parked in our garage which is level. My son and i got into the car, and i attempted to put the car in reverse to leave. After several attempts, the car would not go into gear. With the car still parked in the garage and with the engine off, my son and i exited the car, and i went inside the house to get the keys to another car. About 10 minutes later when my son and i were in the other car (parked on the street) getting ready to leave, we saw my car, with no one in the car, exit the garage and go down my driveway and into the plants and rocks in my front yard.

Tl* the contact owns a 2013 mercedes-benz e400 hybrid. The contact stated that while driving approximately 70 mph, she depressed the brake pedal but the brakes did not respond. The contact continued to depress the brake pedal in order to come to a stop. The failure occurred five different times. The vehicle was towed to the dealer for diagnostic testing. The technician stated that the brake sensor would have to be replaced. The vehicle was not repaired. The approximate failure mileage was 120.

Common OBD-II Error Codes

• P0128 [1] Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)
• P0442 [1] Evaporative Emission Control System Leak Detected (small leak)
• P0456 [1] Evaporative Emissions System Small Leak Detected
• P0722 [1] Output Speed Sensor No Signal
• P0723 [1] Output Speed Sensor Intermittent
• P0729 [1] Gear 6 Incorrect Ratio
• P0730 [1] Incorrect Gear Ratio
• P0731 [1] Gear I Incorrect ratio
• P0732 [1] Gear 2 Incorrect ratio
• P0733 [1] Gear 3 Incorrect ratio
• P0734 [1] Gear 4 Incorrect ratio
• P0735 [1] Gear 5 Incorrect ratio
• P076F [1] Gear 7 Incorrect Ratio
• P0606 [1] PCM Processor Fault
• U1454 [1] U1454