Prevost X3-passenger-coach 2017
Vehicle Details: Investigations, Decoded VIN Details, Service Bulletins
PREVOST VIN Decoder
Use the box here to look up VINs from PREVOST as well as other manufacturers
Frequently Asked Questions
-
Where is the 2017 PREVOST X3-PASSENGER-COACH produced?
- The 2017 PREVOST X3-PASSENGER-COACH is produced in Ste-claire Quebec, Canada.
-
How much horsepower does the 2017 PREVOST X3-PASSENGER-COACH have?
- The 2017 PREVOST X3-PASSENGER-COACH has 435 horsepower.
NHTSA Mandated Recalls
Bulletins
Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.
- MI16-32 - ENGINE AND ENGINE COOLING: Improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
- IS-21072B - ELECTRICAL SYSTEM: Steering gateway. Revision b - pin 2 and 10 were inverted on connector a139
- MI22-12B - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: b - general update
- SP18-35J - ENGINE AND ENGINE COOLING: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency. Revision j - range of applicable vins updated.
- MI22-12A - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: a - erroneous secondary & accessory tanks location.
- MI22-12 - SERVICE BRAKES, AIR: Air tanks draining sequence
- IS-17151C - EXTERIOR LIGHTING: Halogen to led fog light replacement kit. Revision: c - advanced kits canceled
- SP18-35J - ENGINE AND ENGINE COOLING: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency. Revision j - range of applicable vins updated.
- IS-22902 - WHEELS: Tag axle hub flange - alternate cap screw
- IS21-072 - ELECTRICAL SYSTEM: Steering gateway, revision a : cancel watch dog removal from efd part of the instruction
- MI20-08C - EQUIPMENT: Storage and startup guidelines : part number updates
- IS21-901 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : X3 series envirocare - ions air sanitizer
- IS21-072A - ELECTRICAL SYSTEM: Steering gateway revision a cancel watch dog removal from efd part of the instruction
- IS20-925A - VISIBILITY: Central hvac merv filters installation
- IS22-040 - EQUIPMENT ADAPTIVE/MOBILITY: Brake pedal seal plate installation kit
- SP18-35H - EQUIPMENT: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
- SP18-35H - EQUIPMENT ADAPTIVE/MOBILITY: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
- SP18-39D - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Scr converter replacement - aftertreatment system
- SP18-35H - EQUIPMENT:MECHANICAL: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
- MI18-16B - ELECTRICAL SYSTEM: Bosch hd10 alternator diagnostic guide revision b to avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
- SP18-35H - POWER TRAIN: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
- SR19-31C - EQUIPMENT: Engine control module (ecm) software update - engine cooling strategy in high altitude operation revision c: vin range in application box rearranged for h3 coaches
- MI21-06 - FUEL SYSTEM, DIESEL: Diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair ⿿ from us10 to newer engine generation
- SP18-35F - POWER TRAIN: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency rev e: expiration date removed
- Mi21-07A - WHEELS: Ront & tag axle ⿿ unitized hub bearing end play verification and replacement
- IS-18042 - ELECTRICAL SYSTEM: Eberspacher preheater installation in replacement of spheros & valeo preheaters
- MI20-08C - STRUCTURE: Storage and startup guidelines: periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, prevost recommends foll
- IS-20925A - POWER TRAIN: Central hvac merv filters installation reva
- IS-18091A - STEERING: Tie rod 610052 first installation instructions: use these instructions when replacing the drop joint tie rod on s82, s84 / s84u i-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment ne
- MI20-19B - ENGINE AND ENGINE COOLING: Introducing a new engine coolant into prevost service center network
- MI20-19A - ENGINE AND ENGINE COOLING: Rev a: mention added concerning ddc series 60 engine sca requirement
- MI21-01 - EQUIPMENT: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
- MI21-01 - POWER TRAIN: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
- MI20-19 - EQUIPMENT: Introducing a new engine coolant into service
- MI20-08B - EQUIPMENT: Storage and startup guidelines revision: b parts added to suggested material 08-10-2020
- IS-20922 - EQUIPMENT ADAPTIVE/MOBILITY: Sigma passenger seats partition kit
- MI18-18B - EQUIPMENT: General hoisting and towing procedures revision: b updated 2.1 to show rubber chocks, secure front and rear.
- MI20-12 - STEERING: Jerky, noisy or hard to turn steering gearbox. Hydraulic end limiter adjustment. All models ⿿ equipped with rb bosch/zf servocom or servocomtronic steering gearbox
- MI20-08A - EQUIPMENT: Storage and startup guidelines: rev a: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
- NOx_Conv2 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P207F-00; P20EE-00
- NOX_Conv1 - EQUIPMENT ADAPTIVE/MOBILITY: Repair instructions to address fault codes P207F-00 - reductant quality
- FUELFILTER - ENGINE (PWS): Repair instructions to address fault codes P008A-00; P0087-00
- MI20-09 - EQUIPMENT:OTHER:LABELS: Prevost vehicle disinfection procedure
- MI20-08 - UNKNOWN OR OTHER: Storage and startup guidelines - all prevost vehicles & volvo 9700
- IS-19912A - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator - mention added stating to disable ⿿prime; parts added in the kit.
- IS-19901A - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator - x3 series us10 up to ghg17 cooling system - mention added stating to disable ⿿prime; parts added in the kit
- MI15-24 - EQUIPMENT ADAPTIVE/MOBILITY: Added: power cables for l.H. Side alternator & fan drive breaker box
- IS-19921A - EQUIPMENT: This instruction sheet explains how to install a seatbelt cutter in the driver's area
- IS-19066 - SERVICE BRAKES, AIR: This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
- SCI19-01C - ELECTRICAL SYSTEM: The intent of this procedure is to guide you through the steps required to program a mcm especially for the control of the electric fan drive as required for conversion kit of instruction sheets is-19900, is-19901, is19910, is-19912.
- IS-19901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system with bosch alternators on x3 series vehicles equipped with us10 up to ghg17 engines
- IS-17151 - LIGHTING (PWS): This instruction sheet explains how to replace halogen fog light to led's
- IS-19040A - STEERING: This instruction sheet explains how to replace power steering pump discharge hose (pressure) - #161335p or #160039
- SP18-35D_English - FUEL SYSTEM, DIESEL: On vehicles with active code P20EE, perform the following checklist and operations.
- IS-19901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system with bosch alternators on x3 series vehicles equipped with us10 up to ghg17 engines;
- IS-18091 - STEERING: This instruction sheet explains how to perform the first installation of tie rod 610052 on prevost vehicles equipped with dana s82, s84 / s84u i-beam axles, 1994- today
- SCI19-20 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the vehicle program has to be upgraded. This allows the intelligent sleep mode (ism) system improvement to prevent batteries drain when ism is enabled. This procedure shows how to generate the vehi
- Wb19-11 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the vehicle program might need to be upgraded to prevent batteries drain when ism (intelligent sleep mode) is enabled.
- IS-19915 - EQUIPMENT: Mp-1000 multimedia player installation
- IS-18158 - EQUIPMENT: Toilet drain valve replacement
- SP18-35B_English - ENGINE (PWS): On vehicles with active code P20EE, perform the following checklist and operations.
- IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet explains how to install a flap over the diesel filling cap
- IS-17071A - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
- SP18-39B - ENGINE (PWS): This special bulletin explains how to perform the replacement of the scr tank, when authorized.
- MI19-06 - BRAKES (PWS): This maintenance information is published to answer some questions regarding the inverted or ?Trailing? Mounting position of the drive axle brake calipers on prevost vehicles
- MI19-05 - EQUIPMENT: This maintenance information expains how to adjust p/n 660865, 660699 draglinks
- IS-17102A - EQUIPMENT: This instruction sheet explains how to install ism (intelligent sleep mode) on x series with prime hardware
- IS-19909 - ELECTRICAL SYSTEM: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles
- Sp18-39A - ENGINE AND ENGINE COOLING: This special bulletin explains how to perform the replacement of the scr tank, when authorized.
- SCI18-46 - EQUIPMENT:ELECTRICAL: This service center instructions explains how to install the prevost ultimate entertainment system
- Wb17-14B - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the power cable stud adapter on the alternator must be inspected and if needed, replaced.
- IS-18907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install hatches with fan on x3 vehicles.
- Sp18-35 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : On vehicles with active code P20EE, perform the following checklist and operations.
- WB18-04 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available.
- MI18-37 - POWER TRAIN:AUTOMATIC TRANSMISSION: This maintenance information presents information about the removal or installation of the lang kk73.1 electromagnetic clutch - part of the bitzer (model 4nfcy) air conditioning compressor.
- MI18-21A - ENGINE AND ENGINE COOLING: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
- MI18-18A - EQUIPMENT: This maintenance information explains how to tow and hoist prevost vehicles.
- MI18-05 - ENGINE AND ENGINE COOLING: This maintenance information explains how to install valve assembly 130009 in replacement of valve 641274
- MI16-17G - ENGINE AND ENGINE COOLING: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
- WB18-01A - STRUCTURE: On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
- WB18-07B - EQUIPMENT: On the vehicles affected by this bulletin, the busbar connected to circuit breaker cb13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper inst
- Sp18-20 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, replace the ac compressor discharge hose.
- MI18-18 - EQUIPMENT:MECHANICAL:WRECKER AND WHEEL LIFT DEVICES: This maintenance information explains how to tow and hoist prevost vehicles.
- IS-18901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the engine belt guard on x3 series vehicles with coolant system electrical fan drive.
- MI18-21 - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
- MI18-16A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information presents guidelines to help with the diagnosis of the bosch hd10 alternators
- IS-18902 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to installa parcel rack door kits
- WB18-15 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, the instrument cluster software must be updated. This mandatory cluster software update will raise the primary and secondary air system ?Low pressure warning? Set point.
- WB18-07 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the busbar connected to circuit breaker cb13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper inst
- IS-17905 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
- IS-13009B - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install and adjust drag link # 660699
- WB18-07A - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the busbar connected to circuit breaker cb13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper inst
- MI18-02 - ENGINE AND ENGINE COOLING: This mainteannce informaiton presents the latest engine oil & filter change intervals for the volvo engine
- MI16-17F - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
- IS-18901 - ENGINE AND ENGINE COOLING: This instruction sheet explains how to install an engine belt guard
- IS-15907A - EQUIPMENT:MECHANICAL: This instruction sheet explains how to assemble the bendix flr10 and flr20 radar sensor alignment tool
- MI15-24 - EQUIPMENT:MECHANICAL: This maintenance information explains how to perform an inspection of the vehicle power cables. Power cables in poor condition can be the cause of failures and serious damages in the engine compartment.
- IS-13169A - BRAKES (PWS): This instruction sheet explains how to install the aware adaptive cruise braking (acb) flr20 radar sensor replacement kits # 145372 and 145373
- IS-17907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the volvo electronic logging device (eld)
- IS-17071 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
- IS-17016 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruciton sheet explains how to relocate the rv-3 valve
- Wb18-01 - LATCHES/LOCKS/LINKAGES:DOORS:LATCH: On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
- MI17-22 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: This maintenance information explains how to inspect the fuel tank cradle mounting screws on a yearly basis
- Mi16-15 - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
- IS-16048 - LATCHES/LOCKS/LINKAGES: This instruction sheet explains how to install a wcl manual lock
- CK17-30 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is now possible to replace the older generation tgw 2.0 (3g network) by the newer 2.1 version (4g the network) using accessory kit 23266301 and the following procedure.
- MI15-40A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL: This maintenance information offers an overview of the operation of commuter bi-part doors.
- CK17-27 - EQUIPMENT ADAPTIVE/MOBILITY: This conversion kit explains how to to disable the acb radar.
- SP16-43A - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, coolant may leak by the coolant level sensor wires on the surge tank. Replace the sensor with an improved version.
- MI16-15B - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
- MI16-14 - SUSPENSION: Use this procedure when a suspension height check or adjustment must be performed.
- Mi16-28 - VISIBILITY:REARVIEW MIRRORS/DEVICES: This maintenance information explains that on vehicles equipped with ramco rear-view mirrors in winter conditions, ice may accumulate in the gap between the glass bottom edge and shell. The ice may impede mirror adjustment. Installing a dri
- MI16-27 - WHEELS: On vehicles operating in muddy road conditions, a road material ring may accumulate and harden inside the tag axle wheel. Depending on the hardness and abrasion potential of the dirt road material, the caliper body wall may wear out and thi
- MI16-15A - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
- MI16-16 - ELECTRICAL SYSTEM: This procedure explains how to perform a starter removal and installation, and does apply to melco 105p70 starter part number #21212425.
- MI16-05 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL: This maintenance information shares information about the bendix m-32qr valve replaced by m-40qr model htat need to be taken into consideration, specially when switching them for the first time on a vehicle.
- SP17-24A - EQUIPMENT:ELECTRICAL: On the vehicles affected by this bulletin, update the mux software to the latest version.
- CK17-26 - ENGINE (PWS): On the vehicles affected by this bulletin, it is now possible to disable the engine brake automatic function by running accessory kit # 23181730.
- SP17-23 - POWER TRAIN: On the vehicles affected by the bulletin, there is a possibility for the connection of the 12-24 volt power sensor to be reversed in the rear electrical box.
- SP17-07 - ELECTRICAL SYSTEM: On the vehicles affected by the bulletin, add protection circuit on a switch back of the engine switch engine shut down.
- SP17-25 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, it is possible that some of the electrical system decals applied to the vehicle structure need to be updated to reflect the current decal type and position currently used in production vehicles. In
- SP17-24 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update the mux software to the latest version.
- MI16-10A - SUSPENSION: This maintenance information applies only to vehicles equipped with 19000 lb independent front suspension (ifs) and 22.5 x 10.5 alcoa aluminum wheels for 365/70 r 22.5 size tires. When balancing this wheel for installation on the ifs, a spe
- IS-13169 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the aware adaptive cruise braking (acb) flr20 radar sensor replacement kits # 145372 and 145373
- MI16-17E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternator.
Known Recall Investigations
Alternator front bearing failure investigation # PE21011
Nhtsas office of defects investigation (odi) is opening a preliminary evaluation after receiving a tip from a fleet safety manager concerning alternator front bearing failures that cause elevated temperatures within the engine compartment, resulting in the fire suppression system (fss) activating, immediately shutting the engine down, and rendering the bus inoperable. Review of early warning reporting data identified 9 field reports for model year (my)2015 through my2019 h3 and x3 prevost buses, describing alternator failures in any of 3 alternators equipped on the bus. In some cases, a minor fire occurred damaging nearby electrical harnesses. An immediate shut down of the bus can increase the risk of a crash or injury of passengers when transferring to another bus.Odi is opening this investigation to evaluate the cause, consequence, scope and frequency of the alleged defect in the subject prevost buses.
NHTSA decoded information from VIN
1 Results returned successfully. NOTE: Any missing decoded values should be interpreted as NHTSA does not have data on the specific variable. Missing value should NOT be interpreted as an indication that a feature or technology is unavailable for a vehicle.
| Variable | Value |
|---|---|
| Body Class | Bus |
| Brake System Desc | Pneumatic system |
| Brake System Type | Air |
| Bus Length | 45 |
| DisplacementCC | 12800.0 |
| DisplacementCI | 781.10392441257 |
| DisplacementL | 12.8 |
| Engine Configuration | In-Line |
| Engine Cylinders | 6 |
| EngineHP | 435 |
| EngineHP_to | 500 |
| EngineKW | 324.3795 |
| Engine Manufacturer | Volvo |
| Engine Model | D13 |
| Error Text | 0 - VIN decoded clean. Check Digit (9th position) is correct |
| Fuel Type Primary | Diesel |
| Make | PREVOST |
| MakeID | 4148 |
| Manufacturer | VOLVO GROUP CANADA, INC |
| Manufacturer Id | 13545 |
| Model | X3 Passenger Coach |
| ModelID | 13606 |
| Model Year | 2017 |
| NCSA Body Type | Other Bus Type |
| NCSA Make | Other Make |
| NCSA Model | Bus: Rear engine, Flat front |
| Other Bus Info | Integral Structure |
| Plant City | STE-CLAIRE |
| Plant Country | CANADA |
| Plant State | QUEBEC |
| VIN | 2PCG33490HC736196 |
| Vehicle Descriptor | 2PCG3349*HC |
| Vehicle Type | BUS |
Latest VINs Decoded for this Manufacturer
| VIN | Year | Model | Manufactured In |
|---|---|---|---|
| 2PCG33491HC736174 | 2017 | X3 Passenger Coach | STE-CLAIRE QUEBEC, CANADA |
| 4RKG33499H9737357 | 2017 | X3 Passenger Coach | PLATTSBURGH NEW YORK, UNITED STATES (USA) |
| 4RKG33495H9737369 | 2017 | X3 Passenger Coach | PLATTSBURGH NEW YORK, UNITED STATES (USA) |
| 4RKG33498H9737348 | 2017 | X3 Passenger Coach | PLATTSBURGH NEW YORK, UNITED STATES (USA) |
| 2PCG33490HC736196 | 2017 | X3 Passenger Coach | STE-CLAIRE QUEBEC, CANADA |
| 4RKG33499H9737374 | 2017 | X3 Passenger Coach | PLATTSBURGH NEW YORK, UNITED STATES (USA) |
| 4RKG33497H9737406 | 2017 | X3 Passenger Coach | PLATTSBURGH NEW YORK, UNITED STATES (USA) |
| 2PCG33497HC736101 | 2017 | X3 Passenger Coach | STE-CLAIRE QUEBEC, CANADA |
| 4RKG33491H9737319 | 2017 | X3 Passenger Coach | PLATTSBURGH NEW YORK, UNITED STATES (USA) |
| 2PCG33496HC736168 | 2017 | X3 Passenger Coach | STE-CLAIRE QUEBEC, CANADA |
| 2PCG33495HC736131 | 2017 | X3 Passenger Coach | STE-CLAIRE QUEBEC, CANADA |
| 2PCG33495HC736128 | 2017 | X3 Passenger Coach | STE-CLAIRE QUEBEC, CANADA |
| 2PCG33497HC736096 | 2017 | X3 Passenger Coach | STE-CLAIRE QUEBEC, CANADA |