NTB19-072

Classification:
AT19-009
Reference:
Date:
NTB19-072
September 16, 2019
TRANSMISSION RANGE SWITCH SERVICE INFORMATION
2015-2017 Juke (F15)
APPLIED VEHICLES: 2017-2019 Sentra (B17)
2013-2018 Altima (L33)
2015-2017 Quest (E52)
2019 Altima (L34)
2014-2019 Rogue (T32)
2016-2019 Maxima (A36)
2017-2019 Rogue Sport (J11)
2015-2019 NV200 (M20)
2015-2019 Murano (Z52)
2014-2017 & 2019 Taxi (M20T) 2013-2019 Pathfinder (R52)
Sentra with MR16DDT (turbo) only
APPLIED ENGINE:
All other applied vehicles – all engines as equipped/available
APPLIED
RE0F10D, RE0F10E, RE0F10J, and RE0F10H
TRANSMISSIONS:
Does not apply to Hybrid models.
SERVICE INFORMATION
The transmission range switch of the APPLIED VEHICLES listed above is now available as
a separate service part.
If the transmission range switch of an APPLIED VEHICLE is being replaced for any
reason, it must be adjusted after its replacement.

Refer to SERVICE PROCEDURE on page 3 for transmission range switch removal,
installation, and adjustment.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/7
REQUIRED ESSENTIAL TOOL
CVT Transmission Range Switch (PNP) J-52306
Pin
Gauge
Figure 1
Additional quantities of Tool J-52306 may be purchased at Tech•Mate: 1-800-662-2001, or
nissantechmate.com.
2/7
NTB19-072
SERVICE PROCEDURE
IMPORTANT: Follow all warnings, cautions, and notes in the Electronic Service
Manual (ESM) when working under the hood, or on or near a Supplemental Restraint
System (SRS), such as an air bag.
Access the Transmission Range Switch
1.
Shift the selector lever to the Park (P) position.
2.
Gain access to the transmission range switch by loosening and moving, or removing
the parts listed in Table A.

Some connectors, such as an ECM connector, may need to be disconnected.

Some models have removal and installation procedures in the ESM.
Table A
*
ESM: section TRANSMISSION & DRIVELINE > TRANSAXLE & TRANSMISSION >
REMOVAL & INSTALLATION > TRANSMISSION RANGE SWITCH (PR25DD or
KR20DDET).
3/7
NTB19-072
Example of a transmission range switch and CVT (your vehicle may differ)
CVT or transaxle assembly
Figure 2
4/7
NTB19-072
Removal, Installation, and Adjustment – Transmission Range Switch
3.
After the transmission range switch is
accessible, remove the control cable
nut.
4.
Disconnect the transmission range
switch connector.
Disconnect
here
Remove nut
Figure 3
5.
Remove the manual lever nut, the lock
washer, and manual lever from the
manual shaft.
Remove nut,
washer, &
manual lever
The lock washer is a one-time use part
(this part is not to be reused after
removal).
Figure 4
6.
Remove the bolts, and then remove
the transmission range switch.
The transmission range switch is a
one-time use part (this part is not to be
reused after removal).
Remove
bolts
Figure 5
5/7
NTB19-072
7.
Install the replacement transmission range switch, and then install the bolts.

The bolts should be loose enough for the transmission range switch to pivot easily.
8.
Install the manual lever, but do not install the nut or the lock washer.
9.
Using the manual lever, shift the CVT into Neutral (N), and then remove the manual
lever.
10.
Assemble tool J-52306 (see Figure 6).
HINT: The pin can be threaded into
the gauge from either opening. Make
sure to insert and thread it into the
side shown in Figure 6.
J-52306
Gauge –
side view
Gauge –
top view
Pin
Figure 6
11.
Set tool J-52306 onto the manual shaft
while inserting its pin in the hole of the
transmission range switch (see
Figure 7).
J-52306
Figure 7
6/7
NTB19-072
12.
Tighten the bolts, and then remove
tool J-52306.

13.
…then remove tool
Bolt torque: 5.9 N•m (0.6 kg-m,
52 in-lbs)
Install the manual lever, nut, and new
lock washer.

Nut torque: 17.2 N•m (1.8 kg-m,
13 ft-lbs)
Tighten
Tightenbolts…
bolts
The lock washer is a one-time use part.
Replace the old one with a new one.
Figure 8
14.
Reassemble the vehicle in reverse order of disassembly.
15.
Verify:
a. The shift selector cannot be shifted out of Park without depressing the brake pedal.
b. The shift selector can be shifted out of Park with the brake pedal depressed.
PARTS INFORMATION
DESCRIPTION
PART NUMBER
QUANTITY
PARK/NEUTRAL POSITION SWITCH
(transmission range switch)
31918-29X0C
1
WASHER (lock washer)
08916-3401A
1
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
DIA
FRT
Replace Park/Neutral Switch
(1)
JD56AA
ZE
32
(2)
(1) Reference the Electronic Parts Catalog (EPC) and use the Park/Neutral Switch
(31918-*****) as the Primary Failed Part (PFP).
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat
Rate Time (FRT).
AMENDMENT HISTORY
PUBLISHED DATE
REFERENCE
September 16, 2019
NTB19-072
DESCRIPTION
Original bulletin published
7/7
NTB19-072