Ford F-250 Sd 2005

• Recall 146009 [USA]: If the steering locks, it can increase the risk of a crash.
  Icon vehicle dynamics, llc (icon) is recalling all 05-up fsd 2.5 centerline stabilizer kits with part number 65050. The kits were sold as an accessory for certain 2005-2021 ford f-250 4x4 and f-350 4x4 pickup trucks. The foam ring inside the stabilizer "through shaft" may block the piston ports, possibly causing the steering to lock up.
  icon will notify owners, and dealers will install a new shock assembly with a revised foam ring and steel support disc, free of charge. The recall began december 21, 2020. Owners may contact icon customer service at 1-951-689-4266.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 70719 [USA]: Non-functioning lights could increase the risk of a crash.
  Ford is recalling certain model year 2011 ranger trucks built from january 25, 2011, through april 25, 2011 at the twin cities assembly plant, and service parts distributed to dealers for certain 2004 through 2011 model year ranger trucks, 2002 through 2005 model year excursion vehicles, and 2002 through 2007 model year f-250, f-350, f-450, and f-550 trucks for failing to comply with the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment." the multi-function switch was shipped with a subcomponent (slider) that may experience deformation. A multi-function switch with a deformed slider may malfunction causing the turn signal, tail lights, hazard warning signal flashers and/or brake lights not to activate.
  dealers will replace the switches free of charge. The safety recall began on august 15, 2011. Owners may contact ford motor company customer relationship center at 1-866-436-7332.
  ford's safety recall no. 11c18.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 83600 [USA]: Decreased lighting visibility may result in a vehicle crash.
  Sabersport is recalling 16,270 combination corner and bumper lamp assemblies of various part numbers sold for use as aftermarket equipment for various passenger vehicles. These headlamps fail to conform to the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment." these lamps do not contain the required amber side reflectors.
  sabersport will notify owners and offer a full refund for the noncompliant combination lamps. The safety recall began on may 11, 2009. Owners may contact sabersport at 1-909-598-7589.
  this recall only pertains to aftermarket replacement equipment and has no relation to any original equipment installed on vehicles produced by the vehicle manufacturer.In order to determine if your aftermarket lamp assembly is affected by this noncompliance, please review the list of model numbers provided to us by sabersport.The list can be found under "document search" located at the bottom of your screen.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 83943 [USA]: A lift occupant can be injured should the lift begin to stow unintentionally.
  Comm trans is recalling 108 my 2005-2008 ford e250 and e350 vans built on ford chassis and equipped with ricon platform style wheelchair lifts. These lifts fail to comply with the requirements of federal motor vehicle safety standard no. 403, "platform lift system accessible for motor vehicles." the anti-stow interlock may not detect the presence of a wheelchair or mobility aid user. The pressure sensing switch that detects the presence of weight on the platform was not adjusted to the necessary sensitivity level. The lift could stow even though someone or something is still on the lift.
  comm trans is working with ricon to correct the wheelchair lifts free of charge (please see 07e097). Owners may contact ricon at 1-818-267-3000 or comm trans at 901-726-9394.
  customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 87450 [USA]: The user of the lift could be injured should the lift move unintentionally.
  Comm trans is recalling 111 my 2005-2008 ford e250 and e350 vans built on ford chassis and equipped with ricon platform style wheelchair lifts. These vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 404, "platform lift installations on motor vehicles." the threshold warning system may not detect the presence of a wheelchair or mobility aid user in a certain spot within the defined threshold area.
  comm trans is working with ricon to correct the wheelchair lifts free of charge (please see 07e095). Owners may contact ricon at 1-818-267-3000 or comm trans at 901-726-9394.
  customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 75251 [USA]: This could allow possible shifting and damage to the rear drive shaft and axle.
  Truxxx is recalling 338 aftermarket replacement welded 3" lift blocks for rear suspensions, part no. 206073, included in suspension kit nos. 108035 and 108036, sold between july 26, 2007 and march 4, 2008, for use on ford my 2005-2008 f-250 superduty 4x4 light trucks. Compressive forces of the welded lift blocks resulting from foreseeable and excess vehicle payloads as well as over-tightening of the u-bolts during installation may distort the blocks, reducing the intended clamping force of the u-bolts.
  truxxx will notify customers/installers and will replace affected welded lift blocks with either non-welded aluminum or cast iron blocks free of charge. The recall is expected to begin on or about april 16, 2008. Owners may contact truxxx at 1-800-381-8320.
  truxxx recall no. 08-01blk.This recall only pertains to aftermarket suspension kits and has not relation to any original equipment installed on ford motor company vehicles.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 50050 [USA]: Brake failure can occur, possibly resulting in a vehicle crash.
  Certain harsco wheel modification groups containing accuride steel rims, p/nos. 203237 and 203738; accuride aluminum rims, p/n 203712; and gkn steel rims, p/n 203688, sold as modification equipment for certain 2005-2007 ford f-250/f-350 4x4 pickup trucks to modify track width of front and rear axles. The rims provided in these wheel modification groups wear through the oem brake lines.
  harsco will notify owners and provide a repair kit along with repair instructions free of charge. The recall began in september 2006. Owners may contact harsco at 507-235-7112.
  harsco recall no. #06-006.This recall only pertains to modification kits manufactured by harsco and has no relation to any original equipment installed on ford f-250 and f-350 4x4 pickup trucks manufactured by the ford motor company.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 36134 [USA]: Should the engine stall, a vehicle crash could occur.
  Certain pickup trucks, sport utility vehicles and vans equipped with 6.0l diesel engines may experience stalling without warning while driving and may or may not restart.
  dealers will upgrade the fuel injection control module (ficm) wire harness or replaced, and/or have a new injection control pressure (icp)) sensor connector installed free of charge. The recall began on july 22, 2005. Owners may contact ford at 1-800-392-3673.
  ford recall no. 05s34.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 36064 [USA]: The fuel line may separate at the connection to the main fuel bundle. if the fuel line separates, an operator may notice a gasoline odor and/or fuel on the ground, loss of power, and the engine will eventually stall. fuel leakage in the presence of an ignition source could result in a fire.
  On certain pickup trucks and chassis cab vehicles equipped with 5.4l or 6.8l gasoline engines, the fuel jumper line may have an incorrect end form.
  dealers will install an external retention clip at the fuel jumper line to the main fuel bundle connection. The recall began on june 20, 2005. Owners may contact ford at 1-800-392-3673.
  ford recall no. 05s33.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Violent front end oscillation investigation # EA08007

  This investigation was opened based on 78 consumer complaints of severe suspension and steering wheel oscillations after the subject vehicles traveled over an uneven surface.Odi was concerned about these complaints because many of them alleged loss of control and the loss of control occurredat speeds above 50 miles per hour.At the time these complaints were received, odi was also aware of the tsb 07-10-10 and early warning field reports that discussed the shimmy condition on the subject vehicles.Since opening this investigation, odi has confirmed, based on consumer complaints, warranty data, testing conducted by vrtc, and odi inspection of complaint vehicles, that the owners of the subject vehicles are experiencing shimmy events on their vehicles.However, odi has also confirmed that owners typically do not maintain their tires at the pressures recommended by ford on the tire label.Further, odi has found that in order for shimmy to occur, tire pressures must be substantially below (at least 20%) those specified on the vehicle tire label.Odi considers these unsafe tire conditions to be the result of one of three typical situations.The tires are being improperly maintained, the owners are intentionally setting the tire pressures low to enhance ride quality, or aftermarket tires (not designed for use on the vehicle) are installed to change the appearance or function of the vehicle.The subject vehicles are intended and designed to be used as heavy duty vehicles and as such require that the tires be capable of handling the loads for which the vehicle is designed and marketed.In order for the tires to be capable of handling these loads, the proper tire pressure must be maintained.In light of the information gathered in this investigation and fords agreement to notify subject vehicle owners (now and every two years until the vehicles reach ten years from their production date) about the importance of maintaining proper tire pressures on their vehicles, further use of agency resources does not appear to be warranted.The closing of this investigation does not constitute a finding by nhtsa that no safety-related defect exists.The agency reserves the right to take further action if warranted by the circumstances.For additional information, see the attached closing report.
  

  Show Content

A scary and serious wobble at 35 mph. Had to creep home. Almost lost control.

A scary and serious wobble at 35 mph. Had to creep home. Almost lost control.

Cruise control would not disengage. When my husband pressed the brakes, the car sped up. We had to pass 5 vehicles, barely enough room. He finally turned the motor off and was able to pull off the freeway (i70). But for the grace not god, we would have died of injured ourselves and others. Brakes should never make your car speed up.

Cruise control would not disengage. When my husband pressed the brakes, the car sped up. We had to pass 5 vehicles, barely enough room. He finally turned the motor off and was able to pull off the freeway (i70). But for the grace not god, we would have died of injured ourselves and others. Brakes should never make your car speed up.

The ford 250 initiates a 'death wobble' or intense shimmy in the front wheels at speeds greater than 50 mph anytime any small bump is encountered on road. This instance initiated 5 times in a 500 mile highway trip at such an intense rate that the vehicle lost significant steering control and had to be immediately decelerated to nearly 20 mph for it to stop. Initial speed was close to 63 mph. The shimmy initiated when a small bump is passed over and on three of these instances it initiated with the crossing of a expansion gap or transition from the highway to a bridge or bridgelike structure. The wobble shook truck so much that directional control was lost. Approaching (traffic from the rear) had to swerve out of they way to avoid a rear collision. If deceleration is not immediately imposed the vehicle maintains the shimmy and directional control is severely compromised. In two instances on this trip i was able to nurse the wobbling vehicle off the road to the shoulder to then brake till control could be retrieved. However, there are many instances when access to the right side is impeded such as when passing in left lane. The same issue has happened before on a highway trip to another state 6 months before.

The ford 250 initiates a 'death wobble' or intense shimmy in the front wheels at speeds greater than 50 mph anytime any small bump is encountered on road. This instance initiated 5 times in a 500 mile highway trip at such an intense rate that the vehicle lost significant steering control and had to be immediately decelerated to nearly 20 mph for it to stop. Initial speed was close to 63 mph. The shimmy initiated when a small bump is passed over and on three of these instances it initiated with the crossing of a expansion gap or transition from the highway to a bridge or bridgelike structure. The wobble shook truck so much that directional control was lost. Approaching (traffic from the rear) had to swerve out of they way to avoid a rear collision. If deceleration is not immediately imposed the vehicle maintains the shimmy and directional control is severely compromised. In two instances on this trip i was able to nurse the wobbling vehicle off the road to the shoulder to then brake till control could be retrieved. However, there are many instances when access to the right side is impeded such as when passing in left lane. The same issue has happened before on a highway trip to another state 6 months before.

When driving, the truck will die. Sometimes truck can be restarted other times had to have it tolled. We have replaced fuel pressure regulator, regulator, start switch r&r instrument cluster, alternator, batteries and the problem still exist. Have taken it to a ford dealer and they can not find the problem. They say it is not covered on recall 05v270000

When driving, the truck will die. Sometimes truck can be restarted other times had to have it tolled. We have replaced fuel pressure regulator, regulator, start switch r&r instrument cluster, alternator, batteries and the problem still exist. Have taken it to a ford dealer and they can not find the problem. They say it is not covered on recall 05v270000

2005 ford f250 with approximately 19,100 miles. Original factory tires, suspension- no modifications. Tire pressure set to factory door label specs. On monday, 8-19-2019 while on i-95, travel speed at about 60 m.P.H., i drove over a bridge expansion joint & the entire truck started shaking violently. Steering wheel was vibrating/shaking making it difficult for me to maintain control of the truck in my established lane and nearly took out several cars in the adjacent lanes nearly causing multi-vehicle collision. Went on the internet & found thousands of similar complaints regarding this same issue i just experienced. Later found out it is called harmonic resonance a.K.A. The death wobble. This dangerous situation affects not only the driver and the passengers in the defective vehicle, but to other unsuspecting motorist's and their passengers whom share the same roadways.

Common OBD-II Error Codes

• P0191 [1] Fuel Rail Pressure Sensor A Circuit Range/Performance
• P0401 [2] Exhaust Gas Recirculation Flow Insufficient Detected
• P0402 [1] Exhaust Gas Recirculation Flow Excessive Detected
• P0404 [3] Exhaust Gas Recirculation Circuit Range/Performance
• P1335 [1] Fuel injection pump control module - CKP signal missing
• P0300 [3] Random/Multiple Cylinder Misfire Detected
• P0500 [3] Vehicle Speed Sensor "A" Malfunction
• P0503 [2] Vehicle Speed Sensor "A" Intermittent/Erratic/High
• C1175 [2] Speed Wheel Sensor LR Input Circuit Failure
• C1236 [2] Speed Wheel LR Input Signal Missing
• P0103 [1] Mass or Volume Air Flow "A" Circuit High Input
• P2138 [1] Throttle/Pedal Pos Sensor/Switch D / E Voltage Correlation
• P2139 [1] Throttle/Pedal Pos Sensor/Switch D / F Voltage Correlation
• P2140 [1] Throttle/Pedal Pos Sensor/Switch E / F Voltage Correlation
• P2263 [5] Turbocharger/Supercharger Boost System Performance
• P0238 [1] Turbocharger Boost Sensor A Circuit High
• P0299 [5] Turbocharger/Supercharger "A" Underboost Condition
• P2262 [1] Turbocharger/Supercharger Boost Pressure Not Detected - Mechanical
• P0340 [3] Camshaft Position Sensor Circuit Malfunction (Bank 1)
• P0344 [3] Camshaft Position Sensor A Circuit Intermittent (Bank 1)
• P0345 [2] Camshaft Position Sensor A Circuit Malfunction (Bank 2)
• P0349 [2] Camshaft Position Sensor A Circuit Intermittent (Bank 2)
• P0460 [2] Fuel Level Sensor Circuit Malfunction
• P0316 [3] Misfire Detected On Startup (First 1000 Revolutions)
• P2106 [2] Throttle Actuator Control System - Forced Limited Power
• P0172 [2] System too Rich (Bank 1)
• P0175 [2] System too Rich (Bank 2)
• P2195 [1] O2 Sensor Signal Stuck Lean Bank 1 Sensor 1
• P2196 [1] O2 Sensor Signal Stuck Rich Bank 1 Sensor 1
• P2197 [1] O2 Sensor Signal Stuck Lean Bank 2 Sensor 1
• P2198 [1] O2 Sensor Signal Stuck Rich Bank 2 Sensor 1
• P0308 [1] Cylinder 8 Misfire Detected
• P0171 [1] System too Lean (Bank 1)
• P0174 [1] System too Lean (Bank 2)
• P2104 [1] Throttle Actuator Control System - Forced Idle