Prevost X3-vip 2015
Vehicle Details: Recalls, Investigations, Service Bulletins
Below you will find all available information on the 2015 PREVOST X3-vip.
| Manufacturer | Known WMI(s) | Fuel Type |
|---|---|---|
| PREVOST |
PREVOST VIN Decoder
Use the box here to look up VINs from PREVOST as well as other manufacturers
Frequently Asked Questions
-
Are there recalls for the 2015 PREVOST X3-vip?
- There are 1 recall(s) for the 2015 PREVOST X3-vip, additional information is below.
NHTSA Mandated Recalls
Recall 109941 [USA]: Contact between the fuel line and the coolant line may cause a fuel leak and result in fuel spraying onto hot exhaust components increasing the risk of an engine compartment fire.
To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.
Bulletins
Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.
- MI16-32 - ENGINE AND ENGINE COOLING: Improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
- IS-19912E - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with delco remy alternator. Revision: e note added regarding power cable connection
- IS-21072B - ELECTRICAL SYSTEM: Steering gateway. Revision b - pin 2 and 10 were inverted on connector a139
- MI22-12B - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: b - general update
- MI22-12A - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: a - erroneous secondary & accessory tanks location.
- MI22-12 - SERVICE BRAKES, AIR: Air tanks draining sequence
- IS-17151C - EXTERIOR LIGHTING: Halogen to led fog light replacement kit. Revision: c - advanced kits canceled
- IS-22902 - WHEELS: Tag axle hub flange - alternate cap screw
- IS21-072 - ELECTRICAL SYSTEM: Steering gateway, revision a : cancel watch dog removal from efd part of the instruction
- MI20-08C - EQUIPMENT: Storage and startup guidelines : part number updates
- IS21-901 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : X3 series envirocare - ions air sanitizer
- IS21-072A - ELECTRICAL SYSTEM: Steering gateway revision a cancel watch dog removal from efd part of the instruction
- IS20-925A - VISIBILITY: Central hvac merv filters installation
- IS22-040 - EQUIPMENT ADAPTIVE/MOBILITY: Brake pedal seal plate installation kit
- MI18-16B - ELECTRICAL SYSTEM: Bosch hd10 alternator diagnostic guide revision b to avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
- MI21-06 - FUEL SYSTEM, DIESEL: Diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair ⿿ from us10 to newer engine generation
- Mi21-07A - WHEELS: Ront & tag axle ⿿ unitized hub bearing end play verification and replacement
- IS-18042 - ELECTRICAL SYSTEM: Eberspacher preheater installation in replacement of spheros & valeo preheaters
- MI20-08C - STRUCTURE: Storage and startup guidelines: periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, prevost recommends foll
- IS-20925A - POWER TRAIN: Central hvac merv filters installation reva
- SP21-300 - EQUIPMENT: Automatic fire suppression system - tamper seal replacement
- IS-18091A - STEERING: Tie rod 610052 first installation instructions: use these instructions when replacing the drop joint tie rod on s82, s84 / s84u i-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment ne
- MI20-19B - ENGINE AND ENGINE COOLING: Introducing a new engine coolant into prevost service center network
- MI20-19A - ENGINE AND ENGINE COOLING: Rev a: mention added concerning ddc series 60 engine sca requirement
- MI21-01 - EQUIPMENT: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
- MI21-01 - POWER TRAIN: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
- MI20-19 - EQUIPMENT: Introducing a new engine coolant into service
- MI16-17D - SEATS: Use this procedure for the removal and installation of the twin bosch hd10 (120a or 150a) alternators.
- MI20-08B - EQUIPMENT: Storage and startup guidelines revision: b parts added to suggested material 08-10-2020
- IS-20922 - EQUIPMENT ADAPTIVE/MOBILITY: Sigma passenger seats partition kit
- MI18-18B - EQUIPMENT: General hoisting and towing procedures revision: b updated 2.1 to show rubber chocks, secure front and rear.
- MI20-12 - STEERING: Jerky, noisy or hard to turn steering gearbox. Hydraulic end limiter adjustment. All models ⿿ equipped with rb bosch/zf servocom or servocomtronic steering gearbox
- MI20-08A - EQUIPMENT: Storage and startup guidelines: rev a: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
- NOx_Conv2 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P207F-00; P20EE-00
- NOX_Conv1 - EQUIPMENT ADAPTIVE/MOBILITY: Repair instructions to address fault codes P207F-00 - reductant quality
- FUELFILTER - ENGINE (PWS): Repair instructions to address fault codes P008A-00; P0087-00
- MI20-09 - EQUIPMENT:OTHER:LABELS: Prevost vehicle disinfection procedure
- MI20-08 - UNKNOWN OR OTHER: Storage and startup guidelines - all prevost vehicles & volvo 9700
- IS-19912A - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator - mention added stating to disable ⿿prime; parts added in the kit.
- IS-19901A - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator - x3 series us10 up to ghg17 cooling system - mention added stating to disable ⿿prime; parts added in the kit
- MI15-24 - EQUIPMENT ADAPTIVE/MOBILITY: Added: power cables for l.H. Side alternator & fan drive breaker box
- IS-19066 - SERVICE BRAKES, AIR: This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
- SCI19-01C - ELECTRICAL SYSTEM: The intent of this procedure is to guide you through the steps required to program a mcm especially for the control of the electric fan drive as required for conversion kit of instruction sheets is-19900, is-19901, is19910, is-19912.
- IS-19901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system with bosch alternators on x3 series vehicles equipped with us10 up to ghg17 engines
- IS-17151 - LIGHTING (PWS): This instruction sheet explains how to replace halogen fog light to led's
- IS-19040A - STEERING: This instruction sheet explains how to replace power steering pump discharge hose (pressure) - #161335p or #160039
- SP19-301 - EQUIPMENT: On the vehicles affected by this bulletin, the compressor & radiator door lower hinges must be replaced by new stainless steel units
- IS-19901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system with bosch alternators on x3 series vehicles equipped with us10 up to ghg17 engines;
- IS-18091 - STEERING: This instruction sheet explains how to perform the first installation of tie rod 610052 on prevost vehicles equipped with dana s82, s84 / s84u i-beam axles, 1994- today
- IS-19922 - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: Prevost aware adaptive cruise braking (acb) flr10 to flr21 radar sensor upgrade
- IS-19915 - EQUIPMENT: Mp-1000 multimedia player installation
- WB19-07 - SERVICE BRAKES, AIR: On the independent front suspension (ifs) of the vehicles affected by this bulletin, check and make sure that there is enough clearance between the brake hoses identified in the procedure and their respective support bracket.
- IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet explains how to install a flap over the diesel filling cap
- IS-17071A - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
- MI19-06 - BRAKES (PWS): This maintenance information is published to answer some questions regarding the inverted or ?Trailing? Mounting position of the drive axle brake calipers on prevost vehicles
- MI19-05 - EQUIPMENT: This maintenance information expains how to adjust p/n 660865, 660699 draglinks
- IS-19909 - ELECTRICAL SYSTEM: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles
- SCI18-46 - EQUIPMENT:ELECTRICAL: This service center instructions explains how to install the prevost ultimate entertainment system
- Wb17-14B - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the power cable stud adapter on the alternator must be inspected and if needed, replaced.
- IS-18907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install hatches with fan on x3 vehicles.
- SP18-307 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, the bitzer compressor shaft seal must be replaced. Additionally, the compressor oil must be renewed and the oil quantity increased by 10oz (300ml).
- Sp18-302 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, install a pressure switch into the front service compartment to send a faster signal to the allison transmission to switch to neutral at stop.
- SP18-306 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available.
- WB18-04 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available.
- SP18-305A - LATCHES/LOCKS/LINKAGES: On the vehicles affected by this bulletin, apply thread locker on the double door latch pins internal threads
- MI18-37 - POWER TRAIN:AUTOMATIC TRANSMISSION: This maintenance information presents information about the removal or installation of the lang kk73.1 electromagnetic clutch - part of the bitzer (model 4nfcy) air conditioning compressor.
- MI18-21A - ENGINE AND ENGINE COOLING: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
- MI18-18A - EQUIPMENT: This maintenance information explains how to tow and hoist prevost vehicles.
- MI18-05 - ENGINE AND ENGINE COOLING: This maintenance information explains how to install valve assembly 130009 in replacement of valve 641274
- MI16-17G - ENGINE AND ENGINE COOLING: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
- WB16-02H - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system.
- IS-15003E - ELECTRICAL SYSTEM: This insruction sheet explains how to insall the bosch hd10 24v-150a alternator conversion kit ? Twin bosch mounted on volvo d13 engine
- Sp18-304A - EQUIPMENT:MECHANICAL: For vehicles affected by this bulletin, on the wheelchair area sliding door, install a new upper roller carrier, adjust the door and inspect all fasteners.
- Sp18-303 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, the condenser compartment wall may present fatigue cracks on or near the a/c receiver tank support. Follow these instructions to repair and improve the support.
- Sp18-301 - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK ASSEMBLY: On the vehicles affected by this bulletin, the existing surge tank support has to be replaced by a new configuration including two supports. That will allow a better distribution of the load between the tank and the support.
- MI18-18 - EQUIPMENT:MECHANICAL:WRECKER AND WHEEL LIFT DEVICES: This maintenance information explains how to tow and hoist prevost vehicles.
- SP17-314-R13 - INTERIOR LIGHTING: This bulletin explains how to install a light at the entrance door.
- MI18-21 - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
- MI18-16A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information presents guidelines to help with the diagnosis of the bosch hd10 alternators
- WB18-15 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, the instrument cluster software must be updated. This mandatory cluster software update will raise the primary and secondary air system ?Low pressure warning? Set point.
- IS-17905 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
- IS-13009B - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install and adjust drag link # 660699
- WB15-19H - EQUIPMENT:APPLIANCE:AIR CONDITIONER: This bulletin explains how to add a reinforcement bracket to bitzer a/c compressor to increase the installation stiffness and reduce vibration amplitude.
- SP17-314 - INTERIOR LIGHTING: This bulletin explains how to install a light at the entrance door.
- MI18-02 - ENGINE AND ENGINE COOLING: This mainteannce informaiton presents the latest engine oil & filter change intervals for the volvo engine
- MI16-17F - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
- MI1434C - VEHICLE SPEED CONTROL:CRUISE CONTROL: This maintenance information presents how to align the prevost aware adaptive cruise braking (acb)flr20 radar sensor.
- WB14-06G - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, perform the following verifications and modifications on the a/c system: bulletin is divided in five steps, refer to detailed instructions below. Step 1: unloader replacement (step moved to war
- SP15-60 - STEERING: On the vehicles affected by this bulletin, there is a contact possibility between some parts of the ifs suspension components and steering linkage when the wheels are rotated to their maximum left or right position and the suspension is ful
- WB15-50 - EQUIPMENT:OTHER:LABELS: On the vehicles affected by this bulletin the rear junction box decal located in the right engine compartment is displaying incorrect information regarding the r34 relay voltage. Specifically, the r34 relay should be identified as a 24 v
- IS-15907A - EQUIPMENT:MECHANICAL: This instruction sheet explains how to assemble the bendix flr10 and flr20 radar sensor alignment tool
- WB15-53A - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles covered by this bulletin, two dpf (diesel particulate filter) plugs may be loose. If a plug is loose, it may fall out under the effect of vibration. This may cause leakage of hot exhaust gases. It is therefore necessary to c
- WB15-46 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL: On the vehicles affected by this bulletin the epa (us environment protection agency) decal located in the engine compartment displays incorrect information related to the vehicle emission control. Specifically, the first character, indicati
- MI15-41 - EXTERIOR LIGHTING:TAIL LIGHTS: This maintenance information reminds prevost customers that cleaning products designed for external washing of vehicles should be used for exterior vehicle wash and in particular, for the washing of polycarbonate taillights.
- MI15-43 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on prevost vehicles equipped with bosch hd10 alternators.
- MI15-18 - EQUIPMENT: This maintenance information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.
- MI15-24 - EQUIPMENT:MECHANICAL: This maintenance information explains how to perform an inspection of the vehicle power cables. Power cables in poor condition can be the cause of failures and serious damages in the engine compartment.
- SP15-23 - SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY:U-BOLT, LEAF SPRING TO AXLE: On the vehicles affected by this bulletin, the bolts of the steer lever might not be per specifications. Inspect per procedure below and replace as needed.
- WB15-10 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, inspect the lower oil fill tube flexible tube. If it is made of black material (edpm), replace tube. Green and blue silicone hoses are accepted.
- IS-15003A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to use the bosch hd10 24v-150a altenrator conversion kit
- SP15-15A - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform software updates of the engine management system (ems) and instrument cluster. The cluster update affects the beep sound level. Some vehicles will need both systems updated. Other vehicles
- IS-13169A - BRAKES (PWS): This instruction sheet explains how to install the aware adaptive cruise braking (acb) flr20 radar sensor replacement kits # 145372 and 145373
- IS-17907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the volvo electronic logging device (eld)
- SP17-314 - INTERIOR LIGHTING: On the vehicles affected by this bulletin, install a light at the entrance door.
- SP17-313 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, replace the batteries by a new set (4) of the same model; perform several verifications on the alternator and charging circuit. Finally, update the multiplex software to the latest version and disa
- IS-17071 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
- IS-17016 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruciton sheet explains how to relocate the rv-3 valve
- Sp18-300 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This bulletin explains how to replace ceiling transition pannels, when needed
- MI17-22 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: This maintenance information explains how to inspect the fuel tank cradle mounting screws on a yearly basis
- WB15-06C - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: On the vehicles affected by this bulletin, inspect the serial number of the current sensors in the battery compartment and follow instructions to perform replacement if applicable. A number of sensors have been identified by the manufacture
- WB15-06B - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, inspect the serial number of the current sensors in the battery compartment and follow instructions to perform replacement if applicable. A number of sensors have been identified by the manufacture
- IS-13106 - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install an improved version of the slide-out rails. This version of the rails offers better corrosion resistance.
- MI15-02 - POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT: This maintenance information presents an improved differential breather kit, identical to the one now used in production. This new breather incorporates a "j" shaped hose that prevents oil leakage and water ingestion while allowing the axle
- WB14-47B - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, perform a software update of ecm (engine control module) and acm (aftertreatment control module) to provide improved temperature-related behaviour. The software will also change urea dosing valve b
- Wb15-19F - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
- Mi16-15 - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
- SP16-304 - EQUIPMENT:OTHER:LABELS: On the vehicles affected by this bulletin, replace the battery connection decal by a new version.
- IS-14154 - FUEL SYSTEM, GASOLINE: This instruction sheet explains how to modify the support beam (part # 30022 installation)- as part of the x3 fuel tank installation
- WB17-02 - ENGINE AND ENGINE COOLING: This bulletin explains how install an extension to the linear thermal detector (ltd) over the alternators
- SP17-307 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: This bulletin explains how to replace the radiator door upper hinge
- SP17-303D - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, replace two idlers by an improved version on the alternator drive belt and on the a/c belts.
- IS-16048 - LATCHES/LOCKS/LINKAGES: This instruction sheet explains how to install a wcl manual lock
- IS-15003D - ELECTRICAL SYSTEM: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
- CK17-30 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is now possible to replace the older generation tgw 2.0 (3g network) by the newer 2.1 version (4g the network) using accessory kit 23266301 and the following procedure.
- Sp16-323 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, change a parameter in the mux system to deactivate a dtc corresponding to air dryer cartridge change warning.
- WB15-38A - VISIBILITY/WIPER (PWS): On the vehicles affected by this bulletin, add an extrusion to the wiper arms to support the washer fluid hose.
- WB15-19 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
- MI15-40A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information offers an overview of the operation of commuter bi-part doors.
- WB15-10A - ENGINE (PWS): On the vehicles affected by this bulletin, inspect the lower oil fill tube flexible tube. If it is made of black material (edpm), replace tube. Green and blue silicone hoses are accepted.
- SP15-37 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, seal a tube passage between the auxiliary heater compartment and the heating duct in the passenger's compartment.
- SP15-15B - ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL: On the vehicles affected by this bulletin, perform software updates of the engine management system (ems) and instrument cluster. The cluster update affects the beep sound level. Some vehicles will need both systems updated. Other vehicles
- WB15-06D - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, inspect the serial number of the current sensors in the battery compartment and follow instructions to perform replacement if applicable. A number of sensors have been identified by the manufacture
- Sp17-312A - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: On the vehicles affected by this bulletin, bus washing operations can result in water dripping into the front service compartment. Add a drip guard above the entrance door valve.
- CK17-27 - EQUIPMENT ADAPTIVE/MOBILITY: This conversion kit explains how to to disable the acb radar.
- SP16-43A - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, coolant may leak by the coolant level sensor wires on the surge tank. Replace the sensor with an improved version.
- SP16-326 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, re-torque the clamps on specific coolant hoses of the cooling system.
- SP16-311B - EQUIPMENT: On the vehicles affected by this bulletin, add two clips to secure the direct light lenses, 13 lenses per vehicle.
- IS-15003B - EQUIPMENT: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
- MI16-15B - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
- WB16-02B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system.
- Sp16-309A - ENGINE (PWS): On the vehicles affected by this bulletin, secure the mounting of the curb side engine door electrical fan.
- Sp16-303C - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, reposition the harness out of the path of an unlocked electrical box door.
- Sp16-300C - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, improvement of a charge air cooler tube support is required.
- Wb16-29 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available. This update must be carried out by qualified technicians. As soon as possible, make an appointment with your nearest prevost service cen
- Sp16-317 - BRAKES (PWS): On the vehicles affected by this bulletin, it is necessary to ensure proper brake pedal installation and adjustment following the procedure below.
- IS-16902 - BRAKES (PWS): This instruction sheet explains how to install and adjust brake pedal kit is16902
- MI16-14 - SUSPENSION: Use this procedure when a suspension height check or adjustment must be performed.
- Mi16-28 - VISIBILITY:REARVIEW MIRRORS/DEVICES: This maintenance information explains that on vehicles equipped with ramco rear-view mirrors in winter conditions, ice may accumulate in the gap between the glass bottom edge and shell. The ice may impede mirror adjustment. Installing a dri
- WB16-02 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system.
- SP16-306A - WHEELS: On the vehicles affected by this bulletin, replace an access panel aft of the tag axle wheel, road side.
- Sp16-302A - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK ASSEMBLY: On the vehicles affected by this bulletin, replace the pressure cap on the surge tank.
- Sp16-313A - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, coolant may leak by the coolant level sensor wires on the surge tank. Replace the sensor with an improved version.
- Sp16-311A - EQUIPMENT: On the vehicles affected by this bulletin, add two clips to secure the direct light lenses, 13 lenses per vehicle.
- IS-14220B CO-06 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL: This instruction sheet explains how to install fuel pro filter
- Sp16-303B - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, reposition the harness out of the path of an unlocked electrical box door.
- SP16-306 - WHEELS: On the vehicles affected by this bulletin, replace an access panel aft of the tag axle wheel, road side.
- MI16-23 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information explains that decals are available to update the front junction box on 2013 to 2016 prevost vehicles; the decals will provide updated information and component descriptions. Refer to the identification part of t
- MI16-15A - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
- MI16-10 - WHEELS: This information letter applies only to vehicles equipped with 19000 lb independent front suspension (ifs) and 22.5 x 10.5 alcoa aluminum wheels for 365/70 r 22.5 size tires. When balancing this wheel for installation on the ifs, a specifi
- Sp16-309 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, secure the mounting of the curb side engine door electrical fan.
- SP16-300B - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, improvement of a charge air cooler tube support is required.
- MI16-16 - ELECTRICAL SYSTEM: This procedure explains how to perform a starter removal and installation, and does apply to melco 105p70 starter part number #21212425.
- MI16-12 - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information explains how to perform the replacement of glued fixed thermos window. This procedure may also be used for the replacement of non-thermos fixed window as the installation method is similar.
- SP16-303 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, reposition the harness out of the path of an unlocked electrical box door.
- SP15-304E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: On the vehicles affected by this bulletin, the bosch hd10 alternators need to be replaced with new bosch hd10plbh 150 amps alternators.
- WB15-55 - POWER TRAIN:AXLE ASSEMBLY: On the vehicles affected by this bulletin, inspect the gap between the radius rod support and the front axle. A deviation in the axle beam envelope can lead to interference between the two parts. In most cases, slightly moving the support w
- SP16-302 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, replace the pressure cap on the surge tank.
- WB16-04 - STEERING: On the vehicles affected by this bulletin the steering damping cylinder rod end spherical bearing may be loose in its housing. Replace as required and secure the steering damper spherical bearing with the provided hardware.
- MI16-05 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information shares information about the bendix m-32qr valve replaced by m-40qr model htat need to be taken into consideration, specially when switching them for the first time on a vehicle.
- Sp17-313 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, replace the batteries by a new set (4) of the same model; perform several verifications on the alternator and charging circuit. Finally, update the multiplex software to the latest version.
- CK17-19A - EQUIPMENT: This conversion kit explains how to remove tgw1 from vehicles using tech tool, no manual vda changes needed. This conversion kit will work for any vehicle equipped with tgw1 up to the vin's listed on the bulletin.
- SP15-341C - ELECTRICAL SYSTEM:HORN: On the vehicles affected by this bulletin, replace the horn support by 140034.
- WB15-19E - EQUIPMENT: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
- SP15-324E - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and r
- SP16-311G - EQUIPMENT: On the vehicles affected by this bulletin, add z clips to secure the direct light lenses, 13 lenses per vehicle.
- Wb17-14A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: On the vehicles affected by this bulletin, the power cable stud adapter on the alternator must be inspected and if needed, replaced.
- IS-15003D - ENGINE (PWS): This insruction sheet explains how to insall the bosch hd10 24v-150a alternator conversion kit ? Twin bosch mounted on volvo d13 engine
- Wb17-10A - WHEELS:LUGS/NUTS/BOLTS: On the vehicles affected by this bulletin, inspect and re-torque the prevost slide-out rail bolts. If damaged, replace bolts.
- sp17-310 - STRUCTURE:BODY:DOOR : On the vehicles affected by this bulletin, it is necessary to replace the two engine door latch pins and the compressor door latch pin by new units made of sturdier material.
- Sp17-312 - STRUCTURE:BODY:DOOR : On the vehicles affected by this bulletin, bus washing operations can result in water dripping into the front service compartment. Add a drip guard above the entrance door valve.
- Sp17-311 - STRUCTURE:BODY:DOOR : On the vehicles affected by this bulletin, replace connector c12 installed inside the dpf access door with an improved version providing a better seal.
- WB16-02C - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system. The corrective measures of this bulletin are very important and must all be ca
- MI16-10A - WHEELS: This maintenance information applies only to vehicles equipped with 19000 lb independent front suspension (ifs) and 22.5 x 10.5 alcoa aluminum wheels for 365/70 r 22.5 size tires. When balancing this wheel for installation on the ifs, a spe
- SP14-323 - SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES: On the vehicles affected by this bulletin, replace the brake pedal assembly.
- SP14-335 - POWER TRAIN:AXLE ASSEMBLY: On the vehicles affected by this bulletin, add a support on the curbside of the drive axle.
- SP14-334 - STRUCTURE: On the vehicles affected by this bulletin, install a lanyard on each of the two overhead access panels in the front section of the bus interior.
- SP14-332 - POWER TRAIN:AUTOMATIC TRANSMISSION: On the vehicles affected by this bulletin, inspect the transmission oil cooler to make sure it is properly secured. In certain material conditions, the bolts may extend beyond the threaded length of the mounting holes in the cooler creating
- SP14-331A - ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS: On the vehicles affected by this bulletin, replace the various bus bars and place one insulation sheet beside the breaker plate
- SP14-330 - LIGHTING (PWS): On the vehicles affected by this bulletin, replace the imron painted marker light guards with powder coated marker lights.
- SP14-324B - STRUCTURE:BODY:BUMPERS: On the vehicles affected by this bulletin, replace the front bumper retaining spring.
- SP14-326 - ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS: On the vehicles affected by this bulletin, the compressor belt may not be tensioned properly since the reduction of the diameter of the pulley on the commuters.
- WB14-47B - ENGINE AND ENGINE COOLING:COOLING SYSTEM: On the vehicles affected by this bulletin, perform a software update of ecm (engine control module) and acm (aftertreatment control module) to provide improved temperature-related behaviour. The software will also change urea dosing valve b
- IS-13169 - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: This instruction sheet explains how to install the aware adaptive cruise braking (acb) flr20 radar sensor replacement kits # 145372 and 145373
- SP14-46 - ELECTRICAL SYSTEM: This bulletin is performed on a fix as fail basis. On the vehicles affected by this bulletin, update to the latest configuration of wiring and sensors for the bitzer compressor.
- WB14-44B - EQUIPMENT:ELECTRICAL: On the vehicles affected by this bulletin, changing of vecu (vehicle electronic control unit) parameters is necessary. This update must be carried out by qualified technicians. Make an appointment with your nearest prevost service center.
- WB14-42A - STEERING: On the vehicles affected by this bulletin, perform a power source improvement and a multiplex software update for the steering gateway module. On a limited number of vehicles, the module will be replaced with the latest version of the part.
- Sp16-320 - STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS: On the vehicles affected by this bulletin, the compressor door support to the vehicle must be improved by the addition of a lower support bracket and the replacement of the two door hinges. A support plate must also be riveted to the door
- WB16-02E - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system.
- MI16-17E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternator.
- Sp16-326B - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: On the vehicles affected by this bulletin, re-torque the clamps on specific coolant hoses of the cooling system.
- IS-15003C - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
- SP16-314 - VISIBILITY: On the vehicles affected by this bulletin, add dampers to the driver's sunshades guides to ease the end course on sunshade retract.
Known Recall Investigations
Alternator front bearing failure investigation # PE21011
Nhtsas office of defects investigation (odi) is opening a preliminary evaluation after receiving a tip from a fleet safety manager concerning alternator front bearing failures that cause elevated temperatures within the engine compartment, resulting in the fire suppression system (fss) activating, immediately shutting the engine down, and rendering the bus inoperable. Review of early warning reporting data identified 9 field reports for model year (my)2015 through my2019 h3 and x3 prevost buses, describing alternator failures in any of 3 alternators equipped on the bus. In some cases, a minor fire occurred damaging nearby electrical harnesses. An immediate shut down of the bus can increase the risk of a crash or injury of passengers when transferring to another bus.Odi is opening this investigation to evaluate the cause, consequence, scope and frequency of the alleged defect in the subject prevost buses.