2007 VOLVO VTVolvo Vt 2007

Complaint Information: Recalls, Investigations, Consumer Complaints, Service Bulletins, Recall Investigations, OBD II Codes

NHTSA Mandated Recalls
  • Recall 97111 [USA]: Without a signal to disengage the clutch when the brakes are applied, the distance required to stop the truck may lengthen, increasing the risk of a crash.
    Volvo trucks north america (volvo) is recalling certain model year 2007-2014 vah, vhd, vnl, vnm, and vt models. The affected vehicles were built without a redundant clutch disengagement switch. Without a redundant switch, a loss of signal from the brake air pressure switch can prevent the clutch from automatically disengaging when the brake is applied.
    volvo trucks will notify owners and dealers will inspect and repair the vehicles if necessary. The recall began on august 26, 2013. Volvo's recall number is rvxx1303. Owners may contact volvo at 1-336-393-2000.
    owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  • Recall 70446 [USA]: Corrosion of the valve can cause it to malfunction, thereby adversely affecting braking performance and increasing the risk of a crash.
    Volvo trucks is recalling certain model year 2007 and 2009 vhd, model year 2006 through 2010 vn, and model year 2007 through 2009 vt trucks manufactured from november 7, 2005, through october 30, 2009, equipped with an air release fifth wheel. The inversion valve on the frame may be orientated where contaminants can enter the valve through the exhaust port. As a result, the brake valve may corrode.
    dealers will inspect the inversion valve and replace as required. This service will be performed free of charge. The safety recall is expected to begin on or before february 18, 2011. Owners may contact volvo trucks at 1-800-528-6586.
    volvo trucks safety recall no. Rvxx1006.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  • Recall 67648 [USA]: If this happens a short circuit may occur, which over time could possibly lead to a vehicle fire.
    Volvo trucks is recalling 127,764 my 2001-2008 vhd, vnl, vnm, and my 2005-2008 vt trucks. A seal may fail allowing water and contaminants to seep into the windshield wiper motor.
    volvo will replace the wiper motor free of charge. Since this recall involves a large number of vehicles, volvo will release the recall in stages as parts are received. Priority will be given to the vehicles located in the regions/states that have a corrosive environment. The recall began on september 30, 2009. Owners may contact volvo trucks at 1-800-528-6586.
    volvo trucks recall no. Rvxx0902.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  • Recall 74785 [USA]: If a short circuit occurs and is left untreated, components and wiring may be subject to overheating which could possibly result in a vehicle fire.
    On certain heavy duty trucks, the circuit protection (i.E. Automatic circuit breakers) used to protect the vehicle lighting system may not provide adequate protection.
    dealers will replace the circuit breakers with fuses. The recall began on february 25, 2008. Owners may contact volvo trucks at 1-800-528-6586.
    volvo trucks recall no. Rvxx0707.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  • Recall 71843 [USA]: There is a possibility that the pivot bolt can become loose without the driver's knowledge. when this occurs, the driver could drive away and the trailer could become disengaged, increasing the risk of a crash.
    On certain trucks equipped with a saf holland simplex fifth wheel, the lever arm pivot bolt may have been over tightened. An over tightened pivot bolt can distort the pivot bolt spacer sleeve, which may prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin.
    dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer free of charge. The recall began on january 28, 2008. Owners may contact volvo trucks at 1-800-528-6586.
    volvo trucks recall no. Rvxx0705.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  • Recall 88913 [USA]: If the condition exists and the key is left on without fuel in the filter, the heating element may heat to a point where a flame becomes present at the tip of the element which could result in a vehicle fire.
    On certain trucks, an unprotected lead in the thermoswitch of the heater may make contact with another post possibly creating a short circuit, which can result in continuous operation of the heating element.
    dealers will inspect the thermoswitch and will replace it if necessary. The recall began on september 10, 2007. Owners may contact volvo trucks at 1-800-528-6586.
    volvo truck recall no. Rvxx0703.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  • Recall 32194 [USA]: If the nut were to come loose, the steering shaft could potentially separate resulting in loss of steering control which could cause a crash.
    On certain trucks, the nut used to retain the steering shaft may or may not be a lock nut that has the locking feature. A lock nut is required to provide additional resistance to ensure that the nut does not come loose.
    dealers will replace the steering shaft pinch bolts and locknuts free of charge. The recall began on august 24, 2007. Owners may contact volvo trucks at 1-800-528-6586.
    volvo recall no. Rvxx0702.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  • Recall 37006 [USA]: This could result in additional damage to the driveline, the vehicle to which it is attached and ay additional nearby objects.
    On certain trucks equipped with arvinmeritor rpl20 high angle interaxle driveshafts, an improper seated or missing snap ring can result in the bearing cup to separate from the slip yoke sub-assembly. The universal joint cross could then contact the slip yoke casting and eventually cause the ear work to fracture.
    dealers will inspect the driveshafts and replace them as needed. The recall began on october 23, 2006. Owners may contact volvo trucks at 1-800-528-6586.
    volvo truck recall no. Rvxx0605.Customers can also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  • Recall 51323 [USA]: This could potentially lead to steering shaft separation resulting in loss of control of the vehicle if the pinch bolt were to come loose increasing the risk of a crash.
    On certain heavy duty class 8 trucks equipped with dana steering shafts, there is a potential that the steering shaft pinch bolt hole may be incorrectly located. The pinch bolt fits into a groove in the steering gear input shaft to ensure that the steering shaft does not separate from the steering gear if the pinch bolt comes loose.
    dealers will inspect the steering shaft and replace it as required free of charge. The recall began on august 28, 006. Owners may contact volvo trucks at 1-800-528-6586.
    volvo trucks recall no. Rvxx0602.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  • Recall 2013221 [Canada]: Other
    On certain vehicles, the secondary clutch disengagement switch may have been omitted during vehicle assembly or, in some instances, removed during servicing. As such, primary switch failure would cause the automated manual transmission’s clutch to remain engaged when the brakes are applied. This could increase stopping distances, possibly resulting in a crash causing property damage and/or personal injury. Correction: dealers will install a micro-switch at the brake pedal and update the software to run a diagnostic on the switch during engine start-up.

  • Recall 2010433 [Canada]: Other
    On certain trucks equipped with an air release fifth wheel hitch, the inversion valve on the frame may be orientated where contaminants can enter the valve through the exhaust port. As a result, the brake valve may corrode causing it to malfunction and in some cases result in unintended opening of the fifth wheel's locking mechanism. This could allow the trailer to separate from the towing vehicle while underway. Also, an air loss could increase vehicle stopping distance and result in a crash causing property damage or personal injury. Correction: dealers will inspect and replace the inversion valve if required.

  • Recall 2009144 [Canada]: Other
    On certain vehicles, the windshield wiper motor may be susceptible to water intrusion, which could result in an electrical short circuit and a fire. This could cause property damage, personal injury or death. Correction: dealers will affect repairs.

  • Recall 2007253 [Canada]: Steering
    On certain trucks, the locknut used to retain the steering shaft may not have had the lock feature. As a result, the nut could loosen, allowing the steering shaft to separate, causing a loss of steering control which could result in a vehicle crash with injury or death. Correction: dealers will replace the steering shaft pinch bolt and locknut.

  • Recall 2007257 [Canada]: Fuel supply
    On certain trucks, when the ignition key is in the 'on' position, the pre-heater, located in the fuel filter base, is energized. If this pre-heater is energized while maintenance is being performed on the fuel filter, diesel fuel could ignite within the filter housing. A fire within the fuel filter housing may spread possibly resulting in property damage or personal injury. Correction: dealers will inspect and, if required, replace the fuel heater assembly.

  • Recall 2007338 [Canada]: Other
    On certain trucks, the fifth wheel hitch assembly's lever arm may have been incorrectly installed during the manufacturing process. The lever arm pivot bolt may have been over-tightened which could distort the pivot bolt spacer sleeve and prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin. This could allow the towed unit to separate from the towing vehicle while underway, potentially causing a crash with injury or death. Correction: dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer.

  • Recall 2007394 [Canada]: Electrical
    On certain trucks, the automatic circuit breakers used to protect the vehicle lighting system may not provide adequate protection. If a short circuit occurs, components and wiring may be subject to overheating, which could result in a vehicle fire, causing property damage and/or personal injury or death. Correction: dealers will replace the circuit breakers with fuses.

  • Recall 2006072 [Canada]: Steering
    On certain vehicles, the steering shaft pinch bolt hole may be incorrectly located. As a result, the steering shaft may separate from the steering gear which could lead to a sudden loss of vehicle control and a crash. Correction: dealers will inspect and, if required, replace the steering shaft.

  • Recall 2006243 [Canada]: Powertrain
    On certain trucks, an improperly seated or missing u-joint snap ring can result in the bearing cup to separate from the slip yoke sub-assembly. The u-joint could then contact the slip yoke casting and eventually cause the ear to fracture. This could result in additional damage to the driveline, the vehicle and any nearby objects. Correction: dealers will inspect and, if required, replace the driveshafts.

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • KC-202 - POWER TRAIN: Cbr - automated manual transmission ( amt ) flywheel pilot bearing wear on input shaft.
  • KC-183 - POWER TRAIN: Volvo chassis - ( amt, i-shift ) - transmission grinding when downshifting ; range synchronizer (synchro) timing procedure - us07 and newer
  • V-265-002 - ENGINE AND ENGINE COOLING: Tsb-charge air cooler t-clamp install.
  • CBR-2201 - ENGINE AND ENGINE COOLING: Engine control module (ems) software (msw) information a?? August 2022; improvement list (change log) - us21+obd22 (13l vgt, tc) and us17+obd22 (11l) emissions
  • KC-435 - POWER TRAIN: Volvo chassis - equipped with an automated manual transmission (amt, ishift) - snv 19-002 - amt oil filter housing corrosion
  • KC-2174 - SUSPENSION: Volvo chassis - drag link inspection and replacement criteria
  • KC-2028 - POWER TRAIN: Amt control housing bench testing - false failures
  • KC-2107 - ENGINE AND ENGINE COOLING: Def level (uqls) sensor troubleshooting guide - us17+obd16 emissions and newer
  • KC-2112 - POWER TRAIN: Programming failure - chassis with cummins engine and an allison transmission
  • KC-2116 - ENGINE AND ENGINE COOLING: Nox sensor troubleshooting guide - us10+obd13 and newer emissions
  • KC-2119 - SERVICE BRAKES, AIR: Dtc U012100 - lost communication with anti-lock brake system (abs) control module, no additional information
  • KC-2143 - VEHICLE SPEED CONTROL: (back office) - cruise control inoperative after updating software vecu5 without esp package (uesp)
  • KC-2165 - ENGINE AND ENGINE COOLING: Def pump troubleshooting guide - us10+obd13 and newer emissions
  • KC-2171 - ENGINE AND ENGINE COOLING: Temperature sensor troubleshooting guide - us10+obd13 and newer
  • KC-405 - POWER TRAIN: Warranty automated manual transmission ( amt, i-shift, mdrive ) control housing assembly; guidelines for filing a claim for chassis return visit with transmission issues after a repair requiring control housing removal and reinstallation -
  • KC-732 - EQUIPMENT: Unable to retrieve "on request" messages for peoplenet or omnitracs modules installed on the dl5 data link; third party electronic log device not reporting certain data
  • KC-682 - ELECTRICAL SYSTEM: Sensor and parameter values missing or reading zero when performing a sensor and parameter values monitor with premium tech tool ( ptt ) - us07 and us10 ( pre-obdii, 9-pin diagnostic connector ) chassis
  • KC-2107 - ENGINE AND ENGINE COOLING: Def level (uqls) sensor troubleshooting guide - us17+obd16 emissions and newer
  • KC-726 - ELECTRICAL SYSTEM: Fuel level gauge reading incorrect in the instrument cluster
  • SNV22-003 - UNKNOWN OR OTHER: The diagnostic process
  • KC-623 - POWER TRAIN:AUTOMATIC TRANSMISSION: Volvo i-shift amt will not calibrate after incorrect flywheel housing is installed
  • KC-636 - ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION MOTOR:CONTROLLER:SOFTWARE: Volvo fault code mid 144 psid 204 fmi 9
  • KC-639 - ELECTRICAL SYSTEM:SOFTWARE: Volvo snv15-008 vocom adapter ( 88890300 ) may lock up when updating firmware
  • KC-640 - UNKNOWN OR OTHER: Volvo chassis - dealer support communication - selecting the proper sr area for creating an eservice
  • KC-642 - ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE: Volvo chassis - bendix abs6 to abs8 service information
  • KC-647 - UNKNOWN OR OTHER: Volvo chassis ghost codes due to poor grounding
  • KC-649 - UNKNOWN OR OTHER: Volvo snv14-035 when and how to contact tech support ( eservice & phone )
  • KC-650 - ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE:FUEL LEVEL FLOAT/SENSOR/SENDING UNIT: Volvo chassis - fuel level gauge slow to respond to changes in fuel level
  • KC-660 - UNKNOWN OR OTHER: Volvo chassis - pto pump speed calculator
  • KC-674 - ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE:FUEL LEVEL FLOAT/SENSOR/SENDING UNIT: Volvo chassis - fuel level sending unit specification information
  • KC-675 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: (back office only) volvo chassis - equipped with a catalyzed exhaust aftertreatment system ( eats ) - regeneration ( regen ) failure diagnostic process - us07 to us16 emissions
  • TJ 35503 - EQUIPMENT: Panoramic sunroof, sealing strip has a gap
  • Service Manager - EQUIPMENT: Shipping and handling of volvo lithium-ion 48v mild hybrid battery to global battery solutions (gbs)
  • 356EN01 - EQUIPMENT: Vida qr scanner mobile app
  • KC-784 - ELECTRICAL SYSTEM:SOFTWARE: Volvo chassis - diagnostic trouble code ( dtc ) P0420 illuminating the malfunction indicator lamp (mil)
  • KC-705 - POWER TRAIN: Volvo chassis - diagnostic trouble codes ( dtc's ) - mid130 pid160 fmi1 or fmi2 - for the i-shift transmission
  • KC-675 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: (back office only) volvo chassis - equipped with a catalyzed exhaust aftertreatment system ( eats ) - regeneration ( regen ) failure diagnostic process - us07 to us16 emissions
  • KC-541 - SUSPENSION: Volvo chassis - fsb 761-002, shock absorber, inspection
  • KC-395 - ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL: Instrument cluster programming - programming fails or errors display when replacing an instrument cluster with a newer part number (conversion kit) - us04 to us10 chassis (9-pin diagnostic connector)
  • KC-392 - POWER TRAIN:DRIVELINE:DRIVESHAFT: Volvo chassis - driveline (driveshaft, propeller shaft) ride height and angle, measurement and calculation; pinion angle measurement - model year 1996 and newer
  • KC-357 - FUEL SYSTEM, OTHER:KINETIC:FLYWHEEL,BEARINGS: Volvo chassis - equipped with an i-shift automated manual transmission ( amt ) - flywheel resurfacing and reuse guidelines
  • KC-304 - ENGINE AND ENGINE COOLING: Cylinder head reuse and replacement guidelines - inspection and information - us04 and newer emissions, commonly 2007 and newer model years
  • K41105570 - ELECTRICAL SYSTEM: Instrument cluster programming - programming fails or errors display when replacing an instrument cluster with a newer part number (conversion kit) - us04 to us10 chassis (9-pin diagnostic connector)
  • K15812145 - ENGINE AND ENGINE COOLING: Volvo chassis - snv 15-016 documented process for engine oil consumption - all emissions, all model years
  • K52326370 - FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:FUEL RAIL: Volvo chassis - diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair - us10 to us14 ( non-common rail fuel system ) removed information for common rail chassis - now has its own solution.
  • FSB216-002 - ENGINE (PWS): Flywheel resurfacing guidelines, i-shift
  • FSB 216-001 - EQUIPMENT: Twin mass flywheel conversion
  • FSB 593-012 - ELECTRICAL SYSTEM:STARTER ASSEMBLY:SOLENOID: Hill start assist solenoid, replacement
  • FSB 293-024 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE): Exhaust gas recirculation (egr) differential pressure sensor
  • FSB 234-019 - FUEL SYSTEM, DIESEL: Dual fuel tanks ventilation filter kit
  • FSB 234-018 - FUEL SYSTEM, GASOLINE: Single fuel tank ventilation filter kit
  • FSB 593-012 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Hill start assist solenoid, replacement
  • FSB 801-003 - STRUCTURE:BODY:DOOR : Service door rust prevention
  • FSB 432-013 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Amt high range cone replacement
  • FSB 593-012 - ELECTRICAL SYSTEM:STARTER ASSEMBLY:SOLENOID: Hill start assist solenoid, replacement
  • FSB 215-002 - EQUIPMENT:MECHANICAL: Timing plate leak repair
  • FSB 284-038 - ELECTRICAL SYSTEM:SOFTWARE: Engine coolant thermostat software update
  • FSB 811-006 - EQUIPMENT: Floor cracks repair (rear panel)
  • FSB 811-005 - EQUIPMENT: Floor cracks repair (front panel)
  • FSB 431-010 - EQUIPMENT: Range synchronizer, repair
  • FSB 216-001 - POWER TRAIN: Twin mass flywheel conversion, transmission removed
  • FSB 593-012 - ELECTRICAL SYSTEM:STARTER ASSEMBLY:SOLENOID: Hill start assist solenoid, replacement
  • FSB 432-014 - POWER TRAIN:AUTOMATIC TRANSMISSION: Transmission ecu compatibility
  • FSB 284-047 - ELECTRICAL SYSTEM:WIRING: Oil level sensor harness wire splice
  • FSB 210-001 - EQUIPMENT:OTHER:LABELS: Engine data label
  • FSB 213-002, Exh - EQUIPMENT ADAPTIVE/MOBILITY: In some instances the exhaust rocker piston cap screw may become loose and back out causing loss of engine compression, or a mechanical injector diagnostic trouble code (dtc).
  • FSB-432-013 - POWER TRAIN:AUTOMATIC TRANSMISSION: Volvo truck: procedural information regarding the replacement of high range cone in the section of the automated manual transmission (amt). Model vn, vhd, vah, vt. *pe updated 8/8/14. *pe
  • FSB-221-011 - ENGINE (PWS): Volvo: low oil pressure, on certain vehicles, during long hard pull conditions, diagnostic trouble codes (dtcs) pid 100 fm1, spn 100 fmi 1 or P252400, can log on, with or without engine shut down lamp. Model vn, vt. No years listed. *pe
  • FSB-284-047 - ELECTRICAL SYSTEM:WIRING: Volvo: on some trucks, there is an oil contamination into the engine wire harness because of a failure of the oil level sensor. Models vah, vhd, vn, vt. No model years listed. *pe
  • FSB-375-008 - SEATS: Volvo trucks: during operation of driver side swivel seat and i shift transmission, the harness rubbing or wires, are pulled out of connectors. This causes seat harness dropping or pulling away from clipping points. *pe
  • FSB-357-002 - INTERIOR LIGHTING: Volvo: light control module (lcm), reprogramming. On some volvo units equipped with clear led clearance lights in the sun visor, the may exhibit an active fault code mid 216 psid 49 fmi 5. This fault indicates a trailer marker open issue wh
  • FSB-255-023 - ENGINE AND ENGINE COOLING:ENGINE: Volvo trucks: connector pin, replacement. Severe fretting damage of the engine variable geometry turbocharger actuator (engine vgt actuator) harness and turbine shaft speed sensor (tss) connector may cause an unreliable signal to the engin
  • FSB-371-040 - ELECTRICAL SYSTEM:WIRING: Volvo: the front chassis harness may have been routed with the compressor air discharge line which can lead to corrosion of the harness. *rm
  • FSB-844-002 - VISIBILITY:GLASS, SIDE/REAR: Volvo: there may be leaks at the lower sleeper window. *rm
  • SP-252-025 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Volvo: an exhaust pipe insulation blanket can deteriorate over time. A new blanket has been released to protect from road splash. *rm updated 9/12/11. *pe
  • SP-252-024 - STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS: Volvo: an exhaust pipe insulation blanket can deteriorate over time. A new blanket has been released to protect from road splash. *rm updated 9/12/11. *pe
  • SB-410-01 - POWER TRAIN:AUTOMATIC TRANSMISSION: Volvo: there are new clutch bearing lubrication tubes. *rm
  • FSB-357-001 - EXTERIOR LIGHTING:HEADLIGHTS:SWITCH: Mack trucks: there is revised mounting hardware for the exhaust manifold and turbocharger. *rm
  • FSB-234-009 - FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY:MOUNTING: Volvo truck: fuel tank mounting. Fuel tank straps over time may lose torque and allow the fuel tank to rotate. Models vn, vhd, vt, vah. No model years listed. *pe updated 2/21/12. *pe
  • FSB-845-001 - STRUCTURE:BODY:DOOR : Volvo truck: door seal, outer, replacement. The outer seal on the cab doors of volvo model trucks may prematurely separate from the cab shell. Models vn-2, vhd-2 and vt. No model years listed. *pe
  • FSB-431-001 - POWER TRAIN:AUTOMATIC TRANSMISSION: Volvo truck: i shift transmission with mixed components. Installation of replacement parts in an i shift transmission (version-c) may result in diagnostic trouble codes (dtcs) mid 130 pid 160 fmi1 or fmi2. No model years listed. *pe
  • FSB-252-023 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Volvo trucks: exhaust flex pipe cracks. Beginning may 12, 2008, a redesigned exhaust flex pipe and turbocharger outlet pipe (located between the turbocharger diffuser pipe and the exhaust flex pipe) were implemented into production on vn,
  • SB-252-022 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Volvo trucks: exhaust flex pipe relocation. Certain cab model trucks may experience a deformation of the right hand cab skirt due the close proximity of the exhaust flex pipe. To resolve this issue a new intermediate pipe has been releas
  • SB-824-002 - STRUCTURE:FRAME AND MEMBERS: Volvo truck: to reduce the potential for cab water intrusion, a cab cowl seal has been released by engineering. The seal part number 8083305 is positioned above the top edge of the cowl panel to divert water flow onto the cowl panel rathe
  • SB-261-017 - FUEL SYSTEM, DIESEL: Volvo truck: on some vehicles, coolant overflow out of the overflow tube occurs during the diesel particulate filter regeneration cycle. Excessive coolant flow from the radiator top tank and thermostat vent lines prevents flow into the de-a
  • SB-364-025 - POWER TRAIN:CLUTCH ASSEMBLY: Volvo truck; clutch switch clip; it has been found that vn, vhd and vt vehicles use a spring clip to retain the clutch switch, may have an issue with the clutch switch moving or detaching from it's mount. *pe
  • RTJ-16629 - ELECTRICAL SYSTEM:SOFTWARE: Volvo: leakage detection diagnostics improvements to remedy dtc's. All models from model years 2003-2008. Diagnostic monitor for the evaporative emission system small leak, has used a software function that calculates leakage based on a pr
  • FSB-873-014 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Volvo truck: reports prompted the release of a replacement connector for the cab hvac motor resistor. Replacement connector is supplied as kit part, which contains the connector body and the necessary terminals. Model years unknown.
  • FSB-372-005 - UNKNOWN OR OTHER: Volvo trucks: mega fuse corrosion. Volvo vehicles with us 07 emissions compliant engines built between 11/12/06 and 12/05/08 may have corrosion issues with the two mega fuses in the battery box area. *pe
  • SP-372-008 - EQUIPMENT ADAPTIVE/MOBILITY: Volvo trucks: mega fuse corrosion. Emissions complaint engines built between 11/13/06 and 12/05/08 may have corrosion issues with the two mega fuses in the battery box area. *pe
  • SP-372-007 - ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS: Volvo trucks: mega fuse breaking. Trucks with us 07 emissions compliant engines built between 6/30/06 and 1/15/08 may experience an issue with the battery compartment mounted 150 amp positive side mega fuse breaking. Models vn, vhd, and vt.
  • 373-006 - POWER TRAIN:AUTOMATIC TRANSMISSION: Transmission ecu fuse contamination for certain volvo vehicles - vn-2, vhd-2, vt. *pe
  • 372-007 - ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS: Mega fuse breaking on volvo vehicles - vn, vhd, vt. *pe
  • 371-030 - ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES: Battery cable routing for certain volvo vehicles - vn-2, vhd-2, vt. *pe
  • 432 025 - POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL): Sp 432-025, control unit, gear selector replacement; at2512c, ato2512c, at2812c, ato3112c. *pe
  • SP764-005 - UNKNOWN OR OTHER: Sp 764-005, load leveling valve, replacement -- certain vn-2, vhd-2, and vt model trucks built between 9/1/06 and 4/1/07 with rear air suspension need to have the rear suspension leveling valve replaced. *nj
  • SP258-003 - UNKNOWN OR OTHER: Dpf replacement -- certain volvo vehicles built between 7/1/06 and 7/22/07 with a vertical back of cab (vboc) diesel particulate filter (dpf) and a stack height of 3.8 meters (12' 6") or greater, may experience cracking of the dpf outlet
  • SP 258-003 - UNKNOWN OR OTHER: Sp 258-003, diesel particulate filter outlet module, replacement. Certain volvo vehicles built between 07/01/06 and 07/22/07. *nj
  • 764005 - SUSPENSION:REAR:SPRINGS:AIR SUSPENSION SYSTEM: Certain vn-2, vhd-2, and vt model trucks built between 9/1/06 and 4/1/07 with rear air suspension need to have the rear suspension leveling valve replaced. *nj updated 3/17/08. *nj
  • 366002 - ENGINE AND ENGINE COOLING:COOLING SYSTEM: Volvo trucks north america - sp 366-002, active pressure coolant system module failure / built with a d16d engine between 01/10/05 and 02/27/07. *nj
  • 00211 - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: New technical courses available. Introduction to tire pressure monitoring systems - classes now available. This course is intended to familiarize technicians and workshop foremen with volvo's tire pressure monitoring systems. *nj
  • 017 - ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL: Instrument cluster reprogramming. *tt
  • 018 - ENGINE AND ENGINE COOLING:COOLING SYSTEM: Cooling system update, us vehicles only. Replacement of the coolant expansion tank, expansion tank right hand support bracket, and the upper radiator hose. *tt
Known Recall Investigations
  • Stop lamp switch signal investigation as of 20130207

    The office of defects investigation (odi) received early warning reporting (ewr) data from the manufacturer that indicated some number of subject vehicles equipped with the subject automated manual transmission had allegedly experienced a condition where the clutch failed to automatically disengage the transmission from the engine as intended. This may result in extended stopping distances and/or unintended forward motion of a vehicle previously at rest.To date, odi is aware of 134 subject vehicles with one or more complaints or field reports related to this condition.Also, odi is aware of 164 subject vehicles with one or more warranty claims related to this condition.By letter dated june 25, 2013, volvo trucks north america (volvo) notified odi that it has initiated a safety recall (nhtsa recall no. 13v268 and volvo recall no. Rvxx1303) to address a safety defect in approximately 23,003 model year (my) 2007 through 2014 volvo vah, vhd, vnl, vnm and vt model trucks. The affected vehicles were manufactured from december 20, 2006 through may 22, 2013 and were originally equipped with the subject automated manual transmissions.According to volvo, reports of the subject transmission clutch mechanism failing to automatically disengage as intended are associated with the removal of a brake pedal micro switch that provided a redundant signal to the transmission control module indicating the brakes had been applied.Previously, volvo had removed this brake pedal micro switch from new vehicle production and from certain vehicles already in-service via two field service campaigns (sp 432-024 and sp 432-026) because it decided the switch was unnecessary and/or a maintenance issue.In the absence of this redundant brake pedal micro switch, the clutch mechanism may fail to disengage the transmission from the engine at low vehicle speed should the stop lamp switch fail to send and/or the transmission control module fail to receive the primary signal.At the time of this closing, volvo is evaluating available remedies and will provide nhtsa with details when the recall remedy procedure has been finalized.Volvo will notify affected owners by mail by august 25, 2013.Please see nhtsa recall no. 13v268 for details.Accordingly, this investigation is closed.

  • Volvo sleeper glass de-bonding investigation as of 20110523

    Odi opened recall query rq11-001 after a review of ewr field reports identified lower bunk window separations on the subject vehicles.Volvo had issued three recalls for sleeper window separations since 2003.Additionally, volvo had issued two bulletins for sleeper window issues during the same time period.The frequency of related actions led odi to open this formal investigation.An information request (ir) letter was sent to volvo on 23 june 2011.Volvo responded on 17 august 2011 and then provided updated warranty information on 9 january 2012.Volvo provided production change data and warranty information which was correlated to vehicle build month and failure date.Odi analyzed the data to determine if additional production time frames should have been included in previous recalls.Odi also requested information from its network of fleet owners.The response from this network reaffirmed the accuracy of the updated warranty information.Based on the information and data received, odi has concluded that all production periods have been appropriately addressed by volvos previous recalls and no additional recall action is required at this time.

  • Saf holland fifth wheel assembly investigation as of 20070914

    On october 18, 2007 volvo trucks north america filed defect report 07v-496 which outlines a safety recall program to notify the affected owners and correct the affected vehicles.

OBD-II Error Codes

Common OBD Error codes specific to this vehicle.

  • U0121 [1] Lost Communication With Anti-Lock Brake System (ABS) Control Module
  • P0420 [1] Catalyst System Efficiency Below Threshold (Bank 1)
  • P2524 [1] A/C Request "B" Circuit High
Most Recent Consumer Complaints and Accidents
CrashFireTowedInjuredDeathsFailure
Date
NoNoN NoneNone20090212

2007 volvo vt, drivers side window shattered. *bf ohio traffic crash report # 10-0293-91 updated 05/03/10 *bf

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.