Prevost X3-45 Commuter 2012

Vehicle Details: Recalls, Investigations, Service Bulletins

Below you will find all available information on the 2012 PREVOST X3-45 Commuter.

ManufacturerKnown WMI(s)Fuel Type
PREVOST
PREVOST VIN Decoder

Use the box here to look up VINs from PREVOST as well as other manufacturers

#
Frequently Asked Questions
  • Are there recalls for the 2012 PREVOST X3-45 Commuter?
     - There are 17 recall(s) for the 2012 PREVOST X3-45 Commuter, additional information is below.
NHTSA Mandated Recalls
  • Recall 260230 [USA]: Beacons that do not provide proper illumination may be less visible to wheelchair lift users, increasing the risk of injury.

  • Recall 193098 [USA]: An overheated alternator bearing can increase the risk of a fire.

  • Recall 138429 [USA]: A complete loss of steering would increase the risk of a crash.

  • Recall 133675 [USA]: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.

  • Recall 138338 [USA]: If the fuel tank separates from the vehicle, it could be a road hazard and the vehicle would stall. either scenario increases the risk of a crash.

  • Recall 114515 [USA]: The damaged wires may activate the afss and shutdown the engine, increasing the risk of a vehicle crash.

  • Recall 108583 [USA]: The fuel line rubbing may result in abrasion and a fuel leak, increasing the risk of a fire.

  • Recall 103628 [USA]: A damaged seat belt may fail in the event of a crash, increasing the risk of injury to the seat occupant.

  • Recall 101693 [USA]: If the afss tank discharges and there is a vehicle fire, the automatic fire suppression system will be unavailable to assist in extinguishing the vehicle fire, increasing the risk of injury.

  • Recall 100617 [USA]: Without functioning windshield wipers, the driver's visibility may be reduced, increasing the risk of a crash.

  • Recall 93743 [USA]: Uncontrollable throttle position may lead to a loss of vehicle control, increasing the risk of a crash.

  • Recall 95644 [USA]: An activation of the afss causes the vehicle to come to an unplanned stop. this could increase the risk of a vehicle crash or personal injury.

  • Recall 94792 [USA]: If the rod breaks while the vehicle is in use, stability and vehicle control may be lost, increasing the risk of a crash.

  • Recall 90782 [USA]: If the event of a fire, the afss may not operate as designed, increasing the risk of injury to the coach occupants.

  • Recall 93220 [USA]: If the power cables short-circuit, a vehicle fire may result.

  • Recall 90941 [USA]: If this occurs, a short-circuit, or fire may result, increasing the risk of personal injury.

  • Recall 91612 [USA]: Over time, the steering gearbox bolts may start to loosen, leading to reduced steering function, increasing the risk of a crash.

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • IS-23019 - SUSPENSION: Sway bar collars improvement
  • IS-18106 - STEERING: Kit power steering tank convertion cummins to zf with d13 engine
  • MI16-32 - ENGINE AND ENGINE COOLING: Improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • IS-19912E - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with delco remy alternator. Revision: e note added regarding power cable connection
  • IS-19901E - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with bosch alternator. Revision: e note added regarding power cable connection
  • IS-21072B - ELECTRICAL SYSTEM: Steering gateway. Revision b - pin 2 and 10 were inverted on connector a139
  • MI22-12B - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: b - general update
  • MI22-12A - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: a - erroneous secondary & accessory tanks location.
  • MI22-12 - SERVICE BRAKES, AIR: Air tanks draining sequence
  • IS-17151C - EXTERIOR LIGHTING: Halogen to led fog light replacement kit. Revision: c - advanced kits canceled
  • IS-22902 - WHEELS: Tag axle hub flange - alternate cap screw
  • IS21-072 - ELECTRICAL SYSTEM: Steering gateway, revision a : cancel watch dog removal from efd part of the instruction
  • MI20-08C - EQUIPMENT: Storage and startup guidelines : part number updates
  • IS21-901 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : X3 series envirocare - ions air sanitizer
  • IS21-072A - ELECTRICAL SYSTEM: Steering gateway revision a cancel watch dog removal from efd part of the instruction
  • IS20-925A - VISIBILITY: Central hvac merv filters installation
  • MI18-16B - ELECTRICAL SYSTEM: Bosch hd10 alternator diagnostic guide revision b to avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
  • MI21-06 - FUEL SYSTEM, DIESEL: Diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair ⿿ from us10 to newer engine generation
  • Mi21-07A - WHEELS: Ront & tag axle ⿿ unitized hub bearing end play verification and replacement
  • IS-21901 - EQUIPMENT: X3 series envirocare - ions air sanitizer
  • IS-19912D - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator - x3 series us10 up to ghg17 cooling system
  • IS-19901D - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator
  • IS-18042 - ELECTRICAL SYSTEM: Eberspacher preheater installation in replacement of spheros & valeo preheaters
  • IS-08080B - EQUIPMENT: Sound selector replacement, vss04 to vss05; when replacing a vehicle sound selector model vss04 with a new sound selector model vss05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new
  • IS-19901C - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator - x3 series us10 up to ghg17 cooling system
  • IS-19912C - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator
  • MI20-08C - STRUCTURE: Storage and startup guidelines: periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, prevost recommends foll
  • IS-20925A - POWER TRAIN: Central hvac merv filters installation reva
  • VBC-PREVOST 2 - EQUIPMENT ADAPTIVE/MOBILITY: Bendix m-32qr abs modulator valve replaced by new m-40qr valve.
  • SP21-300 - EQUIPMENT: Automatic fire suppression system - tamper seal replacement
  • IS-18091A - STEERING: Tie rod 610052 first installation instructions: use these instructions when replacing the drop joint tie rod on s82, s84 / s84u i-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment ne
  • MI20-19B - ENGINE AND ENGINE COOLING: Introducing a new engine coolant into prevost service center network
  • MI20-19A - ENGINE AND ENGINE COOLING: Rev a: mention added concerning ddc series 60 engine sca requirement
  • MI21-01 - EQUIPMENT: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI21-01 - POWER TRAIN: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI20-19 - EQUIPMENT: Introducing a new engine coolant into service
  • MI17-03 - ELECTRICAL SYSTEM: After the installation of the latest multiplex system update on us10 x3-series coaches, the instrument panel and switches backlighting may stay constantly on due to an output (j1:4) on the a44 module sending constant current to the 114a cir
  • IS-14145 - ELECTRICAL SYSTEM: This instruction sheet explains how to add sunshade switches on the dashboard
  • MI16-17D - SEATS: Use this procedure for the removal and installation of the twin bosch hd10 (120a or 150a) alternators.
  • MI18-02A - ENGINE AND ENGINE COOLING: Engine oil & filter change intervals - volvo d13 engine, from us10 revision: a updated for obd20 engines
  • MI20-08B - EQUIPMENT: Storage and startup guidelines revision: b parts added to suggested material 08-10-2020
  • IS-20922 - EQUIPMENT ADAPTIVE/MOBILITY: Sigma passenger seats partition kit
  • MI20-12 - STEERING: Jerky, noisy or hard to turn steering gearbox. Hydraulic end limiter adjustment. All models ⿿ equipped with rb bosch/zf servocom or servocomtronic steering gearbox
  • IS-19901B - EQUIPMENT: Electric fan drive cooling system conversion with bosch alternator revision b: parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal, st,16
  • IS-19912B - ENGINE (PWS): Electric fan drive cooling system conversion with delco remy alternator revision : b parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal,
  • IS-20907 - EQUIPMENT ADAPTIVE/MOBILITY: Plexiglass panel behind driver x3
  • MI20-08A - EQUIPMENT: Storage and startup guidelines: rev a: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
  • MI20-09 - EQUIPMENT: Prevost vehicle disinfection procedure revision a
  • P256000 - EQUIPMENT: Repair instructions to address fault codes P256000 engine coolant level low
  • P052400 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P052400 engine oil pressure too low
  • P029800 - ENGINE (PWS): Repair instructions to address fault codes P029800
  • P021700 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P021700 engine coolant over temperature condition
  • NOx_Conv2 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P207F-00; P20EE-00
  • NOX_Conv1 - EQUIPMENT ADAPTIVE/MOBILITY: Repair instructions to address fault codes P207F-00 - reductant quality
  • MI20-09 - EQUIPMENT:OTHER:LABELS: Prevost vehicle disinfection procedure
  • MI20-08 - UNKNOWN OR OTHER: Storage and startup guidelines - all prevost vehicles & volvo 9700
  • IS-20905 - EQUIPMENT: Hand sanitizer dispenser installation
  • IS-19912A - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator - mention added stating to disable ⿿prime⿝; parts added in the kit.
  • IS-19901A - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator - x3 series us10 up to ghg17 cooling system - mention added stating to disable ⿿prime⿝; parts added in the kit
  • MI15-24 - EQUIPMENT ADAPTIVE/MOBILITY: Added: power cables for l.H. Side alternator & fan drive breaker box
  • IS-19901A - ENGINE AND ENGINE COOLING: Revision : mention added stating to disable prime & parts added in the kit.
  • IS-19921A - EQUIPMENT: This instruction sheet explains how to install a seatbelt cutter in the driver's area
  • SCI19-01C - ELECTRICAL SYSTEM: The intent of this procedure is to guide you through the steps required to program a mcm especially for the control of the electric fan drive as required for conversion kit of instruction sheets is-19900, is-19901, is19910, is-19912.
  • IS-19912 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system conversion kit (with delco remy alternators) on x3 vehicles equipped with us10 up to ghg17 engine.
  • IS-19901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system with bosch alternators on x3 series vehicles equipped with us10 up to ghg17 engines
  • IS-17151 - LIGHTING (PWS): This instruction sheet explains how to replace halogen fog light to led's
  • IS-19040A - STEERING: This instruction sheet explains how to replace power steering pump discharge hose (pressure) - #161335p or #160039
  • IS-19912 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system conversion kit (with delco remy alternators) on x3 vehicles equipped with us10 up to ghg17 engine.
  • IS-19901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system with bosch alternators on x3 series vehicles equipped with us10 up to ghg17 engines;
  • IS-18091 - STEERING: This instruction sheet explains how to perform the first installation of tie rod 610052 on prevost vehicles equipped with dana s82, s84 / s84u i-beam axles, 1994- today
  • MI18-45A - POWER TRAIN: Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to is-18091 for installation instruction
  • IS-19922 - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: Prevost aware adaptive cruise braking (acb) flr10 to flr21 radar sensor upgrade
  • IS-19915 - EQUIPMENT: Mp-1000 multimedia player installation
  • IS-19040 - STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS: Power steering pump discharge hose (pressure) replacement
  • IS-18910 - EQUIPMENT: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-18025A - SUSPENSION: This instruction sheet shows how to replace kneeling level sensor #21643575 by sensor #22194741.
  • IS-18025A - SUSPENSION: This instruction sheet shows how to replace kneeling level sensor #21643575 by sensor #22194741.
  • WB19-07 - SERVICE BRAKES, AIR: On the independent front suspension (ifs) of the vehicles affected by this bulletin, check and make sure that there is enough clearance between the brake hoses identified in the procedure and their respective support bracket.
  • IS-19913 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to install delco remy alternators
  • IS-19040 - STEERING: This instruction sheet explains how to perform the replacement of the power steering pump discharge hose (pressure) #161335p or #160039, using kit #160127;
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-19913 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to install delco remy alternators
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet explains how to install a flap over the diesel filling cap
  • IS-17905A - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-11003G - EQUIPMENT: This instruction sheet explains how to replace the ?Master id? With ?Mcm? Module
  • SP18-13F - STEERING:LINKAGES:DRAG:LINK:CONNECTION: On the vehicles affected by this bulletin, proceed to the replacement of the drag link.
  • IS-13009D - STEERING:LINKAGES:DRAG:LINK:CONNECTION: This instruction sheet explains how to install and adjust drag link # 660699
  • IS-11003F - ELECTRICAL SYSTEM: This instruction sheet explains how to replace the "master id with mcm" module
  • SCI18-46 - EQUIPMENT:ELECTRICAL: This service center instructions explains how to install the prevost ultimate entertainment system
  • IS-13009C - STEERING:LINKAGES:DRAG:LINK:CONNECTION: This instruction sheet explains how to install and adjust drag link # 660699
  • IS-18907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install hatches with fan on x3 vehicles.
  • WB18-43 - POWER TRAIN: This warranty bulletin explains how to update the vecu (vehicle electronic control unit) parameters to allow auto engine brake function with the i-shift transmission.
  • IS12010 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to replace the left bell crank using kit 161349
  • MI18-21A - ENGINE AND ENGINE COOLING: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-05 - ENGINE AND ENGINE COOLING: This maintenance information explains how to install valve assembly 130009 in replacement of valve 641274
  • MI16-17G - ENGINE AND ENGINE COOLING: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • MI14-40B - ENGINE AND ENGINE COOLING: This maintenance information presents how to install and remove the bosch hd10 alternator
  • IS-15003E - ELECTRICAL SYSTEM: This insruction sheet explains how to insall the bosch hd10 24v-150a alternator conversion kit ? Twin bosch mounted on volvo d13 engine
  • MI18-21 - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-16A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information presents guidelines to help with the diagnosis of the bosch hd10 alternators
  • SP18-13D - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, proceed to the replacement of the drag link.
  • IS-17905 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-13009B - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install and adjust drag link # 660699
  • SP18-13E - STEERING:LINKAGES:DRAG:LINK:CONNECTION: On the vehicles affected by this bulletin, replace the drag link.
  • MI18-02 - ENGINE AND ENGINE COOLING: This mainteannce informaiton presents the latest engine oil & filter change intervals for the volvo engine
  • MI16-17F - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • SP14-309 - BRAKES (PWS): On the vehicles affected by this special bulletin, replace the two visual brake wear indicators on the tag axle.
  • SP14-311 - ELECTRICAL SYSTEM: On the vehicles affected by this special bulletin, add a 3 amp diode to the corresponding 24co circuit to prevent the combined charging and starting system f81 fuse from blowing.
  • WB14-28E - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, replace the ltd, relocate and replace the ir sensor as described in the following procedure.
  • WB14-03 - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: On the vehicles affected by this bulletin, a new center mount battery box cover offering better overall sealing and simplified installation is available and may be installed at next service occasion.
  • SP14-306D - ENGINE (PWS): On the vehicles affected by this bulletin, replace the engine harness as described in the following procedure.
  • SP14-21G - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, replace and relocate the ltd. Remove the existing ir sensor and install an updated ir sensor. Finally, remove and replace the extinguisher bottle support.
  • MI1423 - ELECTRICAL SYSTEM:SOFTWARE: A new software version (v1.06) is available to update the cantrak (tire pressure monitoring system) module. This new version will allows a 10 min. Delay before the ?System error not all tires monitored? Message appears in the vehicle clust
  • SP14-303A - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, to cancel the did pop-up message ?Windows ajar? Disconnect wire 260 from mux module a42.
  • SP14-302C - VISIBILITY:WINDSHIELD: On the vehicles affected by this bulletin, perform an improvement of the front windshield sun visor guides and supports in addition to the side window sun visor guide support in the driver?S area. The improvement reduces rattling noise from
  • SP14-307A - EQUIPMENT:OTHER:LABELS: On the vehicles affected by this bulletin, install a warning plate.
  • SP14-304 - STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS: On the vehicles affected by this bulletin, replace the sliding door interior post finishing trims as described in the following procedure.
  • SP14-305A - STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS: On the vehicles affected by this bulletin, replace the bi-fold door hinge arm rod ends as described in the following procedure
  • MI1346 - ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS: This maintenance information explains that on some post epa 2010 vehicles, it is possible for the combined charging and starting system f81 fuse to blow unexpectedly. To avoid this situation, a 3 amp diode can be added to the corresponding
  • IS-08080 - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: When replacing a vehicle sound selector model vss04 with a new sound selector model vss05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new vss05 compatible radio unit must also be in
  • SP13-44 - ELECTRICAL SYSTEM: The light switch may operate incorrectly when doors are closed for vehicles affected by this bulletin. Corrective action is presented.
  • MI13-33 - SUSPENSION:MULTIPLE AXLE:TORQUE ARM: This maintenance information explains that polyester reinforced silicone hoses and elbowscan be repalced by aramid reinforced hoses and elbows for improved long term durability, and that constant torque hose clamps for silicone hoses with 5
  • SP13-323 - ENGINE (PWS): On the vehicles affected by this bulletin, update the engine air intake pipe.
  • SP13-322 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, relocate the video fuse in the smi box closer to the door for better access.
  • SP13-321 - EQUIPMENT: On the vehicles affected by this bulletin, at next service occasion, open the c69 connector located in the front compartment and check for presence of corrosion. Relocate the connector horizontally.
  • SP13-320 - EQUIPMENT: On the vehicles affected by this bulletin, if needed, the celling panel needs to be removed and material glued again.
  • SP13-318 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : On the vehicles affected by this bulletin, take the following measure to improve dust handling. Seal the evaporator compartment to prevent dust entry, add ribs inside the duct to prevent collapse by the weight of accumulated dust, modify th
  • SP13-317 - ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS: On the vehicles affected by this bulletin, clean the breakers posts and bus bars, apply corrosion protection. Check compartment cover seal condition.
  • WB13-29 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: On the vehicles affected by this bulletin, a corrective measure is required due to bolts coming loose at the radiator fan clutch tripod attachment to the radiator. Addition of four (4) locknuts (jam nuts) will prevent bolts to loosen.
  • SP13-324 - EQUIPMENT: On the vehicles affected by this bulletin, an improved 90 degree elbow is available. Proceed to replacement at next service occasion.
  • SP13-315 - EQUIPMENT:ELECTRICAL: On the vehicles affected by this bulletin, replace the destination sign power harness to resolve electrical interference between sign and public address (pa) system.
  • MI13-06 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: This maintenance information explains that hose clamps with a smaller diameter are available to increase the adjustment range at the upper and lower radiator flexible connections and at the oil cooler connections located under the turbocha
  • WB13-32B - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL: On the vehicles affected by this bulletin, the nox sensor must be replaced and the ems software requires an update. This must be done to allow correct emissions inspection in particular states including california.
  • SP13-14 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, inspection and replacement of 70 amp circuit breakers in the rear electrical compartments is required.
  • SP13-312 - STRUCTURE:BODY:DOOR: Replace the 4 stressproof steel door studs with the new hex door studs
  • SP13-311 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, multiple codes for psid8 fmi2 or 1 after reprogramming engine, agreed to campaign piston cooling reduction valve to avoid these code creating road calls
  • SP13-19A - STRUCTURE: Grille frame gluing verification on the dpf door (left side, over the radiator door). If part shows no sign of separation or ungluing, it is ok. If testing reveals poor bonding, remove grille, glue and double face tape.
  • SP13-310 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, force uip regen and replace doser modules as requested
  • SP13-10 - POWER TRAIN: A transmission reprogramming is necessary in order to correct and interlock issue between the wheelchair lift system and the i-shift transmission
  • SP13-309 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: Multiple hose failures, agreed with customer to replace silicone hose in engine compartment for coaches with volvo engine.
  • SP13-09 - BRAKES (PWS): Possible premature wear of brakes due to inadequate jacob brake intensity. Parameters change in software is done to fix the issue.
  • SP13-307 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, replace r6 and r13 relay indirect and direct lightening, as premature failure of r6 and r13 due to the relay coil being activitated all the time
  • SP13-306 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE): On the vehicles affected by this bulletin, replace the exhaust gas recirculation venturi tube and sensor for an improved design.
  • SP13-305 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, replace coolant hose for the most recent hose.
  • SP13-304 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, look at all the clamps and retighten as coolant leaks found around the coach.
  • SP13-303 - ENGINE (PWS): On the vehicles affected by this bulletin, reprogram engine to improve piston cooling codes
  • SP13-302 - SEATS: On the vehicles affected by this bulletin, trim wcl seat pedestal block to make them easier to slide back and forward and reduce pedestal failures.
  • SP13-301 - FUEL SYSTEM, GASOLINE: On the vehicles affected by this bulletin, replace booster pump support as vehicles with cracked support found during inspection.
  • SP13-300 - ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL: On the vehicles affected by this bulletin, change one parameter in the cluster software to fix the pid251 clock code.
  • MI12-48 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE: When performing the next periodic maintenance, check clearance between the 4-inch od turbooutlet pipe (prevost part number 052953) and a close support bracket. If evidence of rubbing isfound, i.E. Scratched paint on the 4-inch od turbo outl
  • SP12-313 - PARKING BRAKE: On the vehicles affected by this bulletin, reinforced parking brake overrule tank supports are available.
  • WB12-31B - EQUIPMENT: On the vehicles affected by this bulletin, a new and improved dipstick is available for installation.
  • SP12-306A - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, improvement of a charge air cooler tube support is required. This is a ?Fix as fail? Bulletin, repair only the vehicles showing a cracked cac tube.
  • SP12-312 - ELECTRICAL SYSTEM:WIRING: On the vehicles affected by this bulletin, addition of a power relay to the inverter system wiring is required.
  • WB12-33 - STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS: On the vehicles affected by this bulletin, the wheelchair lift sliding door hinge bolts need to be tightened to ensure proper torque is applied. Procedure should be performed one bolt at a time to preserve door adjustment.
  • IS11015B - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to replace power relay p/n 561991 with improved power relay p/n 564218 and relay base p/n 564210
  • SP12-318 - SEATS:BARRIERS: On the vehicles affected by this bulletin, install washers on front passengers modesty panel to increase gap between hand rail and panel
  • SP12-316 - STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS: On the vehicles affected by this bulletin, the bi?Part door studs must be replaced with latest version .
  • SP12-314 - EQUIPMENT:MECHANICAL: Replace edge moulding retainer clip to improve the reliability of this installation
  • IS12047 - STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS: This instruction sheet explains how to install additional restraint for plastic shields over drive axle wheels. Use kit #3200407 to secure the shields to the bus structure.
  • SP12-315 - STRUCTURE:BODY:DOOR: On the vehicles affected by this bulletin, perform the replacement of the existing wcl sliding door upper arm.
  • SP12-311 - EQUIPMENT:ELECTRICAL: On the vehicles affected by this bulletin, relocation of the wcl pendant is required to avoid driver to pull on the wires when operating wcl
  • SP12-307 - SUSPENSION: On the vehicles affected by this bulletin, replace drive axle radius rod bushings and caps to improve reliability.
  • MI15-51 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: This maintenance information explains how to run a n air conditionning performance test
  • WB15-50 - EQUIPMENT:OTHER:LABELS: On the vehicles affected by this bulletin the rear junction box decal located in the right engine compartment is displaying incorrect information regarding the r34 relay voltage. Specifically, the r34 relay should be identified as a 24 v
  • MI15-61 - ENGINE (PWS): This maintrenance infomration explains that the castrol syntrans oil isn?T fully approved for 500 000 miles (800 000 km) extended drain intervals on the volvo i-shift transmission. For this reason, this oil has been downgraded to regular d
  • IS-15907A - EQUIPMENT:MECHANICAL: This instruction sheet explains how to assemble the bendix flr10 and flr20 radar sensor alignment tool
  • SP15-337B - ENGINE (PWS): On the vehicles affected by this bulletin, install an extension to the ltd cable on the engine curb side.
  • IS-14152 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: This instruction sheet prvides a road side and workshop instructions for replacing 040949 6mm def hose to a 4mm id hose.
  • MI15-41 - EXTERIOR LIGHTING:TAIL LIGHTS: This maintenance information reminds prevost customers that cleaning products designed for external washing of vehicles should be used for exterior vehicle wash and in particular, for the washing of polycarbonate taillights.
  • MI15-43 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on prevost vehicles equipped with bosch hd10 alternators.
  • MI15-18 - EQUIPMENT: This maintenance information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.
  • MI15-24 - EQUIPMENT:MECHANICAL: This maintenance information explains how to perform an inspection of the vehicle power cables. Power cables in poor condition can be the cause of failures and serious damages in the engine compartment.
  • SP15-32 - ELECTRICAL SYSTEM:WIRING: On the vehicles affected by this bulletin, to reduce the possibility of fault codes the dpf differential pressure sensor signal wire needs to be replaced by a single wire from the dpf differential pressure sensor directly to the acm connect
  • SP15-328 - BRAKES (PWS): On the vehicles affected by this bulletin the brake hose may come in contact with the air spring support when vehicle is in low or high buoy position. Perform an inspection. Depending on the result, adjust the hoses to avoid any interferenc
  • SP15-20A - ELECTRICAL SYSTEM:WIRING: To correct the j-1939 can2 and nox sensor faults that have been intermittently logging, a dedicated can harness cable (twisted wires) will run from connector c26 near the acm in the condenser compartment to the splice bar connector s-bar 1
  • SP15-304D - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: On the vehicles affected by this bulletin, the bosch hd10 alternators need to be replaced with new bosch hd10plbh 150 amps alternators.
  • SP15-17 - ENGINE (PWS): On the vehicles affected by this bulletin, replace the engine harness as described in the following procedure.
  • SP15-323 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, install a diffuser pipe thermal insulating wrap to promote higher exhaust temperature at the ahi nozzle tip.
  • SP15-322A - ENGINE AND ENGINE COOLING: For vehicles affected by this bulletin, eliminate connector pin movement and vibration by re-routing the temperature sensor engine harness lead. Also replace the egr temperature sensor.
  • SP15-16A - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, inspect the rear junction box connections; clean terminals and apply black color guard or termin8r lubricant following the procedure below.
  • SP15-22 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, replace the existing inlet & outlet nox sensors by the latest nox sensors.
  • IS-15003A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to use the bosch hd10 24v-150a altenrator conversion kit
  • IS-17907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the volvo electronic logging device (eld)
  • wb17-16 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, remove selected wires from c15 and c58 of the hvac system wiring, and place them in new connectors c15b and c58b. New connectors have a higher amp rating. We recommend inspecting connectors c15 & c
  • SCI17-35 - ELECTRICAL SYSTEM:SOFTWARE: This internal instruction explains how to bench program the fms gateway module used in the eld (electronic logging device) interface kit for pre-obd13 vehicles.
  • MI17-22 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: This maintenance information explains how to inspect the fuel tank cradle mounting screws on a yearly basis
  • SP15-304B - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: On the vehicles affected by this bulletin, the bosch hd10 alternators need to be replaced with new bosch hd10plbh 150 amps alternators.
  • WB15-13 - SUSPENSION: On the independent front suspension level valve linkage of the vehicles affected by this bulletin, a control rod may come in contact with an air reservoir outlet when vehicle rises from low to high buoy. As a result, the vehicle may be leve
  • SP15-309 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: On the vehicles affected by this bulletin, inspect the bosch hd10 alternator connections.
  • MI14-40A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This maintenance inforamtion presents how to install and remove the bosch hd10 alternator
  • IS-14903 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: This instruction sheet explains how to use kit# is14903 to replace the fuel tank
  • IS-14904 - ENGINE AND ENGINE COOLING: This instruction sheet explains how to install a condenser pivot reinforcement plate kit # 454964
  • SP15-303 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, it is necessary to replace the aftertreatment hydrocarbon dosing module.
  • MI15-02 - POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT: This maintenance information presents an improved differential breather kit, identical to the one now used in production. This new breather incorporates a "j" shaped hose that prevents oil leakage and water ingestion while allowing the axle
  • WB14-47B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a software update of ecm (engine control module) and acm (aftertreatment control module) to provide improved temperature-related behaviour. The software will also change urea dosing valve b
  • SP16-19 - ENGINE AND ENGINE COOLING: On certain vehicles equipped with volvo d13 engines, the pinning of the double idler gear is necessary.
  • SP16-09 - FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM: On the vehicles affected by this bulletin, inspect the fuel injectors serial numbers and replace if required.
  • Mi16-15 - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • SP16-301B - ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER: On the vehicles affected by this bulletin, replace the turbocharger actuator (sra).
  • IS-14154 - FUEL SYSTEM, GASOLINE: This instruction sheet explains how to modify the support beam (part # 30022 installation)- as part of the x3 fuel tank installation
  • SP17-308 - EQUIPMENT: This bulletin explains how to improve nyct compressor door hinges
  • SP17-307 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: This bulletin explains how to replace the radiator door upper hinge
  • IS-16100 - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: This instruction sheet explains how to install latest radio models
  • IS-15003D - ELECTRICAL SYSTEM: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • Sp17-305C - ELECTRICAL SYSTEM:WIRING: On the vehicles affected by this bulletin, on the hvac system wiring, remove selected wires from c15 and c58 and place them in new connectors c15b and c58b. New connectors have a higher amp rating.
  • SP16-324 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, disable the windshield upper defrost grid by removing the electrical connections.
  • SP16-316D - FUEL SYSTEM, GASOLINE: On the vehicles affected by this bulletin, the front fuel tank support needs to be improved to prevent fatigue cracks.
  • MI16-32 - POWER TRAIN:DRIVELINE:CENTER SUPPORT BEARING: Explains that improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • MI15-43A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on prevost vehicles.
  • IS-11003A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to replace master id? With ?Mcm? Module
  • SP15-337 - ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES: On the vehicles affected by this bulletin, install an extension to the ltd cable on the engine curb side.
  • SP15-323B - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, install a diffuser pipe thermal insulating wrap to promote higher exhaust temperature at the ahi nozzle tip.
  • WB15-26B - SUSPENSION:REAR:SPRINGS:AIR SUSPENSION SYSTEM: On the vehicles affected by this bulletin the brake hose may come in contact with the air spring support when the front axle is in low or high position, either by kneeling or low-high buoy. Perform an inspection. Depending on the result, ad
  • WB15-13A - SUSPENSION:REAR:SPRINGS:AIR SUSPENSION SYSTEM: On the independent front suspension level valve linkage of the vehicles affected by this bulletin, a control rod may come in contact with an air reservoir outlet when vehicle rises from low to high buoy. As a result, the vehicle may be leve
  • SP15-33A - EQUIPMENT:MECHANICAL: On the vehicles affected by this bulletin, perform the components replacement as described in this document.
  • SP15-21 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, to prevent premature corrosion of the rear junction box components, replace the junction box cover with a late model "central mount" cover.
  • SP15-17A - ENGINE (PWS): On the vehicles affected by this bulletin, replace the engine harness as described in the following procedure.
  • SP17-308A - STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS: This bulletin explains how to improve nyct compressor door hinges
  • Sp17-305B - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, on the hvac system wiring, remove selected wires from c15 and c58 and place them in new connectors c15b and c58b. New connectors have a higher amp rating.
  • CK17-27 - EQUIPMENT ADAPTIVE/MOBILITY: This conversion kit explains how to to disable the acb radar.
  • SP16-316E - FUEL SYSTEM, GASOLINE: On the vehicles affected by this bulletin, the front fuel tank support needs to be improved to prevent fatigue cracks.
  • SP16-311B - EQUIPMENT: On the vehicles affected by this bulletin, add two clips to secure the direct light lenses, 13 lenses per vehicle.
  • SP16-308A - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, add a stopper on the a/c compressor support bed to prevent any movement.
  • IS-15003B - EQUIPMENT: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • SP14-24C - POWER TRAIN:AXLE ASSEMBLY: On the vehicles affected by this bulletin, the bushings found on the drive axle longitudinal radius rods have to be replaced.
  • SP14-22 - STEERING: On the vehicles affected by this bulletin, the existing lower steering column cover hardware has to be replaced for improved fastening system.
  • SP14-19 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, remove the existing jacket hooks and install one new hook.
  • SP14-18 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, replace the screws found on a finishing panel with rivets.
  • IS-14900 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to replace 562489 dimmer, using kit #069136
  • SP14-300B - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, the engine oil pressure sensors for the piston cooling jet (pcj) and the main oil gallery have to be replaced with an updated pressure sensor to avoid erroneous low oil pressure diagnostic codes.
  • SP14-05B - ENGINE (PWS): On the vehicles affected by this bulletin, perform a turbo replacement if fault codes 27 fmi 7 or spn641 fmi 7 or P004607 (obd13) are found. Bulletin affects d13h engines with serial number from 984581 up to 1026719, excluded.
  • MI16-15B - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • SP16-316C - FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY: On the vehicles affected by this bulletin, the front fuel tank support needs to be improved to prevent fatigue cracks.
  • Sp16-307A - ENGINE (PWS): On the vehicles affected by this bulletin, replace the egr venturi tube on the d13 engine by an improved version.
  • IS-11003D - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to remplace master id? With ?Mcm? Module
  • Sp16-311A - EQUIPMENT: On the vehicles affected by this bulletin, add two clips to secure the direct light lenses, 13 lenses per vehicle.
  • SP16-21 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, perform the proactive replacement of the lower hinges for both service doors.
  • MI16-22 - EQUIPMENT ADAPTIVE/MOBILITY: Use this maintenance information procedure to resolve an undesired behaviour on 2008-2012 vehicles. In sleep mode, certain marker lights may remain illuminated.
  • SP16-25 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin install an updated proximity switch on the vehicle compressor door following instruction sheet is-12026.
  • MI16-15A - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • MI12-04C - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintneance informations presents an improved harness and wiring modification procedure to avoid certain fault codes and messages.
  • MI16-16 - ELECTRICAL SYSTEM: This procedure explains how to perform a starter removal and installation, and does apply to melco 105p70 starter part number #21212425.
  • SP15-304E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: On the vehicles affected by this bulletin, the bosch hd10 alternators need to be replaced with new bosch hd10plbh 150 amps alternators.
  • SP16-301 - ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER: On the vehicles affected by this bulletin, replace the turbocharger actuator (sra).
  • CK17-19A - EQUIPMENT: This conversion kit explains how to remove tgw1 from vehicles using tech tool, no manual vda changes needed. This conversion kit will work for any vehicle equipped with tgw1 up to the vin's listed on the bulletin.
  • IS-11003E - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to remplace master id? With ?Mcm? Module
  • WB17-16 - EQUIPMENT:ELECTRICAL: On the vehicles affected by this bulletin, on the hvac system wiring, remove selected wires from c15 and c58 and place them in new connectors c15b and c58b. New connectors have a higher amp rating.
  • SP16-311G - EQUIPMENT: On the vehicles affected by this bulletin, add z clips to secure the direct light lenses, 13 lenses per vehicle.
  • IS-17901 - BRAKES (PWS): This instructions sheet explains how to program a wabco smart trac abs ecu.
  • IS-15003D - ENGINE (PWS): This insruction sheet explains how to insall the bosch hd10 24v-150a alternator conversion kit ? Twin bosch mounted on volvo d13 engine
  • Sp17-305 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, on the hvac system wiring, remove selected wires from c15 and c58 and place them in new connectors c15b and c58b. New connectors have a higher amp rating.
  • SP14-320B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a software update of ecm and acm to modify the dosing strategy. The software will also improve urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the u
  • WB14-47B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a software update of ecm (engine control module) and acm (aftertreatment control module) to provide improved temperature-related behaviour. The software will also change urea dosing valve b
  • SP14-312D - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, perform a software update of ems and acm to modify the dosing strategy. The software will also improve urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the u
  • WB14-45C - ELECTRICAL SYSTEM:WIRING: On the vehicles affected by this bulletin remove the acm relay and base identified r49. Reconnect the 24v power wire and protect the remaining signal wires with shrink tube.
  • WB14-32 - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: On the vehicles affected by this bulletin, it is possible to observe signs of corrosion at the base of the master relay installed in the vehicle battery box. At the next service occasion, install a new relay along with shims between the re
  • SP14-313 - ELECTRICAL SYSTEM: On the vehicles affected by this special bulletin, a 7psi pressure switch must be added to the transmission retarder circuit to activate the retarder when vehicle brakes are applied, increasing drivetrain components reliability.
  • SP14-310 - POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT: On the vehicles affected by this bulletin, perform the repair procedure included in this document.
  • SP13-341C - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, four (4) reinforcement brackets must be added to the dpf support.
  • WB13-91A - VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR: On the vehicles affected by this bulletin, replace the valeo wiper motor by a bosch wiper motor.
  • WB13-65D - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, software updates with enhancements are available for the multiplex system, for the ems and aftertreatment control module (acm). On all vehicles, perform a dpf service regeneration and crystal subli
  • SP13-340 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, it is possible to experience sudden coolant fan belt snapping due to excessive force applied to the belt. Therefore, it is necessary to replace the current belt (part # 5061284) with a new severe d
  • SP13-339 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, the pcj oil pressure sensor has to be replaced with an updated pressure sensor to avoid erroneous low oil pressure diagnostic codes.
  • SP13-335 - EQUIPMENT:ELECTRICAL: On the vehicles affected by this bulletin, the audio selector (a34) and r44 relay must be replaced with a new double throw relay in order to avoid sound interference in the pa system when a message from the command center is broadcasted.
  • SP13-334 - STRUCTURE:BODY:BUMPERS: On the vehicles affected by this bulletin, trim the rear bumper to avoid contact with the rear lateral service doors. Also perform the proactive replacement of the lower hinges for both service doors.
  • SP13-333A - ELECTRICAL SYSTEM: On vehicles affected by this bulletin, a removal of three connectors that were in the original harness and causing associated resistance and voltage drops across them. As a result, nox sensor faults that have been intermittently logging, a
  • WB13-58 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: On the vehicles affected by this bulletin, change the flexible hose at the engine air intake
  • WB13-60 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, a software update for the volvo i-shift transmission is required. Software update has for effect to improve the gear change process to avoid clashing and wear on the split gear. This software updat
  • SP13-69 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Possible air return between evaporator air conduit and compartment. No airtightness between duct and floor / floor structure. Bulletin to describe how to add a sealing joint for better air tightness.
  • WB13-63A - ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS: On the vehicles affected by this bulletin, inspection and replacement of 70 amp circuit breakers in the rear electrical compartments is required.
  • WB13-62B - POWER TRAIN:AXLE ASSEMBLY: On the vehicles affected by this bulletin, torque must be verified on one of the axle support mounting bolts. An interference of a production tool with the casting on the nut side of the fastener may have resulted in lower effective torque.
  • SP13-328F - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the bosch hd10 alternators needs to be replaced.
  • SP13-330B - EXTERIOR LIGHTING:TURN SIGNAL: On the vehicles affected by this bulletin, the turn signal foot switches and horn foot switch might be working intermittently and needs to be replaced.
  • SP13-332E - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: On the vehicles affected by this bulletin, the fuel tank vent hose must be replaced with a hose that can withstand fuel vapor.
  • SP13-329E - STRUCTURE:BODY: On the vehicles affected by this bulletin, reinforcement brackets must be added to address cracking issue
  • SP13-326B - STRUCTURE:BODY:DOOR: On the vehicles affected by this bulletin, addition of a bolted structural reinforcement is required on the aft bi-fold door cylinder support.
  • SP13-327C - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: New exhaust pipe support installation ? Solution for cracking issue
  • WB13-49 - FUEL SYSTEM, DIESEL: On the vehicles affected by this bulletin, replace the prototype version of the urea quality sensor #21891229 by the production version of the sensor #22073036.
  • MI16-17E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternator.
  • IS-15003C - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • SP16-319B - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, replace the pitman arm nut and re-torque to specification.
  • MI16-34 - ELECTRICAL SYSTEM: "this maintenance information describes the steps to be followed on your computer to add the volvo engine brake auto mode on the vehicle. The auto mode may be added on us10 and obd13 vehicles that were built before the introduction of the
  • IS-08080A - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: When replacing a vehicle sound selector model vss04 with a new sound selector model vss05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new vss05 compatible radio unit must also be in
  • SP15-328 - SERVICE BRAKES, AIR:SUPPLY:HOSES, LINES/PIPING, AND FITTINGS: Summary to be provided on a future date.
  • SP15-322A - ENGINE (PWS): Summary to be provided on a future date.
  • WB15-13 - SUSPENSION: Summary to be provided on a future date.
  • SP15-33 - EQUIPMENT: Summary to be provided on a future date.
  • SP15-21 - EQUIPMENT: Summary to be provided on a future date.
  • SP15-17A - EQUIPMENT: Summary to be provided on a future date.
  • SP-15-328 - SERVICE BRAKES, AIR:SUPPLY:HOSES, LINES/PIPING, AND FITTINGS: Prevost: when bus in position of low or high buoy, brake hose will contact air spring support and would need inspected and adjusted, for hose to not interfere. Model 2012-15 x3-45. *pe
  • SP-15-309 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: Prevost: bosch hd 10 alternator connections, on some buses, need to be inspected and may need other parts and materials, if required. Model 2011-14. *pe
  • SP-15-322A - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE): Prevost: the temperature sensor engine harness lead has been re-routed due to elimination of vibration and connector pin movement and egr temperature sensor has also been replaced. Model 2012 x3-45. *pe
  • WB-15-13 - SUSPENSION:FRONT: Prevost: warranty issued, on some buses, regarding control rod of independent front suspension level valve, contacting air reservoir outlet when going low to high buoy. Model 2012-15 x3-45. *pe
  • SP-15-33 - EQUIPMENT: Prevost: some buses will need replacements of certain components-pcj oil pressure sensor, ats doser module and piston cooling reduction valve. Model 2011-12 x3-45. *pe
  • SP-15-21 - EQUIPMENT: Prevost: on some buses, the junction rear component box cover would be replaced to prevent premature corrosion. Model x3-45. *pe
  • SP-15-20-2 - ENGINE (PWS): Prevost: on some buses, by vin, will have installed the j-1939 can2 engine subnet cable overlay, due to intermittent logging. Model 2011-13 x3-45. *pe
  • SP-15-16 - EQUIPMENT: Prevost: rear junction box connections need inspected with clean terminals and termin8r lubricant or black color guard should be applied following required procedure. Model 2011-14 x3-45 (gli). *pe
  • WB14-32 - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: Prevost: information regarding base of the master relay installed, showing signs of corrosion, in the vehicle battery box of coaches 2010-2013, entertainer 2011-2013 and vip motorhomes 2012-2013. *lj
  • WB-13-91 - VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR: Prevost: information provided on replacing valeo wiper motor with bosch wiper motor. Model 2011-2012 x3-45 commuter, coaches. *pe
  • MI-13-46 - ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS: Prevost: the combined charging and starting system f81 fuse, on some coaches, can unexpectedly blow and need a 3 amp diode to corresponding 24co circuit to prevent electrical back flow to fuse. Models 2011-2013 h3, h3-45 vip converted, x
  • WB-13-32 - ELECTRICAL SYSTEM:SOFTWARE: Prevost: the nox sensor must be replaced and the ems software needs updating to correct emissions inspections on certain coaches. Models 2012-2013 h3-45, h3 vip, x3-45, le mirage xlii. *pe
  • WB-13-29 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: Prevost: a corrective measure is required due to bolts loosen by being tightened to part made of rubber, causing the radiator fan clutch tripod to come loose and striking radiator core. *pe
  • MI-13-06 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: Prevost: to increase vehicle's performance, a modification of hose clamp for cooling system connection, is recommended. Models 2010-13 h3, 2010-13 h3 vip converted, 2010-13 x3, 2012-13 x3 vip converted, 2010-13 mth xl2 entertainer, 2011 m
  • SP-12-315 - STRUCTURE:BODY:DOOR: Prevost: the sliding door, on certain vans/trucks, with wheelchair lift, the upper arm needs to be replaced. Model 2012 x3-45. *pe
  • WB-12-31 - EQUIPMENT ADAPTIVE/MOBILITY: Prevost: information being provided regarding the replacement of dipstick on certain coaches. Models 2009-2013 h3-45, h3-41, x3-45, xl11-45, x3-45. *pe
  • MI-12-48 - ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER: Prevost: if rubbing found on 4 inch od turbo outlet pipe, after closing support bracket, then to increase clearance between involved components, a modification of support bracket must be performed. No model or model years listed. *
  • WB-12-18 - ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS: Prevost: power is not removed when unplugging fuse f45 to fire protection panel on driver's left console where modification of harness must be performed. Models 2012-2013 h3-41, h3-45, x3-45, xlii-45 (coach, commuter & vip shell). *
  • SP-12-23 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE): Prevost: corrective measure for the egr valve is necessary because of the unnecessary presence of o-rings, which may prevent free valve actuation. Egr valve can be replaced with latest version. Models 2012-13 h3-41, h3-h45 coaches, h3-45
Known Recall Investigations
  • Alternator front bearing failure investigation # PE21011

    There is no summary currently available

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.