2019 Hyundai VELOSTERHyundai Veloster 2019

Complaint Information: Recalls, Consumer Complaints, Service Bulletins, OBD II Codes

NHTSA Mandated Recalls
  • Recall 208358 [USA]: A damaged engine may stall, increasing the risk of a crash. in addition, oil may leak onto hot exhaust components, increasing the risk of a fire.
    Hyundai motor america (hyundai) is recalling certain 2019-2020 elantra, 2019-2021 kona and veloster vehicles equipped with 2.0l nu mpi engines. The piston oil rings may not have been properly heat-treated, which could result in engine damage.
    dealers will inspect and, if necessary, replace the engine, free of charge. In addition, hyundai will deploy piston ring noise sensing system (pnss) software. Owner notification letters were mailed august 24, 2021. Owners may contact hyundai customer service at 1-855-371-9460.
    owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  • Recall 141653 [USA]: The door opening could result in occupant ejection or increase the risk of injury in the event of a crash.
    Hyundai motor america (hyundai) is recalling certain 2019 veloster vehicles. In certain side impact crashes, the driver's door latch housing and locking cable can become damaged, allowing the driver's side door to open.
    hyundai will notify owners, and dealers will replace the driver's side door latch assembly and lower channel, free of charge. The recall began june 17, 2019. Owners may contact hyundai customer service at 1-855-371-9460. Hyundai's number for this recall is 183.
    owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  • Recall 2021252 [Canada]: Engine
    Issue: on certain vehicles, the engine's piston oil rings may be defective. This can cause engine wear that can lead to increased oil consumption. Eventually, this can create abnormal engine noise and the oil pressure warning light may turn on. If you continue to drive the vehicle with these symptoms, the engine could fail. Note: this only affects vehicles equipped with a 2.0 l nu mpi engine. Safety risk: a sudden loss of engine power could increase the risk of a crash. An engine failure could also create the risk of a fire. Corrective actions: hyundai will notify owners by mail and instruct you to take your vehicle to a dealer to inspect the engine. The engine will be replaced, if necessary. Hyundai is also developing a piston-ring noise sensing system (pnss) software update to be installed when available; it will alert the driver of potential damage before an engine failure occurs.

  • Recall 2019640 [Canada]: Engine
    Issue: hyundai auto canada is conducting a product improvement campaign that provides an update to the engine control module to detect potential problems before an engine fails. An engine failure would cause a sudden loss of power with an inability to restart. Note: this affects sonata and santa fe sport equipped with a 2.4 l gdi or 2.0 l turbo gdi engine, as well as tucson equipped with a 2.4 l gdi engine. Safety risk: a sudden loss of engine power could increase the risk of an accident. Corrective actions: the company will notify owners by mail. Owners will be instructed to take their vehicle to a dealer to update the software for the engine control module. Note: vehicles previously repaired under product improvement campaign r0153 (tc # 2019-130) do not require this software update. Owners can find additional information at www.Hyundaiengineinfo.Ca.

  • Recall 2019208 [Canada]: Structure
    Issue: on certain cars, the driver’s door could open in a side impact crash. Safety risk: a door that opens in a crash could create a risk of being ejected from the car and create an increased risk of injury. Corrective actions: hyundai will notify owners by mail and instruct them to take their vehicle to a dealer to replace the door latch assembly.

  • Recall 2018684 [Canada]: Airbag
    On certain vehicles, the impact sensors programming for the airbag control unit (acu) may be incorrect. In the event of a crash, if the acu detects a fault related to the impact sensors, the airbag system may not deploy the airbag(s) properly, which could increase the risk of injury to vehicle occupants. Correction: dealers will reprogram the airbag control unit. Note: only “veloster n” vehicles are affected.

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • 24-AT-002H - POWER TRAIN: This tsb provides a procedure to diagnose and replace, if necessary, an automatic transmission with incorrect ratio dtc (transmission clutch slip in gear above limit) listed on page 2.
  • 24-BD-001H - VISIBILITY: This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming
  • 24-01-009H - ELECTRICAL SYSTEM: Hyundai has launched an anti-theft software upgrade and window decal campaign (campaign 993), combined with an anti-theft steering wheel lock campaign (campaign p32), and anti-theft ignition cylinder protector campaign (campaign 9a5) in res
  • 24-01-009H - ELECTRICAL SYSTEM: This bulletin provides the service procedure to: 1) upgrade the ibu/bcm (integrated body control unit/body control module) to revise the oem hyundai burglar alarm system operation and ignition start logic and 2) install two anti-theft decal
  • 24-01-009H - ELECTRICAL SYSTEM: Hyundai has launched an anti-theft software upgrade and window decal campaign (campaign 993), combined with an anti-theft steering wheel lock campaign (campaign p32), and anti-theft ignition cylinder protector campaign (campaign 9a5) in res
  • 23-01-014H-6 - ELECTRICAL SYSTEM: Hyundai has launched an anti-theft software upgrade and window decal campaign (campaign 993), combined with an anti-theft steering wheel lock campaign (campaign p32), and anti-theft ignition cylinder protector campaign (campaign 9a5) in res
  • 23-01-014H-6 - ELECTRICAL SYSTEM: Hyundai has launched an anti-theft software upgrade and window decal campaign (campaign 993), combined with an anti-theft steering wheel lock campaign (campaign p32), and anti-theft ignition cylinder protector campaign (campaign 9a5) in res
  • 23-EM-005H - ENGINE AND ENGINE COOLING: This bulletin provides important checkpoint guidelines when performing engine oil and filter change services.
  • 23-01-014H-6 - ELECTRICAL SYSTEM: Certain hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the ibu/bcm (integrated body control unit/body control module), to revise the oem hyundai burglar alarm system operati
  • 23-01-014H-6 - ELECTRICAL SYSTEM: Hyundai has launched an anti-theft software upgrade and window decal campaign (campaign 993), combined with an anti-theft steering wheel lock campaign (campaign p32), in response to an increase in thefts of certain 2011-2022my hyundai vehic
  • 23-01-014H-5 - ELECTRICAL SYSTEM: Hyundai has launched an anti-theft software upgrade and window decal campaign (campaign 993), combined with an anti-theft steering wheel lock campaign (campaign p32), in response to an increase in thefts of certain 2011-2022my hyundai vehic
  • 23-01-014H-5 - POWER TRAIN: Hyundai has launched an anti-theft software upgrade and window decal campaign (campaign 993), combined with an anti-theft steering wheel lock campaign (campaign p32), in response to an increase in thefts of certain 2011-2022my hyundai vehic
  • 23-BE-010H - ELECTRICAL SYSTEM: Some models from service campaign 993 (ibu/bcm software update and decals application) equipped with the hyundai oem remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. Thi
  • 23-BE-007H - ELECTRICAL SYSTEM: This service information bulletin provides information on how to update the apple carplay software from hyundaia??S navigation updates page. The current version of google maps has 10 times the data transmission compared to the previous vers
  • 23-01-014H-5 - ELECTRICAL SYSTEM: Hyundai has launched an anti-theft software upgrade and window decal campaign (campaign 993), combined with an anti-theft steering wheel lock campaign (campaign p32), in response to an increase in thefts of certain 2011-2022my hyundai vehic
  • 23-01-014H-5 - ELECTRICAL SYSTEM: Certain hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the ibu/bcm (integrated body control unit/body control module), to revise the oem hyundai burglar alarm system operati
  • 23-01-014H-5 - ELECTRICAL SYSTEM: Certain hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the ibu/bcm (integrated body control unit/body control module), to revise the oem hyundai burglar alarm system operati
  • 23-01-014H-4 - ELECTRICAL SYSTEM: Certain hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the ibu/bcm (integrated body control unit/body control module), to revise the oem hyundai burglar alarm system operati
  • 23-BD-007H - STRUCTURE:BODY: Hyundai applies a paint protection film (ppf) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can becom
  • 23-01-014H-4 - ELECTRICAL SYSTEM: Certain hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the ibu/bcm (integrated body control unit/body control module), to revise the oem hyundai burglar alarm system operati
  • 23-01-014H-4 - ELECTRICAL SYSTEM: Hyundai has launched an anti-theft software upgrade and window decal campaign (campaign 993) in response to an increase in thefts of certain hyundai vehicles not equipped with engine immobilizers targeted through social media. In november 2
  • 23-01-014H-3 - ELECTRICAL SYSTEM: Certain hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the ibu/bcm (integrated body control unit/body control module), to revise the oem hyundai burglar alarm system operati
  • 23-01-014H-2 - ELECTRICAL SYSTEM: Hyundai has launched an anti-theft software upgrade and window decal campaign (campaign 993) in response to an increase in thefts of certain hyundai vehicles not equipped with engine immobilizers targeted through social media. In november 2
  • 23-01-014H-2 - ELECTRICAL SYSTEM: Certain hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the ibu/bcm (integrated body control unit/body control module), to revise the oem hyundai burglar alarm system operati
  • 23-BE-002H - ELECTRICAL SYSTEM: This bulletin provides information to upgrade the bcw (blind-spot collision warning) software for certain 2019-22my veloster n (jsn) vehicles (see applicable vehicles below). A?? Symptom: bcw lamp illuminated intermittently with no vehicle
  • 23-BD-002H - VISIBILITY: This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (drl), or fog lamp. This tsb illustrates the various causes of condensation inside th
  • 22-GI-006H - TIRES: Effective june 2, 2008, federal motor vehicle safety standard 110 (fmvss 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale
  • 22-EM-010H - ENGINE AND ENGINE COOLING: Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement.
  • 22-ST-007H - WHEELS: N vehicles are designed to maximize dynamic steering performance. In normal ackerman steering geometry, the inner front tire turns more than the outer tire to help cornering in low-speed situations, i.E., parking lot maneuvering or sharp u-
  • 22-EM-008H - EQUIPMENT ADAPTIVE/MOBILITY: Hyundai is conducting a service campaign 974 to enhance the knock sensor logic with the cylinder noise diagnostic system (cnds) software update. Cnds is to detect abnormal cylinder wall scuffing or noise of the engine block before potential
  • 22-01-043H - ELECTRICAL SYSTEM:SOFTWARE: Hyundai is conducting a service campaign to enhance the knock sensor logic with the cylinder noise diagnostic system (cnds) software update. Cnds is to detect abnormal cylinder wall scuffing or noise of the engine block before potentially s
  • 22-EM-002H-1 - ENGINE AND ENGINE COOLING: The warranty coverage for engine long block repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of fi
  • 22-01-033H - ENGINE AND ENGINE COOLING: Applicable vehicles with 2.0l t-gdi and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326 and/or engine may exhibit abnormal noise or no crank/no start condition. Follow the procedure to inspect the ve
  • DBPT3G - ENGINE AND ENGINE COOLING: Certain vehicles with 2.0l t-gdi and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326 and/or engine may exhibit abnormal noise or no crank/no start condition related to connecting rod bearing wear or
  • 22-EM-004H - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This bulletin provides additional service diagnostic information and repair procedures related to electric waste gate actuator (ewga) equipped vehicles listed below. Refer to the applicable engine control / fuel system sections in the shop
  • 22-EM-002H - EQUIPMENT: The warranty coverage for engine long block repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of fi
  • TXXC DBP - EQUIPMENT: The warranty coverage for certain theta ii engine long block repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to 10 years or 120,000 miles from the date of original retail deliv
  • T3GDBP20211103 - ENGINE AND ENGINE COOLING: Hyundai has launched a service campaign for applicable vehicles with 2.0l turbo and 2.4l gdi engines that may experience the check engine warning lamp illuminated with dtc P1326.
  • 21-01-066H - ENGINE AND ENGINE COOLING: Applicable vehicles with 2.0l t-gdi and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326 and/or engine may exhibit abnormal noise or no crank/no start condition. Follow the procedure to inspect the ve
  • 21-EM-009H - ENGINE AND ENGINE COOLING: This bulletin provides additional service diagnostic information and repair procedures related to electric waste gate actuator (ewga) equipped vehicles listed below. Refer to the applicable engine control / fuel system sections in the shop
  • 21-EM-008H - ENGINE AND ENGINE COOLING: This bulletin provides additional service diagnostic information and repair procedures related to variable charge motion controllers (vcm) equipped in the applicable vehicles listed below. This bulletin also provides information on the use
  • 21-EM-004H - ENGINE AND ENGINE COOLING: This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the bearing clearance test inspection requirements to determine next required steps
  • 21-BR-002H - BRAKES (PWS): This bulletin provides best practice recommendations when performing brake service procedures.
  • 21-EM-003H - ENGINE AND ENGINE COOLING: This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below.
  • 21-ST-001H - STEERING: The rack-mounted dual pinion motor driven power steering (mdps) system components can be replaced separately from the complete assembly. This bulletin provides information on the separate components and the replacement procedure of these co
  • 21-01-002H - ENGINE AND ENGINE COOLING: The warranty coverage for the engine long block for engine repairs or replacement related to connecting rod bearing damage as described in campaign t3g (seized and/or bct no pass result only) has been extended to 10 years or 120,000 miles f
  • 20-01-024H-2 - ELECTRICAL SYSTEM:SOFTWARE: Applicable vehicles with 2.0l turbo and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ecu software based on
  • 20-01-004H-3 - ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER: Applicable vehicles with 2.0l turbo and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ecu software based on
  • 20-BR-002H - BRAKES (PWS): This bulletin describes the procedure to inspect and identify fluid which may appear around the brake caliper area.
  • 20-SS-004H - WHEELS: This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. For all wheel/tire balance claims, the ⿿tire balance data sheet⿝ must be fully completed including imbalance and road for
  • 20-01-024H-1 - ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE: Applicable vehicles with 2.0l turbo and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ecu software based on
  • 20-01-004H-2 - ELECTRICAL SYSTEM:SOFTWARE: Applicable vehicles with 2.0l turbo and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ecu software based on
  • 20-01-039H - EQUIPMENT: This bulletin provides information and procedures for collecting obd ⿿in use monitor performance ratio⿝ (iumpr) data on certain 2019-2021my vehicles at california dealers. This reporting is mandated by carb (california air resources boa
  • 20-01-037H - ENGINE AND ENGINE COOLING: The warranty coverage for the engine long block has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
  • 20-01-036H - ENGINE AND ENGINE COOLING: This bulletin provides information related to an ecm (engine control module) software update for dtc P0128: coolant thermostat (coolant temp below thermostat regulating temperature) logic revision. There are no drivability symptoms associat
  • 20-ST-001H-2 - EQUIPMENT: This bulletin provides information regarding replacement of the column-mounted motor driven power steering (mdps) system as separate components.
  • 20-ST-001H-1 - STEERING:AUTOMATED/ADAPTIVE STEERING:MOTOR/ACTUATOR: This bulletin provides information regarding replacement of the column-mounted motor driven power steering (mdps) system as separate components.
  • 20-BD-006H-1 - LATCHES/LOCKS/LINKAGES: This bulletin describes the procedure to replace the latch and channel of a driver side door that has difficulty opening.
  • 20-FL-006H-1 - ELECTRICAL SYSTEM:SOFTWARE: This bulletin provides information related to the engine control module (ecm) software logic update for dtc P0300-P0304 misfire. This update addresses the intermittent misfire that may only occur at cold engine warmup.
  • 20-BD-014H - EQUIPMENT ADAPTIVE/MOBILITY: This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (drl), or fog lamp. The tsb illustrates the various causes of condensation inside the la
  • 20-FL-006H - ELECTRICAL SYSTEM:SOFTWARE: This bulletin provides information related to the engine control module (ecm) software logic update for dtc P0300-P0304 misfire. This update addresses an incident of intermittent misfire that may only occur at cold engine warmup.
  • Campaign T3G Dea - ENGINE (PWS): Applicable vehicles with 2.0l turbo and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326. Follow the procedures on tsb #20-01-004h-1 (supersedes tsb #20-01-004h) to inspect the vehicle and replace the
  • 20-01-004H-1 - ENGINE (PWS): Applicable vehicles with 2.0l turbo and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ecu software based on
  • 20-01-024H - ENGINE (PWS): Applicable vehicles with 2.0l turbo and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ecu software based on
  • 20-AT-018H - POWER TRAIN: If you are servicing an applicable vehicle with the following symptoms and dtc, follow the service procedure on page 3. ￷ check engine light on ￷ dtc P0880/P088000 - tcm power signal error open/short ￷ transmission stuck in 4th ge
  • 20-SS-002H(1) - WHEELS: This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance.
  • 20-BD-007H-1 - EQUIPMENT: This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products.
  • 20-EE-003H - EQUIPMENT: This bulletin provides information on identifying dealer stock vehicles with either: ⿢ a battery soc alert - low battery state of charge (soc) at or below 50%. ⿢ a 30 day alert - vehicle has not started and reported an soc in 30 days.
  • 20-AT-016H - EQUIPMENT ADAPTIVE/MOBILITY: The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both oem (new) and remanufactured automatic transmissions:
  • 20-AT-015H - EQUIPMENT ADAPTIVE/MOBILITY: If you are servicing an applicable vehicle with a ⿿check engine⿝ light on and one or more of the dtc listed below, follow the repair procedure and replace the oil pressure harness.
  • 20-AT-012H - SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR: If you are servicing an applicable vehicle with a (check engine light on) and one or more of the dtc listed below, follow the repair procedure and replace the input/output speed sensor and oil pressure harness.
  • 20-BD-007H - EQUIPMENT ADAPTIVE/MOBILITY: This bulletin describes the general guidelines to disinfect and protect vehicle interior surfaces using certain safe chemical products.
  • 20-EE-002H(1) - ELECTRICAL SYSTEM: This bulletin describes the mandatory procedure to submit battery test data electronically for battery warranty claims by running the gds battery claim app. The app must be run right after an incident battery is removed from the vehicle or
  • 20-BD-006H - LATCHES/LOCKS/LINKAGES: This bulletin describes the procedure to apply grease to the coupling lever of a door latch that has difficulty opening.
  • 20-BD-006H - LATCHES/LOCKS/LINKAGES: This bulletin describes the procedure to apply grease to the coupling lever of a door latch that has difficulty opening.
  • Campaign T3G DBP - EQUIPMENT ADAPTIVE/MOBILITY: Applicable vehicles with 2.0l turbo and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326. Follow the procedures on tsb #20-01-004h (supersedes tsb #19-01-006h-4) rotate the crankshaft, perform the bea
  • 20-AT-007H - EQUIPMENT: If you are servicing an applicable vehicle with a ⿿check engine⿝ light on and one or more of the dtc listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
  • 20-01-004H - The - ELECTRICAL SYSTEM:SOFTWARE: Applicable vehicles with 2.0l turbo and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ecu software based on
  • 20-01-006H - ELECTRICAL SYSTEM:SOFTWARE: Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the malfunction
  • Campaign 953 Dea - ELECTRICAL SYSTEM:SOFTWARE: Hyundai has developed a new engine monitoring technology called a knock sensor detection system (ksds). The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an
  • 20-SS-001H - SUSPENSION: This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years.
  • 20-AT-001H - POWER TRAIN: This tsb provides a procedure to diagnose and repair a transaxle for the following incorrect ratio dtc (transaxle clutch slipping more than 200 rpm in gear).
  • 20-ST-001H - STEERING: This bulletin provides information regarding replacement of the column-mounted motor driven power steering (mdps) system as separate components.
  • 20-BE-001H - ELECTRICAL SYSTEM: This bulletin provides guidelines to inspect the usb, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common android auto and apple carplay connection conditions. 3. This bullet
  • 19-01-042H - EQUIPMENT: This bulletin provides information and procedures for collecting obd ?In use monitor performance ratio? (iumpr) data on certain 2019-2020my vehicles at california dealers. This reporting is mandated by carb (california air resources board).
  • 19-AT-021H-1 - EQUIPMENT: If you are servicing a vehicle with a transmission slipping concern, follow the service procedure shown below and perform a stall test. This tsb provides a procedure to test each clutch in the transmission. If the vehicle fails the stall te
  • 19-AT-024H - ELECTRICAL SYSTEM: If you are servicing a vehicle with the dtc or symptoms listed below, refer to the service procedure to diagnose the condition. ? Diagnostic trouble codes: ?P0705 - range switch sensor circuit ?P0706 - range switch range/performance ?P07
  • 19-01-016H-1 - ELECTRICAL SYSTEM: This bulletin provides information related to an ecm (engine control module) software update for dtc P0128: coolant thermostat (coolant temp below thermostat regulating temperature) logic revision. There are no drivability symptoms associat
  • Campaign T3T Dea - ELECTRICAL SYSTEM:SOFTWARE: Hyundai has launched a service campaign to update the ecm (engine control module) software for dtc P0128: coolant thermostat (coolant temp below thermostat regulating temperature) logic improvement.
  • 19-BE-011H-1 - BACK OVER PREVENTION: The blind spot detection (bsd) or blind-spot collision warning (bcw) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The bsd/bcw detects v
  • Campaign T4F Dea - ENGINE (PWS): Hyundai is conducting a service campaign to perform an ecm software update to revise the battery sensor data to optimize soc (state of charge) value. The ecm update also includes an update for misfire due to learning cylinder imbalance.
  • 19-01-005H-1 - ENGINE (PWS): The warranty coverage for the engine long block has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
  • 19-01-006H-4 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Applicable vehicles with 2.0l turbo and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326. Follow the procedure to inspect the vehicle and install a wire harness extension and/or replacement engine bas
  • 19-01-002H-4 - ENGINE (PWS): Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the malfunction
  • Campaign 953 Dea - ENGINE (PWS): Hyundai has developed a new engine monitoring technology called a knock sensor detection system (ksds). The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an
  • Campaign T3G Dea - ENGINE (PWS): Hyundai has launched a service campaign for applicable vehicles with 2.0l turbo and 2.4l gdi engines that may experience the check engine warning lamp illuminated with dtc P132600.
  • 19-01-005H-1 - ENGINE AND ENGINE COOLING: The warranty coverage for the engine long block has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
  • 19-01-006H-4 - ENGINE AND ENGINE COOLING: Applicable vehicles with 2.0l turbo and 2.4l gdi engines may experience the check engine warning lamp illuminated with dtc P1326. Follow the procedure to inspect the vehicle and install a wire harness extension and/or replacement engine bas
  • 19-01-002H-4 - ENGINE AND ENGINE COOLING: Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the malfunction
  • Campaign 953 Dea - ENGINE AND ENGINE COOLING: Hyundai has developed a new engine monitoring technology called a knock sensor detection system (ksds). The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an
  • Campaign T3G Dea - ENGINE AND ENGINE COOLING: Hyundai has launched a service campaign for applicable vehicles with 2.0l turbo and 2.4l gdi engines that may experience the check engine warning lamp illuminated with dtc P132600.
  • 19-GI-006H - EQUIPMENT ADAPTIVE/MOBILITY: This bulletin provides instruction detailing the proper methodology for scanning and uploading captured gds data files to the techline repository. Compliance with this bulletin ensures that the gds data files are correctly transferred and m
  • 19-AT-016H - EQUIPMENT ADAPTIVE/MOBILITY: If you are servicing an applicable vehicle with a ?Check engine? Light on and one or more of the dtc listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
  • 19-AT-012H - POWER TRAIN: This tsb provides a procedure to diagnose and repair a transaxle for the following incorrect ratio dtc (transaxle clutch slipping more than 200 rpm in gear).
  • 19-AT-010H - POWER TRAIN:AUTOMATIC TRANSMISSION: This bulletin provides a procedure to transfer pressure data to the ecu/tcu using gds mobile. This procedure is necessary to reduce the tcu learning time and improve the shift quality.
  • Dealer Best Prac - ELECTRICAL SYSTEM:SOFTWARE: Hyundai has launched a service campaign to update the ecm (engine control module) software for dtc P0128: coolant thermostat (coolant temp below thermostat regulating temperature) logic improvement.
  • DCS T3T - ELECTRICAL SYSTEM:SOFTWARE: Hyundai motor america is conducting a service campaign to update the ecm software on certain 2018 model year elantra gt and 2019 veloster vehicles equipped with 1.6l turbo engines. Service campaign t3t provides a procedure to update the
  • 19-01-016H - ENGINE AND ENGINE COOLING: This bulletin provides information related to an ecm (engine control module) software update for dtc P0128: coolant thermostat (coolant temp below thermostat regulating temperature) logic revision.
  • 19-ST-001H - STEERING: This bulletin provides information regarding replacement of the column-mounted motor driven power steering (mdps) system as separate components.
  • 19-FL-003H - ELECTRICAL SYSTEM: This bulletin provides the procedure to write the vehicle identification number (vin) during the replacement of the engine control module (ecm) or powertrain control module (pcm). Once the vin has been programmed to the ecm/pcm, it cannot b
  • 19-BE-004H - VISIBILITY:REARVIEW MIRRORS/DEVICES: This bulletin provides information on the serviceable parts for the outside mirror assembly. When diagnosing and repairing the outside mirror, do not replace the entire assembly. Refer to page 2 of this tsb for replacement of individual par
  • 19-FL-001H - FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS: In a gasoline direct injection (gdi) engine, highly pressurized gasoline is injected via a common rail fuel line and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional multi-p
  • 19-BE-003H - ELECTRICAL SYSTEM: Some vehicles equipped with the wireless charging pad may experience a no charging condition. This bulletin provides information of how to diagnose the no charging condition.
  • T3Q Dealer Best - EQUIPMENT:ELECTRICAL: Hyundai has launched a service campaign to update the display audio (d-audio) system software on certain 2019 model year veloster (js). This software update corrects a condition where blue link remote services do not process.
  • 19-01-007H - EQUIPMENT:ELECTRICAL: This bulletin describes the procedure for updating the display audio (d-audio) system software on certain 2019 model year veloster (js). This software update corrects a condition where blue link remote services does not process.
  • DCS T3Q - EQUIPMENT:ELECTRICAL: Hyundai motor america is conducting a service campaign to update the display audio software on certain 2019 veloster vehicles. Service campaign t3q provides a procedure to update the display audio software for blank home screen.
  • 5NP-W8Q4G-01 - ELECTRICAL SYSTEM: Hyundai motor america is conducting a service campaign to variant code the front view camera to turn on the high beam assist feature on certain 2019 model year veloster vehicles. Service campaign t3l provides a procedure to activate the hig
  • 5NP-K6K9T-01 - LANE DEPARTURE: SENSING SYSTEM: CAMERA: Some 2019 veloster (js) vehicles equipped with high beam assist (hba) feature may not function. This bulletin provides the service procedure to variant code the front view camera to turn on the high beam assist (hba) feature.
  • 5NP-K5Q4Y-12 - EQUIPMENT: Hyundai motor america is conducting service campaign toto repair the noise from the headlining assist handle on certain 2019 veloster vehicles. Service campaign t3i provides a service procedure to repair the noise from the assist handle are
  • 5NP-Y4C4C-12 - EQUIPMENT: On certain 2019my veloster (js) vehicles, the headlining assist handle on the passenger side may exhibit noise. Follow the procedure outlined in this bulletin to repair the noise from the assist handle area.
  • 5NP-S7S7W-10 - EQUIPMENT ADAPTIVE/MOBILITY: Hyundai motor america is conducting a service campaign to replace the luggage covering shelf dampers on certain 2019 veloster vehicles. Service campaign t3e provides a service procedure to replace the luggage covering shelf dampers.
  • 5NP-C4B6K-10 - EQUIPMENT ADAPTIVE/MOBILITY: On certain 2019my veloster (js) vehicles, the luggage covering shelf damper may exhibit discoloration. Follow the procedure outlined in this bulletin to replace the luggage covering shelf damper..

OBD-II Error Codes

Common OBD Error codes specific to this vehicle.

  • P1326 [17] Knock control, cylinder 1 - control limit reached
  • P0128 [5] Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)
  • P0300 [2] Random/Multiple Cylinder Misfire Detected
  • P0304 [2] Cylinder 4 Misfire Detected
  • P0880 [1] TCM Power Input Signal
  • P0705 [1] Transmission Range Sensor A Circuit malfunction (PRNDL Input)
  • P0706 [1] Transmission Range Sensor A Circuit Range/Performance
Most Recent Consumer Complaints and Accidents
CrashFireTowedInjuredDeathsFailure
Date
NoNoN NoneNone20201202

The vehicles driver's side door handle does not work on the outside in cold weather, the car has to be entered from the passenger side door and opened from the inside. Car is parked and unlocked but outer door handle, on the drivers door, refuses to operate correctly.

NoNoN NoneNone20201201

Vehicles hvac blower motor makes a high pitched squeal/whine when being used on lower fan settings. The bearings in the motor seem to not be properly oiled and creates a sometimes loud sound when being used do to the scraping in the motor head. This is worsened when on rough terrain, the squealing/whining will become worse and more persistent.

NoNoN NoneNone20201201

The vehicles driver's side door handle does not work on the outside in cold weather, the car has to be entered from the passenger side door and opened from the inside. Car is parked and unlocked but outer door handle, on the drivers door, refuses to operate correctly.

NoNoN NoneNone20201201

Vehicles hvac blower motor makes a high pitched squeal/whine when being used on lower fan settings. The bearings in the motor seem to not be properly oiled and creates a sometimes loud sound when being used do to the scraping in the motor head. This is worsened when on rough terrain, the squealing/whining will become worse and more persistent.

NoNoN NoneNone20201130

Vehicles hvac blower motor makes a high pitched squeal/whine when being used on lower fan settings. The bearings in the motor seem to not be properly oiled and creates a sometimes loud sound when being used do to the scraping in the motor head. This is worsened when on rough terrain, the squealing/whining will become worse and more persistent.

NoNoN NoneNone20200119

Drivers side door will not open from the outside. Driver must enter the passenger side and open the driver's door from inside.

NoNoN NoneNone20200118

Drivers side door will not open from the outside. Driver must enter the passenger side and open the driver's door from inside.

NoNoN NoneNone20200115

Drivers side door will not open from the outside in cold (freezing or below) temperatures. It seems to still be locked, despite unlocking the car and being able to open all other doors on the car. Must be opened from the inside through the passenger door.

NoNoN NoneNone20200114

Drivers side door will not open from the outside in cold (freezing or below) temperatures. It seems to still be locked, despite unlocking the car and being able to open all other doors on the car. Must be opened from the inside through the passenger door.

NoNoN NoneNone20191218

Driver's door will not open/unlatch from the outside in cold weather, i.E., below 35 degrees, locked or unlocked. The car was stationary, parked, twice in the driveway, twice away from the house in a parking lot. This just started happening but happens now each time the temperature drops overnight. There are many similar complaints online with no solution.

NoNoN NoneNone20191201

In temperatures below 35 degrees, the drivers door does not open. It clearly makes an unlocking sound when unlock is activated, but the handle acts as if it is locked. I have to crawl through another door to open it from the inside. Only the driver side door is effected, and it opens as normal from the inside. Happens regardless of whether the vehicle is on or off. Obviously stationary.

NoNoN NoneNone20191130

In temperatures below 35 degrees, the drivers door does not open. It clearly makes an unlocking sound when unlock is activated, but the handle acts as if it is locked. I have to crawl through another door to open it from the inside. Only the driver side door is effected, and it opens as normal from the inside. Happens regardless of whether the vehicle is on or off. Obviously stationary.

NoNoN NoneNone20191009

When entering an intersection, my collision avoidance system engaged and abruptly stopped the car in the middle of the intersection. There were several cars that had been in front of me turning to the right but were well ahead of me. The only other car was on the opposite side of the intersection sitting at a stop heading in the other direction. There was a strong sun glare but other than that it was a perfect day. I was traveling at approx 30 mph on a 2 lane road.

CrashNoN 2 InjuredNone20191008

My airbags did not deploy when the vehicle was hit in the front end. The car was a total loss (21 thousand in damage to the front end).

NoNoN NoneNone20190913

The vehicle clutch disc delaminated and exploded while driving the vehicle. The pressure plate, clutch cylinder and several hydraulic parts were also damaged. This also caused the brakes to stop working since the clutch and brakes share a reservoir.

NoNoN NoneNone20190912

The vehicle clutch disc delaminated and exploded while driving the vehicle. The pressure plate, clutch cylinder and several hydraulic parts were also damaged. This also caused the brakes to stop working since the clutch and brakes share a reservoir.

NoNoN NoneNone20190827

The rear hatch window shattered suddenly when closing the driver's door. Vehicle was stationary in driveway. There was no previous damage to the rear hatch window.

NoNoN NoneNone20190603

During startup. When car is first ignition, while in neutral proceed to 1st gear an audible sound will be heard from right column and disappears. It will happen every start up sequence. I sent my car for service and they told me that it could be the electronic differential lock.

NoNoN NoneNone20190602

During startup. When car is first ignition, while in neutral proceed to 1st gear an audible sound will be heard from right column and disappears. It will happen every start up sequence. I sent my car for service and they told me that it could be the electronic differential lock.

NoNoN NoneNone20190409

On may 7th my car was completely dead when i tried to turn it on on the park lot of my work. Wouldn't turn on, no lights, doors wouldn't open or close. Car was jumped by the tow driver and when go to the dealership they couldn't not identify the problem nor could hyundai. The tow driver told them the car was complete dead and still they gave me back the car saying nothing was wrong with it. But a about a month ago the car stalled and went completely off when i was driving on a highway 95 in miami, fl. At first i thought it could have been a human while sifting gears but now i know it wasn't. But after experiencing it a second time i know for sure it wasn't human error. Something is very wrong with this car and hyundai have not been gable to find out what. At the event at the highway i was only able to bring the car back running by snapping the clutch and the gas. If it was an automatic car for sure that would have caused a big accident. After the last time the car died it took half a tank of gas to drive less than 30 miles. Hyundai, is sending the car home to me even though they haven't found anything wrong with yet. They are putting a "black box" for me to record the car engine activities as it happens. I feel scared and unsafe driving this car. It is such a serious matter that i want to share in case someone else experiences that same thing and i wan to make sure my struggle with this car is well known and hopefully will inspire some more investigation.

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.