Volvo Vnm 2007

• Recall 97117 [USA]: Without a signal to disengage the clutch when the brakes are applied, the distance required to stop the truck may lengthen, increasing the risk of a crash.
  Volvo trucks north america (volvo) is recalling certain model year 2007-2014 vah, vhd, vnl, vnm, and vt models. The affected vehicles were built without a redundant clutch disengagement switch. Without a redundant switch, a loss of signal from the brake air pressure switch can prevent the clutch from automatically disengaging when the brake is applied.
  volvo trucks will notify owners and dealers will inspect and repair the vehicles if necessary. The recall began on august 26, 2013. Volvo's recall number is rvxx1303. Owners may contact volvo at 1-336-393-2000.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 67655 [USA]: If this happens a short circuit may occur, which over time could possibly lead to a vehicle fire.
  Volvo trucks is recalling 127,764 my 2001-2008 vhd, vnl, vnm, and my 2005-2008 vt trucks. A seal may fail allowing water and contaminants to seep into the windshield wiper motor.
  volvo will replace the wiper motor free of charge. Since this recall involves a large number of vehicles, volvo will release the recall in stages as parts are received. Priority will be given to the vehicles located in the regions/states that have a corrosive environment. The recall began on september 30, 2009. Owners may contact volvo trucks at 1-800-528-6586.
  volvo trucks recall no. Rvxx0902.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 74792 [USA]: If a short circuit occurs and is left untreated, components and wiring may be subject to overheating which could possibly result in a vehicle fire.
  On certain heavy duty trucks, the circuit protection (i.E. Automatic circuit breakers) used to protect the vehicle lighting system may not provide adequate protection.
  dealers will replace the circuit breakers with fuses. The recall began on february 25, 2008. Owners may contact volvo trucks at 1-800-528-6586.
  volvo trucks recall no. Rvxx0707.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 71849 [USA]: There is a possibility that the pivot bolt can become loose without the driver's knowledge. when this occurs, the driver could drive away and the trailer could become disengaged, increasing the risk of a crash.
  On certain trucks equipped with a saf holland simplex fifth wheel, the lever arm pivot bolt may have been over tightened. An over tightened pivot bolt can distort the pivot bolt spacer sleeve, which may prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin.
  dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer free of charge. The recall began on january 28, 2008. Owners may contact volvo trucks at 1-800-528-6586.
  volvo trucks recall no. Rvxx0705.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 88919 [USA]: If the condition exists and the key is left on without fuel in the filter, the heating element may heat to a point where a flame becomes present at the tip of the element which could result in a vehicle fire.
  On certain trucks, an unprotected lead in the thermoswitch of the heater may make contact with another post possibly creating a short circuit, which can result in continuous operation of the heating element.
  dealers will inspect the thermoswitch and will replace it if necessary. The recall began on september 10, 2007. Owners may contact volvo trucks at 1-800-528-6586.
  volvo truck recall no. Rvxx0703.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 32200 [USA]: If the nut were to come loose, the steering shaft could potentially separate resulting in loss of steering control which could cause a crash.
  On certain trucks, the nut used to retain the steering shaft may or may not be a lock nut that has the locking feature. A lock nut is required to provide additional resistance to ensure that the nut does not come loose.
  dealers will replace the steering shaft pinch bolts and locknuts free of charge. The recall began on august 24, 2007. Owners may contact volvo trucks at 1-800-528-6586.
  volvo recall no. Rvxx0702.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 33084 [USA]: If a fatigue failure occurs and is left unattended, the axle may lock up or the end of the axle could come off, which may result in a vehicle crash.
  On certain trucks, the axle housings may have been manufactured with steel that was out of specification which could result in a fatigue failure over time.
  dealers will repair and inspect the axles and replace them free of charge. The recall began on april 9, 2007. Owners may contact volvo trucks at 1-800-528-6586.
  volvo trucks recall no. Rvxx0701.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 37008 [USA]: This could result in additional damage to the driveline, the vehicle to which it is attached and ay additional nearby objects.
  On certain trucks equipped with arvinmeritor rpl20 high angle interaxle driveshafts, an improper seated or missing snap ring can result in the bearing cup to separate from the slip yoke sub-assembly. The universal joint cross could then contact the slip yoke casting and eventually cause the ear work to fracture.
  dealers will inspect the driveshafts and replace them as needed. The recall began on october 23, 2006. Owners may contact volvo trucks at 1-800-528-6586.
  volvo truck recall no. Rvxx0605.Customers can also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 2013221 [Canada]: Other
  On certain vehicles, the secondary clutch disengagement switch may have been omitted during vehicle assembly or, in some instances, removed during servicing. As such, primary switch failure would cause the automated manual transmission’s clutch to remain engaged when the brakes are applied. This could increase stopping distances, possibly resulting in a crash causing property damage and/or personal injury. Correction: dealers will install a micro-switch at the brake pedal and update the software to run a diagnostic on the switch during engine start-up.

  Show Content

• Recall 2009144 [Canada]: Other
  On certain vehicles, the windshield wiper motor may be susceptible to water intrusion, which could result in an electrical short circuit and a fire. This could cause property damage, personal injury or death. Correction: dealers will affect repairs.

  Show Content

• Recall 2007084 [Canada]: Other
  On certain trucks, the axle housing may have been manufactured with steel that was out of specification (9.5mm thick instead of 11mm thick), which could result in a fatigue failure over time. If failure occurs, the axle may lock-up or the end of the axle could come off, which may result in a vehicle crash with injury or death. Correction: dealers will inspect and, if required, replace the axles.

  Show Content

• Recall 2007253 [Canada]: Steering
  On certain trucks, the locknut used to retain the steering shaft may not have had the lock feature. As a result, the nut could loosen, allowing the steering shaft to separate, causing a loss of steering control which could result in a vehicle crash with injury or death. Correction: dealers will replace the steering shaft pinch bolt and locknut.

  Show Content

• Recall 2007257 [Canada]: Fuel supply
  On certain trucks, when the ignition key is in the 'on' position, the pre-heater, located in the fuel filter base, is energized. If this pre-heater is energized while maintenance is being performed on the fuel filter, diesel fuel could ignite within the filter housing. A fire within the fuel filter housing may spread possibly resulting in property damage or personal injury. Correction: dealers will inspect and, if required, replace the fuel heater assembly.

  Show Content

• Recall 2007338 [Canada]: Other
  On certain trucks, the fifth wheel hitch assembly's lever arm may have been incorrectly installed during the manufacturing process. The lever arm pivot bolt may have been over-tightened which could distort the pivot bolt spacer sleeve and prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin. This could allow the towed unit to separate from the towing vehicle while underway, potentially causing a crash with injury or death. Correction: dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer.

  Show Content

• Recall 2007394 [Canada]: Electrical
  On certain trucks, the automatic circuit breakers used to protect the vehicle lighting system may not provide adequate protection. If a short circuit occurs, components and wiring may be subject to overheating, which could result in a vehicle fire, causing property damage and/or personal injury or death. Correction: dealers will replace the circuit breakers with fuses.

  Show Content

• Recall 2006243 [Canada]: Powertrain
  On certain trucks, an improperly seated or missing u-joint snap ring can result in the bearing cup to separate from the slip yoke sub-assembly. The u-joint could then contact the slip yoke casting and eventually cause the ear to fracture. This could result in additional damage to the driveline, the vehicle and any nearby objects. Correction: dealers will inspect and, if required, replace the driveshafts.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Stop lamp switch signal investigation # PE13002

  The office of defects investigation (odi) received early warning reporting (ewr) data from the manufacturer that indicated some number of subject vehicles equipped with the subject automated manual transmission had allegedly experienced a condition where the clutch failed to automatically disengage the transmission from the engine as intended. This may result in extended stopping distances and/or unintended forward motion of a vehicle previously at rest.To date, odi is aware of 134 subject vehicles with one or more complaints or field reports related to this condition.Also, odi is aware of 164 subject vehicles with one or more warranty claims related to this condition.By letter dated june 25, 2013, volvo trucks north america (volvo) notified odi that it has initiated a safety recall (nhtsa recall no. 13v268 and volvo recall no. Rvxx1303) to address a safety defect in approximately 23,003 model year (my) 2007 through 2014 volvo vah, vhd, vnl, vnm and vt model trucks. The affected vehicles were manufactured from december 20, 2006 through may 22, 2013 and were originally equipped with the subject automated manual transmissions.According to volvo, reports of the subject transmission clutch mechanism failing to automatically disengage as intended are associated with the removal of a brake pedal micro switch that provided a redundant signal to the transmission control module indicating the brakes had been applied.Previously, volvo had removed this brake pedal micro switch from new vehicle production and from certain vehicles already in-service via two field service campaigns (sp 432-024 and sp 432-026) because it decided the switch was unnecessary and/or a maintenance issue.In the absence of this redundant brake pedal micro switch, the clutch mechanism may fail to disengage the transmission from the engine at low vehicle speed should the stop lamp switch fail to send and/or the transmission control module fail to receive the primary signal.At the time of this closing, volvo is evaluating available remedies and will provide nhtsa with details when the recall remedy procedure has been finalized.Volvo will notify affected owners by mail by august 25, 2013.Please see nhtsa recall no. 13v268 for details.Accordingly, this investigation is closed.
  

  Show Content

• Volvo sleeper glass de-bonding investigation # RQ11001

  Odi opened recall query rq11-001 after a review of ewr field reports identified lower bunk window separations on the subject vehicles.Volvo had issued three recalls for sleeper window separations since 2003.Additionally, volvo had issued two bulletins for sleeper window issues during the same time period.The frequency of related actions led odi to open this formal investigation.An information request (ir) letter was sent to volvo on 23 june 2011.Volvo responded on 17 august 2011 and then provided updated warranty information on 9 january 2012.Volvo provided production change data and warranty information which was correlated to vehicle build month and failure date.Odi analyzed the data to determine if additional production time frames should have been included in previous recalls.Odi also requested information from its network of fleet owners.The response from this network reaffirmed the accuracy of the updated warranty information.Based on the information and data received, odi has concluded that all production periods have been appropriately addressed by volvos previous recalls and no additional recall action is required at this time.
  

  Show Content

• Saf holland fifth wheel assembly investigation # PE07046

  On october 18, 2007 volvo trucks north america filed defect report 07v-496 which outlines a safety recall program to notify the affected owners and correct the affected vehicles.
  

  Show Content

Tl* contact owns a 2007 volvo vnm670. The contact stated that the vehicle was involved in a crashed and the air bags failed to deploy. The driver sustained minor injuries. A police report was filed. The dealer was made aware of the failure. The manufacturer was not notified of the failure. The vehicle was destroyed. The vin was not available. The failure and current mileage was 450,000.

Consumer writes in regards to two head on collisions and problem with airbag deployment *tgw the consumer stated the collisions involved two different volvo tractors.

I was driving a 2007 volvo vnm for yrcw trucking co. I did all the appropriate safety checks and after 140 miles driving,when i slowed to 5mph to pass through the ezpass lane at lakawana ny, the fifth wheel released and dropped the trailers in the roadway. Somehow the air release was activated and opened the fifth wheel jaws of the fifth wheel. *tr

2007 volvo vnm conventional stalled on the highway. *bf when the truck stalled, the driver panicked and abruptly turned his vehicle and stuck the lane extender. Ohio traffic crash report # 10-0289-91 updated 05/03/10 *bf

Common OBD-II Error Codes

• U0121 [1] Lost Communication With Anti-Lock Brake System (ABS) Control Module
• P0420 [1] Catalyst System Efficiency Below Threshold (Bank 1)
• P111C [1] P111C
• P040A [1] Exhaust Gas Recirculation Temperature Sensor "A" Circuit
• P040B [1] Exhaust Gas Recirculation Temperature Sensor "A" Circuit Range/Performance
• P1121 [1] Engine Coolant sensor out of range/ECT Sensor Out Of Self Test Range
• P009E [2] Fuel Pressure Relief Control Performance/Stuck Off
• P208E [1] Reductant Injection Valve Stuck Closed Bank 1 Unit 1
• P103B [1] P103B
• P2459 [2] Diesel Particulate Filter Regeneration Frequency
• P0194 [1] Fuel Rail Pressure Sensor A Circuit Intermittent
• P249F [1] Excessive time to enter closed loop Diesel particulate filter (DPF) regeneration control
• P24A0 [1] Closed loop Diesel particulate filter (DPF) regeneration control, control limit reached – temperature too low
• P226C [1] ISO/SAE Reserved
• P2002 [1] Diesel Particulate Filter Efficiency Below Threshold Bank 1
• P24A4 [1] P24A4
• P10FE [1] P10FE
• P249C [1] Excessive time to enter closed loop reductant injection control
• P0422 [1] Main Catalyst Efficiency Below Threshold (Bank 1)