PIC5588D
Service Bulletin Details
Public Details for: PIC5588D
This preliminary information communication provides information to the technician on the programming and activation of the onstar system. For many 2008 and prior model year gm vehicles, the programming is performed using the tech 2 and the
- 2018 - 2017 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 - 2010 - 2009 - 2008 - 2007 - 2006 - 2005 - 2004 - 2003 - 2002 - 2001 - 2000 -
Models from 2018
Models from 2017
Models from 2016
Models from 2015
Models from 2014
Models from 2013
Models from 2012
Models from 2011
Models from 2010
Models from 2009
Models from 2008
Models from 2007
Models from 2006
Models from 2005
Models from 2004
Models from 2003
Models from 2002
Models from 2001
Models from 2000
Bulletin No.: PIC5588D Published date: 06/12/2017 Preliminary Information PIC5588D Programming And Activation Of Replacement OnStar Modules (VCIM) Models Brand: All Model: All VIN: Model Years: 2000 - 2018 from All Engine: to All All Transmissions: All This PI applies to vehicles with RPO UE1. Note: This PI does not apply to Canada upgrade vehicles. Supersession Statement: This PI was superseded to add an important notice to connect to OnStar after programming to verify activation status, and added 18 Model Year. Please Discard PIC5588C. The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI. Condition / Concern The Vehicle Communication Interface Module (VCIM) is part of the OnStar system and interacts with several other electronic control devices in the vehicle. In order for OnStar to operate properly, it must be programmed (set-up) specifically for the vehicle application to which it’s been installed. In addition to the setting up of the unit for the vehicle, the replacement unit must be activated by OnStar in order for the customer to receive his or her subscription services. There are two procedures to follow in order to complete the module set-up and activation. Recommendations / Instructions For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System (SPS) application called OnStar Activation (ONSA in the supported Controller selection menu). This OnStar Activation procedure gathers critical information from the replacement unit and sends this data to OnStar. This data is then used to update the subscriber’s account and to activate the unit according to the subscriber’s vehicle and account settings. When using the ONSA procedure, a blue button press is no longer needed for activation of the OnStar replacement unit. The auto-activation is generally completed within 2 hours or less. In many instances (depending on the cellular market and subscribers home address), the subscribers personal calling phone number (My Number) remains unchanged and is transferred to the replacement unit. For many 2009 model year vehicles, the OnStar or VCIM set-up procedure has moved from the Tech 2 to the SPS application. This set-up is now similar to that of many other body control modules. This change provides a more efficient process where both the programming and activation procedures are now supported by the Techline SPS application. These two procedures are denoted as the VCIM Vehicle Communication Interface Module Set-up and the ONSA-OnStar Activation. Important: To fully activate an OnStar module, both the set-up and activation request procedures must be completed. To initialize the Turn-by-Turn feature, the vehicle must first be driven 8-10 km (5 mi) in order to allow the system to self-calibrate the dead reckoning feature. Important: Use of a J2534 compatible diagnostic tool interface is required when performing the SPS supported OnStar (VCIM) set-up and Activation (ONSA) procedures. For the 2010 and UP model year vehicles, the OnStar (VCIM) set-up procedure and OnStar Activation (ONSA) request have been combined into a single programming event called OnStar Set-up and Activation (ONSU). This change provides the most efficient process to complete all of the required steps to fully activate the replacement unit, thereby eliminating any button press and long in-vehicle wait times for the activation to be completed by an OnStar advisor. IMPORTANT: **** Prior to releasing the vehicle**** Once all SPS events have been completed, it is neccessary to wait 10 minutes and then test operation to confirm the module has been properly setup and the account is now active. If OnStar requests the vin or says they do not have vehicle info with the call, this would indicate that the activation did not go through and OnStar will need to perform a configuration for manual hardware replacement The table below provides a quick reference as to the steps/tools to use for the listed model years: VCIM Set-Up OnStar. Activation Combined Set-Up and Activation GM Passenger Cars and Trucks (Including Saturn) Tech 2 SPS N/A 2004-2008 HUMMER H2 (All Models) Tech 2 SPS N/A 2004-2008 HUMMER H3 (All Models) Tech 2 SPS N/A Digitally Upgraded GM Passenger Cars and 2000-2005 Trucks (Including Saturn) Tech 2 SPS N/A SPS SPS N/A Model Year Vehicle Type(s) 2004-2008 2009 GM Passenger Cars and Trucks (Including Saturn) Except When Noted Below 2009 Chevrolet Uplander/Pontiac Tech 2 Montana SV6 SPS N/A 2009 Chevrolet Cobalt/Pontiac G5 Tech 2 w/o RPO UPF SPS N/A SPS SPS N/A 2009 Chevrolet Cobalt/Pontiac G5 w/RPO UPF 2009 HUMMER H2 (All Models) SPS SPS N/A 2009 HUMMER H3 (All Models) SPS SPS N/A 2010 and UP GM Passenger Cars and Trucks N/A N/A SPS Warranty Information For vehicles repaired under warranty, please refer to the latest version of bulletin 06-08-47-001 for warranty information on control module reset/configuration. Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed. © 2016 General Motors. All Rights Reserved.