Mazda Mazda6 2006

• Recall 146147 [USA]: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
  Mazda north american operations (mazda) is recalling certain 2003-2008 mazda6, 2004-2005 mpv, 2004 rx-8, and 2006-2007 mazdaspeed6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
  mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began december 3, 2019. Owners may contact mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 2618f. Note: this recall supersedes recalls 13v130, 14v362, 14v773 and 15v869.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 124344 [USA]: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
  Mazda north american operations (mazda) is recalling certain model year 2003-2008 mazda6, 2004-2008 rx-8, and 2006-2007 mazdaspeed6 vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion and other factors, including manufacturing variability that, over time, could cause the inflator to rupture.
  mazda will notify owners, and dealers will replace the driver's frontal air bag inflator with an alternate inflator, free of charge. The recall began on september 12, 2017. Owners may contact mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1417g. Note: this recall supersedes recall 15v-382.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 85920 [USA]: Decreased lighting visibility may result in a vehicle crash.
  Dope, inc. Is recalling 42,540 combination corner and bumper lamp assemblies of various part numbers sold for use as aftermarket equipment for various passenger vehicles. These headlamps fail to conform to the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment." these lamps do not contain the required amber side reflectors.
  dope, inc. Will notify owners and offer a full refund for the noncompliant combination lamps. The safety recall began on july 28, 2009. Owners may contact dope, inc. At 1-626-272-1798.
  this recall only pertains to aftermarket replacement equipment and has no relation to any original equipment installed on vehicles produced by the vehicle manufacturer.In order to determine if your aftermarket lamp assembly is affected by this noncompliance, please review the list of model numbers provided to us by dope, inc.The list can be found under "document search" located at the bottom of your screen. Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 84539 [USA]: This may result in the bolt(s) snapping off during use or without a load. the unsecured rack and load can then come loose while driving creating a potential road hazard, possibly resulting in a vehicle crash.
  Thule, inc. Is recalling 2,323 owner-installed roof-mounted fit kits, models 3068 and 3069, manufactured between january 1, 2008 and february 28, 2009 that are used with thule podium foot packs, models 460 and 460r. These fit kits were sold as aftermarket equipment for use on the vehicles listed above. The bolt(s) used to secure the foot to the vehicle was manufactured to a hardness that may cause the bolt(s) to be brittle and potentially break under stress.
  thule will mail a retro fit kit along with repair instructions to owners free of charge. The safety recall is expected to begin on or before april 13, 2009. Owners may contact thule toll-free at 1-800-238-2388.
  this recall only pertains to thule aftermarket roof mounted load carriers and has no relation to any original equipment installed on the listed passenger vehicles.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall R/2008/194 [UK]: Engine revs may increase inadvertently
  It is possible that white smoke can occur from the exhaust pipe and engine speed may increase whilst driving.
  recall affected vehicles and replace power control module.

  Show Content

• Recall R/2017/048 [UK]: Airbag may malfunction
  It has been identified that the density of the propellant within the airbag inflator may be insufficient due to inappropriate production and storage conditions of the propellant. In this condition the inflator may abnormally ignite at the time of the airbag deployment allowing the inner pressure of the inflator to increase abnormally resulting in the breakage of the inflator case. In this condition the airbags will not provide adequate protection during a frontal impact as the broken pieces of the inflator case could injure the driver and/or front seat passenger.
  recall all affected vehicles to replace the driver and passenger front airbag inflators with modified units.

  Show Content

• Recall R/2018/184 [UK]: Airbag inflators may not operate as intended
  On the subject vehicles the takata driver and passenger airbag inflators may not operate as intended injury may result due to incorrect deployment of the airbag
  replacement of airbag assembly

  Show Content

• Recall R/2021/411 [UK]: Fuel may leak from fuel pump rings
  Fuel may leak from fuel pump rings.
  replace the fuel pump rings with new ones.

  Show Content

• Recall R/2018/284 [UK]: Takata driver and passenger airbag inflators may not operate as intended
  Driver and passenger airbag inflators may not operate as intended.
  replacement of airbag assembly.

  Show Content

• Recall 2018578 [Canada]: Airbag
  On certain vehicles, the passenger frontal airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the passenger airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of injury to the seat occupant. Correction: dealers will replace the passenger frontal airbag inflator. Note: this recall supersedes recalls 2013-112 (mazda recall 6913d), 2014-245 (mazda recall 7714f), 2015-624 (mazda recall 9015l), 2016-259 (mazda recall 9416e) and 2017-011 (mazda recall 0617a).

  Show Content

• Recall 2018036 [Canada]: Airbag
  On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, could eventually degrade the propellant contained in the driver frontal airbag. This could cause the airbag to deploy with more force than normal. As a result, if the vehicle were involved in a collision that warrants airbag deployment, fragments could be propelled toward vehicle occupants, and the airbag assembly could be damaged, preventing proper function. These issues could increase the risk of injury. Correction: dealers will replace the driver frontal airbag inflator. Note: canadian climate results in the propellant degrading slowly. The recall is being conducted as a precaution to address future risk, and is expected to replace airbag inflators before their function would be affected. Additional note: this recall supersedes recall 2015-247 (mazda recall 8215f). Vehicles completed under 2015-247 do not need to be completed under recall 2018-036.

  Show Content

• Recall 2015624 [Canada]: Airbag
  Note: this recall is superseded by recall 2018578 (mazda recall 2618f). Please see recall 2018578 for more information. On certain vehicles, the passenger frontal airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Correction: dealers will replace the passenger airbag inflator.

  Show Content

• Recall 2015247 [Canada]: Airbag
  On certain vehicles, the driver frontal airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Correction: dealers will replace the airbag module. Note: this recall is superseded by recall 2018-036. Please see recall 2018-036 for more information. Click here for more information.

  Show Content

• Recall 2014570 [Canada]: Airbag
  Mazda canada is conducting a voluntary safety improvement campaign concerning the driver's airbag inflator on certain vehicles equipped with takata airbags. Mazda will replace the driver's inflator on affected vehicles. This action is not being conducted under the requirements of the motor vehicle safety act. Note: this safety improvement campaign is superseded by recall 2015-247 (mazda recall 8215f). Please see recall 2015247 for more information.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Desiccated air bag inflator rupture investigation # EA21002

  From 2000 through 2017, takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("psan") propellant -- propellant 2004 and propellant 2004l. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 blomquist report at www.Nhtsa.Gov/sites/nhtsa.Gov/files/documents/expert_report-hrblomquist.Pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in us vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004l that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated psan inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All takata inflators produced with propellant 2004l contain desiccant, and none of these desiccated inflators using propellant 2004l are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated psan inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- takata (now known as tk global), the independent testing coalition, and exponent -- have been studying the long-term behavior of takata desiccated psan inflators using propellant 2004l (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004l is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004l.The office of defects investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated psan frontal inflators manufactured by takata. This investigation will require extensive information on takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated psan inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.Gov/recalls?Nhtsaid=ea21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede ea15-001, which remains open.
  

  Show Content

• Air bag inflator rupture investigation # EA15001

  The office of defects investigation (odi) opened pe14-016 in june 2014 based on six inflator rupture incidents involving consumer owned vehicles produced by five vehicle manufacturers.All six vehicles were operated in florida or puerto rico at the time of the rupture and for the majority of their service life, and were equipped with inflators produced by takata, a tier-one supplier of automotive air bag systems.During the course of pe14-016, odi determined that five additional vehicle manufacturers used inflators of a similar design and vintage also supplied by takata. No evidence of field failures was found in vehicles produced by these five additional manufacturers.Nonetheless, at odis insistence, all 10 vehicle manufacturers initiated a regional recall within approximately two weeks of the opening of the investigation.The regions recalled initially included florida, puerto rico, hawaii, and the u.S. Virgin islands, areas with high absolute humidity and climatic conditions believed to be a significant factor in the inflator ruptures.As part of the recall actions, inflators removed from remedied vehicles are to be returned to takata for testing.Takatas initial test results on passenger inflators from remedied vehicles indicated a much higher than anticipated rupture frequency for inflators returned from florida.Accordingly odi requested all 10 manufacturers expand the regional recalls for passenger inflators to include other geographic areas where high absolute humidity conditions exist, including the gulf states and other coastal areas.Takatas testing of the passenger inflators to date continues to indicate this geographic area as having the highest risk, with no ruptures occurring from inflators returned from outside the expanded recall regions.During pe14-016 four additional passenger inflator field events occurred, all in vehicles from the same expanded geographic region.Also during pe14-016 four additional driver inflator field events occurred including two in vehicles from regions not known for high absolute humidity, specifically california and north carolina.Accordingly, odi requested all five of the affected vehicle manufacturers currently using the subject takata driver inflators expand to nationwide recalls.Significantly, neither of the affected vehicle manufacturers or takata provided any explanation to account for these two driver air bag inflator ruptures outside the area of high absolute humidity.Takata testing of returned driver inflators indicates a lower rupture frequency as compared to passenger inflator testing.All test ruptures reported by takata to date have occurred on inflators returned from high absolute humidity areas.The investigation now includes all manufacturers and vehicles known to be affected at this time.Odis investigation will focus on, among other things, root cause analysis, other potential defect consequences, identification of affected vehicles scope, and adequacy of the remedy.The five odi reports cited above can be reviewed online at http://www-odi.Nhtsa.Dot.Gov/owners/searchnhtsaid under the following identification numbers: 10537899, 10568848, 10585224, 10605877, 10651492
  

  Show Content

Please can someone put in a recall for this my transmission is having problems again and this is my second madza 6... This doesn't make any sense we spend money of vehicles that suppose to run well... So why are there so many people having problems with these madza's and know one is doing anything about it.... I was on the highway with my kids when the car just cut off and wouldn't move and when it did it was started grinding when i put it in gear.... That was a scary thing... The same happened to me in my first madza 6 with only 89000 miles on it... Something needs to be done....

Please can someone put in a recall for this my transmission is having problems again and this is my second madza 6... This doesn't make any sense we spend money of vehicles that suppose to run well... So why are there so many people having problems with these madza's and know one is doing anything about it.... I was on the highway with my kids when the car just cut off and wouldn't move and when it did it was started grinding when i put it in gear.... That was a scary thing... The same happened to me in my first madza 6 with only 89000 miles on it... Something needs to be done....

Had recall for defective airbags. Took vehicle to dealer and they replaced both drivers side and passenger side air bags. I have received second recall notice to have the passenger side replaced again as the one they originally replaced it with is defective to. If the passenger side is defective then so the drivers side is to. Want to know why drivers side isn't going to be replaced.

Had recall for defective airbags. Took vehicle to dealer and they replaced both drivers side and passenger side air bags. I have received second recall notice to have the passenger side replaced again as the one they originally replaced it with is defective to. If the passenger side is defective then so the drivers side is to. Want to know why drivers side isn't going to be replaced.

I've had issues with my car whenever i put gas in it. My car won't start up or cut off whenever i put gas in it. I've also had issues with the acceleration because of this.

I've had issues with my car whenever i put gas in it. My car won't start up or cut off whenever i put gas in it. I've also had issues with the acceleration because of this.

- vehicle is subject to takata airbag recall. Located in zone a - received multiple notices in mail since 2016. - mazda website does not acknowledge a recall exists when trying to schedule an appointment - they acknowledge it when phoned in - recall always quoted to take a day, with no alternate transport available. Despite mailer saying free alternative transport available. I've tried multiple times. - i need a vehicle - always. Right now my choice is to continue driving my car (at risk of 'serious injury or death') or lose my livelihood.

Front sub-frame rusted causing lower suspension / control arm to come apart, leaving front wheel to be unstable. This happened while driving, almost causing accident do to instability in staring system. I see that this is a common problem with this model, however for some reason my vin doesn't show the recall. Is this something that the company is planning to address, or am a stuck with the problem? Pictures included.

Front sub-frame rusted causing lower suspension / control arm to come apart, leaving front wheel to be unstable. This happened while driving, almost causing accident do to instability in staring system. I see that this is a common problem with this model, however for some reason my vin doesn't show the recall. Is this something that the company is planning to address, or am a stuck with the problem? Pictures included.

Common OBD-II Error Codes

• P0441 [2] Evaporative Emission Control System Incorrect Purge Flow
• P0442 [2] Evaporative Emission Control System Leak Detected (small leak)
• P0455 [2] Evaporative Emission Control System Leak Detected (gross leak)
• P0456 [1] Evaporative Emissions System Small Leak Detected
• P2112 [1] Throttle Actuator Control System - Stuck Closed
• P2006 [1] Intake Manifold Runner Control Stuck Closed Bank 1
• P0106 [1] Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance Problem