Gmc Sierra 1500 Hd 2002

• Recall 85598 [USA]: Decreased lighting visibility may result in a vehicle crash.
  Dope, inc. Is recalling 42,540 combination corner and bumper lamp assemblies of various part numbers sold for use as aftermarket equipment for various passenger vehicles. These headlamps fail to conform to the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment." these lamps do not contain the required amber side reflectors.
  dope, inc. Will notify owners and offer a full refund for the noncompliant combination lamps. The safety recall began on july 28, 2009. Owners may contact dope, inc. At 1-626-272-1798.
  this recall only pertains to aftermarket replacement equipment and has no relation to any original equipment installed on vehicles produced by the vehicle manufacturer.In order to determine if your aftermarket lamp assembly is affected by this noncompliance, please review the list of model numbers provided to us by dope, inc.The list can be found under "document search" located at the bottom of your screen. Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

  Show Content

• Recall 75564 [USA]: Wheel separation can result in a vehicle crash.
  Certain federal-mogul replacement wheel hub assemblies with the brand names: national, carquest p/nos. 515020, 515021, 515025, 515053, 515054, 515059, and 515060, shipped between january 23, 2006, and december 20, 2007, sold for light duty and medium duty trucks. The inboard retention nut used to maintain hub bearing assembly can loosen resulting in an abs light indication, noise, and/or wheel separation.
  federal-mogul will notify customers and will replace the hub assembly free of charge. The recall began on february 7, 2008. Owners can contact federal-mogul toll-free at 877-489-6659.
  this recall only pertains to replacement national, carquest wheel hub assemblies and has no relation to any original equipment installed on vehicles manufactured by general motors or ford.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 72466 [USA]: If the trailer lights are not working properly, a vehicle crash can occur.
  Certain cequent 90 degree 7-way right angle adaptors sold by distributors in tow packages for aftermarket sales to tow 5th wheel rv travel trailers. Due to incorrect wiring of the harness, the trailer lights may not operate properly.
  all of the defective tow packages are still at the distributor level and have not been sold to any consumers.
  this recall only pertains to aftermarket cequent tow packages and has no relation to any original equipment installed on daimlerchrysler, gmc, or ford vehicles.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 60419 [USA]: If stopping distance is limited, a vehicle crash could occur.
  Certain federal-mogul national and carquest aftermarket hub assemblies, p/n 515058, sold for use on 2001-2006 general motors 1500 and 2500 4wd trucks. On the subject hub assemblies, the abs sensor cord departs from the hub assembly at a 90 degree angle. As a result, there is a fit issue with the brake rotor dust shield interfering with the abs sensor cord. If the hub assembly is installed despite this interference, the gap between the abs sensor and the tone wheel may be altered. This may weaken the output of the abs sensor. Diminished output could result in an unwanted abs activation at low speeds and stopping distance could be affected.
  federal-mogul will notify its owners and will either credit the customers account or replace the unit. The recall is expected to begin during june 2006. Owners can contact federal-mogul customer service at 1-800-563-8507 ext 3530.
  this recall only pertains to aftermarket national and carquest hub assemblies and has no relation to any original equipment installed on vehicles manufactured by general motors.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 60186 [USA]: This condition may cause an inadequate seal at the connection, potentially leading to a fuel leak. in the presence of an ignition source, a fire could occur.
  Certain replacement fuel filters, fram brand name p/n g3727, with date codes x52911 through x60801 sequentially or x600141 and a mexico country or origin marking on the fuel filter housing manufactured from october 18, 2005, through march 21, 2006, sold for use on the vehicles listed above and on certain school buses. (to see the school bus engine sizes, click on "document search" and then "bus applications"). The connector on the fuel filter was not manufactured to honeywell's specification. As a result, the o-ring may not seat correctly on the fuel line.
  honeywell will notify owners and replace the fuel filters free of charge. The recall began on october 18, 2006. Owners may contact fram customer service at 1-800-890-2075 (option 1).
  this recall only pertains to aftermarket fram fuel filters and has no relation to any original equipment installed on the vehicles listed.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

  Show Content

• Recall 36296 [USA]: This can cause increased stopping distances during low-speed brake applications, which could result in a crash.
  Certain pickup trucks and sport utility vehicles may experience unwanted antilock brake system (abs) activation. This condition is more likely to occur in environmentally corrosive areas. This recall will be launched in the "salt belt" states of connecticut, delaware, illinois, indiana, iowa, maryland, massachusetts, maine, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, west virginia, wisconsin and the district of columbia only.
  dealers are to remove the wheel speed sensor and thoroughly clean the wheel speed sensor mounting surface on the bearing, apply rust inhibitor to the cleaned surface, grease the mounting surface, reinstall the wheel speed sensor, and check the peak-to-peak output voltage to ensure the wheel speed signal is within specifications. The recall began september 22, 2005. Owners may contact chevrolet at 1-800-630-2438 or gmc at 1-866-996-9463.
  gm recall no. 05068. Gm revised the involved vehicles by amending the original 573 report on october 4, 2005. Gm revised the original 573 report on december 16, 2005, to include additional states and vehicle population.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 55579 [USA]: If the parking brake does not hold, unintended vehicle movement could occur, which could result in a crash.
  On certain pickup trucks equipped with manual transmissions and built with either pbr parking brake systems or trw parking brake systems, the parking brake friction linings may wear to an extent where the parking brake can become ineffective in immobilizing a parked vehicle.
  dealers will install a low-force spring clip retainer for vehicles equipped with a pbr parking brake system. On vehicles equipped with the trw parking brake system, dealers will install a redesigned parking brake cable assembly. The recall began on july 29, 2005. Owners may contact chevrolet at 1-800-630-2438 or gmc at 1-866-996-9463.
  gm recall no. 05042.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

  Show Content

• Recall 55977 [USA]: In the event of a vehicle crash, the wheelchair may not be adequately secured possibly resulting in injuries to a wheelchair occupant.
  On certain vans equipped with sure-lok wheelchair securement systems, the sprocket teeth of the retractor assembly is out of alignment.
  dealers will inspect and replace the wheelchair securement retractors as necessary. Sure-lok will handle the repairs for this campaign. Owners should contact sure-lock at 1-908-231-1804 or mobilityworks at 1-800-769-8267.
  sure-lok recall no. 04e-058.Customers can also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 33771 [USA]: The bedliner can become detached from the pickup while it is motion, possibly endangering following motorists or pedestrians.
  Aftermarket pickup truck over-the-rail bedliners manufactured for installation on 1999-2004 chevrolet silverado and gmc sierra pickup trucks. The toggle wing assembly used to attach the bedliner to the truck bed is not engaging fully in the stake pocket of the pickup truck.
  durakon will issue a press release in attempt to notify customers that could have purchased the defective bedliner. If you purchased either a durakon allstar of patriot overrail bedliner since august 1, 2003, for 1999 to 2004 chevrolet silverado or gmc sierra trucks, or purchased one of these pickup trucks with either brand bedliner already installed, you should return to an authorized durakon dealer so that the bedliner can be inspected and, if necessary, repaired with a newly designed toggle wing fastening system, or if required, replaced with a new bedliner free of charge. Please call the durakon hotline at 1-800-933-4200 to find the nearest authorized durakon dealer.
  this recall only pertains to aftermarket overrail bedliners and has no relation to any original equipment installed on chevrolet silverado and gmc sierra pickup trucks by general motors.Customers can contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 42453 [USA]: Anyone sitting or standing on the horizontal surface of the tailgate when both cables fractured could be injured by falling from the tailgate. on vehicles that have had the bumper removed, the tailgate may drop even lower. additionally, if there is cargo on the tailgate the cargo may fall off if the support cables fracture.
  On certain pickup trucks and sport utility vehicles, the galvanized steel tailgate support cables that retain the tailgate in the full open (horizontal) position may corrode, weaken, and eventually fracture. If both cables fractured, the tailgate would suddenly drop and strike the top surface of the rear bumper.
  dealers will replace the cables. Interim owner notification began on april 7, 20004. The recall began on september 24, 2004, when replacement parts were available, and will continue through october 29, 2004. Owners should contact cadillac at 1-866-982-2339, chevrolet at 1-800-630-2438 or gmc at 1-866-996-9463, or visit www.Mygmlink.Com, and enter your vehicle identification number.
  gm recall no. 04007.Customers can also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 60376 [USA]: A strong odor of natural gas may be detected from inside the vehicle, possibly accompanied by a hissing noise. if the natural gas were accidentally ignited, serious injury could result.
  Some 2wd and 4wd pickup trucks, converted to either dedicated or bi-fuel compressed natural gas (cng) fuel usage, were assembled with a throttle cable that can contact and rub through the flexible pressurized fuel line creating a pinhole leak of natural gas to the atmosphere.
  dealers will secure the throttle cable to eliminate the possibility of contact with the cng fuel line. The cng fuel line, throttle cable, and cruise control cable are also to be inspected and replaced if necessary. Owner notification began on december 11, 2003. Owners should contact chevrolet at 1-800-630-2438 or gmc at 1-866-996-9463.
  gm recall no. 03053.Customers can contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

  Show Content

• Recall 2005116 [Canada]: Brakes
  On certain 1999-2002 1500 series and 2001-2005 2500 & 3500 series trucks equipped with a manual transmission, the parking brake friction lining may wear to an extent where the parking brake can become ineffective in immobilizing a parked vehicle. Correction: dealers will install a low-force spring clip retainer on vehicles equipped with pbr parking brake system and install a redesigned parking brake cable assembly on vehicle equipped with a trw parking brake system.

  Show Content

• Recall 2004102 [Canada]: Other
  On certain vehicles, the galvanized-braided-steel tailgate support cables used to support the tailgate in the full open (horizontal) position can corrode over time and fracture when loads are applied to them. Tailgate support cable corrosion may not be visible because of the plastic sheathing covering the cable. If one cable fractured, the remaining cable may retain the tailgate in a horizontal position. If the remaining cable was weakened by corrosion, it could fracture within moments of the first cable fracture. If both cables fractured, the tailgate would suddenly drop approximately 10 degrees and strike the top surface of the rear bumper. If anyone is sitting or standing on the horizontal surface of the tailgate when both cables fracture, they could fall and be injured. On vehicles without a rear bumper, the tailgate may drop to a lower position. Correction: dealers will replace the existing galvanized support cables with stainless steel support cables.

  Show Content

• Recall 2004395 [Canada]: Brakes
  Certain vehicles located in ontario, quebec, new brunswick, nova scotia, prince edward island, and newfoundland & labrador may experience unwanted antilock brake system (abs) activation and increased stopping distances during low-speed brake application (less than 16 km/h and greater than 6 km/h). This condition does not set any abs codes nor does it illuminate the abs warning lamp. Correction: dealers will remove the wheel speed sensor and thoroughly clean the wheel speed sensor mounting surface on the bearing, apply zinc-x to the cleaned surface, grease the mounting surface, reinstall the wheel speed sensor, and check the output voltage to ensure the wheel speed signal is within specifications.

  Show Content

• Recall 2003292 [Canada]: Fuel supply
  On certain vehicles converted to either dedicated or bi-fuel compressed natural gas (cng) fuel usage, the throttle cable may contact and rub through the flexible pressurized fuel line creating a pinhole leak of natural gas to the atmosphere. A strong odour of natural gas may be detected from inside the vehicle, possibly accompanied by a hissing noise. If the natural gas were accidentally ignited, serious injury could result. Correction: dealer will secure the throttle cable to eliminate the possibility of contact with the cng fuel line. The cng fuel line and throttle cables are also to be inspected and replaced if evidence of wear is found.

  Show Content

• Recall 2002068 [Canada]: Seats and restraints
  Certain vehicles fail to conform to cmvss 209, seat belt assemblies. These vehicles have a condition where one or two sensors in the driver's and front seat passengers seat belt retractors may be inoperative. The seat belt retractors will lock when the belt webbing is extracted during a crash; however the mechanism that locks the seat belt retractor when the vehicle decelerates quickly, such as during heavy braking, may not restrain the occupant as intended during a crash, and could result in injury to the occupant. Correction update: none required as no effect on vehicle safety. See recall 04-158.

  Show Content

• Recall 2001186 [Canada]: Brakes
  Certain 2500 and 3500 pickup trucks equipped with 6.6l diesel engines fail to comply with requirements of c.M.V.S.S. No. 105, "hydraulic and electric brake systems." these vehicles have a brake system warning light in the instrument cluster that may not illuminate when the brake fluid is low. In addition, when the brake fluid is low, the vehicle may not meet the partial system requirements of c.M.V.S.S. No. 105. These conditions could result in reduced braking capability, which could lead to a crash. Correction: dealers will change the location of a wire connection in the underhood bussed electrical center.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Brake line corrosion failure investigation # PE10010

  The office of defects investigation (odi) received defect petition dp10-003 on march 2, 2010, requesting the investigation of model year (my) 2003 chevrolet silverado 2500hd 4wd pickup trucks for corrosion failures of the vehicle brake lines.Dp10-003 was granted and on march 30, 2010, preliminary evaluation pe10-010 was opened on more than six million model year 1999 through 2003 light trucks and sport utility vehicles manufactured and sold by general motors corporation (gm).On july 2, 2010, odi received gms response to an information request, which included gms assessment of the frequency and safety consequences of the alleged defect. Gm stated that:(1) the brake system of the subject vehicles is split front/rear and should a brake pipe suddenly fail for any reason, the affected vehicle would be capable of stopping with the pressure supplied by the remaining circuit; (2) the subject vehicles were designed to meet the hydraulic circuit partial failure requirements of federal motor vehicle safety standards 105 and 135, light vehicle brake systems; and (3) should a brake fluid leak occur for any reason, the brake system malfunction indicator lamp (mil) would illuminate and warn the driver before the brake fluid level was low enough to cause a loss of line pressure.Odis and gms analysis indicates that 85 percent of the complaints occurred on vehicles used primarily in states that use salt on the roads during winter months (connecticut, delaware, district of columbia, illinois, indiana, iowa, maine, maryland, massachusetts, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, west virginia and wisconsin).Overall the complaint rates per 100,000 vehicles for salt belt states is 43.0 and non-salt belt is 3.0.In approximately 25 percent of the complaints the brake pipe failure occurred suddenly, with no warning (i.E., no mil, brake fluid loss warning), and resulted in extended stopping distances.In 30 of these the increase in stopping distance that resulted was a factor in the crash and in 10 others the vehicle was intentionally steered off the road or into another lane of travel in order to avoid a crash.This investigation has been upgraded to an engineering analysis (ea11-001) for subject vehicles sold or currently registered in salt belt states to further assess the scope, frequency and safety risks associated with sudden failures of corroded brake pipes that can result in decreased brake effectiveness. Odi will continue to gather information on subject vehicles outside the salt belt as well.
  

  Show Content

• Crank position sensor failure - stall investigation # PE06016

  The office of defects investigation (odi) opened a preliminary evaluation (pe06-016) on may 4, 2006 based on eleven vehicle owner questionnaires (voqs) and early warning (ewr) data alleging sudden engine shutdown while driving as a result of crank position sensor failures in my 2001-2002 general motors c/k platform vehicles equipped with 8.1l engines.In response to an information request letter sent by odi, general motors (gm) provided owner complaint information, field reports and warranty claim data based on a population of 108,338 vehicles. The data was categorized by engine stalls while driving, engine stalls with an unknown driving condition, no start conditions and claims where it was indeterminate if an engine stall occurred while driving.General motors response included 1,213 owner complaints and field reports of which 289 were categorized as engine stalls while driving allegedly caused by crank position sensor failures. General motors also submitted warranty claims from its regular warranty (5 years/50,000 miles) and from its extended warranty database. From the regular warranty database there were 3,140 claims of crank position sensor replacement of which 147 claims were from consumers alleging engine stall while driving.Gm stated that 2,841 of the claims were indeterminate if an engine stall occurred while driving.From its extended warranty database, gm submitted 1,561 claims of crank position sensor failure that it also stated were indeterminate as to whether an engine stall occurred while driving.In total, gm reports 4,701 claims of crank position sensor failure combining regular warranty and extended warranty.Similar to gms statistical analysis, odis analysis showed that the failure rate for warranty claims of engine stall while driving at three years in service is low (less than 1%).However, further analysis determined that the my 2001 vehicle build period from may 2000 through october 2000 had significantly higher (more than four times) crank position failure rates in both consumer complaint data and warranty claim data than in the build period from november 2000 through july 2001.Adding the claims of known engine stall while driving and claims where engine stall was indeterminate, the failure rate at three years in service for this population is over 6%.An engineering analysis (ea06-016) has been opened to further assess the frequency and potential safety consequences associated with the alleged defect in vehicles built from may 2000 through october 2000.
  

  Show Content

• Parking brake failure investigation # DP05009

  Odis review of complaint data received since the close of ea04-011 revealed no indication that the investigation should be re-opened.More details can be found in the federal register notice enclosed in the dp05-009 public file.Odi reserves the right to reopen the investigation in the future should conditions warrant.
  

  Show Content

• Unwanted low-speed abs activation investigation # PE05020

  There is no summary currently available
  

  Show Content

• Parking brake failure investigation # EA04011

  In a letter dated april 20, 2005, gm notified nhtsa that it had decided that defects that relate to motor vehicle safety exist in certain model year (my) 1999-2002 c/k 1500 series (pbr parking brake system) and my 2001-2005 c/k 2500 and 3500 series (trw parking brake system) pickups with manual transmissions.According to gm, some of these vehicles may have conditions that cause the friction linings to wear to an extent where the parking brake can become ineffective in immobilizing a parked vehicle.Gms action covers an estimated total of 142,585 vehicles.Dealers will install a low-force spring clip retainer for vehicles equipped with the pbr parking brake system and install a redesigned parking brake cable assembly on vehicles equipped with the trw parking brake system. A total of 58 non-duplicative complaints were received by odi and gm concerning the approximately 59,000 my 1999-2002 c/k 1500 series pickup trucks with the pbr parking brake system.These included 22 alleged rollaway incidents, resulting in a rate of 38.5 rollaway incidents per 100,000 vehicles.Odi is aware of 24 complaints regarding the my 2001-2005 c/k 2500 and 3500 series manual transmission trucks recalled by gm, including 5 alleging rollaway incidents.Though the conditions described in gms letter are also present in the c/k trucks with automatic transmissions, the rollaway rate in those vehicles was similar to those observed in peer vehicles studied by odi in this investigation.This engineering analysis is closed. For additional information, see the attached closing report.
  

  Show Content

• Tailgate cable breakage investigation # EA04005

  General motors filed a defect notice 04v-129 on march 17, 2004, which outlines a program to replace the tailgate cables installed in affected model year 2000-2004 vehicles.Refer to odis closing report for ea04-005 for additional information.Odi is aware of reports of tailgate cable breakage occurring in model year 1999 and earlier vehicles.These vehicles were equipped with similar tailgate cables as addressed by 04v-129, but are not being addressed by campaign o4v-129.Odi is initiating a separate investigation to address these vehicles.The complaint-injury-fatality statistics summarized above pertain to model year 2000-2004 vehicles. The complaint-injury statistics for model year 1999 and earlier vehicles are summarized on the opening resume for that investigation.
  

  Show Content

• Parking brake failure investigation # PE03057

  Odi opened pe03-057 to assess parking brake ineffectiveness in the subject vehicles.These vehicles are equipped with four wheel disc brakes that incorporate a single-shoe drum-in-hat parking brake independent of the service brakes.Complaint and warranty data indicate that the parking brake linings tend to wear out early in the life of the vehicle (at an average of 24 months in service), reducing the parking brake systems torque below that needed to immobilize the vehicle.Gm has attributed this accelerated wear to foreign material intrusion and a failure of the brake shoe to properly self-center within its brake drum.Effective with the start of my 2003 production, a newer reduced force hold-down clip was introduced to facilitate brake shoe disengagement from the drum surface.This part is also available at the service level for the my 1999-2002 vehicles.Gm has indicated that the paking brake is intended to operate in conjunction with the transmission to immobilze parked vehicles, and that in many cases, accelerated parking brake lining wear is caused by rough use, vehicle modifications, and driving with the parking engaged. Odi has upgraded the preliminary evaluation to an engineering analysis to gather further information concerning parking brake usage factors and the circumstances surrounding the seventeen reported vehicle crashes.
  

  Show Content

• Throttle sticking closed investigation # EA02015

  This investigation involves the general motors corporation (gm)throttle body (tb) utilized in model year (my) 1999-2002 silverado, sierra, tahoe, suburban, avalanche and yukon (subject vehicle(s)) with 4.8l, 5.3l, and 6.0l engines. The tb valve may intermittently stick in a closed position.In such a situation, an operator may apply additional accelerator pedal force to increase engine speed.The application of additional accelerator pedal force, to open a stuck throttle valve, may open the throttle valve more than intended and, in turn, accelerate the engine and vehicle more than intended and reasonably expected by the driver.On august 1, 2002, the office of defects investigation (odi), of the national highway traffic safety administration (nhtsa), opened this engineering analysis.The investigation revealed that two factors may cause the defect: 1) tb manufacturing process problems; and 2) accumulation of deposits (a pcv system by-product) on or around the tb throttle valve and bore.Odi concludes that the tb performs in a defective manner after analyzing gm?S data submissions, and test data collected by the vehicle research and test center (vrtc).Fifty-nine crashes are alleged to have occurred as a result of gm?S tb defect.The majority of the crashes involve a single vehicle, engaging in a close quarter vehicle maneuver (or low speed), and causing only minor property damage.Four out of the fifty-nine crashes involve injury, and those injuries were minor.Although gm?S tb is defective, based on the evidence gathered, odi has found that the accelerator pedal force required to open a stuck throttle valve is negligible, and the throttle valve does not stick in the open position.Therefore this engineering analysis (ea02-015) will be closed at this time.The closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist.For a detailed discussion of the tb component and testing, please see the attached report.
  

  Show Content

I was driving about 45 miles an hour coming down an overpass. The brake pedal went completely to the floor and i narrowly avoided a crash. I took to my mechanic. They said that the brake lines were completely rusted out. I am not getting this fixed as it is an older truck but i do think that someone could die from this defect.

I was driving about 45 miles an hour coming down an overpass. The brake pedal went completely to the floor and i narrowly avoided a crash. I took to my mechanic. They said that the brake lines were completely rusted out. I am not getting this fixed as it is an older truck but i do think that someone could die from this defect.

Vehicle was parked in garage. Metal support bar in the back upper portion of driver seat broke. Seat was being used as ordinary and snapped when i went to retrieve item from back seat by reach over center console and to back seat to grab purse. I weight 135 pounds and am small person. No extraordinary pressure or weight shift. I have found numerous complaints online from people seeking solutions on how to repair this extremely common issue as to lead me to believe these seats are defective and dangerous .Refuse to drive truck as not certain that safety belt will be of any use in an accident as seat flops around now and has awkward tilt back to one side on the console side and lays back to far to clearly see over dash even when fully posturing erect.

Vehicle was parked in garage. Metal support bar in the back upper portion of driver seat broke. Seat was being used as ordinary and snapped when i went to retrieve item from back seat by reach over center console and to back seat to grab purse. I weight 135 pounds and am small person. No extraordinary pressure or weight shift. I have found numerous complaints online from people seeking solutions on how to repair this extremely common issue as to lead me to believe these seats are defective and dangerous .Refuse to drive truck as not certain that safety belt will be of any use in an accident as seat flops around now and has awkward tilt back to one side on the console side and lays back to far to clearly see over dash even when fully posturing erect.

161131 miles frame rusted real bad body looks great for the year i just bought the truck looked real clean inside and out from origanal owner put it on a lift and the frame is so rusted out did some googleing and found that most all these trucks were built to rot out in 3 years

Tl* the contact owns a 2002 gmc sierra 1500. While reversing the vehicle, the brake pedal became stuck to the floorboard. The contact was able to engage the emergency brake to stop the vehicle. The contact inspected the vehicle and found that all the brake lines were corroded, which caused the brake fluid to leak. The vehicle was towed to bowser automotive (132-168 north lewis run road, west mifflin, pa 15236, (412) 469-2100) where it was diagnosed that all the brake lines were severely corroded and needed to be replaced. The vehicle was not repaired. The manufacturer was not contacted. The failure mileage was 75,000.

Tl* the contact owns a 2002 gmc sierra 1500. While driving approximately 45 mph, the vehicle's braking ability was lost and the brake pedal traveled to the floorboard. The vehicle eventually came to a stop and was towed to the contact's residence. The vehicle was not taken to the dealer or an independent mechanic for diagnostic testing. The manufacturer was notified of the failure. The vehicle was not repaired. The approximate failure mileage was 158,000.

Spare tire fell off from the cable, unknown, i also had a 2001 gmc yukon and the same thing happened, this is unsafe as it could become detached while moving and needs to be recalled

Tl* the contact owns a 2002 gmc sierra 1500. While driving between 3-8 mph, the brake pedal was depressed and the anti-lock brake system engaged, increasing the braking distance. There were no warning indicators illuminated. The contact mentioned that the failure occurred intermittently. The vehicle was taken to an independent mechanic where it was diagnosed that there was rust between an abs sensor and the hub in the front driver and passenger side wheels. The hub and sensor needed replacement, but the vehicle was not repaired. The gmc dealer (jeff wyler florence buick gmc, 1154 burlington pike, florence, ky 41042 (859) 279-4590) informed the contact that the vin was not included in any service bulletins or recalls. The manufacturer was contacted and confirmed that the vin was not included in nhtsa campaign number: 05v379000 (service brakes, hydraulic). The failure mileage was approximately 165,000.

Common OBD-II Error Codes

• P050D [2] Cold Start Rough Idle
• P0300 [13] Random/Multiple Cylinder Misfire Detected
• P0308 [2] Cylinder 8 Misfire Detected
• P0442 [2] Evaporative Emission Control System Leak Detected (small leak)
• P0455 [1] Evaporative Emission Control System Leak Detected (gross leak)
• P2723 [1] Pressure Control Solenoid "E" Performance/Stuck Off
• P0877 [1] Transmission Fluid Pressure Sensor/Switch "D" Circuit Low
• U1500 [1] U1500
• P0446 [2] Evaporative Emission Control System Vent Control Circuit Malfunction
• P0451 [1] Evaporative Emission Control System Pressure Sensor Range/Performance
• P0454 [1] Evaporative Emission Control System Pressure Sensor Intermittent
• P0757 [3] Shift Solenoid B Stuck On
• P0742 [2] Torque Converter Clutch Circuit Stock On
• U1041 [2] SCP (J1850) Invalid or Missing Data for Vehicle Speed
• C0201 [2] Reverse speed sensor right front - signal out of range / performance
• C0265 [2] C0265
• P1172 [2] Invalid Test
• P2636 [2] Fuel Pump "B" Low Flow/Performance
• P0093 [5] Fuel System Leak Detected - Large Leak
• P1093 [5] Fuel system - malfunction
• P0128 [2] Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)
• C0306 [1] Magnet / sensor TCS # 2 right front - signal out of range / performance
• C0308 [1] Magnet / sensor TCS # 2 right front - high input signal
• U2104 [1] Engine control module (ECM), CAN data bus - malfunction detected
• P0335 [2] Crankshaft Position Sensor A Circuit Malfunction
• P0336 [2] Crankshaft Position Sensor A Circuit Range/Performance
• P0171 [1] System too Lean (Bank 1)
• P0174 [1] System too Lean (Bank 2)
• P0706 [1] Transmission Range Sensor A Circuit Range/Performance
• P0721 [3] Output Speed Sensor Range/Performance
• P0500 [1] Vehicle Speed Sensor "A" Malfunction
• C0055 [1] Steering Wheel Position Sensor "Signal D" (Subfault)
• C0237 [2] Magnet / Meter # 1 ABS Left Front - Signal out of range / performance
• C0374 [1] C0374
• U1026 [1] SCP (J1850) Invalid or Missing Data for Engine RPM
• B2618 [1] B2618
• P0087 [3] Fuel Rail/System Pressure - Too Low
• P0847 [4] Transmission Fluid Pressure Sensor/Switch "B" Circuit Low
• P0872 [6] Transmission Fluid Pressure Sensor/Switch "C" Circuit Low
• P0875 [4] Transmission Fluid Pressure Sensor/Switch "D" Circuit
• P0708 [3] Transmission Range Sensor A Circuit High Input
• P1711 [6] Not in P or N During KOEO / KOER
• P1713 [4] Transfer Case Neutral Indicator Hard Fault Present
• U1000 [1] CAN bus network code
• P0802 [1] Transmission Control System MIL Request Circuit/Open
• P1781 [1] Ignition Retard Request Duration Fault
• P0420 [1] Catalyst System Efficiency Below Threshold (Bank 1)
• P0430 [1] Catalyst System Efficiency Below Threshold (Bank 2)
• P0621 [2] Generator Lamp "L" Control Circuit Malfunction
• P0380 [2] Glow Plug/Heater Circuit "A"
• C0543 [1] C0543
• P1285 [1] Injection Control Pressure Out Of Range Low
• P1286 [1] Injection Control Pressure Out Of Range High
• P2133 [1] Throttle/Pedal Position Sensor/Switch "F" Circuit High
• P0841 [1] Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance
• P0843 [1] Transmission Fluid Pressure Sensor/Switch "A" Circuit High
• P0870 [1] Transmission Fluid Pressure Sensor/Switch "C" Circuit
• P0701 [1] Transmission Control System Range/Performance
• P1709 [1] Digital TRS Failed to Transition States in KOEO / KOER
• P0700 [2] Transmission Control System Malfunction
• P0339 [1] Crankshaft Position Sensor A Circuit Intermittent
• P1223 [1] CID High
• P0101 [1] Mass or Volume Air Flow "A" Circuit Range/Performance Problem
• C0455 [1] C0455
• P0236 [1] Turbocharger Boost Sensor A Circuit Range/Performance
• P0102 [1] Mass or Volume Air Flow "A" Circuit Low Input
• P0103 [1] Mass or Volume Air Flow "A" Circuit High Input
• P0731 [1] Gear I Incorrect ratio
• P0732 [1] Gear 2 Incorrect ratio
• P0733 [1] Gear 3 Incorrect ratio
• P0734 [1] Gear 4 Incorrect ratio
• P0743 [1] Torque Converter Clutch Circuit Electrical
• P0746 [1] Pressure Control Solenoid A Performance or Stuck Off
• P0747 [1] Pressure Control Solenoid A Stuck On
• P0776 [1] Pressure Control Solenoid B Performance or Stuck Off
• P0777 [1] Pressure Control Solenoid B Stuck On
• P1720 [1] SSA Inductive Signature Malfunction
• P1721 [1] SSB Inductive Signature Malfunction
• P1723 [1] SSD Inductive Signature Malfunction
• P1724 [1] TFT Sensor In Range Failure High
• P0193 [1] Fuel Rail Pressure Sensor A Circuit High Input
• P0201 [4] Injector Circuit Malfunction - Cylinder 1
• P0208 [4] Injector Circuit Malfunction - Cylinder 8
• P0730 [1] Incorrect Gear Ratio
• P0756 [1] Shift Solenoid B Performance or Stock Off
• P0116 [1] Engine Coolant Temperature Sensor Circuit 1 Range/Performance Problem
• P0181 [2] Fuel Temperature Sensor A Circuit Range/Performance
• B2725 [1] B2725
• P0332 [1] Knock Sensor 2 Circuit Low Input (Bank 2)
• C1500 [1] Transfer Case Contact Plate "B" Encoder Circuit Failure