Volvo Vnl 2007

• Recall 97116 [USA]: Without a signal to disengage the clutch when the brakes are applied, the distance required to stop the truck may lengthen, increasing the risk of a crash.
  Volvo trucks north america (volvo) is recalling certain model year 2007-2014 vah, vhd, vnl, vnm, and vt models. The affected vehicles were built without a redundant clutch disengagement switch. Without a redundant switch, a loss of signal from the brake air pressure switch can prevent the clutch from automatically disengaging when the brake is applied.
  volvo trucks will notify owners and dealers will inspect and repair the vehicles if necessary. The recall began on august 26, 2013. Volvo's recall number is rvxx1303. Owners may contact volvo at 1-336-393-2000.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

• Recall 67654 [USA]: If this happens a short circuit may occur, which over time could possibly lead to a vehicle fire.
  Volvo trucks is recalling 127,764 my 2001-2008 vhd, vnl, vnm, and my 2005-2008 vt trucks. A seal may fail allowing water and contaminants to seep into the windshield wiper motor.
  volvo will replace the wiper motor free of charge. Since this recall involves a large number of vehicles, volvo will release the recall in stages as parts are received. Priority will be given to the vehicles located in the regions/states that have a corrosive environment. The recall began on september 30, 2009. Owners may contact volvo trucks at 1-800-528-6586.
  volvo trucks recall no. Rvxx0902.Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

• Recall 84107 [USA]: If left untreated, the crack can propagate and cause failure of the brake cam tube support bracket(s), which can result in loss of brakes at the corresponding wheel end increasing the risk of a crash.
  Volvo trucks is recalling 366 my 2006-2009 vnl trucks equipped with super single tires, bendix brake cam tubes, and volvo air suspension. The vibration frequency from the suspension with super single tires may result in a fatigue crack of the mounting brackets for the brake cam tube.
  dealers will add a support bracket to the brake cam tube. The recall began on june 30, 2009. Owners may contact volvo trucks at 1-800-528-6586.
  volvo recall no. Rvxx0901.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov .

• Recall 74791 [USA]: If a short circuit occurs and is left untreated, components and wiring may be subject to overheating which could possibly result in a vehicle fire.
  On certain heavy duty trucks, the circuit protection (i.E. Automatic circuit breakers) used to protect the vehicle lighting system may not provide adequate protection.
  dealers will replace the circuit breakers with fuses. The recall began on february 25, 2008. Owners may contact volvo trucks at 1-800-528-6586.
  volvo trucks recall no. Rvxx0707.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

• Recall 71848 [USA]: There is a possibility that the pivot bolt can become loose without the driver's knowledge. when this occurs, the driver could drive away and the trailer could become disengaged, increasing the risk of a crash.
  On certain trucks equipped with a saf holland simplex fifth wheel, the lever arm pivot bolt may have been over tightened. An over tightened pivot bolt can distort the pivot bolt spacer sleeve, which may prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin.
  dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer free of charge. The recall began on january 28, 2008. Owners may contact volvo trucks at 1-800-528-6586.
  volvo trucks recall no. Rvxx0705.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

• Recall 88918 [USA]: If the condition exists and the key is left on without fuel in the filter, the heating element may heat to a point where a flame becomes present at the tip of the element which could result in a vehicle fire.
  On certain trucks, an unprotected lead in the thermoswitch of the heater may make contact with another post possibly creating a short circuit, which can result in continuous operation of the heating element.
  dealers will inspect the thermoswitch and will replace it if necessary. The recall began on september 10, 2007. Owners may contact volvo trucks at 1-800-528-6586.
  volvo truck recall no. Rvxx0703.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

• Recall 32199 [USA]: If the nut were to come loose, the steering shaft could potentially separate resulting in loss of steering control which could cause a crash.
  On certain trucks, the nut used to retain the steering shaft may or may not be a lock nut that has the locking feature. A lock nut is required to provide additional resistance to ensure that the nut does not come loose.
  dealers will replace the steering shaft pinch bolts and locknuts free of charge. The recall began on august 24, 2007. Owners may contact volvo trucks at 1-800-528-6586.
  volvo recall no. Rvxx0702.Customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

• Recall 33083 [USA]: If a fatigue failure occurs and is left unattended, the axle may lock up or the end of the axle could come off, which may result in a vehicle crash.
  On certain trucks, the axle housings may have been manufactured with steel that was out of specification which could result in a fatigue failure over time.
  dealers will repair and inspect the axles and replace them free of charge. The recall began on april 9, 2007. Owners may contact volvo trucks at 1-800-528-6586.
  volvo trucks recall no. Rvxx0701.Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.Safercar.Gov.

• Recall 37007 [USA]: This could result in additional damage to the driveline, the vehicle to which it is attached and ay additional nearby objects.
  On certain trucks equipped with arvinmeritor rpl20 high angle interaxle driveshafts, an improper seated or missing snap ring can result in the bearing cup to separate from the slip yoke sub-assembly. The universal joint cross could then contact the slip yoke casting and eventually cause the ear work to fracture.
  dealers will inspect the driveshafts and replace them as needed. The recall began on october 23, 2006. Owners may contact volvo trucks at 1-800-528-6586.
  volvo truck recall no. Rvxx0605.Customers can also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.Safercar.Gov.

• Recall 2013221 [Canada]: Other
  On certain vehicles, the secondary clutch disengagement switch may have been omitted during vehicle assembly or, in some instances, removed during servicing. As such, primary switch failure would cause the automated manual transmission’s clutch to remain engaged when the brakes are applied. This could increase stopping distances, possibly resulting in a crash causing property damage and/or personal injury. Correction: dealers will install a micro-switch at the brake pedal and update the software to run a diagnostic on the switch during engine start-up.

• Recall 2009025 [Canada]: Brakes
  On certain trucks equipped with super single tires, vibration frequency from the suspension may result in fatigue cracking of the mounting brackets for the brake cam tubes. In time the crack could propagate and cause of the brake cam tube support bracket(s) to fail, which could result in a loss of brakes at the corresponding wheel end. This could increase stopping distances, possibly causing a vehicle crash resulting in property damage, personal injuries or death. Correction: dealers will install an additional support bracket to the brake cam tubes.

• Recall 2009144 [Canada]: Other
  On certain vehicles, the windshield wiper motor may be susceptible to water intrusion, which could result in an electrical short circuit and a fire. This could cause property damage, personal injury or death. Correction: dealers will affect repairs.

• Recall 2007084 [Canada]: Other
  On certain trucks, the axle housing may have been manufactured with steel that was out of specification (9.5mm thick instead of 11mm thick), which could result in a fatigue failure over time. If failure occurs, the axle may lock-up or the end of the axle could come off, which may result in a vehicle crash with injury or death. Correction: dealers will inspect and, if required, replace the axles.

• Recall 2007253 [Canada]: Steering
  On certain trucks, the locknut used to retain the steering shaft may not have had the lock feature. As a result, the nut could loosen, allowing the steering shaft to separate, causing a loss of steering control which could result in a vehicle crash with injury or death. Correction: dealers will replace the steering shaft pinch bolt and locknut.

• Recall 2007257 [Canada]: Fuel supply
  On certain trucks, when the ignition key is in the 'on' position, the pre-heater, located in the fuel filter base, is energized. If this pre-heater is energized while maintenance is being performed on the fuel filter, diesel fuel could ignite within the filter housing. A fire within the fuel filter housing may spread possibly resulting in property damage or personal injury. Correction: dealers will inspect and, if required, replace the fuel heater assembly.

• Recall 2007338 [Canada]: Other
  On certain trucks, the fifth wheel hitch assembly's lever arm may have been incorrectly installed during the manufacturing process. The lever arm pivot bolt may have been over-tightened which could distort the pivot bolt spacer sleeve and prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin. This could allow the towed unit to separate from the towing vehicle while underway, potentially causing a crash with injury or death. Correction: dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer.

• Recall 2007394 [Canada]: Electrical
  On certain trucks, the automatic circuit breakers used to protect the vehicle lighting system may not provide adequate protection. If a short circuit occurs, components and wiring may be subject to overheating, which could result in a vehicle fire, causing property damage and/or personal injury or death. Correction: dealers will replace the circuit breakers with fuses.

• Recall 2006243 [Canada]: Powertrain
  On certain trucks, an improperly seated or missing u-joint snap ring can result in the bearing cup to separate from the slip yoke sub-assembly. The u-joint could then contact the slip yoke casting and eventually cause the ear to fracture. This could result in additional damage to the driveline, the vehicle and any nearby objects. Correction: dealers will inspect and, if required, replace the driveshafts.

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Stop lamp switch signal investigation as of 20130207

  The office of defects investigation (odi) received early warning reporting (ewr) data from the manufacturer that indicated some number of subject vehicles equipped with the subject automated manual transmission had allegedly experienced a condition where the clutch failed to automatically disengage the transmission from the engine as intended. This may result in extended stopping distances and/or unintended forward motion of a vehicle previously at rest.To date, odi is aware of 134 subject vehicles with one or more complaints or field reports related to this condition.Also, odi is aware of 164 subject vehicles with one or more warranty claims related to this condition.By letter dated june 25, 2013, volvo trucks north america (volvo) notified odi that it has initiated a safety recall (nhtsa recall no. 13v268 and volvo recall no. Rvxx1303) to address a safety defect in approximately 23,003 model year (my) 2007 through 2014 volvo vah, vhd, vnl, vnm and vt model trucks. The affected vehicles were manufactured from december 20, 2006 through may 22, 2013 and were originally equipped with the subject automated manual transmissions.According to volvo, reports of the subject transmission clutch mechanism failing to automatically disengage as intended are associated with the removal of a brake pedal micro switch that provided a redundant signal to the transmission control module indicating the brakes had been applied.Previously, volvo had removed this brake pedal micro switch from new vehicle production and from certain vehicles already in-service via two field service campaigns (sp 432-024 and sp 432-026) because it decided the switch was unnecessary and/or a maintenance issue.In the absence of this redundant brake pedal micro switch, the clutch mechanism may fail to disengage the transmission from the engine at low vehicle speed should the stop lamp switch fail to send and/or the transmission control module fail to receive the primary signal.At the time of this closing, volvo is evaluating available remedies and will provide nhtsa with details when the recall remedy procedure has been finalized.Volvo will notify affected owners by mail by august 25, 2013.Please see nhtsa recall no. 13v268 for details.Accordingly, this investigation is closed.
  

  Show Content

• Volvo sleeper glass de-bonding investigation as of 20110523

  Odi opened recall query rq11-001 after a review of ewr field reports identified lower bunk window separations on the subject vehicles.Volvo had issued three recalls for sleeper window separations since 2003.Additionally, volvo had issued two bulletins for sleeper window issues during the same time period.The frequency of related actions led odi to open this formal investigation.An information request (ir) letter was sent to volvo on 23 june 2011.Volvo responded on 17 august 2011 and then provided updated warranty information on 9 january 2012.Volvo provided production change data and warranty information which was correlated to vehicle build month and failure date.Odi analyzed the data to determine if additional production time frames should have been included in previous recalls.Odi also requested information from its network of fleet owners.The response from this network reaffirmed the accuracy of the updated warranty information.Based on the information and data received, odi has concluded that all production periods have been appropriately addressed by volvos previous recalls and no additional recall action is required at this time.
  

  Show Content

• Saf holland fifth wheel assembly investigation as of 20070914

  On october 18, 2007 volvo trucks north america filed defect report 07v-496 which outlines a safety recall program to notify the affected owners and correct the affected vehicles.
  

  Show Content

Common OBD Error codes specific to this vehicle.

• U0121 [1] Lost Communication With Anti-Lock Brake System (ABS) Control Module
• P0420 [1] Catalyst System Efficiency Below Threshold (Bank 1)
• P111C [1] P111C
• P040A [1] Exhaust Gas Recirculation Temperature Sensor "A" Circuit
• P040B [1] Exhaust Gas Recirculation Temperature Sensor "A" Circuit Range/Performance
• P1121 [1] Engine Coolant sensor out of range/ECT Sensor Out Of Self Test Range
• P009E [2] Fuel Pressure Relief Control Performance/Stuck Off
• P208E [2] Reductant Injection Valve Stuck Closed Bank 1 Unit 1
• P103B [2] P103B
• P2459 [2] Diesel Particulate Filter Regeneration Frequency
• P0194 [1] Fuel Rail Pressure Sensor A Circuit Intermittent
• P249F [1] Excessive time to enter closed loop Diesel particulate filter (DPF) regeneration control
• P24A0 [1] Closed loop Diesel particulate filter (DPF) regeneration control, control limit reached – temperature too low
• P0128 [1] Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)
• P226C [1] ISO/SAE Reserved
• P2002 [1] Diesel Particulate Filter Efficiency Below Threshold Bank 1
• P24A4 [1] P24A4
• P10FE [1] P10FE
• P249C [1] Excessive time to enter closed loop reductant injection control
• P0422 [1] Main Catalyst Efficiency Below Threshold (Bank 1)

I'd like to request from this department to open an investigation on a rusty frame problem on 2005, 2006, 2007 and 2008 commercial volvo vnl trucks. These trucks have high tendency to have frame rust and even perforation putting motorists at risk in the usa highways.

The hood bracket cuts through the hood on the passenger side of the truck. This causes the hood to only be secured with one bracket when opening the hood for daily inspections. The hood is only partially secured when operating on roads and highways. *tr

The hood bracket cuts through the hood on the passenger side of the truck. This causes the hood to only be secured with one bracket when opening the hood for daily inspections. The hood is only partially secured when operating on roads and highways. *tr

I have ~15 years experience driving most make/models of class 8 trucks in alaska and lower 48 states. I have never operated any truck with low beam headlights so bad that i had to risk blinding on-coming traffic with my high beams in order to operate at all after sunset - until this one. The projector style lens sheds little more light on the pavement ahead than i expect from a clearance lamp shop mechanics tell me that this is normal for all volvo trucks using the "vn" style aero-composite design. On the other hand, the high beam, fog and driving lamps are wonderful. This really is stunningly dangerous and needs an investigation. I'm mystified that nhtsa hasn't acted already. Could it be as simple as worn out bulbs? ...Incorrect bulbs? Invisibly degraded projector lenses? ...Degraded voltage to the bulbs? Whatever is wrong, nobody seems to know how to fix it. And every night i operate, i worry that i might be blamed for an incident because my low beams keep me blind or because i blinded on-coming traffic with my high beams. How 'bout it nhtsa? This is your opportunity to fix something before people get hurt. Please see also: http://www.Thetruckersreport.Com/truckingindustryforum/volvo-forum/168835-started-volvo-headlight-complaint-with-nhtsa.Html. *tr

Tl* the contact owns a 2007 volvo vnl truck. The contact was driving 20 mph when he lost control of steering and crashed into a pole. The vehicle was towed to a local mechanic who performed a diagnostic that located the failure at the drag link. The drag link separated from the fire wall. The drag link and the tie rod was replaced. A police report was filed (oklahoma state police report number: am02905-11). The failure and the current mileage was 507,648.

Tl*the contact owns a 2007 volvo 780vnl semi heavy duty truck. The engines electrical system shut on and off when the vehicle was in traffic. The contact was able to restart the vehicle; however, none of the electrical components would function. The vehicle was taken to the dealer twice. The mass air flow sensor and the wires that shorten the frame of the truck which the abs sending unit communicates with each brake system were replaced. The manufacturer was called and advised the contact to call them back in a couple of days. The failure mileage was 354,926.

Tl* the contact owns a 2007 volvo vnl64t truck. The contact stated the headlight covers were deteriorating and reducing visibility for the driver. In addition, the failure would cause the headlights to become extremely foggy and hazy. There were no recalls for the vehicle and the dealer advised any repairs would be at the contacts expense. The vehicle was not repaired. The failure mileage was 122,000 and the current mileage was 174,928.

Tl-the contact owns a 2007 volvo vnl64t truck. While inspecting the vehicle he notice the headlights covers was deteriorating and the plastic was flogged. The covers deteriorating reduces visibility for the drivers. The vehicle has not been repaired. He has contact the dealer and was told there were no recall. The cost per the dealer would be over $600. The failure mileage was 120,000 and the current mileage was 186,221. Vwb

2007 volvo vnl right front tire blew out causing damage to the right side fuel tank. *kb ohio traffic crash report # 10-0764-90. *jb

The sleeper window on our 2007 volvo vnl truck fell out onto a brand new police car in olahoma city, oklahoma, just west of the city. Driver states that the window is attached by glue only, no screws or rivits. Upon furhter investigation by our fleet, drivers have been instructed not to open sleeper winows. This was to avoid any further porblems such as this incident

2007 volvo vnl semi-truck was leaking diesel fuel due to a hole in the fuel tank. *nj (ohio traffic crash report # 10-0413-90) *jb updated02/24/10 *bf

Bunk windown has fallen out on several occations. Driver says "he did set up a case" with volvo and they would not do anything about it. Not covered under any warranty driver says he fixed problem with a general motors valve cover washer and a sheet metal screw but is not able to open this window any longer.

2007 volvo 780, bought in 7-31-2006, when driving from texas to california we had problems with transmission going into gear. From that time on the problems have gotten worse and to the point of being unsafe. It breaks down frequently and won't go into gear. We have been towed numerous times and have lost revenue. It has melted wires and components. The computer throws out codes that indicates problems with the computer, electrical, transmission, vehicle, brakes, etc., etc. The truck has been down numerous times. Most recent, down in october of 07, down in dec. Of 07, down in april 07 two times. Is now broken down in slc, ut and is at the volvo dealership there. I bought a new truck so that it would be reliable like volvo claimed it to be. It now just shuts down and you are dead in your tracks. It has melted two voltage doublers. It is unsafe to be on the road. I want a new truck, one that runs. I paid for the new truck, i pay my monthly payments even when the truck is broken down. Volvo has a ten point service commitment that they don't keep. I need help! I'm going to loose my contract with fed ex and go out of business because this truck is a lemon! Please inform me if you know what i can do, who i can talk to, where i can go for assistance to get to the bottom of this on going problem that has not yet been resolved. Thank you! *tr

Tl*the contact owns a 2007 volvo vnl. The contact stated that the brake chambers caught fire while the vehicle was in motion. The fire department extinguished the fire and there were no injuries. A police report was filed. The manufacturer was notified and is investigating the issue. The contact has not received any reimbursement. The dealer has not returned his calls or emails. The speed was unknown. The failure mileage was 100,000. Updated 03-27-09 *bf updated 03/31/09.*jb the consumer stated the brake chambers leaked air slightly. Updated 04/01/09. *jb

Tl*the contact owns a 2007 volvo vnl. While driving 55 mph, the steering wheel locked and then eased up. While turning the steering wheel to make a left turn, the steering wheel made a clanking sound and the load shifted and relocked. The contact had to forcefully turn the wheel to the right to gain control of the vehicle. The vehicle dragged for 150 feet and the guard rail saved his life. He also stated that the power steering worked intermittently throughout the failure. The dealer and manufacturer stated that they would not provide any information on the defect or the vehicle. They also threatened to release the information to his contract job, which could result in his termination. The vehicle was destroyed. The contact sustained bruises to his legs and arms. The guard rails sustained property damage. A police report was filed. The purchase date was unknown. The current and failure mileages were 24.

Hendrickson air ride front suspension foa class 8 trucks: suspension has been inspected by truck dealer and said to be operating normally. However at speeds over 50 mph chassis leaning and rocking makes directional control difficult. Steering input was vague and turn-in when navigating corners induces directional control problems as well as aggravating stability problems. *ak