Prevost X3-45 Commuter 2018

Vehicle Details: Recalls, Investigations, Service Bulletins

Below you will find all available information on the 2018 PREVOST X3-45 Commuter.

ManufacturerKnown WMI(s)Fuel Type
PREVOST
PREVOST VIN Decoder

Use the box here to look up VINs from PREVOST as well as other manufacturers

#
Frequently Asked Questions
  • Are there recalls for the 2018 PREVOST X3-45 Commuter?
     - There are 8 recall(s) for the 2018 PREVOST X3-45 Commuter, additional information is below.
NHTSA Mandated Recalls
  • Recall 260240 [USA]: Beacons that do not provide proper illumination may be less visible to wheelchair lift users, increasing the risk of injury.

  • Recall 248160 [USA]: An inoperative engine stop button can increase the risk of injury to a service technician.

  • Recall 203554 [USA]: A damaged seat belt assembly may not buckle properly, increasing the risk of injury during a crash.

  • Recall 192299 [USA]: An overheated alternator bearing can increase the risk of a fire.

  • Recall 147411 [USA]: If the engine unexpectedly shuts down, passengers may have to be transferred to another vehicle on the side of the road, increasing the risk of an injury. if the engine unexpectedly shuts down while the vehicle is in motion, there is an increased risk of crash.

  • Recall 140684 [USA]: If the fire suppression system does not work as intended, it can increase the risk of injury in the event of a fire.

  • Recall 133716 [USA]: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.

  • Recall 138389 [USA]: If the fuel tank separates from the vehicle, it could be a road hazard and the vehicle would stall. either scenario increases the risk of a crash.

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • IS-23019 - SUSPENSION: Sway bar collars improvement
  • IS-18106 - STEERING: Kit power steering tank convertion cummins to zf with d13 engine
  • IS-20051 - EQUIPMENT: Driver's barrier installation instructions
  • IS-21072B - ELECTRICAL SYSTEM: Steering gateway. Revision b - pin 2 and 10 were inverted on connector a139
  • MI22-12B - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: b - general update
  • SP18-35J - ENGINE AND ENGINE COOLING: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency. Revision j - range of applicable vins updated.
  • MI22-12A - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: a - erroneous secondary & accessory tanks location.
  • MI22-12 - SERVICE BRAKES, AIR: Air tanks draining sequence
  • IS-17151C - EXTERIOR LIGHTING: Halogen to led fog light replacement kit. Revision: c - advanced kits canceled
  • SP18-35J - ENGINE AND ENGINE COOLING: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency. Revision j - range of applicable vins updated.
  • IS-22902 - WHEELS: Tag axle hub flange - alternate cap screw
  • IS21-072 - ELECTRICAL SYSTEM: Steering gateway, revision a : cancel watch dog removal from efd part of the instruction
  • MI20-08C - EQUIPMENT: Storage and startup guidelines : part number updates
  • IS21-901 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : X3 series envirocare - ions air sanitizer
  • IS21-072A - ELECTRICAL SYSTEM: Steering gateway revision a cancel watch dog removal from efd part of the instruction
  • IS20-925A - VISIBILITY: Central hvac merv filters installation
  • IS22-040 - EQUIPMENT ADAPTIVE/MOBILITY: Brake pedal seal plate installation kit
  • IS21-072 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Steering gateway schematic
  • SP18-35H - EQUIPMENT: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • SP18-35H - EQUIPMENT ADAPTIVE/MOBILITY: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • IS19-108 - FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY:PRESSURE RELIEF DEVICES: Surge tank pressure cap replacement
  • SP18-39D - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Scr converter replacement - aftertreatment system
  • SP18-35H - EQUIPMENT:MECHANICAL: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • MI18-16B - ELECTRICAL SYSTEM: Bosch hd10 alternator diagnostic guide revision b to avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
  • SP18-35H - POWER TRAIN: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • MI21-13A - EQUIPMENT: An automated test is available to check the big hvac superheat from the driver seat. This test is controlled by multiplex, eliminating interventions and the need to take measures on the vehicle.
  • SR19-31C - EQUIPMENT: Engine control module (ecm) software update - engine cooling strategy in high altitude operation revision c: vin range in application box rearranged for h3 coaches
  • MI21-06 - FUEL SYSTEM, DIESEL: Diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair ⿿ from us10 to newer engine generation
  • SP18-35F - POWER TRAIN: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency rev e: expiration date removed
  • Mi21-07A - WHEELS: Ront & tag axle ⿿ unitized hub bearing end play verification and replacement
  • IS-21901 - EQUIPMENT: X3 series envirocare - ions air sanitizer
  • IS-18042 - ELECTRICAL SYSTEM: Eberspacher preheater installation in replacement of spheros & valeo preheaters
  • MI20-08C - STRUCTURE: Storage and startup guidelines: periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, prevost recommends foll
  • IS-20925A - POWER TRAIN: Central hvac merv filters installation reva
  • VBC-PREVOST 4 - EQUIPMENT ADAPTIVE/MOBILITY:VEHICLE CONTROLS:BRAKING: Communication letter from accociate administration for enforcement, nhtsa from prevost subject vehicle brand: prevost (ewr#000650)
  • IS-18091A - STEERING: Tie rod 610052 first installation instructions: use these instructions when replacing the drop joint tie rod on s82, s84 / s84u i-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment ne
  • MI20-19B - ENGINE AND ENGINE COOLING: Introducing a new engine coolant into prevost service center network
  • MI20-19A - ENGINE AND ENGINE COOLING: Rev a: mention added concerning ddc series 60 engine sca requirement
  • MI21-01 - EQUIPMENT: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI21-01 - POWER TRAIN: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • SP18-39C - FUEL SYSTEM, DIESEL: Scr converter replacement - aftertreatment system revision: c expiration date removed 12/22/2020
  • SP18-35E - FUEL SYSTEM, DIESEL: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency rev e: expiration date removed
  • MI20-19 - EQUIPMENT: Introducing a new engine coolant into service
  • MI18-02A - ENGINE AND ENGINE COOLING: Engine oil & filter change intervals - volvo d13 engine, from us10 revision: a updated for obd20 engines
  • IS-13169A - BACK OVER PREVENTION: SENSING SYSTEM: RADAR: Prevost aware adaptive cruise braking (acb) flr20 radar sensor replacement kit revision a: kit is13169-1 & is13169-2 canceled, use 145373 &145372
  • MI20-14 - VISIBILITY: Prevost driver assistâ¿¢ - windshield replacement equipped with camera
  • IS-20929 - EQUIPMENT: Uv lights installation in ac compartment
  • IS-20929 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Uv lights installation in a/c compartment
  • P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • U17_P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • MI20-08B - EQUIPMENT: Storage and startup guidelines revision: b parts added to suggested material 08-10-2020
  • IS-20922 - EQUIPMENT ADAPTIVE/MOBILITY: Sigma passenger seats partition kit
  • MI18-18B - EQUIPMENT: General hoisting and towing procedures revision: b updated 2.1 to show rubber chocks, secure front and rear.
  • MI20-12 - STEERING: Jerky, noisy or hard to turn steering gearbox. Hydraulic end limiter adjustment. All models ⿿ equipped with rb bosch/zf servocom or servocomtronic steering gearbox
  • IS-20907 - EQUIPMENT ADAPTIVE/MOBILITY: Plexiglass panel behind driver x3
  • MI20-08A - EQUIPMENT: Storage and startup guidelines: rev a: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
  • IS-19906G - ELECTRICAL SYSTEM: Bosch to delco remy alternator installation, x3-45 with electric fan drive revision g: updated mux parameter value name.
  • MI20-09 - EQUIPMENT: Prevost vehicle disinfection procedure revision a
  • IS-19084 - EQUIPMENT: Accessory air filter replacement replaces 642192
  • U17_P040200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • U02A200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes U02A200 lost communication with reductant quality module
  • U029E00 - ENGINE (PWS): Repair instructions to address fault codes U029E00 lost communication with nox sensor "b"
  • U029D00 - ENGINE (PWS): Repair instructions to address fault codes U029D00 lost communication with nox sensor "a"
  • P256000 - EQUIPMENT: Repair instructions to address fault codes P256000 engine coolant level low
  • P242A15 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P242A15 exhaust gas temperature sensor bank 1 sensor 3 - circuit short to battery or open
  • P20E892 - EQUIPMENT: Repair instructions to address fault codes P20E892 reductant pressure too low - performance orincorrect operation
  • P208464 - EQUIPMENT: Repair instructions to address fault codes P208464 exhaust gas temperature sensor circuit range/performance bank 1 sensor 2 - signal plausibility failure
  • P204A13 - EQUIPMENT: Repair instructions to address fault codes P204A13 reductant pressure sensor - circuit open
  • P204713 - EQUIPMENT: Repair instructions to address fault codes P204713 reductant injection valve control bank 1 unit 1 ⿿ circuit open
  • P203F00 - EQUIPMENT: Repair instructions to address fault codes P203F00 reductant level low
  • P203115 - EQUIPMENT: Repair instructions to address fault codes P203115 exhaust gas temperature sensor bank 1 sensor 2 - circuit short to battery or open
  • P10CE97 - EQUIPMENT: Repair instructions to address fault codes P10CE97 reductant return: no flow detected - componentor system operation obstructed or blocked
  • P107575 - EQUIPMENT: Repair instructions to address fault codes P107575 clutch system - emergency position not reachable
  • P107017 - BRAKES (PWS): Repair instructions to address fault codes P107017 gearbox brake valve (vagb) - circuit voltage above threshold
  • P105998 - POWER TRAIN: Repair instructions to address fault codes P105998 gearbox oil temperature sensor - component orsystem over temperature
  • P054415 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P054415 exhaust gas temperature sensor bank 1 sensor 1 - circuit short to battery or open
  • P052400 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P052400 engine oil pressure too low
  • P040200 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • P029800 - ENGINE (PWS): Repair instructions to address fault codes P029800
  • P021700 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P021700 engine coolant over temperature condition
  • NOx_Conv2 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P207F-00; P20EE-00
  • NOX_Conv1 - EQUIPMENT ADAPTIVE/MOBILITY: Repair instructions to address fault codes P207F-00 - reductant quality
  • FUELFILTER - ENGINE (PWS): Repair instructions to address fault codes P008A-00; P0087-00
  • MI20-09 - EQUIPMENT:OTHER:LABELS: Prevost vehicle disinfection procedure
  • MI20-08 - UNKNOWN OR OTHER: Storage and startup guidelines - all prevost vehicles & volvo 9700
  • IS-20905 - EQUIPMENT: Hand sanitizer dispenser installation
  • MI15-24 - EQUIPMENT ADAPTIVE/MOBILITY: Added: power cables for l.H. Side alternator & fan drive breaker box
  • IS-19921A - EQUIPMENT: This instruction sheet explains how to install a seatbelt cutter in the driver's area
  • IS-19066 - SERVICE BRAKES, AIR: This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
  • SCI19-01C - ELECTRICAL SYSTEM: The intent of this procedure is to guide you through the steps required to program a mcm especially for the control of the electric fan drive as required for conversion kit of instruction sheets is-19900, is-19901, is19910, is-19912.
  • IS-17151 - LIGHTING (PWS): This instruction sheet explains how to replace halogen fog light to led's
  • IS-19040A - STEERING: This instruction sheet explains how to replace power steering pump discharge hose (pressure) - #161335p or #160039
  • SP19-26B - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, an update to the engine ems software must be carried out by qualified technicians. Contact your service manager to schedule an appointment and have the update performed
  • SP18-35D_English - FUEL SYSTEM, DIESEL: On vehicles with active code P20EE, perform the following checklist and operations.
  • IS-18091 - STEERING: This instruction sheet explains how to perform the first installation of tie rod 610052 on prevost vehicles equipped with dana s82, s84 / s84u i-beam axles, 1994- today
  • sp19-26A - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, an update to the engine ems software must be carried out by qualified technicians. Contact your service manager to schedule an appointment and have the update performed
  • SCI19-20 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the vehicle program has to be upgraded. This allows the intelligent sleep mode (ism) system improvement to prevent batteries drain when ism is enabled. This procedure shows how to generate the vehi
  • Wb19-11 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the vehicle program might need to be upgraded to prevent batteries drain when ism (intelligent sleep mode) is enabled.
  • SP19-26 - FUEL SYSTEM, DIESEL: On the vehicles affected by this bulletin, an update to the engine ems software must be carried out by qualified technicians.
  • MI18-45A - POWER TRAIN: Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to is-18091 for installation instruction
  • Mi14-34D - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: Prevost aware adaptive cruise braking (acb) - flr20 & flr21 radar sensor alignment
  • IS-19915 - EQUIPMENT: Mp-1000 multimedia player installation
  • IS-19040 - STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS: Power steering pump discharge hose (pressure) replacement
  • IS-18910 - EQUIPMENT: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-18158 - EQUIPMENT: Toilet drain valve replacement
  • WB19-07 - SERVICE BRAKES, AIR: On the independent front suspension (ifs) of the vehicles affected by this bulletin, check and make sure that there is enough clearance between the brake hoses identified in the procedure and their respective support bracket.
  • SP18-35C_English - ENGINE AND ENGINE COOLING: On vehicles with active code P20EE, perform the following checklist and operations.
  • IS-19906D - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles equipped with electric fan drive
  • IS-19040 - STEERING: This instruction sheet explains how to perform the replacement of the power steering pump discharge hose (pressure) #161335p or #160039, using kit #160127;
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet shows how to install a flap over the diesel filling cap.
  • WB19-02A - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin replace the idler and belt tensioner support on the left side (hot side) of the engine by an improved part, 011213. This applies to installations with bosch or delco remy alternators on the hot side
  • IS-19906C - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles
  • SP18-35B_English - ENGINE (PWS): On vehicles with active code P20EE, perform the following checklist and operations.
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet explains how to install a flap over the diesel filling cap
  • IS-17071A - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • SP18-39B - ENGINE (PWS): This special bulletin explains how to perform the replacement of the scr tank, when authorized.
  • MI19-06 - BRAKES (PWS): This maintenance information is published to answer some questions regarding the inverted or ?Trailing? Mounting position of the drive axle brake calipers on prevost vehicles
  • MI19-05 - EQUIPMENT: This maintenance information expains how to adjust p/n 660865, 660699 draglinks
  • IS-17102A - EQUIPMENT: This instruction sheet explains how to install ism (intelligent sleep mode) on x series with prime hardware
  • IS-19906 - ELECTRICAL SYSTEM: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles equipped with efd
  • Sp18-39A - ENGINE AND ENGINE COOLING: This special bulletin explains how to perform the replacement of the scr tank, when authorized.
  • SCI18-46 - EQUIPMENT:ELECTRICAL: This service center instructions explains how to install the prevost ultimate entertainment system
  • SP18-39 - EQUIPMENT: This special bulletin explains how to perform the replacement of the scr tank, when authorized.
  • Sp18-35 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : On vehicles with active code P20EE, perform the following checklist and operations.
  • SP18-308A - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, add 300ml of oil in the bitzer a/c compressor as per production retrofit r18053.
  • SP18-306 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available.
  • MI18-28 - STRUCTURE:BODY:DOOR : On the vehicles affected by this bulletin, the compressor door may be adjusted for proper fit following the procedure below.
  • WB18-04 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available.
  • MI18-27B - ELECTRICAL SYSTEM: This maintenance information presents the amerex fire suppression system, and its recommended maintenance
  • IS-18904 - BACK OVER PREVENTION: SENSING SYSTEM: CAMERA : This procedure shows how to install a rear camera.
  • MI18-37 - POWER TRAIN:AUTOMATIC TRANSMISSION: This maintenance information presents information about the removal or installation of the lang kk73.1 electromagnetic clutch - part of the bitzer (model 4nfcy) air conditioning compressor.
  • MI18-27A - ELECTRICAL SYSTEM: This maintenance information presents the amerex fire suppression system, and its recommended maintenance
  • MI18-21A - ENGINE AND ENGINE COOLING: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-18A - EQUIPMENT: This maintenance information explains how to tow and hoist prevost vehicles.
  • WB18-01A - STRUCTURE: On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
  • WB18-07B - EQUIPMENT: On the vehicles affected by this bulletin, the busbar connected to circuit breaker cb13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper inst
  • Sp18-20 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, replace the ac compressor discharge hose.
  • MI18-27 - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information presents the amerex fire suppression system, and its recommended maintenance
  • MI18-18 - EQUIPMENT:MECHANICAL:WRECKER AND WHEEL LIFT DEVICES: This maintenance information explains how to tow and hoist prevost vehicles.
  • IS-18901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the engine belt guard on x3 series vehicles with coolant system electrical fan drive.
  • MI18-22 - EQUIPMENT:ELECTRICAL: This maintenance information presents information about the eld installation and parameter list on prevost coaches
  • MI18-21 - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-16A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information presents guidelines to help with the diagnosis of the bosch hd10 alternators
  • IS-18902 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to installa parcel rack door kits
  • WB18-09 - ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES: On the vehicles affected by this bulletin, one of the battery ground cables may have been incorrectly crimped and must be replaced following the procedure below.
  • WB18-08 - ENGINE (PWS): On the vehicles affected by this bulletin use the following procedure to install the engine belt guard.
  • WB18-07 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the busbar connected to circuit breaker cb13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper inst
  • IS-17905 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-13009B - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install and adjust drag link # 660699
  • WB18-07A - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the busbar connected to circuit breaker cb13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper inst
  • WB18-06 - EQUIPMENT: On the vehicles affected by this bulletin, replace the existing right console ramp p/n 392494 with the new right console ramp p/n 3200962.
  • MI18-02 - ENGINE AND ENGINE COOLING: This mainteannce informaiton presents the latest engine oil & filter change intervals for the volvo engine
  • IS-18901 - ENGINE AND ENGINE COOLING: This instruction sheet explains how to install an engine belt guard
  • IS-17907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the volvo electronic logging device (eld)
  • IS-17071 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • WB18-03 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, due to a software issue, replace the battery equalizer in the main power compartment.
  • Wb18-01 - LATCHES/LOCKS/LINKAGES:DOORS:LATCH: On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
  • MI17-22 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: This maintenance information explains how to inspect the fuel tank cradle mounting screws on a yearly basis
  • CK17-30 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is now possible to replace the older generation tgw 2.0 (3g network) by the newer 2.1 version (4g the network) using accessory kit 23266301 and the following procedure.
  • CK17-26 - ENGINE (PWS): On the vehicles affected by this bulletin, it is now possible to disable the engine brake automatic function by running accessory kit # 23181730.
  • SP17-18 - ELECTRICAL SYSTEM:WIRING: On the vehicles affected by this bulletin, remove relay r26, isolate and/or reconnect wires according to the wiring diagram d061670 p18.2 revision 8. Also move water pump ground connection to the electronic ground pin a54 j2.14 and rename c
Known Recall Investigations
  • Alternator front bearing failure investigation # PE21011

    Nhtsas office of defects investigation (odi) is opening a preliminary evaluation after receiving a tip from a fleet safety manager concerning alternator front bearing failures that cause elevated temperatures within the engine compartment, resulting in the fire suppression system (fss) activating, immediately shutting the engine down, and rendering the bus inoperable. Review of early warning reporting data identified 9 field reports for model year (my)2015 through my2019 h3 and x3 prevost buses, describing alternator failures in any of 3 alternators equipped on the bus. In some cases, a minor fire occurred damaging nearby electrical harnesses. An immediate shut down of the bus can increase the risk of a crash or injury of passengers when transferring to another bus.Odi is opening this investigation to evaluate the cause, consequence, scope and frequency of the alleged defect in the subject prevost buses.

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.