16NA383

Service Bulletin
Bulletin No.:
16-NA-383
Date:
May, 2019
INFORMATION
Subject:
Information on Rough Idle, Crank No Start, Extended Crank or Misfire Due to Excessive
Carbon on Top of the Valves or Sticking Valves, Malfunction Indicator Light (MIL)
Illuminated - DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308 Set
This Bulletin replaces PIP5029H. Please discard PIP5029H.
Brand:
Model:
Buick
GM
Passenger
Cars and
Trucks
(including
LCF MD)
Cadillac
Chevrolet
GMC
Model Year:
VIN:
from
to
2000
2019
from
to
Engine:
Transmission:
Gasoline
Engines Only
Involved Region or Country
North America and N.A. Export Regions
Condition
Some customers may comment on the following conditions:
• Rough idle
• Crank no start
• Extended crank
• Engine misfire
The technician may find one or more of the following DTCs set:
• P0300
• P0301
• P0302
• P0303
• P0304
• P0305
• P0306
• P0307
• P0308
SI diagnosis may or may not isolate the cause of the misfire depending on whether the
intake/exhaust valves are sticking at the time of the diagnosis.
Cause
This condition may be caused by major carbon build up on the intake and/or exhaust
valves due to fuel contamination or incomplete burning of the fuel as shown below, so the
misfires should not have appeared until accumulating at least 8,000 km (5,000 mi)
or more.
Copyright 2019 General Motors LLC. All Rights Reserved.
Page 2
May, 2019
Note: Fuel oxidation and volatility concerns can often
cause these issues as well, however they cannot
generally be checked in service. Trying a different, high
quality Top Tier fuel and regular oil changes is
sometimes the best diagnostic. Additional gasoline
retailers are added to the TOP TIER list when their
gasoline meet the TOP TIER Detergent Gasoline
Standards. For the most up to date list of fuel marketers
that offer TOP TIER Detergent Gasoline, refer to this
website: www.toptiergas.com.
Bulletin No.: 16-NA-383
Information
Important: A new reformulated Top Engine Cleaner
has been released by CCA Parts and is recommended
and approved to use in the GM vehicle line.
The graphics below may show typical carbon build-up
during engine disassembly and inspection of the
cylinder heads:
2836273
2857954
2836275
2857955
Bulletin No.: 16-NA-383
May, 2019
2857957
When the engine is cold, the compression on multiple
cylinders may be at 0 kPa (0 psi).
The engine also may pop through the intake or exhaust
while cranking and the spark plugs may be fuel fouled
when inspected.
Some engines may also experience valve damage or
cam followers that are out of position as a result of this.
If this concern is encountered, perform SI diagnosis. If
the SI diagnosis leads to a compression loss due to a
valve sealing concern and/or eliminates everything else
external to the engine, the following information
may help:
• If there is no sign of valve damage or cam
followers that are out of place, perform the
following procedure to free up sticking valves and
to remove carbon from the valves and pistons.
• If valve damage is present or if there are cam
followers that are out of place, perform engine
mechanical repairs as necessary to correct the
concern and then perform the procedure below to
prevent the concern from returning.
Page 3
2857956
Page 4
•
•
May, 2019
Bulletin No.: 16-NA-383
Perform an upper engine and valve cleaning
procedure.
Below are examples of valves that have gone
through a Top Engine cleaning procedure.
Before Cleanup
After Cleanup
3979074
3979169
4791643
4791651
Bulletin No.: 16-NA-383
May, 2019
Before Cleanup
Page 5
After Cleanup
4791647
4791652
4791649
4791655
Video Training (U.S. Dealers)
There is also a related training video on this subject
that was included in the January 2013 Emerging Issues
Video that technicians should consider viewing.
Because the training video does not mention this,
please note that it is acceptable to use equivalent tools
and the engine oil and filter should also be replaced to
complete the repairs. The training video is available at
the GM Center of Learning Website and can be viewed
by following this path:
⇒ Go to www.centerlearning.com
⇒ Enter Training ID
⇒ Click Resources
⇒ Click Service Know How / Tech Assist
⇒ Click Emerging Issues
⇒ Click 10213.01D - January 2013 Emerging
Issues (VOD)
⇒ Click the Topics Tab on Upper Right
⇒ Click Link for PIP5029: Decarbonizing Valves in
SIDI Engines
Page 6
May, 2019
Bulletin No.: 16-NA-383
Service Procedure
Warning: Please follow all safety instructions
noted on the bottle and service tool. Ensure safety
glasses and gloves are being worn during the
procedure.
Fuel Injector Cleaner Kit J-35800-A
Cleaner Nozzle EN-35800-20
4630850
Important: Extreme care must be taken not to
hydro-lock the engine when inducing the cleaner,
especially if it is induced without Fuel Injector
Cleaner Kit J-35800-A or equivalent. If too much
cleaner is induced at too low of an RPM, or if you
force the engine to stall by inducing too much
cleaner at once, the engine may hydro-lock and
bend a connecting rod(s).
1. Fill Cleaner Kit J-35800-A with Top Engine
Cleaner, approximately 473 ml (16 oz), and close
the cap of the tool tightly. Set the air pressure to
260 kPa (40 psi) at the service tool.
2. Using GDS 2 or Scan Tool, command engine idle
to 2000 rpm to prevent the engine from stalling.
Typically 2,000 rpm will be sufficient.
Note: Two applications of the Top Engine Cleaner may
be necessary to perform a total cleanup depending on
the condition of the combustion chamber.
3. In a well-ventilated area with the engine at
operating temperature, slowly/carefully induce the
Top Engine Cleaner into the engine, which should
take approximately 3 minutes.
⇒ For best results, it is suggested to induce the
cleaner through the throttle body with Fuel
Injector Cleaner Kit J-35800-A or equivalent
and NEW Cleaner Nozzle EN-35800-20, which
has been developed to help atomize the
cleaner.
4630851
4. After the entire contents of Top Engine Cleaner has
been induced, continue to run the engine for
2 minutes at idle.
5. Change the engine oil and filter, and advise the
customer to only use one of the Top Tier Gasoline
locations listed at http://www.toptiergas.com and/or
in the latest version of Service Bulletin
05-06-04-022 to minimize future deposits. It can
also be recommended to add a bottle of GM Fuel
System Treatment Plus at every oil change as
mentioned in the latest version of Service Bulletin
04-06-04-051.
6. Test drive the vehicle, using only light
acceleration, and clear any DTCs if necessary.
Bulletin No.: 16-NA-383
May, 2019
Page 7
Important: GM does not recommend the use of any
aftermarket top engine cleaning product. Some
products may cause harmful effects to components
or seals and may void the terms of the vehicle
warranty. Use only the GM products listed below,
which have been tested and approved.
Parts Information
Description
Part Number
Qty
ACDelco Top Engine Cleaner
19355198 (In Canada, use
P/N 19355199)
1
Fuel System Treatment Plus - Gasoline
88865595 (In Canada, use
P/N 88865598)
1
Fuel System Treatment Plus – Flex Fuel
88865596 (In Canada, use
P/N 88865599)
1
Oil Filter, Engine
Refer to EPC
1
Oil, Engine
Refer to EPC
5 qt
Warranty Information
For vehicles repaired under the Emission coverage,
use the following labor operation. Reference the
Applicable Warranties section of Investigate Vehicle
History (IVH) for coverage information.
Labor
Operation
Description
Labor Time
4080148*
Decarbon Engine Using
Upper Engine Cleaner
0.5 hr
Add
Change Engine Oil and
Filter
0.3 hr
*This is a unique Labor Operation for Bulletin use only.
Version
2
Modified
May 21, 2019 – Added the 2019 Model Year, updated the Video Training section to
remove Canada and updated step 6 of the Service Procedure.
GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these
technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper
service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a
job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your
vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the
information.
WE SUPPORT VOLUNTARY
TECHNICIAN
CERTIFICATION