Prevost X3-45 Vip Entertainer 2014

Vehicle Details: Recalls, Investigations, Service Bulletins

Below you will find all available information on the 2014 PREVOST X3-45 Vip Entertainer.

ManufacturerKnown WMI(s)Fuel Type
PREVOST
PREVOST VIN Decoder

Use the box here to look up VINs from PREVOST as well as other manufacturers

#
Frequently Asked Questions
  • Are there recalls for the 2014 PREVOST X3-45 Vip Entertainer?
     - There are 12 recall(s) for the 2014 PREVOST X3-45 Vip Entertainer, additional information is below.
NHTSA Mandated Recalls
  • Recall 260229 [USA]: Beacons that do not provide proper illumination may be less visible to wheelchair lift users, increasing the risk of injury.

  • Recall 191633 [USA]: An overheated alternator bearing can increase the risk of a fire.

  • Recall 138427 [USA]: A complete loss of steering would increase the risk of a crash.

  • Recall 133714 [USA]: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.

  • Recall 138393 [USA]: If the fuel tank separates from the vehicle, it could be a road hazard and the vehicle would stall. either scenario increases the risk of a crash.

  • Recall 122302 [USA]: If the fasteners loosen, the trailer hitch may deform or detach from the vehicle, increasing the risk of a crash.

  • Recall 114513 [USA]: The damaged wires may activate the afss and shutdown the engine, increasing the risk of a vehicle crash.

  • Recall 112414 [USA]: In the event of a fire, if the fire extinguisher does not work correctly, there is an increased risk of injury to the bus occupants.

  • Recall 115768 [USA]: If the seat belt retractor does not lock, the seat occupant may not be properly restrained during a vehicle crash, increasing their risk of personal injury.

  • Recall 100616 [USA]: Without functioning windshield wipers, the driver's visibility may be reduced, increasing the risk of a crash.

  • Recall 97560 [USA]: Drivers may mistake exceedingly bright tail lamps to be brake lamps confusing following drivers about the intention to brake, increasing the risk of a crash.

  • Recall 2017570 [Canada]: Accessories

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • IS-23019 - SUSPENSION: Sway bar collars improvement
  • IS-18106 - STEERING: Kit power steering tank convertion cummins to zf with d13 engine
  • MI16-32 - ENGINE AND ENGINE COOLING: Improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • IS-19912E - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with delco remy alternator. Revision: e note added regarding power cable connection
  • IS-19901E - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with bosch alternator. Revision: e note added regarding power cable connection
  • IS-21072B - ELECTRICAL SYSTEM: Steering gateway. Revision b - pin 2 and 10 were inverted on connector a139
  • MI22-12B - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: b - general update
  • MI22-12A - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: a - erroneous secondary & accessory tanks location.
  • MI22-12 - SERVICE BRAKES, AIR: Air tanks draining sequence
  • IS-17151C - EXTERIOR LIGHTING: Halogen to led fog light replacement kit. Revision: c - advanced kits canceled
  • IS-22902 - WHEELS: Tag axle hub flange - alternate cap screw
  • IS21-072 - ELECTRICAL SYSTEM: Steering gateway, revision a : cancel watch dog removal from efd part of the instruction
  • MI20-08C - EQUIPMENT: Storage and startup guidelines : part number updates
  • IS21-901 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : X3 series envirocare - ions air sanitizer
  • IS21-072A - ELECTRICAL SYSTEM: Steering gateway revision a cancel watch dog removal from efd part of the instruction
  • IS20-925A - VISIBILITY: Central hvac merv filters installation
  • MI18-16B - ELECTRICAL SYSTEM: Bosch hd10 alternator diagnostic guide revision b to avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
  • MI21-06 - FUEL SYSTEM, DIESEL: Diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair ⿿ from us10 to newer engine generation
  • Mi21-07A - WHEELS: Ront & tag axle ⿿ unitized hub bearing end play verification and replacement
  • IS-21901 - EQUIPMENT: X3 series envirocare - ions air sanitizer
  • IS-19912D - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator - x3 series us10 up to ghg17 cooling system
  • IS-19901D - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator
  • IS-18042 - ELECTRICAL SYSTEM: Eberspacher preheater installation in replacement of spheros & valeo preheaters
  • IS-19901C - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator - x3 series us10 up to ghg17 cooling system
  • IS-19912C - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator
  • MI20-08C - STRUCTURE: Storage and startup guidelines: periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, prevost recommends foll
  • IS-20925A - POWER TRAIN: Central hvac merv filters installation reva
  • VBC-PREVOST 2 - EQUIPMENT ADAPTIVE/MOBILITY: Bendix m-32qr abs modulator valve replaced by new m-40qr valve.
  • VBC-PREVOST 1 - EQUIPMENT:MECHANICAL:BOOM/CRANE/LADDER:HOSES/CABLES/RODS/GEARS/STRUT/CYLINDER: Communication letter from accociate administration for enforcement, nhtsa from prevost subject vehicle brand: prevost (ewr#000650)
  • SP21-300 - EQUIPMENT: Automatic fire suppression system - tamper seal replacement
  • IS-18091A - STEERING: Tie rod 610052 first installation instructions: use these instructions when replacing the drop joint tie rod on s82, s84 / s84u i-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment ne
  • MI20-19B - ENGINE AND ENGINE COOLING: Introducing a new engine coolant into prevost service center network
  • MI20-19A - ENGINE AND ENGINE COOLING: Rev a: mention added concerning ddc series 60 engine sca requirement
  • MI21-01 - EQUIPMENT: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI21-01 - POWER TRAIN: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI20-19 - EQUIPMENT: Introducing a new engine coolant into service
  • SP17-301 - EQUIPMENT: On the vehicles affected by this bulletin, replace the ahi dozer by an improved part preventing nozzle clogging.
  • SP16-322C - WHEELS: On the vehicles affected by this bulletin, replace the front axle wheel hub bearing unit with an improved version.
  • IS-14145 - ELECTRICAL SYSTEM: This instruction sheet explains how to add sunshade switches on the dashboard
  • MI16-17D - SEATS: Use this procedure for the removal and installation of the twin bosch hd10 (120a or 150a) alternators.
  • MI18-02A - ENGINE AND ENGINE COOLING: Engine oil & filter change intervals - volvo d13 engine, from us10 revision: a updated for obd20 engines
  • IS-20007A - VISIBILITY: Driver⿿s air condenser replacement and relocation revision: a material: added hardware.
  • IS-13169A - BACK OVER PREVENTION: SENSING SYSTEM: RADAR: Prevost aware adaptive cruise braking (acb) flr20 radar sensor replacement kit revision a: kit is13169-1 & is13169-2 canceled, use 145373 &145372
  • P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • U17_P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • MI20-08B - EQUIPMENT: Storage and startup guidelines revision: b parts added to suggested material 08-10-2020
  • IS-20007 - EQUIPMENT: Driver's air condenser replacement and relocation x3-45vip from e-5459 to h-6179 retrofitted with efd
  • IS-20922 - EQUIPMENT ADAPTIVE/MOBILITY: Sigma passenger seats partition kit
  • MI18-18B - EQUIPMENT: General hoisting and towing procedures revision: b updated 2.1 to show rubber chocks, secure front and rear.
  • MI20-12 - STEERING: Jerky, noisy or hard to turn steering gearbox. Hydraulic end limiter adjustment. All models ⿿ equipped with rb bosch/zf servocom or servocomtronic steering gearbox
  • IS-19901B - EQUIPMENT: Electric fan drive cooling system conversion with bosch alternator revision b: parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal, st,16
  • IS-19912B - ENGINE (PWS): Electric fan drive cooling system conversion with delco remy alternator revision : b parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal,
  • IS-20907 - EQUIPMENT ADAPTIVE/MOBILITY: Plexiglass panel behind driver x3
  • MI20-08A - EQUIPMENT: Storage and startup guidelines: rev a: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
  • MI20-09 - EQUIPMENT: Prevost vehicle disinfection procedure revision a
  • IS-19084 - EQUIPMENT: Accessory air filter replacement replaces 642192
  • U17_P040200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • U02A200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes U02A200 lost communication with reductant quality module
  • U029E00 - ENGINE (PWS): Repair instructions to address fault codes U029E00 lost communication with nox sensor "b"
  • U029D00 - ENGINE (PWS): Repair instructions to address fault codes U029D00 lost communication with nox sensor "a"
  • P256000 - EQUIPMENT: Repair instructions to address fault codes P256000 engine coolant level low
  • P242A15 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P242A15 exhaust gas temperature sensor bank 1 sensor 3 - circuit short to battery or open
  • P20E892 - EQUIPMENT: Repair instructions to address fault codes P20E892 reductant pressure too low - performance orincorrect operation
  • P208464 - EQUIPMENT: Repair instructions to address fault codes P208464 exhaust gas temperature sensor circuit range/performance bank 1 sensor 2 - signal plausibility failure
  • P204A13 - EQUIPMENT: Repair instructions to address fault codes P204A13 reductant pressure sensor - circuit open
  • P204713 - EQUIPMENT: Repair instructions to address fault codes P204713 reductant injection valve control bank 1 unit 1 ⿿ circuit open
  • P203F00 - EQUIPMENT: Repair instructions to address fault codes P203F00 reductant level low
  • P203115 - EQUIPMENT: Repair instructions to address fault codes P203115 exhaust gas temperature sensor bank 1 sensor 2 - circuit short to battery or open
  • P10CE97 - EQUIPMENT: Repair instructions to address fault codes P10CE97 reductant return: no flow detected - componentor system operation obstructed or blocked
  • P107575 - EQUIPMENT: Repair instructions to address fault codes P107575 clutch system - emergency position not reachable
  • P107017 - BRAKES (PWS): Repair instructions to address fault codes P107017 gearbox brake valve (vagb) - circuit voltage above threshold
  • P105998 - POWER TRAIN: Repair instructions to address fault codes P105998 gearbox oil temperature sensor - component orsystem over temperature
  • P054415 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P054415 exhaust gas temperature sensor bank 1 sensor 1 - circuit short to battery or open
  • P052400 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P052400 engine oil pressure too low
  • P040200 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • P029800 - ENGINE (PWS): Repair instructions to address fault codes P029800
  • P021700 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P021700 engine coolant over temperature condition
  • NOx_Conv2 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P207F-00; P20EE-00
  • NOX_Conv1 - EQUIPMENT ADAPTIVE/MOBILITY: Repair instructions to address fault codes P207F-00 - reductant quality
  • FUELFILTER - ENGINE (PWS): Repair instructions to address fault codes P008A-00; P0087-00
  • MI20-09 - EQUIPMENT:OTHER:LABELS: Prevost vehicle disinfection procedure
  • MI20-08 - UNKNOWN OR OTHER: Storage and startup guidelines - all prevost vehicles & volvo 9700
  • IS-20905 - EQUIPMENT: Hand sanitizer dispenser installation
  • IS-19912A - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator - mention added stating to disable ⿿prime⿝; parts added in the kit.
  • IS-19901A - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator - x3 series us10 up to ghg17 cooling system - mention added stating to disable ⿿prime⿝; parts added in the kit
  • MI15-24 - EQUIPMENT ADAPTIVE/MOBILITY: Added: power cables for l.H. Side alternator & fan drive breaker box
  • IS-19901A - ENGINE AND ENGINE COOLING: Revision : mention added stating to disable prime & parts added in the kit.
  • IS-19921A - EQUIPMENT: This instruction sheet explains how to install a seatbelt cutter in the driver's area
  • IS-19066 - SERVICE BRAKES, AIR: This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
  • SCI19-01C - ELECTRICAL SYSTEM: The intent of this procedure is to guide you through the steps required to program a mcm especially for the control of the electric fan drive as required for conversion kit of instruction sheets is-19900, is-19901, is19910, is-19912.
  • IS-19912 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system conversion kit (with delco remy alternators) on x3 vehicles equipped with us10 up to ghg17 engine.
  • IS-19901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system with bosch alternators on x3 series vehicles equipped with us10 up to ghg17 engines
  • IS-17151 - LIGHTING (PWS): This instruction sheet explains how to replace halogen fog light to led's
  • IS-19040A - STEERING: This instruction sheet explains how to replace power steering pump discharge hose (pressure) - #161335p or #160039
  • SP19-301 - EQUIPMENT: On the vehicles affected by this bulletin, the compressor & radiator door lower hinges must be replaced by new stainless steel units
  • sp19-304 - LATCHES/LOCKS/LINKAGES: On the vehicles affected by this bulletin, the t-key cylinder lock must be disassembled and lubricated, the latch pin inspected for damage and replaced as required. The upper and lower door stops must also be inspected if found broken or mi
  • IS-19912 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system conversion kit (with delco remy alternators) on x3 vehicles equipped with us10 up to ghg17 engine.
  • IS-19901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system with bosch alternators on x3 series vehicles equipped with us10 up to ghg17 engines;
  • IS-18091 - STEERING: This instruction sheet explains how to perform the first installation of tie rod 610052 on prevost vehicles equipped with dana s82, s84 / s84u i-beam axles, 1994- today
  • WB19-14 - ELECTRICAL SYSTEM: Neutral gear - software update
  • MI18-45A - POWER TRAIN: Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to is-18091 for installation instruction
  • Mi14-34D - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: Prevost aware adaptive cruise braking (acb) - flr20 & flr21 radar sensor alignment
  • IS-19922 - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: Prevost aware adaptive cruise braking (acb) flr10 to flr21 radar sensor upgrade
  • IS-19915 - EQUIPMENT: Mp-1000 multimedia player installation
  • IS-19040 - STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS: Power steering pump discharge hose (pressure) replacement
  • IS-18910 - EQUIPMENT: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-18025A - SUSPENSION: This instruction sheet shows how to replace kneeling level sensor #21643575 by sensor #22194741.
  • IS-18025A - SUSPENSION: This instruction sheet shows how to replace kneeling level sensor #21643575 by sensor #22194741.
  • WB19-07 - SERVICE BRAKES, AIR: On the independent front suspension (ifs) of the vehicles affected by this bulletin, check and make sure that there is enough clearance between the brake hoses identified in the procedure and their respective support bracket.
  • IS-19909D - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles
  • IS-19040 - STEERING: This instruction sheet explains how to perform the replacement of the power steering pump discharge hose (pressure) #161335p or #160039, using kit #160127;
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-19909A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet explains how to install a flap over the diesel filling cap
  • IS-17071A - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • MI19-06 - BRAKES (PWS): This maintenance information is published to answer some questions regarding the inverted or ?Trailing? Mounting position of the drive axle brake calipers on prevost vehicles
  • MI19-05 - EQUIPMENT: This maintenance information expains how to adjust p/n 660865, 660699 draglinks
  • SP18-13F - STEERING:LINKAGES:DRAG:LINK:CONNECTION: On the vehicles affected by this bulletin, proceed to the replacement of the drag link.
  • IS-19909 - ELECTRICAL SYSTEM: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles
  • IS-13009D - STEERING:LINKAGES:DRAG:LINK:CONNECTION: This instruction sheet explains how to install and adjust drag link # 660699
  • SCI18-46 - EQUIPMENT:ELECTRICAL: This service center instructions explains how to install the prevost ultimate entertainment system
  • IS-13009C - STEERING:LINKAGES:DRAG:LINK:CONNECTION: This instruction sheet explains how to install and adjust drag link # 660699
  • IS-18907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install hatches with fan on x3 vehicles.
  • WB18-43 - POWER TRAIN: This warranty bulletin explains how to update the vecu (vehicle electronic control unit) parameters to allow auto engine brake function with the i-shift transmission.
  • Sp18-302 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, install a pressure switch into the front service compartment to send a faster signal to the allison transmission to switch to neutral at stop.
  • WB18-04 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available.
  • SP18-305A - LATCHES/LOCKS/LINKAGES: On the vehicles affected by this bulletin, apply thread locker on the double door latch pins internal threads
  • MI18-37 - POWER TRAIN:AUTOMATIC TRANSMISSION: This maintenance information presents information about the removal or installation of the lang kk73.1 electromagnetic clutch - part of the bitzer (model 4nfcy) air conditioning compressor.
  • MI18-21A - ENGINE AND ENGINE COOLING: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-18A - EQUIPMENT: This maintenance information explains how to tow and hoist prevost vehicles.
  • MI18-05 - ENGINE AND ENGINE COOLING: This maintenance information explains how to install valve assembly 130009 in replacement of valve 641274
  • MI16-17G - ENGINE AND ENGINE COOLING: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • IS-15003E - ELECTRICAL SYSTEM: This insruction sheet explains how to insall the bosch hd10 24v-150a alternator conversion kit ? Twin bosch mounted on volvo d13 engine
  • Sp18-304A - EQUIPMENT:MECHANICAL: For vehicles affected by this bulletin, on the wheelchair area sliding door, install a new upper roller carrier, adjust the door and inspect all fasteners.
  • Sp18-303 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, the condenser compartment wall may present fatigue cracks on or near the a/c receiver tank support. Follow these instructions to repair and improve the support.
  • Sp18-301 - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK ASSEMBLY: On the vehicles affected by this bulletin, the existing surge tank support has to be replaced by a new configuration including two supports. That will allow a better distribution of the load between the tank and the support.
  • MI18-18 - EQUIPMENT:MECHANICAL:WRECKER AND WHEEL LIFT DEVICES: This maintenance information explains how to tow and hoist prevost vehicles.
  • SP17-314-R13 - INTERIOR LIGHTING: This bulletin explains how to install a light at the entrance door.
  • MI18-21 - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-16A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information presents guidelines to help with the diagnosis of the bosch hd10 alternators
  • WB18-15 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, the instrument cluster software must be updated. This mandatory cluster software update will raise the primary and secondary air system ?Low pressure warning? Set point.
  • SP18-13D - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, proceed to the replacement of the drag link.
  • IS-17905 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-13009B - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install and adjust drag link # 660699
  • WB15-19H - EQUIPMENT:APPLIANCE:AIR CONDITIONER: This bulletin explains how to add a reinforcement bracket to bitzer a/c compressor to increase the installation stiffness and reduce vibration amplitude.
  • SP18-13E - STEERING:LINKAGES:DRAG:LINK:CONNECTION: On the vehicles affected by this bulletin, replace the drag link.
  • SP17-314 - INTERIOR LIGHTING: This bulletin explains how to install a light at the entrance door.
  • MI18-02 - ENGINE AND ENGINE COOLING: This mainteannce informaiton presents the latest engine oil & filter change intervals for the volvo engine
  • MI16-17F - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • SP14-309 - BRAKES (PWS): On the vehicles affected by this special bulletin, replace the two visual brake wear indicators on the tag axle.
  • WB14-08C - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, verify the revision numbers of the steering wheel gateway module and multiplex software. If applicable, replace with the latest version. A power source improvement is also required. On some vehi
  • MI1434C - VEHICLE SPEED CONTROL:CRUISE CONTROL: This maintenance information presents how to align the prevost aware adaptive cruise braking (acb)flr20 radar sensor.
  • WB14-06G - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, perform the following verifications and modifications on the a/c system: bulletin is divided in five steps, refer to detailed instructions below. Step 1: unloader replacement (step moved to war
  • WB14-28E - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, replace the ltd, relocate and replace the ir sensor as described in the following procedure.
  • SP14-306D - ENGINE (PWS): On the vehicles affected by this bulletin, replace the engine harness as described in the following procedure.
  • MI1423 - ELECTRICAL SYSTEM:SOFTWARE: A new software version (v1.06) is available to update the cantrak (tire pressure monitoring system) module. This new version will allows a 10 min. Delay before the ?System error not all tires monitored? Message appears in the vehicle clust
  • SP14-30 - WHEELS:LUGS/NUTS/BOLTS: On the identified drive axles, the wheel nut may not be secured by the locking tab.
  • WB14-27 - SUSPENSION: On the vehicles affected by this bulletin, interference may occur between a cable bundle and part of the drive axle surrounding structure when suspension is completely lowered.
  • SP13-52 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN: Risk of premature failure of top fan support due to absence of weld. In the engine compartment above radiator, inspect support to make sure support has two welds in the corners.
  • SP13-34A - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, a relay needs to be added to allow the def to return to the tank after turning the key to the off position. In addition, the acm & mcm need to be reprogrammed to the latest version.
  • SP13-22 - STRUCTURE:FRAME AND MEMBERS: Radius rod support weld inspection: weld beads may be too small on radius rod supports on rear sub-frame.
  • IS11015B - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to replace power relay p/n 561991 with improved power relay p/n 564218 and relay base p/n 564210
  • SP15-340B - STEERING: On the vehicles affected by this bulletin, replace the hardware on the sway bar clamps of the steer and drive axles.
  • SP15-343D - SEATS: On the vehicles affected by this bulletin, replace the hardware on the sliding door of the wheelchair seating area.
  • MI15-51 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: This maintenance information explains how to run a n air conditionning performance test
  • SP15-345 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a software update of the actia tachometer at the rear of the vehicle.
  • WB15-50 - EQUIPMENT:OTHER:LABELS: On the vehicles affected by this bulletin the rear junction box decal located in the right engine compartment is displaying incorrect information regarding the r34 relay voltage. Specifically, the r34 relay should be identified as a 24 v
  • MI15-61 - ENGINE (PWS): This maintrenance infomration explains that the castrol syntrans oil isn?T fully approved for 500 000 miles (800 000 km) extended drain intervals on the volvo i-shift transmission. For this reason, this oil has been downgraded to regular d
  • IS-15907A - EQUIPMENT:MECHANICAL: This instruction sheet explains how to assemble the bendix flr10 and flr20 radar sensor alignment tool
  • SP15-346B - VISIBILITY:WINDSHIELD WIPER/WASHER: On the vehicles affected by this bulletin, the windshield washer bottle may not be identified.
  • SP15-324D - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • SP15-341 - ELECTRICAL SYSTEM:HORN: On the vehicles affected by this bulletin, replace the horn support by 140034.
  • SP15-343B - STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS: On the vehicles affected by this bulletin, replace the hardware on the sliding door of the wheelchair seating area.
  • IS-15012 CO24 - ENGINE (PWS): This instruction sheet explains how to install a "t" key on curbside engine compartment door
  • IS-14152 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: This instruction sheet prvides a road side and workshop instructions for replacing 040949 6mm def hose to a 4mm id hose.
  • SP15-331A - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, replace the two auxiliary equipment decals in the first two road side parcel rack compartments.
  • SP15-340 - STEERING: On the vehicles affected by this bulletin, replace the hardware on the sway bar clamps of the steer and drive axles.
  • MI15-41 - EXTERIOR LIGHTING:TAIL LIGHTS: This maintenance information reminds prevost customers that cleaning products designed for external washing of vehicles should be used for exterior vehicle wash and in particular, for the washing of polycarbonate taillights.
  • MI15-43 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on prevost vehicles equipped with bosch hd10 alternators.
  • MI15-18 - EQUIPMENT: This maintenance information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.
  • SP15-329 - ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL: On the vehicles affected by this bulletin, ?Fast idle? And ?Cancel first reading lamp? Switches on the dashboard may not be wired to provide back-lighting. Modify the wiring to add the feature.
  • MI15-24 - EQUIPMENT:MECHANICAL: This maintenance information explains how to perform an inspection of the vehicle power cables. Power cables in poor condition can be the cause of failures and serious damages in the engine compartment.
  • SP15-304D - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: On the vehicles affected by this bulletin, the bosch hd10 alternators need to be replaced with new bosch hd10plbh 150 amps alternators.
  • SP15-321 - WHEELS: On the vehicles affected by this bulletin, modify the hubodometer support to allow the wheel to be taken out without removing the support.
  • SP15-317 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, replace sun visor on the left side of the driver?S seat by an updated version.
  • SP15-323 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, install a diffuser pipe thermal insulating wrap to promote higher exhaust temperature at the ahi nozzle tip.
  • SP15-16A - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, inspect the rear junction box connections; clean terminals and apply black color guard or termin8r lubricant following the procedure below.
  • WB15-14 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, the end of the exhaust diffuser drain tube may not be properly attached.
  • WB15-10 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, inspect the lower oil fill tube flexible tube. If it is made of black material (edpm), replace tube. Green and blue silicone hoses are accepted.
  • IS-15003A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to use the bosch hd10 24v-150a altenrator conversion kit
  • SP15-314 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, the end of the exhaust diffuser drain tube may not be properly attached.
  • SP15-15A - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform software updates of the engine management system (ems) and instrument cluster. The cluster update affects the beep sound level. Some vehicles will need both systems updated. Other vehicles
  • SP15-320 - EQUIPMENT: On the vehicles affected by this bulletin, inspect the side of the matte finish on the anti-glare shield
  • IS-13169A - BRAKES (PWS): This instruction sheet explains how to install the aware adaptive cruise braking (acb) flr20 radar sensor replacement kits # 145372 and 145373
  • IS-17907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the volvo electronic logging device (eld)
  • SP17-314 - INTERIOR LIGHTING: On the vehicles affected by this bulletin, install a light at the entrance door.
  • SP17-313 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, replace the batteries by a new set (4) of the same model; perform several verifications on the alternator and charging circuit. Finally, update the multiplex software to the latest version and disa
  • IS-17071 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • wb17-16 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, remove selected wires from c15 and c58 of the hvac system wiring, and place them in new connectors c15b and c58b. New connectors have a higher amp rating. We recommend inspecting connectors c15 & c
  • Sp18-300 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This bulletin explains how to replace ceiling transition pannels, when needed
  • MI17-22 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: This maintenance information explains how to inspect the fuel tank cradle mounting screws on a yearly basis
  • SP15-310 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, protect the a/c suction hose (issue "a") and modify the pipe clamp arrangement above the battery box (issue "b").
  • SP15-312 - STRUCTURE:BODY:DOOR : On the vehicles affected by this bulletin, the entrance door may open inadvertently or not open at all when door open button is pressed.
  • SP15-304B - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: On the vehicles affected by this bulletin, the bosch hd10 alternators need to be replaced with new bosch hd10plbh 150 amps alternators.
  • WB15-13 - SUSPENSION: On the independent front suspension level valve linkage of the vehicles affected by this bulletin, a control rod may come in contact with an air reservoir outlet when vehicle rises from low to high buoy. As a result, the vehicle may be leve
  • SP15-309 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: On the vehicles affected by this bulletin, inspect the bosch hd10 alternator connections.
  • SP15-302 - EQUIPMENT:MECHANICAL: On the vehicles affected by this bulletin, perform the replacement of the kneeling alarm buzzer assembly.
  • SP15-307 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: On the vehicles affected by this bulletin, tighten the alternator return pulley mounting bolt to a specific torque.
  • SP15-306 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, connect a tube and muffler to the kneeling valve exhaust and route it to the spare tire compartment.
  • SP15-301 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, inspect fare box harness connector a132b pin out.
  • SP15-300 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: On the vehicles affected by this bulletin, replace the radiator fan driveshaft by an improved version having a stronger rubber protector.
  • MI15-02 - POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT: This maintenance information presents an improved differential breather kit, identical to the one now used in production. This new breather incorporates a "j" shaped hose that prevents oil leakage and water ingestion while allowing the axle
  • WB14-47B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a software update of ecm (engine control module) and acm (aftertreatment control module) to provide improved temperature-related behaviour. The software will also change urea dosing valve b
  • Wb15-19F - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • Mi16-15 - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • SP16-304 - EQUIPMENT:OTHER:LABELS: On the vehicles affected by this bulletin, replace the battery connection decal by a new version.
  • IS-14154 - FUEL SYSTEM, GASOLINE: This instruction sheet explains how to modify the support beam (part # 30022 installation)- as part of the x3 fuel tank installation
  • WB17-02 - ENGINE AND ENGINE COOLING: This bulletin explains how install an extension to the linear thermal detector (ltd) over the alternators
  • SP17-307 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: This bulletin explains how to replace the radiator door upper hinge
  • SP17-303D - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, replace two idlers by an improved version on the alternator drive belt and on the a/c belts.
  • IS-16100 - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: This instruction sheet explains how to install latest radio models
  • IS-16048 - LATCHES/LOCKS/LINKAGES: This instruction sheet explains how to install a wcl manual lock
  • IS-15003D - ELECTRICAL SYSTEM: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • Sp16-323 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, change a parameter in the mux system to deactivate a dtc corresponding to air dryer cartridge change warning.
  • MI16-32 - POWER TRAIN:DRIVELINE:CENTER SUPPORT BEARING: Explains that improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • MI15-43A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on prevost vehicles.
  • SP15-339 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, replace hardware on the aisle step curb side nosing.
  • WB15-19 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • SP15-331 - EQUIPMENT: On the vehicles affected by this bulletin, replace the two auxiliary equipment decals in the first two road side parcel rack compartments.
  • SP15-318 - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: On the vehicles affected by this bulletin, replace the battery box decals.
  • SP15-336C - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : On the vehicles affected by this bulletin, five foot switches might be working intermittently and needs to be replaced.
  • SP15-323B - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, install a diffuser pipe thermal insulating wrap to promote higher exhaust temperature at the ahi nozzle tip.
  • WB15-10A - ENGINE (PWS): On the vehicles affected by this bulletin, inspect the lower oil fill tube flexible tube. If it is made of black material (edpm), replace tube. Green and blue silicone hoses are accepted.
  • SP15-335A - STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS: On the vehicles affected by this bulletin, replace the power steering supply hose.
  • WB15-26B - SUSPENSION:REAR:SPRINGS:AIR SUSPENSION SYSTEM: On the vehicles affected by this bulletin the brake hose may come in contact with the air spring support when the front axle is in low or high position, either by kneeling or low-high buoy. Perform an inspection. Depending on the result, ad
  • SP15-332 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, change the lower blind guide supports for a new style with two anchor screws.
  • SP14-324B - STRUCTURE:BODY:BUMPERS: On the vehicles affected by this bulletin, replace the front bumper retaining spring.
  • SP15-15B - ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL: On the vehicles affected by this bulletin, perform software updates of the engine management system (ems) and instrument cluster. The cluster update affects the beep sound level. Some vehicles will need both systems updated. Other vehicles
  • SP15-317A - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, replace sun visor on the left side of the driver's seat by an updated version.
  • WB15-13A - SUSPENSION:REAR:SPRINGS:AIR SUSPENSION SYSTEM: On the independent front suspension level valve linkage of the vehicles affected by this bulletin, a control rod may come in contact with an air reservoir outlet when vehicle rises from low to high buoy. As a result, the vehicle may be leve
  • SP15-320A - STRUCTURE:BODY: On the vehicles affected by this bulletin, inspect the side of the matte finish on the anti-glare shield
  • SP15-310A - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, protect the a/c suction hose (issue "a") and modify the pipe clamp arrangement above the battery box (issue "b").
  • SP15-325B - STRUCTURE:BODY:DOOR : On the vehicles affected by this bulletin, perform various improvements on the bi-fold door mechanism.
  • Sp17-312A - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: On the vehicles affected by this bulletin, bus washing operations can result in water dripping into the front service compartment. Add a drip guard above the entrance door valve.
  • CK17-27 - EQUIPMENT ADAPTIVE/MOBILITY: This conversion kit explains how to to disable the acb radar.
  • SP16-43A - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, coolant may leak by the coolant level sensor wires on the surge tank. Replace the sensor with an improved version.
  • SP16-326 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, re-torque the clamps on specific coolant hoses of the cooling system.
  • SP16-311B - EQUIPMENT: On the vehicles affected by this bulletin, add two clips to secure the direct light lenses, 13 lenses per vehicle.
  • IS-15003B - EQUIPMENT: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • SP14-17 - WHEELS:LUGS/NUTS/BOLTS: Inspect the wall anchor bolts. Make sure the washers under bolt head are locking washers and not flat washer.
  • IS-14900 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to replace 562489 dimmer, using kit #069136
  • MI16-15B - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • Sp16-309A - ENGINE (PWS): On the vehicles affected by this bulletin, secure the mounting of the curb side engine door electrical fan.
  • Wb16-29 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available. This update must be carried out by qualified technicians. As soon as possible, make an appointment with your nearest prevost service cen
  • Sp16-317 - BRAKES (PWS): On the vehicles affected by this bulletin, it is necessary to ensure proper brake pedal installation and adjustment following the procedure below.
  • IS-16902 - BRAKES (PWS): This instruction sheet explains how to install and adjust brake pedal kit is16902
  • MI16-14 - SUSPENSION: Use this procedure when a suspension height check or adjustment must be performed.
  • Mi16-28 - VISIBILITY:REARVIEW MIRRORS/DEVICES: This maintenance information explains that on vehicles equipped with ramco rear-view mirrors in winter conditions, ice may accumulate in the gap between the glass bottom edge and shell. The ice may impede mirror adjustment. Installing a dri
  • SP16-306A - WHEELS: On the vehicles affected by this bulletin, replace an access panel aft of the tag axle wheel, road side.
  • Sp16-302A - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK ASSEMBLY: On the vehicles affected by this bulletin, replace the pressure cap on the surge tank.
  • Sp16-313A - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, coolant may leak by the coolant level sensor wires on the surge tank. Replace the sensor with an improved version.
  • Sp16-311A - EQUIPMENT: On the vehicles affected by this bulletin, add two clips to secure the direct light lenses, 13 lenses per vehicle.
  • SP16-21 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, perform the proactive replacement of the lower hinges for both service doors.
  • SP16-306 - WHEELS: On the vehicles affected by this bulletin, replace an access panel aft of the tag axle wheel, road side.
  • MI16-23 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information explains that decals are available to update the front junction box on 2013 to 2016 prevost vehicles; the decals will provide updated information and component descriptions. Refer to the identification part of t
  • SP16-25 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin install an updated proximity switch on the vehicle compressor door following instruction sheet is-12026.
  • MI16-15A - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • MI16-10 - WHEELS: This information letter applies only to vehicles equipped with 19000 lb independent front suspension (ifs) and 22.5 x 10.5 alcoa aluminum wheels for 365/70 r 22.5 size tires. When balancing this wheel for installation on the ifs, a specifi
  • Sp16-309 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, secure the mounting of the curb side engine door electrical fan.
  • MI16-16 - ELECTRICAL SYSTEM: This procedure explains how to perform a starter removal and installation, and does apply to melco 105p70 starter part number #21212425.
  • SP15-304E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: On the vehicles affected by this bulletin, the bosch hd10 alternators need to be replaced with new bosch hd10plbh 150 amps alternators.
  • WB15-55 - POWER TRAIN:AXLE ASSEMBLY: On the vehicles affected by this bulletin, inspect the gap between the radius rod support and the front axle. A deviation in the axle beam envelope can lead to interference between the two parts. In most cases, slightly moving the support w
  • SP16-302 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, replace the pressure cap on the surge tank.
  • MI16-05 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information shares information about the bendix m-32qr valve replaced by m-40qr model htat need to be taken into consideration, specially when switching them for the first time on a vehicle.
  • Sp17-313 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, replace the batteries by a new set (4) of the same model; perform several verifications on the alternator and charging circuit. Finally, update the multiplex software to the latest version.
  • CK17-19A - EQUIPMENT: This conversion kit explains how to remove tgw1 from vehicles using tech tool, no manual vda changes needed. This conversion kit will work for any vehicle equipped with tgw1 up to the vin's listed on the bulletin.
  • SP15-341C - ELECTRICAL SYSTEM:HORN: On the vehicles affected by this bulletin, replace the horn support by 140034.
  • WB15-19E - EQUIPMENT: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • SP15-324E - EQUIPMENT: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and r
  • WB17-16 - ELECTRICAL SYSTEM:WIRING: On the vehicles affected by this bulletin, on the hvac system wiring, remove selected wires from c15 and c58 and place them in new connectors c15b and c58b. New connectors have a higher amp rating.
  • SP16-311G - EQUIPMENT: On the vehicles affected by this bulletin, add z clips to secure the direct light lenses, 13 lenses per vehicle.
  • IS-15003D - ENGINE (PWS): This insruction sheet explains how to insall the bosch hd10 24v-150a alternator conversion kit ? Twin bosch mounted on volvo d13 engine
  • sp17-310 - STRUCTURE:BODY:DOOR : On the vehicles affected by this bulletin, it is necessary to replace the two engine door latch pins and the compressor door latch pin by new units made of sturdier material.
  • Sp17-312 - STRUCTURE:BODY:DOOR : On the vehicles affected by this bulletin, bus washing operations can result in water dripping into the front service compartment. Add a drip guard above the entrance door valve.
  • Sp17-311 - STRUCTURE:BODY:DOOR : On the vehicles affected by this bulletin, replace connector c12 installed inside the dpf access door with an improved version providing a better seal.
  • IS-15113 - STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS: This instruction sheet explains how to proceed to the 7 pivots luggage door hinge replacement
  • SP14-323 - SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES: On the vehicles affected by this bulletin, replace the brake pedal assembly.
  • SP14-335 - POWER TRAIN:AXLE ASSEMBLY: On the vehicles affected by this bulletin, add a support on the curbside of the drive axle.
  • SP14-334 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, install a lanyard on each of the two overhead access panels in the front section of the bus interior.
  • SP14-332 - POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES: On the vehicles affected by this bulletin, inspect the transmission oil cooler to make sure it is properly secured. In certain material conditions, the bolts may extend beyond the threaded length of the mounting holes in the cooler creating
  • SP14-331A - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, replace the various bus bars and place one insulation sheet beside the breaker plate
  • SP14-330 - LIGHTING (PWS): On the vehicles affected by this bulletin, replace the imron painted marker light guards with powder coated marker lights.
  • SP14-324B - STRUCTURE:BODY:BUMPERS: On the vehicles affected by this bulletin, replace the front bumper retaining spring.
  • SP14-325 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, add a new engine compartment curbside door and a temperature probe behind the alternators along with corresponding wiring additions and updates.
  • SP14-322 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, add or replace insulating sheets in the rear electrical compartment and battery box.
  • SP14-320B - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, perform a software update of ecm and acm to modify the dosing strategy. The software will also improve urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the u
  • SP14-326 - ENGINE (PWS): On the vehicles affected by this bulletin, the compressor belt may not be tensioned properly since the reduction of the diameter of the pulley on the commuters.
  • SP14-318 - STEERING: On the vehicles affected by this bulletin, the steering wheel shaft joint angles are different from the intended design values due to a parts shortage. Replace the steering wheel shaft with the components specified on the bill of material.
  • SP14-317A - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, identify the live wires in the rear electrical compartment according to instructions.
  • SP14-316 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, replace the exhaust pipe thermal insulation blankets.
  • WB14-47B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a software update of ecm (engine control module) and acm (aftertreatment control module) to provide improved temperature-related behaviour. The software will also change urea dosing valve b
  • SP14-315 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, change the connection arrangement behind circuit breaker cb2.
  • WB14-45C - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin remove the acm relay and base identified r49. Reconnect the 24v power wire and protect the remaining signal wires with shrink tube.
  • IS-13169 - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: This instruction sheet explains how to install the aware adaptive cruise braking (acb) flr20 radar sensor replacement kits # 145372 and 145373
  • SP14-46 - EQUIPMENT ADAPTIVE/MOBILITY: This bulletin is performed on a fix as fail basis. On the vehicles affected by this bulletin, update to the latest configuration of wiring and sensors for the bitzer compressor.
  • WB14-44B - EQUIPMENT:ELECTRICAL: On the vehicles affected by this bulletin, changing of vecu (vehicle electronic control unit) parameters is necessary. This update must be carried out by qualified technicians. Make an appointment with your nearest prevost service center.
  • SP14-313 - SERVICE BRAKES, HYDRAULIC: On the vehicles affected by this special bulletin, a 7psi pressure switch must be added to the transmission retarder circuit to activate the retarder when vehicle brakes are applied, increasing drivetrain components reliability.
  • WB14-42A - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a power source improvement and a multiplex software update for the steering gateway module. On a limited number of vehicles, the module will be replaced with the latest version of the part.
  • WB14-37 - EQUIPMENT:OTHER:LABELS: On the vehicles affected by this bulletin, replace the engine info label for an updated version. H series vehicles require two labels. X-series vehicles require only one label.
  • WB13-65D - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, software updates with enhancements are available for the multiplex system, for the ems and aftertreatment control module (acm). On all vehicles, perform a dpf service regeneration and crystal subli
  • WB13-58 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, change the flexible hose at the engine air intake
  • WB13-63A - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, inspection and replacement of 70 amp circuit breakers in the rear electrical compartments is required.
  • WB13-62B - POWER TRAIN: On the vehicles affected by this bulletin, torque must be verified on one of the axle support mounting bolts. An interference of a production tool with the casting on the nut side of the fastener may have resulted in lower effective torque.
  • WB13-55A - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, the upper support of the tripod fan support must be inspected for the presence of weld. If no weld is found, it must be replaced.
  • Sp16-320 - STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS: On the vehicles affected by this bulletin, the compressor door support to the vehicle must be improved by the addition of a lower support bracket and the replacement of the two door hinges. A support plate must also be riveted to the door
  • MI16-17E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternator.
  • Sp16-326B - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: On the vehicles affected by this bulletin, re-torque the clamps on specific coolant hoses of the cooling system.
  • IS-15003C - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • WB17-06 - EQUIPMENT:MECHANICAL: On the vehicles affected by this bulletin, replace the existing wheelchair lift control pendant support by an improved version.
  • WB15-19G - EQUIPMENT: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • SP16-319B - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, replace the pitman arm nut and re-torque to specification.
  • MI16-34 - ELECTRICAL SYSTEM: "this maintenance information describes the steps to be followed on your computer to add the volvo engine brake auto mode on the vehicle. The auto mode may be added on us10 and obd13 vehicles that were built before the introduction of the
  • WB15-10 - ENGINE (PWS): Summary to be provided on a future date.
  • SP15-340 - EQUIPMENT: Summary to be provided on a future date.
  • SP15-336C - EQUIPMENT: Summary to be provided on a future date.
  • SP15-335A - STEERING: Summary to be provided on a future date.
  • SP15-325 - EQUIPMENT: Summary to be provided on a future date.
  • SP15-312 - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: Summary to be provided on a future date.
  • SP-15-336C - EQUIPMENT: Prevost: due to intermittently working, the five foot switches, on some buses, will be replaced. Model 2014-15 x3-45. *pe
  • SP-15-335A - STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS: Prevost: the supply hose for power steering needs be replaced on some buses. Model 2014-15 x3-45. *pe
  • SP-15-328 - SERVICE BRAKES, AIR:SUPPLY:HOSES, LINES/PIPING, AND FITTINGS: Prevost: when bus in position of low or high buoy, brake hose will contact air spring support and would need inspected and adjusted, for hose to not interfere. Model 2012-15 x3-45. *pe
  • SP-15-309 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: Prevost: bosch hd 10 alternator connections, on some buses, need to be inspected and may need other parts and materials, if required. Model 2011-14. *pe
  • SP-15-325 - STRUCTURE:BODY:DOOR : Prevost: on some buses, the bi-fold door mechanism needed various improvements performed on it. Model 2014-15 x3-45. *pe
  • SP-15-312 - STRUCTURE:BODY:DOOR : Prevost: when button to door is pressed to open, entrance door, on some buses, inadvertently, will open and not open at all. Model 2014-15 x3-45. *pe
  • WB-15-13 - SUSPENSION:FRONT: Prevost: warranty issued, on some buses, regarding control rod of independent front suspension level valve, contacting air reservoir outlet when going low to high buoy. Model 2012-15 x3-45. *pe
  • SP-15-16 - EQUIPMENT: Prevost: rear junction box connections need inspected with clean terminals and termin8r lubricant or black color guard should be applied following required procedure. Model 2011-14 x3-45 (gli). *pe
  • SP-15-340 - EQUIPMENT: Prevost: information provided on certain buses, the sway bar clamps of steer and drive axles need hardware replaced. Model 2014-15 x3-45 commuter. *pe
Known Recall Investigations
  • Alternator front bearing failure investigation # PE21011

    Nhtsas office of defects investigation (odi) opened a preliminary evaluation after reviewing field reports concerning alternator front bearing failures that cause elevated temperatures within the engine compartment, resulting in the fire suppression system (fss) activating, immediately shutting the engine down, and rendering the bus inoperable.Analysis of the data provided by prevost car (us) inc. Showed high failure frequency and thermal events. An immediate shutdown of the bus can increase the risk of a crash or injury of bus occupants. In response to this investigation, prevost car (us) inc. And volvo bus corporation decided to conduct recalls 22v-221 and 22v-222. By submitting part 573 defect information reports on april 6, 2022, prevost car (us) inc. And volvo bus corporation notified odi of a safety defect in certain model year (my) 2010-2023 prevost h3-45; x3-45; x3-45 com; h3-45 vip: x3-45 vip and 2020 volvo 9700 vehicles; some of these buses may have experienced thermal events after failure of the alternator front bearing, because the alternator belt continues to turn the alternator after the bearing failure.These recall actions address the safety concern that led to the opening of this investigation.Therefore, with these recall actions, this investigation is closed. The recalls encompass all model and my vehicles addressed by the investigation. However, the closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist in other model or my vehicles outside of the recall scope. The agency reserves the right to take further action if warranted by the circumstances.

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.