Toyota Avalon Hybrid 2016

• Recall 150619 [USA]: In the event of a crash, air bags and/or seat belt pretensioners that do not deploy as intended may increase the risk of injury.
  Toyota motor engineering & manufacturing (toyota) is recalling certain 2011-2019 corolla, 2011-2013 matrix, 2012-2018 avalon, and 2013-2018 avalon hybrid vehicles. During certain crashes, the air bag electronic control unit (ecu) may malfunction, possibly disabling the deployment of the air bags and/or seat belt pretensioners.
  toyota will notify owners, and dealers will inspect the ecu and install a noise filter between the air bag control module and its wire harness, as necessary, free of charge. Owners were notified of the safety risk beginning march 2, 2020. A second letter notifying owners of the remedy repair will be mailed between march 16, 2020 and june 27, 2020. Owners may contact toyota customer service at 1-888-270-9371. Toyota's numbers for this recall are 20tb03, 20ta03 and 20ta05.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 125956 [USA]: A front driveshaft separation would result in a loss of propulsion while driving, and if the driver exits the vehicle without applying the parking brake, the vehicle may roll. both scenarios can increase the risk of a crash.
  Toyota motor engineering & manufacturing (toyota) is recalling certain 2016 camry hybrid and avalon hybrid vehicles. The front drive shaft may separate.
  toyota will notify owners, and dealers will check the serial number of the vehicle's drive shaft, replacing any that are affected, free of charge. The recall began on august 11, 2017. Owners may contact toyota customer service at 1-800-331-4331. Toyota's number for this recall is h0m.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 124096 [USA]: If the air bag was installed with incorrect fasteners, the fasteners may become loose over time, affecting the air bag deployment and increasing the risk of injury.
  Toyota motor engineering & manufacturing (toyota) is recalling certain model year 2016 avalon, and 2017 camry vehicles manufactured august 3, 2016, to september 12, 2016. The front passenger knee air bag module may have been attached to the lower instrument panel with incorrect fasteners.
  toyota will notify owners, and dealers will inspect the fasteners, and if necessary, replace the instrument panel brace and body bracket and reattach the air bag assembly, free of charge. The recall began on february 8, 2017. Owners may contact toyota customer service at 1-800-331-4331. Toyota's number for this recall is g05.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 113251 [USA]: Air bags that do not deploy as intended during a crash increase the risk of injury.
  Toyota motor engineering & manufacturing (toyota) is recalling certain model year 2016 avalon and camry vehicles manufactured november 30, 2015 to march 4, 2016. The occupant classification system (ocs) that activates or deactivates the front passenger seat air bag system may have been improperly calibrated. As a result, the front passenger air bag and the front passenger knee air bag may not deploy as intended in certain crash scenarios. As such, these vehicles fail to comply with federal motor vehicle safety standard (fmvss) number 208, "occupant crash protection."
  toyota will notify owners, and dealers will recalibrate the ocs, free of charge. The recall began by may 13, 2016. Owners may contact toyota customer service at 1-888-270-9371. Toyota's number for this recall is g0j.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 2021723 [Canada]: Accessories
  Issue: this recall is for certain block heater kits installed on certain vehicles or sold as accessories at toyota or lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: this recall only affects the following block heater/cord part numbers: C014003034 pk5a408j09 pU14000904 C014003151 pk5a408j13 pU14000905 C014000885 pk5a489j11 pU14000907 C014000888 pk5a489j22 pU14000909 C014000907 pk5a410h00 pU14000911 C014100904 pU14000900 pU14000913 C014100907 pU14000901 pU14003571 C014100911 pU14000902 pk5a408j05 pU14000903 safety risk: engine block heater wiring that overheats or melts could create the risk of a fire. Corrective actions: toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.

  Show Content

• Recall 2020013 [Canada]: Airbag
  Issue: on certain vehicles, the circuits within the airbag control module could be damaged in a crash. This could cause the airbags and seat belt pretensioners to not deploy in certain crashes. Safety risk: airbags or seat belts that do not work properly in a crash could create an increased risk of injury. Corrective actions: toyota will notify owners by mail and instruct you to take your vehicle to a dealer to install an electrical noise filter to prevent damage to the airbag control module.

  Show Content

• Recall 2017363 [Canada]: Electrical
  On certain vehicles, the electrical power cords of some dealer installed block heaters may have been improperly manufactured, causing the wires to contact each other, resulting in a short circuit. A short circuit could lead to a fire which would increase the risk of injury and/or damage to property. Correction: for vehicles where the subject block heater was approved for installation, the dealer will replace the block heater assembly with a new one of an improved design. For vehicles where the subject block heater was not approved for installation, dealers will remove the block heater assembly. In the interim, until the remedy can be performed, dealers will cut the plug end from the block heater cord to disable the block heater's operation.

  Show Content

• Recall 2016160 [Canada]: Airbag
  Certain vehicles may not comply with the requirements of canada motor vehicle safety standard (cmvss) 208 - occupant protection in frontal impacts. The front passenger seat's occupant classification system (ocs) may not have been calibrated properly during the manufacturing process. This could result in the non-deployment of the front passenger air bag and the front passenger knee airbag, which would increase the risk of injury to the seat occupant in a crash where airbag deployment is warranted. Correction: dealers will re-calibrate the occupant classification system.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Pedestrian alert sounds investigation # DP22005

  Nhtsa received a petition on or about july 18, 2022, requesting that federal motor vehicle safety standard (fmvss) 141 be applied to all electric and hybrid vehicles operating in the united states. The petition can be reviewed at nhtsa.Gov under odi number 11486072.Fmvss 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 kg or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after march 1, 2021.The petitioner asserts that hybrid and electric vehicles to which the standard does not apply should be found to contain a safety defect. In support of the petition, the petitioner includes findings contained in a bill introduced in the house of representatives in 2009, the pedestrian safety enhancement act of 2009, h.R. 734, 111th cong. (2009). A related bill, the pedestrian safety enhancement act of 2010, became law in january 2011 (pub. L. 111-373). The petitioner requests that nhtsa require all electric and hybrid vehicles comply with fmvss 141, regardless of production date.The defect petition has been opened to evaluate the issue and determine whether to grant or deny the petition.The associated product list is not exhaustive and may contain vehicles that are equipped with pedestrian alert sounds.
  

  Show Content

• Air bag acu electrical overstress investigation # EA19001

  The office of defects investigation (odi) is expanding the investigation to include the equipment supplier and vehicle manufacturers (oems) using this unit.The investigation focuses on acus manufactured by trw, now zf-trw (zf) , the tier-one supplier to hyundai and kia and the other affected oems.The acu senses a vehicle crash to determine whether air bag deployment is required, and if so, deploys the appropriate air bags and other supplemental restraints.Zf supplied subject acus to six oems: fca, honda, hyundai, kia, mitsubishi and toyota.Internal to the acu is an electronic component (an application specific integrated circuit, or asic) that monitors signals from crash sensors.A failure of the asic may prevent deployment of the required air bags and devices, or may otherwise affect the proper operation of the acu.The acu is located in the passenger compartment, and electrical wiring connects the asic to sensors located at the front of the vehicle.Odi’s current understanding is that a crash event may, in and of itself, produce harmful signals on the sensor wiring capable of damaging the asic, although the probability of this occurring appears to be low.While the acu incorporates electrical circuitry intended to protect the asic from harmful signals, the level and effectiveness of the protective circuitry varies by oem customer.During pe18-003, hyundai and kia filed recalls (18v-137 and 18v-363 respectively) to address a defect that could result in acu disablement and non-deployments.According to the filings, the disablement occurs in certain types of frontal crash events.Both filings discussed a condition known as electrical overstress (eos) that affected the subject asic and was likely caused by electrical signals that entered the acu via sensor wiring.The recalled vehicles used acus that had the lowest levels of asic protection while non-recalled hyundai and kia products using subject acus had higher levels of protection.Odi has not identified any eos failures in the non-recalled kia and hyundai populations.In september 2016, fca filed recall 16v-668 for certain model year (my) 2010 to 2014 chrysler, dodge and jeep products also manufactured with the subject acu.In that filing, fca also discussed an eos condition that resulted in a failure of the subject asic, which caused air bag non-deployment. Fca noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle.Other fca vehicles that also used the subject acu, but not the cross-car harnessing, had not experienced eos failures, despite similar time in service. The recalled fca vehicles used a mid-level form of asic protection.Other fca vehicles that did not use cross car wiring, or used higher levels of asic protection, have not been recalled.Odi has not identified any eos failures in the non-recalled fca population.Recently, odi has identified two substantial frontal crash events (one fatal) involving toyota products where eos is suspected as the likely cause of the non-deployments.The crashes involved a my 2018 and a my 2019 corolla equipped with the subject acu that incorporated higher levels of asic protection.Additionally, both acus were found to be non-communicative (meaning the acu could not be read with an event data recorder) after the crash, a condition found in other cases where eos occurred with other oems.No other eos events have been identified for other toyota products (including corolla models that used the subject acu since my 2011), or for the honda and mitsubishi vehicles that use the subject acu.Odi plans to evaluate the susceptibility of the subject acu designs to electrical signals, as well as other vehicle factors that can either lead to, or reduce the likelihood of, an eos event.Additionally, odi will evaluate whether an unreasonable risk exists that requires further field action.
  

  Show Content

Travel on the street and may hit an object (could be an empty trash container. Vehicle left the travel lane, going up on the sidewalk, stuck 2 garbage cans and through the numerous bushes.

Travel on the street and may hit an object (could be an empty trash container. Vehicle left the travel lane, going up on the sidewalk, stuck 2 garbage cans and through the numerous bushes.

Recall of 1/2020 still has no remedy from manufacturer and no anticipated date of remedy availability (nhtsa recall number 20v024).

Recall of 1/2020 still has no remedy from manufacturer and no anticipated date of remedy availability (nhtsa recall number 20v024).

My car has an sos system that notifies toyota or their contractor if the car has been in an accident, summons law enforcement, tow truck, etc. I do not know what other safety issues are wrapped into it. It has a red warning light that goes on when it stops working. It has been into my local dealer three times to be repaired and each "repair" has failed immediately upon me picking it up again. Today, after the dealer worked on it, the decided that the "cell system" that is built into the car and is under the passenger seat needs to be replaced and will cost $2200.00. I don't know what other "safety systems" are reliant on this dysfunctional safety but i would like for nhtsa to know about this and let me know if it is a hazard for me and others. The red light stays on whenever the car is operated.

My car has an sos system that notifies toyota or their contractor if the car has been in an accident, summons law enforcement, tow truck, etc. I do not know what other safety issues are wrapped into it. It has a red warning light that goes on when it stops working. It has been into my local dealer three times to be repaired and each "repair" has failed immediately upon me picking it up again. Today, after the dealer worked on it, the decided that the "cell system" that is built into the car and is under the passenger seat needs to be replaced and will cost $2200.00. I don't know what other "safety systems" are reliant on this dysfunctional safety but i would like for nhtsa to know about this and let me know if it is a hazard for me and others. The red light stays on whenever the car is operated.

Engine hesitates for a few seconds when starting from a stop or a slow speed in city traffic. The dealer said it was a computer learning process and it should go away. Problems has been around since new in 2016.

The front to back side rubber weatherstripping that moves with the sunroof as it opens and closes continues to fall off. There are two pieces like this, one on the driver's side the other on the passenger's side. The two pieces, each about 18 inches long and two inches wide, look like black rubber small accordions. While driving and opening or closing the sunroof, these strips fall off. Dealer has reinstalled multiple times, but they continue to loosen and fall off with the movement of the sunroof. Sometimes this will occur while driving at high speeds and disrupt the driver, in the last instance i experienced, while going 70mph and falling onto my head and disrupting my vision for a second. The dealer (and i) "fix" this condition by reinstalling the loosened piece. But the problem recurs and, in my view, is a safety hazard. I cannot get the dealer to focus on the seriousness of this problem and the potential jeopardy in which it places drivers. A better fix, than simple re-installation is required.

"takata recall" airbag. I have been dealing with my airbag light and yellow triangle light coming on while driving for 3 days. The first incident occured while i was driving on the highway during the afternoon after dealership hours. 2nd time was driving on the highway and i immediately took my vehicle to the dealership to which they told me my battery was dirty and failing was the reason for the airbag light to come on. 3rd time i was told that my cell phone charger which was never plugged up on any of the times the light came on was the reason. Still dealing with the unresolved issue.

Common OBD-II Error Codes

• C0140 [1] C0140
• C0141 [1] C0141
• U1400 [1] U1400
• P2610 [1] ECM/PCM Internal Engine Off Timer Performance
• C1AB2 [6] C1AB2
• P0A80 [5] Replace Hybrid Battery Pack
• P0A7A [1] Generator Inverter Performance
• P1AC0 [2] P1AC0