Prevost X3-45-coach 2017

Vehicle Details: Recalls, Investigations, Service Bulletins

Below you will find all available information on the 2017 PREVOST X3-45-COACH.

ManufacturerKnown WMI(s)Fuel Type
PREVOST
PREVOST VIN Decoder

Use the box here to look up VINs from PREVOST as well as other manufacturers

#
Frequently Asked Questions
  • Are there recalls for the 2017 PREVOST X3-45-COACH?
     - There are 16 recall(s) for the 2017 PREVOST X3-45-COACH, additional information is below.
NHTSA Mandated Recalls
  • Recall 260234 [USA]: Beacons that do not provide proper illumination may be less visible to wheelchair lift users, increasing the risk of injury.

  • Recall 248159 [USA]: An inoperative engine stop button can increase the risk of injury to a service technician.

  • Recall 191820 [USA]: An overheated alternator bearing can increase the risk of a fire.

  • Recall 147409 [USA]: If the engine unexpectedly shuts down, passengers may have to be transferred to another vehicle on the side of the road, increasing the risk of an injury. if the engine unexpectedly shuts down while the vehicle is in motion, there is an increased risk of crash.

  • Recall 140676 [USA]: If the fire suppression system does not work as intended, it can increase the risk of injury in the event of a fire.

  • Recall 133699 [USA]: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.

  • Recall 138368 [USA]: If the fuel tank separates from the vehicle, it could be a road hazard and the vehicle would stall. either scenario increases the risk of a crash.

  • Recall 122311 [USA]: If the fasteners loosen, the trailer hitch may deform or detach from the vehicle, increasing the risk of a crash.

  • Recall 125169 [USA]: The missing reflex reflectors may reduce the side visibility of the vehicle in certain conditions, increasing the risk of a crash.

  • Recall 122968 [USA]: If the steering arm lever fails, causing a loss of steering, it can increase the risk of a crash.

  • Recall 2019380 [Canada]: Engine

  • Recall 2019084 [Canada]: Accessories

  • Recall 2017570 [Canada]: Accessories

  • Recall 2017476 [Canada]: Fuel supply

  • Recall 2017239 [Canada]: Lights and instruments

  • Recall 2017087 [Canada]: Steering

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • IS-23019 - SUSPENSION: Sway bar collars improvement
  • IS-18106 - STEERING: Kit power steering tank convertion cummins to zf with d13 engine
  • MI16-32 - ENGINE AND ENGINE COOLING: Improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • IS-19912E - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with delco remy alternator. Revision: e note added regarding power cable connection
  • IS-19901E - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with bosch alternator. Revision: e note added regarding power cable connection
  • IS-21072B - ELECTRICAL SYSTEM: Steering gateway. Revision b - pin 2 and 10 were inverted on connector a139
  • MI22-12B - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: b - general update
  • SP18-35J - ENGINE AND ENGINE COOLING: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency. Revision j - range of applicable vins updated.
  • MI22-12A - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: a - erroneous secondary & accessory tanks location.
  • MI22-12 - SERVICE BRAKES, AIR: Air tanks draining sequence
  • IS-17151C - EXTERIOR LIGHTING: Halogen to led fog light replacement kit. Revision: c - advanced kits canceled
  • SP18-35J - ENGINE AND ENGINE COOLING: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency. Revision j - range of applicable vins updated.
  • IS-22902 - WHEELS: Tag axle hub flange - alternate cap screw
  • IS21-072 - ELECTRICAL SYSTEM: Steering gateway, revision a : cancel watch dog removal from efd part of the instruction
  • MI20-08C - EQUIPMENT: Storage and startup guidelines : part number updates
  • IS21-901 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : X3 series envirocare - ions air sanitizer
  • IS21-072A - ELECTRICAL SYSTEM: Steering gateway revision a cancel watch dog removal from efd part of the instruction
  • IS20-925A - VISIBILITY: Central hvac merv filters installation
  • IS22-040 - EQUIPMENT ADAPTIVE/MOBILITY: Brake pedal seal plate installation kit
  • IS21-072 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Steering gateway schematic
  • SP18-35H - EQUIPMENT: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • SP18-35H - EQUIPMENT ADAPTIVE/MOBILITY: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • SP18-39D - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Scr converter replacement - aftertreatment system
  • SP18-35H - EQUIPMENT:MECHANICAL: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • MI18-16B - ELECTRICAL SYSTEM: Bosch hd10 alternator diagnostic guide revision b to avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
  • SP18-35H - POWER TRAIN: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency
  • SR19-31C - EQUIPMENT: Engine control module (ecm) software update - engine cooling strategy in high altitude operation revision c: vin range in application box rearranged for h3 coaches
  • MI21-06 - FUEL SYSTEM, DIESEL: Diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair ⿿ from us10 to newer engine generation
  • SP18-35F - POWER TRAIN: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency rev e: expiration date removed
  • Mi21-07A - WHEELS: Ront & tag axle ⿿ unitized hub bearing end play verification and replacement
  • IS-21901 - EQUIPMENT: X3 series envirocare - ions air sanitizer
  • IS-19912D - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator - x3 series us10 up to ghg17 cooling system
  • IS-19901D - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator
  • IS-18042 - ELECTRICAL SYSTEM: Eberspacher preheater installation in replacement of spheros & valeo preheaters
  • IS-19901C - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator - x3 series us10 up to ghg17 cooling system
  • IS-19912C - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator
  • MI20-08C - STRUCTURE: Storage and startup guidelines: periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, prevost recommends foll
  • IS-20925A - POWER TRAIN: Central hvac merv filters installation reva
  • VBC-PREVOST 4 - EQUIPMENT ADAPTIVE/MOBILITY:VEHICLE CONTROLS:BRAKING: Communication letter from accociate administration for enforcement, nhtsa from prevost subject vehicle brand: prevost (ewr#000650)
  • IS-18091A - STEERING: Tie rod 610052 first installation instructions: use these instructions when replacing the drop joint tie rod on s82, s84 / s84u i-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment ne
  • MI20-19B - ENGINE AND ENGINE COOLING: Introducing a new engine coolant into prevost service center network
  • MI20-19A - ENGINE AND ENGINE COOLING: Rev a: mention added concerning ddc series 60 engine sca requirement
  • MI21-01 - EQUIPMENT: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI21-01 - POWER TRAIN: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • SP18-39C - FUEL SYSTEM, DIESEL: Scr converter replacement - aftertreatment system revision: c expiration date removed 12/22/2020
  • SP18-35E - FUEL SYSTEM, DIESEL: P20EE (diagnostic troubleshooting code) solution - nox conversion efficiency rev e: expiration date removed
  • MI20-19 - EQUIPMENT: Introducing a new engine coolant into service
  • MI18-02A - ENGINE AND ENGINE COOLING: Engine oil & filter change intervals - volvo d13 engine, from us10 revision: a updated for obd20 engines
  • IS-13169A - BACK OVER PREVENTION: SENSING SYSTEM: RADAR: Prevost aware adaptive cruise braking (acb) flr20 radar sensor replacement kit revision a: kit is13169-1 & is13169-2 canceled, use 145373 &145372
  • MI20-14 - VISIBILITY: Prevost driver assistâ¿¢ - windshield replacement equipped with camera
  • IS-20929 - EQUIPMENT: Uv lights installation in ac compartment
  • IS-20929 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Uv lights installation in a/c compartment
  • P103400 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: Pm sensor has detected battery voltage is too high us 2017 emission level prevost units with delco alternators
  • P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • U17_P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • MI20-08B - EQUIPMENT: Storage and startup guidelines revision: b parts added to suggested material 08-10-2020
  • IS-20922 - EQUIPMENT ADAPTIVE/MOBILITY: Sigma passenger seats partition kit
  • MI18-18B - EQUIPMENT: General hoisting and towing procedures revision: b updated 2.1 to show rubber chocks, secure front and rear.
  • MI20-12 - STEERING: Jerky, noisy or hard to turn steering gearbox. Hydraulic end limiter adjustment. All models ⿿ equipped with rb bosch/zf servocom or servocomtronic steering gearbox
  • IS-19901B - EQUIPMENT: Electric fan drive cooling system conversion with bosch alternator revision b: parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal, st,16
  • IS-19912B - ENGINE (PWS): Electric fan drive cooling system conversion with delco remy alternator revision : b parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal,
  • IS-20907 - EQUIPMENT ADAPTIVE/MOBILITY: Plexiglass panel behind driver x3
  • MI20-08A - EQUIPMENT: Storage and startup guidelines: rev a: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
  • IS-19906G - ELECTRICAL SYSTEM: Bosch to delco remy alternator installation, x3-45 with electric fan drive revision g: updated mux parameter value name.
  • MI20-09 - EQUIPMENT: Prevost vehicle disinfection procedure revision a
  • IS-19084 - EQUIPMENT: Accessory air filter replacement replaces 642192
  • U17_P040200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • U02A200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes U02A200 lost communication with reductant quality module
  • U029E00 - ENGINE (PWS): Repair instructions to address fault codes U029E00 lost communication with nox sensor "b"
  • U029D00 - ENGINE (PWS): Repair instructions to address fault codes U029D00 lost communication with nox sensor "a"
  • P256000 - EQUIPMENT: Repair instructions to address fault codes P256000 engine coolant level low
  • P242A15 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P242A15 exhaust gas temperature sensor bank 1 sensor 3 - circuit short to battery or open
  • P20E892 - EQUIPMENT: Repair instructions to address fault codes P20E892 reductant pressure too low - performance orincorrect operation
  • P208464 - EQUIPMENT: Repair instructions to address fault codes P208464 exhaust gas temperature sensor circuit range/performance bank 1 sensor 2 - signal plausibility failure
  • P204A13 - EQUIPMENT: Repair instructions to address fault codes P204A13 reductant pressure sensor - circuit open
  • P204713 - EQUIPMENT: Repair instructions to address fault codes P204713 reductant injection valve control bank 1 unit 1 ⿿ circuit open
  • P203F00 - EQUIPMENT: Repair instructions to address fault codes P203F00 reductant level low
  • P203115 - EQUIPMENT: Repair instructions to address fault codes P203115 exhaust gas temperature sensor bank 1 sensor 2 - circuit short to battery or open
  • P10CE97 - EQUIPMENT: Repair instructions to address fault codes P10CE97 reductant return: no flow detected - componentor system operation obstructed or blocked
  • P107575 - EQUIPMENT: Repair instructions to address fault codes P107575 clutch system - emergency position not reachable
  • P107017 - BRAKES (PWS): Repair instructions to address fault codes P107017 gearbox brake valve (vagb) - circuit voltage above threshold
  • P105998 - POWER TRAIN: Repair instructions to address fault codes P105998 gearbox oil temperature sensor - component orsystem over temperature
  • P054415 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P054415 exhaust gas temperature sensor bank 1 sensor 1 - circuit short to battery or open
  • P052400 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P052400 engine oil pressure too low
  • P040200 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • P029800 - ENGINE (PWS): Repair instructions to address fault codes P029800
  • P021700 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P021700 engine coolant over temperature condition
  • NOx_Conv2 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P207F-00; P20EE-00
  • NOX_Conv1 - EQUIPMENT ADAPTIVE/MOBILITY: Repair instructions to address fault codes P207F-00 - reductant quality
  • FUELFILTER - ENGINE (PWS): Repair instructions to address fault codes P008A-00; P0087-00
  • MI20-09 - EQUIPMENT:OTHER:LABELS: Prevost vehicle disinfection procedure
  • MI20-08 - UNKNOWN OR OTHER: Storage and startup guidelines - all prevost vehicles & volvo 9700
  • IS-20905 - EQUIPMENT: Hand sanitizer dispenser installation
  • IS-19912A - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator - mention added stating to disable ⿿prime⿝; parts added in the kit.
  • IS-19901A - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator - x3 series us10 up to ghg17 cooling system - mention added stating to disable ⿿prime⿝; parts added in the kit
  • MI15-24 - EQUIPMENT ADAPTIVE/MOBILITY: Added: power cables for l.H. Side alternator & fan drive breaker box
  • IS-19901A - ENGINE AND ENGINE COOLING: Revision : mention added stating to disable prime & parts added in the kit.
  • IS-19921A - EQUIPMENT: This instruction sheet explains how to install a seatbelt cutter in the driver's area
  • IS-19066 - SERVICE BRAKES, AIR: This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
  • SCI19-01C - ELECTRICAL SYSTEM: The intent of this procedure is to guide you through the steps required to program a mcm especially for the control of the electric fan drive as required for conversion kit of instruction sheets is-19900, is-19901, is19910, is-19912.
  • IS-19912 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system conversion kit (with delco remy alternators) on x3 vehicles equipped with us10 up to ghg17 engine.
  • IS-19901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system with bosch alternators on x3 series vehicles equipped with us10 up to ghg17 engines
  • IS-17151 - LIGHTING (PWS): This instruction sheet explains how to replace halogen fog light to led's
  • IS-19040A - STEERING: This instruction sheet explains how to replace power steering pump discharge hose (pressure) - #161335p or #160039
  • SP18-35D_English - FUEL SYSTEM, DIESEL: On vehicles with active code P20EE, perform the following checklist and operations.
  • IS-19912 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system conversion kit (with delco remy alternators) on x3 vehicles equipped with us10 up to ghg17 engine.
  • IS-19901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system with bosch alternators on x3 series vehicles equipped with us10 up to ghg17 engines;
  • IS-18091 - STEERING: This instruction sheet explains how to perform the first installation of tie rod 610052 on prevost vehicles equipped with dana s82, s84 / s84u i-beam axles, 1994- today
  • SCI19-20 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the vehicle program has to be upgraded. This allows the intelligent sleep mode (ism) system improvement to prevent batteries drain when ism is enabled. This procedure shows how to generate the vehi
  • Wb19-11 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the vehicle program might need to be upgraded to prevent batteries drain when ism (intelligent sleep mode) is enabled.
  • MI18-45A - POWER TRAIN: Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to is-18091 for installation instruction
  • Mi14-34D - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: Prevost aware adaptive cruise braking (acb) - flr20 & flr21 radar sensor alignment
  • IS-19915 - EQUIPMENT: Mp-1000 multimedia player installation
  • IS-19040 - STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS: Power steering pump discharge hose (pressure) replacement
  • IS-18910 - EQUIPMENT: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-18158 - EQUIPMENT: Toilet drain valve replacement
  • WB19-07 - SERVICE BRAKES, AIR: On the independent front suspension (ifs) of the vehicles affected by this bulletin, check and make sure that there is enough clearance between the brake hoses identified in the procedure and their respective support bracket.
  • SP18-35C_English - ENGINE AND ENGINE COOLING: On vehicles with active code P20EE, perform the following checklist and operations.
  • IS-19909D - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles
  • IS-19906D - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles equipped with electric fan drive
  • IS-19040 - STEERING: This instruction sheet explains how to perform the replacement of the power steering pump discharge hose (pressure) #161335p or #160039, using kit #160127;
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet shows how to install a flap over the diesel filling cap.
  • WB19-02A - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin replace the idler and belt tensioner support on the left side (hot side) of the engine by an improved part, 011213. This applies to installations with bosch or delco remy alternators on the hot side
  • IS-19909A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles
  • SP18-35B_English - ENGINE (PWS): On vehicles with active code P20EE, perform the following checklist and operations.
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet explains how to install a flap over the diesel filling cap
  • IS-17071A - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • SP18-39B - ENGINE (PWS): This special bulletin explains how to perform the replacement of the scr tank, when authorized.
  • MI19-06 - BRAKES (PWS): This maintenance information is published to answer some questions regarding the inverted or ?Trailing? Mounting position of the drive axle brake calipers on prevost vehicles
  • MI19-05 - EQUIPMENT: This maintenance information expains how to adjust p/n 660865, 660699 draglinks
  • IS-17102A - EQUIPMENT: This instruction sheet explains how to install ism (intelligent sleep mode) on x series with prime hardware
  • IS-19909 - ELECTRICAL SYSTEM: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles
  • Sp18-39A - ENGINE AND ENGINE COOLING: This special bulletin explains how to perform the replacement of the scr tank, when authorized.
  • SCI18-46 - EQUIPMENT:ELECTRICAL: This service center instructions explains how to install the prevost ultimate entertainment system
  • Wb17-14B - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the power cable stud adapter on the alternator must be inspected and if needed, replaced.
  • IS-18907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install hatches with fan on x3 vehicles.
  • Sp18-35 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : On vehicles with active code P20EE, perform the following checklist and operations.
  • WB18-04 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available.
  • MI18-37 - POWER TRAIN:AUTOMATIC TRANSMISSION: This maintenance information presents information about the removal or installation of the lang kk73.1 electromagnetic clutch - part of the bitzer (model 4nfcy) air conditioning compressor.
  • MI18-21A - ENGINE AND ENGINE COOLING: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-18A - EQUIPMENT: This maintenance information explains how to tow and hoist prevost vehicles.
  • MI18-05 - ENGINE AND ENGINE COOLING: This maintenance information explains how to install valve assembly 130009 in replacement of valve 641274
  • MI16-17G - ENGINE AND ENGINE COOLING: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • WB18-01A - STRUCTURE: On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
  • WB18-07B - EQUIPMENT: On the vehicles affected by this bulletin, the busbar connected to circuit breaker cb13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper inst
  • Sp18-20 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, replace the ac compressor discharge hose.
  • MI18-18 - EQUIPMENT:MECHANICAL:WRECKER AND WHEEL LIFT DEVICES: This maintenance information explains how to tow and hoist prevost vehicles.
  • IS-18901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the engine belt guard on x3 series vehicles with coolant system electrical fan drive.
  • MI18-21 - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-16A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information presents guidelines to help with the diagnosis of the bosch hd10 alternators
  • IS-18902 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to installa parcel rack door kits
  • WB18-15 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, the instrument cluster software must be updated. This mandatory cluster software update will raise the primary and secondary air system ?Low pressure warning? Set point.
  • WB18-07 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the busbar connected to circuit breaker cb13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper inst
  • IS-17905 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-13009B - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install and adjust drag link # 660699
  • WB18-07A - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the busbar connected to circuit breaker cb13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper inst
  • MI18-02 - ENGINE AND ENGINE COOLING: This mainteannce informaiton presents the latest engine oil & filter change intervals for the volvo engine
  • MI16-17F - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • IS-18901 - ENGINE AND ENGINE COOLING: This instruction sheet explains how to install an engine belt guard
  • IS-15907A - EQUIPMENT:MECHANICAL: This instruction sheet explains how to assemble the bendix flr10 and flr20 radar sensor alignment tool
  • MI15-24 - EQUIPMENT:MECHANICAL: This maintenance information explains how to perform an inspection of the vehicle power cables. Power cables in poor condition can be the cause of failures and serious damages in the engine compartment.
  • IS-13169A - BRAKES (PWS): This instruction sheet explains how to install the aware adaptive cruise braking (acb) flr20 radar sensor replacement kits # 145372 and 145373
  • IS-17907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the volvo electronic logging device (eld)
  • IS-17071 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • IS-17016 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruciton sheet explains how to relocate the rv-3 valve
  • Wb18-01 - LATCHES/LOCKS/LINKAGES:DOORS:LATCH: On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
  • MI17-22 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: This maintenance information explains how to inspect the fuel tank cradle mounting screws on a yearly basis
  • Mi16-15 - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • WB17-02 - ENGINE AND ENGINE COOLING: This bulletin explains how install an extension to the linear thermal detector (ltd) over the alternators
  • IS-16048 - LATCHES/LOCKS/LINKAGES: This instruction sheet explains how to install a wcl manual lock
  • CK17-30 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is now possible to replace the older generation tgw 2.0 (3g network) by the newer 2.1 version (4g the network) using accessory kit 23266301 and the following procedure.
  • MI16-32 - POWER TRAIN:DRIVELINE:CENTER SUPPORT BEARING: Explains that improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • MI15-40A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL: This maintenance information offers an overview of the operation of commuter bi-part doors.
  • CK17-27 - EQUIPMENT ADAPTIVE/MOBILITY: This conversion kit explains how to to disable the acb radar.
  • SP16-43A - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, coolant may leak by the coolant level sensor wires on the surge tank. Replace the sensor with an improved version.
  • MI16-15B - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • MI16-14 - SUSPENSION: Use this procedure when a suspension height check or adjustment must be performed.
  • Mi16-28 - VISIBILITY:REARVIEW MIRRORS/DEVICES: This maintenance information explains that on vehicles equipped with ramco rear-view mirrors in winter conditions, ice may accumulate in the gap between the glass bottom edge and shell. The ice may impede mirror adjustment. Installing a dri
  • MI16-27 - WHEELS: On vehicles operating in muddy road conditions, a road material ring may accumulate and harden inside the tag axle wheel. Depending on the hardness and abrasion potential of the dirt road material, the caliper body wall may wear out and thi
  • MI16-15A - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • MI16-16 - ELECTRICAL SYSTEM: This procedure explains how to perform a starter removal and installation, and does apply to melco 105p70 starter part number #21212425.
  • MI16-05 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL: This maintenance information shares information about the bendix m-32qr valve replaced by m-40qr model htat need to be taken into consideration, specially when switching them for the first time on a vehicle.
  • SP17-24A - EQUIPMENT:ELECTRICAL: On the vehicles affected by this bulletin, update the mux software to the latest version.
  • CK17-26 - ENGINE (PWS): On the vehicles affected by this bulletin, it is now possible to disable the engine brake automatic function by running accessory kit # 23181730.
  • SP17-23 - POWER TRAIN: On the vehicles affected by the bulletin, there is a possibility for the connection of the 12-24 volt power sensor to be reversed in the rear electrical box.
  • SP17-07 - ELECTRICAL SYSTEM: On the vehicles affected by the bulletin, add protection circuit on a switch back of the engine switch engine shut down.
  • SP17-25 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, it is possible that some of the electrical system decals applied to the vehicle structure need to be updated to reflect the current decal type and position currently used in production vehicles. In
  • SP17-24 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update the mux software to the latest version.
  • MI16-10A - SUSPENSION: This maintenance information applies only to vehicles equipped with 19000 lb independent front suspension (ifs) and 22.5 x 10.5 alcoa aluminum wheels for 365/70 r 22.5 size tires. When balancing this wheel for installation on the ifs, a spe
  • IS-13169 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the aware adaptive cruise braking (acb) flr20 radar sensor replacement kits # 145372 and 145373
  • MI16-17E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternator.
Known Recall Investigations
  • Alternator front bearing failure investigation # PE21011

    Nhtsas office of defects investigation (odi) is opening a preliminary evaluation after receiving a tip from a fleet safety manager concerning alternator front bearing failures that cause elevated temperatures within the engine compartment, resulting in the fire suppression system (fss) activating, immediately shutting the engine down, and rendering the bus inoperable. Review of early warning reporting data identified 9 field reports for model year (my)2015 through my2019 h3 and x3 prevost buses, describing alternator failures in any of 3 alternators equipped on the bus. In some cases, a minor fire occurred damaging nearby electrical harnesses. An immediate shut down of the bus can increase the risk of a crash or injury of passengers when transferring to another bus.Odi is opening this investigation to evaluate the cause, consequence, scope and frequency of the alleged defect in the subject prevost buses.

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.