Mitsubishi Outlander 2wd 2016

• Recall 155583 [USA]: If the parking brake operating shafts bind, the parking brakes may not engage or disengage fully. if the parking brakes do not engage properly, the vehicle could rollaway, increasing the risk of a crash.
  Mitsubishi motors north america, inc. (mmna) is recalling certain 2016 outlander and outlander sport vehicles. The rust prevention coating on the rear brake operating shafts could have been peeled off during the assembly process. As a result, water entering the rear brake caliper boot may cause the parking brake operating shafts to corrode and possibly bind.
  mmna will notify owners, and dealers will replace the rear brake caliper assemblies, free of charge. Owner letters were mailed may 4, 2021. Owners may contact mmna customer service at 1-888-648-7820. Mmna's number for this recall is sr-20-005.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 151500 [USA]: An unrestrained occupant has an increased risk of injury in the event of a crash.
  Mitsubishi motors north america, inc. (mmna) is recalling certain 2014-2019 outlander and 2018-2019 outlander phev vehicles. The second-row center seat belt buckle may interfere with the right-side seat belt buckle when the seat backs are folded down. The interference may cause the right-side seat belt buckle cover to come off, making the buckle latch inoperable and unable to restrain an occupant.
  mmna will notify owners, and dealers will modify the second-row center seat belt buckle cover, install a new warning label to the second-row seat support base, and provide a new warning label insert for the owner's manual, free of charge. The recall began september 1, 2020. Owners may contact mmna customer service at 1-888-648-7820. Mitsubishi's number for this recall is sr-20-004.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 141036 [USA]: If the parking brake actuator shaft binds, the parking brake may not engage or disengage fully. if the parking brake does not engage properly, the vehicle may move unexpectedly if it is parked on a slope, increasing the risk of a crash.
  Mitsubishi motors north america, inc. (mmna) is recalling certain 2014-2016 outlander and 2013-2016 outlander sport vehicles. Water may enter the rear brake calipers causing the parking brake actuator shafts to corrode and possibly bind.
  mmna will notify owners, and dealers will inspect the rear brake calipers and replace the parking brake boot and lever or the brake caliper body, as necessary. Dealers will also replace the piston assembly of the rear brake caliper. These repairs will be performed free of charge. The recall is expected to begin march 27, 2018. Owners may contact mmna customer service at 1-888-648-7820. Mmna's number for this recall is sr-18-002.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 127687 [USA]: If the engine stalls, there is an increased the risk of a crash.
  Mitsubishi motors north america, inc. (mmna) is recalling certain 2015-2017 outlander, 2015-2016 lancer and outlander sport, and 2015 lancer evolution vehicles. These vehicles may have defective relays that can result in an engine stall, reduced engine power or the engine overheating.
  mmna will notify owners, and dealers will replace the affected relays, free of charge. The recall began october 24, 2017. Owners may contact mmna customer service at 1-888-648-7820. Mmna's number for this recall is sr-17-005.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 122665 [USA]: If a door opens while the vehicle is being driven, it can increase the risk of injury.
  Mitsubishi motors north america, inc. (mmna) is recalling certain 2016 outlander and outlander sport vehicles. The inside door latch mechanisms may not latch securely in high temperatures, allowing the doors to open while vehicle is in motion.
  mmna will notify owners, and dealers will replace the door latches, free of charge. The recall began august 25, 2017. Owners may contact mmna customer service at 1-888-648-7820. Mmna's number for this recall is sr-17-002.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 125767 [USA]: A hesitation during acceleration can increase the risk of a crash.
  Mitsubishi motors north america, inc. (mmna) is recalling certain model year 2015-2016 outlander sport vehicles and 2016 outlander and lancer vehicles. The affected vehicles are equipped with a constant velocity transmission (cvt) that, in certain driving conditions, may cause a delay in the vehicle accelerating.
  mmna has notified owners, and dealers will reprogram the cvt control unit with modified software, free of charge. The recall began on august 15, 2016. Owners may contact mmna customer service at 1-888-648-7820. Mmna's number for this recall is sr-16-006.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall R/2018/180 [UK]: Parking brake caliper shaft boots incorrectly sealed
  Due to improper sealing of parking brake caliper shaft boots water might penetrate inside and rust the shaft. As the result of continuous use the rust will erode into the internal caliper and the shaft becomes stuck causing decreased parking brake force. Due to improper manufacturing process automatic adjuster for brake pad clearance of rear brake caliper might not work properly. As the result as brake pad wear the clearance is not correctly adjusted and brake force becomes insufficient to hold a vehicle. In the worst case scenario parking brake will not work even though a lever is fully operated and parked vehicle may move.
  anti-rust coating (fluorine) has been applied to parking brake shaft from 27/01/2016 supplied parts & the inspection process for the caliper has been changed from 14/12/2014 supplied parts.

  Show Content

• Recall R/2018/019 [UK]: Ecu relay may overheat and cause ecu to malfunction
  The engine electronic control unit relay may overheat and fail. This could interrupt power supply to the engine and will cause the engine malfunction warning lamp to illuminate. The engine may stall and may not restart.
  on affected vehicles the engine ecu power relay will be replaced with a new relay.

  Show Content

• Recall R/2018/021 [UK]: Door latching mechanism may malfunction in hot temperatures
  The locking mechanism in the door latch assembly may not operate properly in high temperatures. As a result the door may latch correctly and may unintentionally open whilst driving.
  a modified assembly is available and depending on vehicle identification number the remedy is to replace either both o/s door latches or on all four doors.

  Show Content

• Recall R/2018/180 [UK]: Parking brake caliper shaft boots incorrectly sealed
  Due to improper sealing of parking brake caliper shaft boots water might penetrate inside and rust the shaft. As the result of continuous use the rust will erode into the internal caliper and the shaft becomes stuck causing decreased parking brake force. Due to improper manufacturing process automatic adjuster for brake pad clearance of rear brake caliper might not work properly. As the result as brake pad wear the clearance is not correctly adjusted and brake force becomes insufficient to hold a vehicle. In the worst case scenario parking brake will not work even though a lever is fully operated and parked vehicle may move.
  anti-rust coating (fluorine) has been applied to parking brake shaft from 27/01/2016 supplied parts & the inspection process for the caliper has been changed from 14/12/2014 supplied parts.

  Show Content

• Recall R/2018/285 [UK]: The brake hydraulic unit function may be interrupted
  Driver assist programme functions through the hydraulic brake unit may be interrupted.
  the ecu will be rewritten with modified software.

  Show Content

• Recall 2020579 [Canada]: Brakes
  Issue: on certain vehicles, the parking brake operating shaft in the rear brake caliper could rust and become stuck. If this happens, the parking brake may not work properly. As a result, the brakes could drag or parking brake performance could be reduced. If the vehicle is not left in in gear when it is parked, it could roll away. Note: this is an expansion of recall sr-18-002 (transport canada recall no. 2018-053). Safety risk: a parked vehicle that rolls away could create the risk of an injury or a crash. Corrective actions: mitsubishi will notify owners by mail and instruct you to take your vehicle to a dealer to replace the rear brake calipers.

  Show Content

• Recall 2020317 [Canada]: Seats and restraints
  Issue: on certain vehicles, the seat belt buckle for the right seat in the second-row could be damaged when the seats are folded down. This can cause the seat belt buckle cover to come off. If this happens, the seat belt may not latch properly. Safety risk: a seat belt that does not latch properly could create an increased risk of injury in a crash. Corrective actions: mitsubishi will notify owners by mail and instruct you to take your vehicle to a dealer to modify the center seat belt buckle in the second seating row. A warning label will also be attached to the right seat base and additional instructions will be added to the owner's manual.

  Show Content

• Recall 2018053 [Canada]: Brakes
  On certain vehicles, insufficient rust prevention to the parking brake shaft and insufficient sealing performance of the rear brake caliper boot could allow water to penetrate inside these components causing corrosion. As a result, the parking brake shaft may become stuck causing brake dragging and/or decreased parking brake performance. Additionally, the automatic adjuster for the brake pad clearance of the rear brake caliper with the built-in parking brake may not work correctly. These conditions could lead to a vehicle rollaway, which would increase the risk of a crash causing injury and/or damage to property. Correction: dealers will inspect and repair the rear brakes as necessary.

  Show Content

• Recall 2017475 [Canada]: Engine
  On certain vehicles, defective electrical relays may have been installed in the power distribution center. This could cause various electrical circuits to fail, potentially resulting in engine stalling, reduced engine power, or loss of engine cooling fan function potentially resulting in engine overheating. These issues could increase the risk of a crash causing injury and/or damage to property. Correction: dealers will replace affected relay(s) with updated parts.

  Show Content

• Recall 2017198 [Canada]: Structure
  On certain vehicles, the dimensions of some components in certain door latch mechanisms may be out of specification and may not securely latch in high-temperature conditions. If this occurs and a door mechanism does not securely latch, the door could inadvertently open while the vehicle is in motion, which could increase the risk of injury to a vehicle occupant seated next to the door, or result in damage to property. Correction: dealers will replace the affected door latches with countermeasure units.

  Show Content

• Recall 2016379 [Canada]: Powertrain
  On certain vehicles equipped with a continuously variable transmission (cvt), the range switch could momentarily experience a loss of signal. If this occurs, the driver may experience an unexpected reduction of vehicle acceleration which could, in conjunction with traffic, road conditions and the driver's reactions, increase the risk of a crash causing injury and/or damage to property. Correction: dealers will reprogram the cvt-ecu.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

The contact owns a 2016 mitsubishi outlander. The contact stated while driving at various speeds, the steering column vibrated and made an abnormally loud sound. The contact stated no warning light was illuminated. The vehicle was diagnosed but not repaired. The manufacturer was informed of the failure and informed the contact that they were unable to assist. The failure mileage was approximately 95,961.

Wife was driving home from work in the 2016 outlander sport and just before exiting onto the exit ramp vehicle began to rev up and then wind down and wouldn't accelerate anymore. Had it towed to the dealership. They checked it out and the transmission cvt is shot. Mind you this vehicle has only 118,000 and is only 5 yrs. Old and with regular maintenance on it. The dealership just quoted me price to fix it would be $10,000. We still owe about $3500 left on payments. We don't have $10,000 to shell out for another transmission. Did some digging and seems like a lot of people are having the same problem with this transmission. This should be fixed for free and needs to be recalled. Someone is gonna be hurt seriously or killed because of this.

The contact owns a 2016 mitsubishi outlander. The contact stated while driving at various speeds, the rear brakes grabbed and would not disengage when the brake pedal was released. The contact stated no warning light was illuminated. The contact then received notification of nhtsa campaign number: 20v741000 (parking brake). The recall repair was serviced however, the failure still occurred. The vehicle was diagnosed with the brake pads and rotors needing to be replaced. The vehicle was not repaired. The manufacturer had been informed of the failure and referred the contact back to the dealer. The failure mileage was approximately 105,000.

Tl* the contact owns a 2016 mitsubishi outlander. The contact received notification of nhtsa campaign numbers: 20v741000 (parking brake) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. Russ darrow mitsubishi (w226s1700 wi-164, waukesha, wi 53186) and the manufacturer were made aware of the issue. The contact had experienced the failure listed in the recall. The failure mileage was 54,000. Vin tool confirms parts not available.

Tl* the contact owns a 2016 mitsubishi outlander. The contact received notification of nhtsa campaign numbers: 20v741000 (parking brake) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. Russ darrow mitsubishi (w226s1700 wi-164, waukesha, wi 53186) and the manufacturer were made aware of the issue. The contact had experienced the failure listed in the recall. The failure mileage was 54,000. Vin tool confirms parts not available.

Recently replaced the rotors and pads on all four wheels of my outlander. All but the rear passenger are working fine, while the rear passenger side is making a grinding noise. We've replaced the brake pads 3 times, replaced the rotor once, and even replaced the whole caliper; it's still making a grinding sound. There's a recall posted for some 2016 outlanders for the parking brake not engaging/disengaging properly and we might think this is the problem; however, this recall is not applied to our 2016 outlander. I think we are having the exact problem that is listed on this recall.

Vehicle has begun to show issues with transmission. Blinking d light as well as transmission light

Vehicle has begun to show issues with transmission. Blinking d light as well as transmission light

I was at a stop sign turning onto a highway, i accelerated and my car was moved into the middle of the road and my car turned off and then turned back on just a second or so later and i was able to drive again. I am not certain what happened as there were no codes thrown and the car continued to operate after turning itself back on. I am wondering if there is something in the computer programming that is faulty. When i got home, i checked all the connections and did not see any obvious faults. I also checked all fluid levels and caps just to be certain it wasn't something related to any of that somehow. It is scary though because there were vehicles coming toward me from both directions.

Common OBD-II Error Codes

• U0141 [3] Lost Communication With Body Control Module "A"
• P0657 [1] Actuator Supply Voltage "A" Circuit/Open
• P0139 [1] 02 Sensor Circuit Slow Response (Bank 1 Sensor 2)
• P0171 [1] System too Lean (Bank 1)
• P084A [2] Transmission Fluid Pressure Sensor/Switch "H" Circuit
• P2719 [2] Pressure Control Solenoid "D" Control Circuit Range/Performance
• P0969 [2] Pressure Control Solenoid "C" Control Circuit Range/Performance
• P0730 [2] Incorrect Gear Ratio
• P0741 [2] Torque Converter Clutch Circuit Performance or Stuck Off
• P0776 [2] Pressure Control Solenoid B Performance or Stuck Off