Prevost H3-45 Vip 2015

Vehicle Details: Recalls, Investigations, Service Bulletins

Below you will find all available information on the 2015 PREVOST H3-45 Vip.

ManufacturerKnown WMI(s)Fuel Type
PREVOST
PREVOST VIN Decoder

Use the box here to look up VINs from PREVOST as well as other manufacturers

#

Sub-models: - H3-45 Vip Coach -

Frequently Asked Questions
  • Are there recalls for the 2015 PREVOST H3-45 Vip?
     - There are 10 recall(s) for the 2015 PREVOST H3-45 Vip, additional information is below.
NHTSA Mandated Recalls
  • Recall 260236 [USA]: Beacons that do not provide proper illumination may be less visible to wheelchair lift users, increasing the risk of injury.

  • Recall 191691 [USA]: An overheated alternator bearing can increase the risk of a fire.

  • Recall 140670 [USA]: If the fire suppression system does not work as intended, it can increase the risk of injury in the event of a fire.

  • Recall 133690 [USA]: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.

  • Recall 138354 [USA]: If the fuel tank separates from the vehicle, it could be a road hazard and the vehicle would stall. either scenario increases the risk of a crash.

  • Recall 122304 [USA]: If the fasteners loosen, the trailer hitch may deform or detach from the vehicle, increasing the risk of a crash.

  • Recall 109932 [USA]: Contact between the fuel line and the coolant line may cause a fuel leak and result in fuel spraying onto hot exhaust components increasing the risk of an engine compartment fire.

  • Recall 113442 [USA]: Suspension bolt failure may cause a loss of vehicle control, increasing the risk of a vehicle crash.

  • Recall 112417 [USA]: In the event of a fire, if the fire extinguisher does not work correctly, there is an increased risk of injury to the bus occupants.

  • Recall 2015087 [Canada]: Accessories

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • IS-23019 - SUSPENSION: Sway bar collars improvement
  • IS-22106 - EQUIPMENT: H3 lavatory fan retrofit kit
  • IS-21089 - ENGINE AND ENGINE COOLING: Efd h3 vip condenser repositioning
  • IS-18106 - STEERING: Kit power steering tank convertion cummins to zf with d13 engine
  • MI16-32 - ENGINE AND ENGINE COOLING: Improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • IS-19910i - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with delco remy alternator. Revision : i note added regarding power cable connection
  • IS-19900J - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with bosch alternator. Revision : j - note added regarding power cable connection
  • IS-21072B - ELECTRICAL SYSTEM: Steering gateway. Revision b - pin 2 and 10 were inverted on connector a139
  • MI22-12B - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: b - general update
  • MI22-12A - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: a - erroneous secondary & accessory tanks location.
  • MI22-12 - SERVICE BRAKES, AIR: Air tanks draining sequence
  • IS-17151C - EXTERIOR LIGHTING: Halogen to led fog light replacement kit. Revision: c - advanced kits canceled
  • IS-22902 - WHEELS: Tag axle hub flange - alternate cap screw
  • IS21-072 - ELECTRICAL SYSTEM: Steering gateway, revision a : cancel watch dog removal from efd part of the instruction
  • MI20-08C - EQUIPMENT: Storage and startup guidelines : part number updates
  • IS21-072A - ELECTRICAL SYSTEM: Steering gateway revision a cancel watch dog removal from efd part of the instruction
  • IS20-925A - VISIBILITY: Central hvac merv filters installation
  • IS20-932A - EQUIPMENT: H3 series envirocare - ions air sanitizer
  • IS22-040 - EQUIPMENT ADAPTIVE/MOBILITY: Brake pedal seal plate installation kit
  • IS19_908E - ELECTRICAL SYSTEM: Bosch to delco remy alternator installation, h3-45 revision : e, updated electrical schematic. Added instructions for h series ghg17 engine variant.
  • MI18-16B - ELECTRICAL SYSTEM: Bosch hd10 alternator diagnostic guide revision b to avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
  • MI21-06 - FUEL SYSTEM, DIESEL: Diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair ⿿ from us10 to newer engine generation
  • Mi21-07A - WHEELS: Ront & tag axle ⿿ unitized hub bearing end play verification and replacement
  • is_20089 - LATCHES/LOCKS/LINKAGES: Lavatory compartment sliding door latch improvement
  • MI20-08C - STRUCTURE: Storage and startup guidelines: periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, prevost recommends foll
  • IS-20925A - POWER TRAIN: Central hvac merv filters installation reva
  • IS-20932A - EQUIPMENT: H3 series envirocare - ions air sanitizer rev a
  • VBC-PREVOST 2 - EQUIPMENT ADAPTIVE/MOBILITY: Bendix m-32qr abs modulator valve replaced by new m-40qr valve.
  • VBC-PREVOST 1 - EQUIPMENT:MECHANICAL:BOOM/CRANE/LADDER:HOSES/CABLES/RODS/GEARS/STRUT/CYLINDER: Communication letter from accociate administration for enforcement, nhtsa from prevost subject vehicle brand: prevost (ewr#000650)
  • IS-20932 - EQUIPMENT: H3 series envirocare - ions air sanitizer
  • IS-18091A - STEERING: Tie rod 610052 first installation instructions: use these instructions when replacing the drop joint tie rod on s82, s84 / s84u i-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment ne
  • MI20-19B - ENGINE AND ENGINE COOLING: Introducing a new engine coolant into prevost service center network
  • MI20-19A - ENGINE AND ENGINE COOLING: Rev a: mention added concerning ddc series 60 engine sca requirement
  • MI21-01 - EQUIPMENT: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI21-01 - POWER TRAIN: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI20-19 - EQUIPMENT: Introducing a new engine coolant into service
  • MI02-17A - EQUIPMENT ADAPTIVE/MOBILITY: Revision : a torque value reduced
  • WB16-02D - BACK OVER PREVENTION:SOFTWARE: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system. The corrective measures of this bulletin are very important and must all be c
  • IS-14145 - ELECTRICAL SYSTEM: This instruction sheet explains how to add sunshade switches on the dashboard
  • MI16-17D - SEATS: Use this procedure for the removal and installation of the twin bosch hd10 (120a or 150a) alternators.
  • MI18-02A - ENGINE AND ENGINE COOLING: Engine oil & filter change intervals - volvo d13 engine, from us10 revision: a updated for obd20 engines
  • IS-19165A - ELECTRICAL SYSTEM: Lavatory fan retrofit kit applicable for h3 series coaches from r-1012 (1994) revision a: added installation detail at step 8
  • IS-13169A - BACK OVER PREVENTION: SENSING SYSTEM: RADAR: Prevost aware adaptive cruise braking (acb) flr20 radar sensor replacement kit revision a: kit is13169-1 & is13169-2 canceled, use 145373 &145372
  • IS-20923 - EQUIPMENT: H3 driver⿿s partition lite installation
  • IS-20929 - EQUIPMENT: Uv lights installation in ac compartment
  • IS-20929 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Uv lights installation in a/c compartment
  • P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • U17_P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • MI20-08B - EQUIPMENT: Storage and startup guidelines revision: b parts added to suggested material 08-10-2020
  • IS-20922 - EQUIPMENT ADAPTIVE/MOBILITY: Sigma passenger seats partition kit
  • MI18-18B - EQUIPMENT: General hoisting and towing procedures revision: b updated 2.1 to show rubber chocks, secure front and rear.
  • MI20-12 - STEERING: Jerky, noisy or hard to turn steering gearbox. Hydraulic end limiter adjustment. All models ⿿ equipped with rb bosch/zf servocom or servocomtronic steering gearbox
  • IS-09900i - EQUIPMENT ADAPTIVE/MOBILITY: Electric fan drive cooling system conversion with bosch alternator revision i: parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal, st,16
  • IS-19910H - ENGINE (PWS): Electric fan drive cooling system conversion with delco remy alternator revision h: parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal,
  • IS-20906 - EQUIPMENT ADAPTIVE/MOBILITY: Plexiglass shield behind driver h3 series
  • MI20-08A - EQUIPMENT: Storage and startup guidelines: rev a: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
  • MI20-09 - EQUIPMENT: Prevost vehicle disinfection procedure revision a
  • IS-19084 - EQUIPMENT: Accessory air filter replacement replaces 642192
  • U17_P040200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • U02A200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes U02A200 lost communication with reductant quality module
  • U029E00 - ENGINE (PWS): Repair instructions to address fault codes U029E00 lost communication with nox sensor "b"
  • U029D00 - ENGINE (PWS): Repair instructions to address fault codes U029D00 lost communication with nox sensor "a"
  • P256000 - EQUIPMENT: Repair instructions to address fault codes P256000 engine coolant level low
  • P242A15 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P242A15 exhaust gas temperature sensor bank 1 sensor 3 - circuit short to battery or open
  • P20E892 - EQUIPMENT: Repair instructions to address fault codes P20E892 reductant pressure too low - performance orincorrect operation
  • P208464 - EQUIPMENT: Repair instructions to address fault codes P208464 exhaust gas temperature sensor circuit range/performance bank 1 sensor 2 - signal plausibility failure
  • P204A13 - EQUIPMENT: Repair instructions to address fault codes P204A13 reductant pressure sensor - circuit open
  • P204713 - EQUIPMENT: Repair instructions to address fault codes P204713 reductant injection valve control bank 1 unit 1 ⿿ circuit open
  • P203F00 - EQUIPMENT: Repair instructions to address fault codes P203F00 reductant level low
  • P203115 - EQUIPMENT: Repair instructions to address fault codes P203115 exhaust gas temperature sensor bank 1 sensor 2 - circuit short to battery or open
  • P10CE97 - EQUIPMENT: Repair instructions to address fault codes P10CE97 reductant return: no flow detected - componentor system operation obstructed or blocked
  • P107575 - EQUIPMENT: Repair instructions to address fault codes P107575 clutch system - emergency position not reachable
  • P107017 - BRAKES (PWS): Repair instructions to address fault codes P107017 gearbox brake valve (vagb) - circuit voltage above threshold
  • P105998 - POWER TRAIN: Repair instructions to address fault codes P105998 gearbox oil temperature sensor - component orsystem over temperature
  • P054415 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P054415 exhaust gas temperature sensor bank 1 sensor 1 - circuit short to battery or open
  • P052400 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P052400 engine oil pressure too low
  • P040200 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • P029800 - ENGINE (PWS): Repair instructions to address fault codes P029800
  • P021700 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P021700 engine coolant over temperature condition
  • NOx_Conv2 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P207F-00; P20EE-00
  • NOX_Conv1 - EQUIPMENT ADAPTIVE/MOBILITY: Repair instructions to address fault codes P207F-00 - reductant quality
  • FUELFILTER - ENGINE (PWS): Repair instructions to address fault codes P008A-00; P0087-00
  • MI20-09 - EQUIPMENT:OTHER:LABELS: Prevost vehicle disinfection procedure
  • MI20-08 - UNKNOWN OR OTHER: Storage and startup guidelines - all prevost vehicles & volvo 9700
  • IS-20905 - EQUIPMENT: Hand sanitizer dispenser installation
  • IS-19064 - STRUCTURE: Baggage door seal replacement
  • MI15-24 - EQUIPMENT ADAPTIVE/MOBILITY: Added: power cables for l.H. Side alternator & fan drive breaker box
  • IS-14076 - EQUIPMENT: This instruction sheets explains how to replace the fuel tank on h-series vehicles. (replacing older series tanks by newer model)
  • IS-19910G - ENGINE AND ENGINE COOLING: Revision : mention added stating to disable prime.
  • IS-19900H - ENGINE AND ENGINE COOLING: Revision : mention added in the instruction sheet stating to disable "prime"
  • IS-19921A - EQUIPMENT: This instruction sheet explains how to install a seatbelt cutter in the driver's area
  • IS-19066 - SERVICE BRAKES, AIR: This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
  • SCI19-01C - ELECTRICAL SYSTEM: The intent of this procedure is to guide you through the steps required to program a mcm especially for the control of the electric fan drive as required for conversion kit of instruction sheets is-19900, is-19901, is19910, is-19912.
  • IS-19900G - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric fan drive cooling system conversion kit with bosch alternator - h3 series us10 cooling system
  • IS-19043 - EQUIPMENT: This instruction sheet explains how to relocate the wheel chair lift parcel rack fan
  • IS-17151 - LIGHTING (PWS): This instruction sheet explains how to replace halogen fog light to led's
  • IS-19910E - ELECTRICAL SYSTEM: This instruction sheet explains how to perform an electric fan drive cooling system conversion with delco remy alternator - h3 series us10 to ghg17 included
  • IS-19910D - ELECTRICAL SYSTEM: This instruction sheet explains how to perform an electric fan drive cooling system conversion with delco remy alternator - h3 series us10 to ghg17 included
  • IS-19900E - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric fan drive cooling system conversion kit with bosch alternator - h3 series us10 cooling system
  • IS-18091 - STEERING: This instruction sheet explains how to perform the first installation of tie rod 610052 on prevost vehicles equipped with dana s82, s84 / s84u i-beam axles, 1994- today
  • WB19-14 - ELECTRICAL SYSTEM: Neutral gear - software update
  • MI18-45A - POWER TRAIN: Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to is-18091 for installation instruction
  • Mi14-34D - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: Prevost aware adaptive cruise braking (acb) - flr20 & flr21 radar sensor alignment
  • IS-19915 - EQUIPMENT: Mp-1000 multimedia player installation
  • IS-19910C - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator - h3 series us10 up to ghg17
  • IS-19900D - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with bosch alternator - h3 series us10 cooling system
  • IS-18910 - EQUIPMENT: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-18091 - SUSPENSION: This instruction sheet explains how to install the tie rod 610052.
  • IS-18025A - SUSPENSION: This instruction sheet shows how to replace kneeling level sensor #21643575 by sensor #22194741.
  • IS-17900A - STRUCTURE: Wheel fender stainless steel protector
  • IS-18025A - SUSPENSION: This instruction sheet shows how to replace kneeling level sensor #21643575 by sensor #22194741.
  • WB19-07 - SERVICE BRAKES, AIR: On the independent front suspension (ifs) of the vehicles affected by this bulletin, check and make sure that there is enough clearance between the brake hoses identified in the procedure and their respective support bracket.
  • IS-19908E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on h3 vehicles
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-19908A - ELECTRICAL SYSTEM: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on h3 vehicles
  • IS-19900A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to convert h3 series us10 vehicles equipped with bosch alternators to electric fan drive (efd) cooling system
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet explains how to install a flap over the diesel filling cap
  • IS-18115 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to install a gm glove box lock on h-series vehicles
  • IS-17071A - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • SCI19-01A - ELECTRICAL SYSTEM: This procedure explains how to program a mcm especially for the control of the electric fan drive, as required for conversion kit of instruction sheets is-19900 & is-19910.
  • MI19-06 - BRAKES (PWS): This maintenance information is published to answer some questions regarding the inverted or ?Trailing? Mounting position of the drive axle brake calipers on prevost vehicles
  • MI19-05 - EQUIPMENT: This maintenance information expains how to adjust p/n 660865, 660699 draglinks
  • IS-19910 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to convert h3 series us10 vehicles (equipped with delco remy alternators) to electric fan drive (efd) cooling system
  • IS-19908 - ELECTRICAL SYSTEM: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on h3 vehicles
  • IS-19900 - ENGINE AND ENGINE COOLING: This instruction sheet explains how to convert h3 series us10 vehicles equipped with bosch alternators to electric fan drive (efd) cooling system
  • IS-15075 - STRUCTURE: This instruction sheet explains how to replace fenders made of fiber glass with aluminium
  • SCI19-01 - EQUIPMENT: This procedure explains how to program a mcm especially for the control of the electric fan drive, as required for conversion kit of instruction sheets is-19900 & is-19910.
  • SCI18-46 - EQUIPMENT:ELECTRICAL: This service center instructions explains how to install the prevost ultimate entertainment system
  • Wb17-14B - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the power cable stud adapter on the alternator must be inspected and if needed, replaced.
  • IS-18905 - EQUIPMENT: This instruction sheet explains how to install hatches with fan on h3 vehicles.
  • WB18-43 - POWER TRAIN: This warranty bulletin explains how to update the vecu (vehicle electronic control unit) parameters to allow auto engine brake function with the i-shift transmission.
  • WB18-04 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available.
  • MI18-37 - POWER TRAIN:AUTOMATIC TRANSMISSION: This maintenance information presents information about the removal or installation of the lang kk73.1 electromagnetic clutch - part of the bitzer (model 4nfcy) air conditioning compressor.
  • MI18-21A - ENGINE AND ENGINE COOLING: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-18A - EQUIPMENT: This maintenance information explains how to tow and hoist prevost vehicles.
  • MI16-17G - ENGINE AND ENGINE COOLING: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • WB18-01A - STRUCTURE: On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
  • WB16-02H - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system.
  • IS-15003E - ELECTRICAL SYSTEM: This insruction sheet explains how to insall the bosch hd10 24v-150a alternator conversion kit ? Twin bosch mounted on volvo d13 engine
  • MI18-18 - EQUIPMENT:MECHANICAL:WRECKER AND WHEEL LIFT DEVICES: This maintenance information explains how to tow and hoist prevost vehicles.
  • MI18-21 - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-16A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information presents guidelines to help with the diagnosis of the bosch hd10 alternators
  • IS-18902 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to installa parcel rack door kits
  • WB18-15 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, the instrument cluster software must be updated. This mandatory cluster software update will raise the primary and secondary air system ?Low pressure warning? Set point.
  • IS-17905 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-13009B - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install and adjust drag link # 660699
  • WB15-19H - EQUIPMENT:APPLIANCE:AIR CONDITIONER: This bulletin explains how to add a reinforcement bracket to bitzer a/c compressor to increase the installation stiffness and reduce vibration amplitude.
  • MI18-02 - ENGINE AND ENGINE COOLING: This mainteannce informaiton presents the latest engine oil & filter change intervals for the volvo engine
  • MI16-17F - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • MI1434C - VEHICLE SPEED CONTROL:CRUISE CONTROL: This maintenance information presents how to align the prevost aware adaptive cruise braking (acb)flr20 radar sensor.
  • WB14-06G - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, perform the following verifications and modifications on the a/c system: bulletin is divided in five steps, refer to detailed instructions below. Step 1: unloader replacement (step moved to war
  • WB14-28E - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, replace the ltd, relocate and replace the ir sensor as described in the following procedure.
  • SP15-60 - WHEELS: On the vehicles affected by this bulletin, there is a contact possibility between some parts of the ifs suspension components and steering linkage when the wheels are rotated to their maximum left or right position and the suspension is ful
  • MI15-51 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: This maintenance information explains how to run a n air conditionning performance test
  • MI15-61 - ENGINE (PWS): This maintrenance infomration explains that the castrol syntrans oil isn?T fully approved for 500 000 miles (800 000 km) extended drain intervals on the volvo i-shift transmission. For this reason, this oil has been downgraded to regular d
  • IS-15907A - EQUIPMENT:MECHANICAL: This instruction sheet explains how to assemble the bendix flr10 and flr20 radar sensor alignment tool
  • WB15-53A - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles covered by this bulletin, two dpf (diesel particulate filter) plugs may be loose. If a plug is loose, it may fall out under the effect of vibration. This may cause leakage of hot exhaust gases. It is therefore necessary to c
  • MI15-45 - STRUCTURE:FRAME AND MEMBERS: This maintenance information exlpains how to install kit mi15-45 frame reinforcement, in case a stress crack develops on the left rear frame support beam
  • WB15-39 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, the entrance door locking mechanism may occasionally fail to function properly and stay in the locked position, hindering the door opening. To prevent this situation, a new improved mechanism will
  • WB15-46 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL: On the vehicles affected by this bulletin the epa (us environment protection agency) decal located in the engine compartment displays incorrect information related to the vehicle emission control. Specifically, the first character, indicati
  • SP15-31C - SUSPENSION: Two cases of dana i-beam axles were reported to the operations having a minor issue. This special bulletin is targeting a wide array of vehicles to be inspected in order to determine the potential of defect related to this issue.
  • IS-14076 - FUEL SYSTEM, GASOLINE:STORAGE:AUXILLARY TANK: This instruction sheet does explain how to proceed to the fuel tank replacement, from # 031868 tank by newer 030008 model.
  • SP15-07B - FUEL SYSTEM, DIESEL: Following wb13-04, update the hot gas pickup tube circuit for an improved version with a better resistance to vibrations. This bulletin resolves a/c low pressure messages in the dashboard when the auxiliary fan is not running. The valve wil
  • MI15-41 - EXTERIOR LIGHTING:TAIL LIGHTS: This maintenance information reminds prevost customers that cleaning products designed for external washing of vehicles should be used for exterior vehicle wash and in particular, for the washing of polycarbonate taillights.
  • MI15-43 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on prevost vehicles equipped with bosch hd10 alternators.
  • MI15-18 - EQUIPMENT: This maintenance information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.
  • MI15-24 - EQUIPMENT:MECHANICAL: This maintenance information explains how to perform an inspection of the vehicle power cables. Power cables in poor condition can be the cause of failures and serious damages in the engine compartment.
  • SP15-31_FR - SUSPENSION: Two cases of dana i-beam axles were reported to the operations having a minor issue. This special bulletin is targeting a wide array of vehicles to be inspected in order to determine the potential of defect related to this issue.
  • WB15-26 - SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS: On the vehicles affected by this bulletin the brake hose may come in contact with the air spring support when the front axle is in low or high position, either by kneeling or low-high buoy. Perform an inspection. Depending on the result, ad
  • WB15-25 - SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS: On the vehicles affected by this bulletin inspect the clamp retaining the brake hose supports to make sure it does not contact with the shock absorber.
  • SP15-23 - SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY:U-BOLT, LEAF SPRING TO AXLE: On the vehicles affected by this bulletin, the bolts of the steer lever might not be per specifications. Inspect per procedure below and replace as needed.
  • WB15-10 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, inspect the lower oil fill tube flexible tube. If it is made of black material (edpm), replace tube. Green and blue silicone hoses are accepted.
  • IS-15003A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to use the bosch hd10 24v-150a altenrator conversion kit
  • SP15-15A - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform software updates of the engine management system (ems) and instrument cluster. The cluster update affects the beep sound level. Some vehicles will need both systems updated. Other vehicles
  • IS-13169A - BRAKES (PWS): This instruction sheet explains how to install the aware adaptive cruise braking (acb) flr20 radar sensor replacement kits # 145372 and 145373
  • IS-17907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the volvo electronic logging device (eld)
  • IS-17071 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • IS-17016 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruciton sheet explains how to relocate the rv-3 valve
  • Wb18-01 - LATCHES/LOCKS/LINKAGES:DOORS:LATCH: On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
  • MI17-22 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: This maintenance information explains how to inspect the fuel tank cradle mounting screws on a yearly basis
  • IS-17043A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to optimise the operation of the lavatory fan
  • WB15-06C - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: On the vehicles affected by this bulletin, inspect the serial number of the current sensors in the battery compartment and follow instructions to perform replacement if applicable. A number of sensors have been identified by the manufacture
  • WB15-13 - SUSPENSION: On the independent front suspension level valve linkage of the vehicles affected by this bulletin, a control rod may come in contact with an air reservoir outlet when vehicle rises from low to high buoy. As a result, the vehicle may be leve
  • WB15-06B - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: On the vehicles affected by this bulletin, inspect the serial number of the current sensors in the battery compartment and follow instructions to perform replacement if applicable. A number of sensors have been identified by the manufacture
  • IS-13106 - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install an improved version of the slide-out rails. This version of the rails offers better corrosion resistance.
  • MI15-02 - POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT: This maintenance information presents an improved differential breather kit, identical to the one now used in production. This new breather incorporates a "j" shaped hose that prevents oil leakage and water ingestion while allowing the axle
  • WB14-47B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a software update of ecm (engine control module) and acm (aftertreatment control module) to provide improved temperature-related behaviour. The software will also change urea dosing valve b
  • Wb15-19F - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • Mi16-15 - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • WB17-02 - ENGINE AND ENGINE COOLING: This bulletin explains how install an extension to the linear thermal detector (ltd) over the alternators
  • IS-17900A - WHEELS: This instruction sheet explains how to install a wheel fender stainless steel protector
  • IS-15003D - ELECTRICAL SYSTEM: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • IS-17043 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to optimise the operation of the lavatory fan
  • CK17-30 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is now possible to replace the older generation tgw 2.0 (3g network) by the newer 2.1 version (4g the network) using accessory kit 23266301 and the following procedure.
  • SCI16-40 - ENGINE (PWS): On the vehicles affected by this bulletin, replace the engine information decal located in the engine compartment. (internal procedure)
  • WB16-33 - ENGINE (PWS): On the vehicles affected by this bulletin, replace the engine information decal located in the engine compartment.
  • MI16-32 - POWER TRAIN:DRIVELINE:CENTER SUPPORT BEARING: Explains that improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • MI15-43A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on prevost vehicles.
  • WB15-44A - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, the equipment used to tighten the wheel lugs in a visit to one of our service center between november 2014 and june 2015, was found to be out of specification, possibly delivering a torque value i
  • WB15-19 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • WB15-10A - ENGINE (PWS): On the vehicles affected by this bulletin, inspect the lower oil fill tube flexible tube. If it is made of black material (edpm), replace tube. Green and blue silicone hoses are accepted.
  • SP15-07 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Following wb13-04, update the hot gas pickup tube circuit for an improved version with a better resistance to vibrations. This bulletin resolves a/c low pressure messages in the dashboard when the auxiliary fan is not running. The valve wil
  • WB15-26B - SUSPENSION: On the vehicles affected by this bulletin the brake hose may come in contact with the air spring support when the front axle is in low or high position, either by kneeling or low-high buoy. Perform an inspection. Depending on the result, ad
  • SP15-15B - ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL: On the vehicles affected by this bulletin, perform software updates of the engine management system (ems) and instrument cluster. The cluster update affects the beep sound level. Some vehicles will need both systems updated. Other vehicles
  • WB15-06D - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, inspect the serial number of the current sensors in the battery compartment and follow instructions to perform replacement if applicable. A number of sensors have been identified by the manufacture
  • CK17-27 - EQUIPMENT ADAPTIVE/MOBILITY: This conversion kit explains how to to disable the acb radar.
  • SP16-43A - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, coolant may leak by the coolant level sensor wires on the surge tank. Replace the sensor with an improved version.
  • WB16-33A - ENGINE (PWS): On the vehicles affected by this bulletin, replace the engine information decal located in the engine compartment.
  • SCI16-40A - ENGINE (PWS): On the vehicles affected by this bulletin, replace the engine information decal located in the engine compartment.
  • IS-15003B - EQUIPMENT: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • MI16-15B - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • WB16-02B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system.
  • Wb16-29 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available. This update must be carried out by qualified technicians. As soon as possible, make an appointment with your nearest prevost service cen
  • MI16-14 - SUSPENSION: Use this procedure when a suspension height check or adjustment must be performed.
  • Mi16-28 - VISIBILITY:REARVIEW MIRRORS/DEVICES: This maintenance information explains that on vehicles equipped with ramco rear-view mirrors in winter conditions, ice may accumulate in the gap between the glass bottom edge and shell. The ice may impede mirror adjustment. Installing a dri
  • WB16-02 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system.
  • MI16-23 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information explains that decals are available to update the front junction box on 2013 to 2016 prevost vehicles; the decals will provide updated information and component descriptions. Refer to the identification part of t
  • MI16-15A - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • MI16-10 - WHEELS: This information letter applies only to vehicles equipped with 19000 lb independent front suspension (ifs) and 22.5 x 10.5 alcoa aluminum wheels for 365/70 r 22.5 size tires. When balancing this wheel for installation on the ifs, a specifi
  • IS-14085 - EQUIPMENT: This instruction sheet explains how to prevent ac copper pipes chaffing at engine bulkhead
  • MI16-16 - ELECTRICAL SYSTEM: This procedure explains how to perform a starter removal and installation, and does apply to melco 105p70 starter part number #21212425.
  • WB15-55 - POWER TRAIN:AXLE ASSEMBLY: On the vehicles affected by this bulletin, inspect the gap between the radius rod support and the front axle. A deviation in the axle beam envelope can lead to interference between the two parts. In most cases, slightly moving the support w
  • WB16-04 - STEERING: On the vehicles affected by this bulletin the steering damping cylinder rod end spherical bearing may be loose in its housing. Replace as required and secure the steering damper spherical bearing with the provided hardware.
  • MI16-05 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information shares information about the bendix m-32qr valve replaced by m-40qr model htat need to be taken into consideration, specially when switching them for the first time on a vehicle.
  • CK17-19A - EQUIPMENT: This conversion kit explains how to remove tgw1 from vehicles using tech tool, no manual vda changes needed. This conversion kit will work for any vehicle equipped with tgw1 up to the vin's listed on the bulletin.
  • WB15-19E - EQUIPMENT: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • IS-15003D - ENGINE (PWS): This insruction sheet explains how to insall the bosch hd10 24v-150a alternator conversion kit ? Twin bosch mounted on volvo d13 engine
  • WB16-02C - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system. The corrective measures of this bulletin are very important and must all be ca
  • MI16-10A - WHEELS: This maintenance information applies only to vehicles equipped with 19000 lb independent front suspension (ifs) and 22.5 x 10.5 alcoa aluminum wheels for 365/70 r 22.5 size tires. When balancing this wheel for installation on the ifs, a spe
  • WB14-47B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a software update of ecm (engine control module) and acm (aftertreatment control module) to provide improved temperature-related behaviour. The software will also change urea dosing valve b
  • WB14-45C - ELECTRICAL SYSTEM:WIRING: On the vehicles affected by this bulletin remove the acm relay and base identified r49. Reconnect the 24v power wire and protect the remaining signal wires with shrink tube.
  • IS-13169 - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: This instruction sheet explains how to install the aware adaptive cruise braking (acb) flr20 radar sensor replacement kits # 145372 and 145373
  • SP14-46 - EQUIPMENT ADAPTIVE/MOBILITY: This bulletin is performed on a fix as fail basis. On the vehicles affected by this bulletin, update to the latest configuration of wiring and sensors for the bitzer compressor.
  • WB14-44B - EQUIPMENT:ELECTRICAL: On the vehicles affected by this bulletin, changing of vecu (vehicle electronic control unit) parameters is necessary. This update must be carried out by qualified technicians. Make an appointment with your nearest prevost service center.
  • WB14-39 - EQUIPMENT:OTHER:LABELS: On the vehicles affected by this bulletin inspect a power cable going to the condenser fan motor. After inspection, add a decal inside the a/c control box cover.
  • WB14-42A - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a power source improvement and a multiplex software update for the steering gateway module. On a limited number of vehicles, the module will be replaced with the latest version of the part.
  • SP14-38 - STRUCTURE:BODY:BUMPERS: The concerned vehicle had a spare front bumper hinges to be replaced by original ones
  • WB16-02E - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system.
  • MI16-17E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternator.
  • IS-17900 - EQUIPMENT: This instruction sheet explains how to install a wheel fender stainless steel protector
  • IS-15003C - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • WB15-19G - EQUIPMENT: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • MI16-34 - ELECTRICAL SYSTEM: "this maintenance information describes the steps to be followed on your computer to add the volvo engine brake auto mode on the vehicle. The auto mode may be added on us10 and obd13 vehicles that were built before the introduction of the
  • WB15-55 - STEERING:LINKAGES:TIE ROD ASSEMBLY: Radius rod support and i-beam axle gap inspection on the vehicles affected by this bulletin, inspect the gap between the radius rod support and the axle. A deviation in the axle beam envelope can lead to interference between the two part
  • WB15-39 - STRUCTURE:BODY:DOOR : Summary to be provided on a future date.
  • WB15-26 - SERVICE BRAKES, AIR:SUPPLY:HOSES, LINES/PIPING, AND FITTINGS: Summary to be provided on a future date.
  • WB15-10 - ENGINE (PWS): Summary to be provided on a future date.
  • SP15-23 - WHEELS:LUGS/NUTS/BOLTS: Summary to be provided on a future date.
  • SP-15-23 - EQUIPMENT: Prevost: specifications of bolts of steer lever, on some buses, was not met and inspection is needed and replacement of bolts, if needed. Model 2015 h3-45, x3-45. *pe
Known Recall Investigations
  • Alternator front bearing failure investigation # PE21011

    Nhtsas office of defects investigation (odi) is opening a preliminary evaluation after receiving a tip from a fleet safety manager concerning alternator front bearing failures that cause elevated temperatures within the engine compartment, resulting in the fire suppression system (fss) activating, immediately shutting the engine down, and rendering the bus inoperable. Review of early warning reporting data identified 9 field reports for model year (my)2015 through my2019 h3 and x3 prevost buses, describing alternator failures in any of 3 alternators equipped on the bus. In some cases, a minor fire occurred damaging nearby electrical harnesses. An immediate shut down of the bus can increase the risk of a crash or injury of passengers when transferring to another bus.Odi is opening this investigation to evaluate the cause, consequence, scope and frequency of the alleged defect in the subject prevost buses.

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.